MC10EP445, MC100EP445 3.3V/5VECL 8−Bit Serial/Parallel Converter Description The MC10/100EP445 is an integrated 8–bit differential serial to parallel data converter with asynchronous data synchronization. The device has two modes of operation. CKSEL HIGH mode is designed to operate NRZ data rates of up to 3.3 Gb/s, while CKSEL LOW mode is designed to operate at twice the internal clock data rate of up to 5.0 Gb/s. The conversion sequence was chosen to convert the first serial bit to Q0, the second bit to Q1, etc. Two selectable differential serial inputs, which are selected by SINSEL, provide this device with loop−back testing capability. The MC10/100EP445 has a SYNC pin which, when held high for at least two consecutive clock cycles, will swallow one bit of data shifting the start of the conversion data from Dn to Dn+1. Each additional shift requires an additional pulse to be applied to the SYNC pin. Control pins are provided to reset and disable internal clock circuitry. Additionally, VBB pin is provided for single−ended input condition. The 100 Series contains temperature compensation. Features • • • • • • • • • • • 1530 ps Propagation Delay 5.0 Gb/s Typical Data Rate for CLKSEL LOW Mode Differential Clock and Serial Inputs VBB Output for Single-Ended Input Applications Asynchronous Data Synchronization (SYNC) Asynchronous Master Reset (RESET) PECL Mode Operating Range: VCC = 3.0 V to 5.5 V with VEE = 0 V NECL Mode Operating Range: VCC = 0 V with VEE = −3.0 V to −5.5 V Open Input Default State CLK ENABLE Immune to Runt Pulse Generation Pb−Free Packages are Available* http://onsemi.com MARKING DIAGRAM* MCxxx EP445 AWLYYWWG LQFP−32 FA SUFFIX CASE 873A xxx A WL YY WW G = 10 or 100 = Assembly Location = Wafer Lot = Year = Work Week = Pb−Free Package *For additional marking information, refer to Application Note AND8002/D. ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 16 of this data sheet. *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. © Semiconductor Components Industries, LLC, 2006 July, 2006 − Rev. 11 1 Publication Order Number: MC10EP445/D VCC Q2 Q1 VCC Q0 PCLK PCLK VCC MC10EP445, MC100EP445 Table 1. PIN DESCRIPTION 24 23 22 21 20 19 18 Function Pin 17 SINSEL 25 16 VEE SINA*, SINA* ECL Differential Serial Data Input A SINB 26 15 Q3 SINB*, SINB* ECL Differential Serial Data Input B SINB 27 14 Q4 VEE 28 VBB0 29 MC10EP445 MC100EP445 VCC PCLK, PCLK ECL Differential Parallel Clock Output SYNC* ECL Conversion Synchronizing Input CKSEL* ECL Clock Input Selector Pin CKEN* ECL Clock Enable Pin RESET* ECL Reset Pin VBB0, VBB1 Output Reference Voltage VCC Positive Supply VEE Negative Supply Q5 SINA 31 10 Q6 VCC 32 9 Q7 7 8 VCC CKSEL 6 VBB1 5 CLK CLK CKEN SYNC RESET 4 ECL Differential Clock Inputs CLK*, CLK* 12 11 3 ECL Parallel Data Outputs VCC 30 2 ECL Serial Input Selector Pin Q0−Q7 13 SINA 1 SINSEL* * Pins will default logic LOW or differential logic LOW when left open. Warning: All VCC and VEE pins must be externally connected to Power Supply to guarantee proper operation. Figure 1. 32−Lead LQFP Pinout (Top View) Table 2. TRUTH TABLE FUNCTION High PIN SINSEL CKSEL Low Select SINB Input Select SINA Input Q: PCLK = 8:1 CLK: Q = 1:1 Q: PCLK = 8:1 CLK: Q = 1:2 CLK CLK Q Q CKEN Synchronously Disable Internal Clock Circuitry Synchronously Enable Internal Clock Circuitry RESET Asynchronous Master Reset Synchronous Enable SYNC Asynchronously Applied to Swallow a Data Bit Normal Conversion Process http://onsemi.com 2 MC10EP445, MC100EP445 SINA VEE SINA SINB 1:2 DEMUX SINB 1:2 DEMUX 1:2 DEMUX SINSEL 1:2 DEMUX CKEN T C Q4 Q2 Q6 Q 1:2 DEMUX R T C Q0 1:2 DEMUX Q R 1:2 DEMUX SYNC Q1 Q5 Q3 Q7 Control Logic DIV2 CLK PCLK DIV2 PCLK CLK CKSEL RESET Figure 2. Logic Diagram Table 3. ATTRIBUTES Characteristics Value Internal Input Pulldown Resistor 75 k Internal Input Pull−up Resistor ESD Protection N/A Human Body Model Machine Model Charged Device Model Moisture Sensitivity, Indefinite Time Out of Drypack (Note 1) LQFP−32 Flammability Rating Oxygen Index: 28 to 34 Transistor Count > 2 kV > 200 V > 2 kV Pb Pkg Pb−Free Pkg Level 2 Level 2 UL 94 V−0 @ 0.125 in 993 Devices Meets or exceeds JEDEC Spec EIA/JESD78 IC Latchup Test 1. For additional information, see Application Note AND8003/D. http://onsemi.com 3 MC10EP445, MC100EP445 Table 4. MAXIMUM RATINGS Symbol Rating Unit VCC PECL Mode Power Supply Parameter VEE = 0 V Condition 1 6 V VEE NECL Mode Power Supply VCC = 0 V −6 V VI PECL Mode Input Voltage NECL Mode Input Voltage VEE = 0 V VCC = 0 V 6 −6 V V Iout Output Current Continuous Surge 50 100 mA mA IBB VBB Sink/Source ± 0.5 mA TA Operating Temperature Range −40 to +85 °C Tstg Storage Temperature Range −65 to +150 °C JA Thermal Resistance (Junction−to−Ambient) 0 lfpm 500 lfpm 32 LQFP 32 LQFP 80 55 °C/W °C/W JC Thermal Resistance (Junction−to−Case) Standard Board 32 LQFP 12 to 17 °C/W Tsol Wave Solder <2 to 3 sec @ 248°C <2 to 3 sec @ 260°C 265 265 °C Pb Pb−Free Condition 2 VI VCC VI VEE Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Table 5. 10EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 2) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 95 119 143 98 122 146 100 125 150 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 3) 2165 2290 2415 2230 2355 2480 2290 2415 2540 mV VOL Output LOW Voltage (Note 3) 1365 1490 1615 1430 1555 1680 1490 1615 1740 mV VIH Input HIGH Voltage (Single−Ended) 2090 2415 2155 2480 2215 2540 mV VIL Input LOW Voltage (Single−Ended) 1365 1690 1460 1755 1490 1815 mV VBB Output Voltage Reference 1790 1990 1855 2055 1915 2115 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 4) 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 A IIL Input LOW Current 1890 2.0 150 0.5 1955 150 0.5 0.5 2015 A NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 2. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V. 3. All loading with 50 to VCC − 2.0 V. 4. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 4 MC10EP445, MC100EP445 Table 6. 10EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 5) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit IEE Power Supply Current (Note 6) 95 119 143 98 122 146 100 125 150 mA VOH Output HIGH Voltage (Note 7) 3865 3990 4115 3930 4055 4180 3990 4115 4240 mV VOL Output LOW Voltage (Note 7) 3065 3190 3315 3130 3255 3380 3190 3315 3440 mV VIH Input HIGH Voltage (Single−Ended) 3790 4115 3855 4180 3915 4240 mV VIL Input LOW Voltage (Single−Ended) 3065 3390 3130 3455 3190 3515 mV VBB Output Voltage Reference 3490 3690 3555 3755 3615 3815 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 8) 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 A IIL Input LOW Current 3590 2.0 3655 150 3715 150 0.5 0.5 A 0.5 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 5. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V. 6. Required 500 lfpm air flow when using +5 V power supply. For (VCC − VEE) >3.3 V, 5 to 10 in line with VEE required for maximum thermal protection at elevated temperatures. Recommend VCC−VEE operation at 3.3 V. 7. All loading with 50 to VCC − 2.0 V. 8. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 7. 10EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 9) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit IEE Power Supply Current (Note 10) 95 119 143 98 122 146 100 125 150 mA VOH Output HIGH Voltage (Note 11) −1135 −1010 −885 −1070 −945 −820 −1010 −885 −760 mV VOL Output LOW Voltage (Note 11) −1935 −1810 −1685 −1870 −1745 −1620 −1810 −1685 −1560 mV VIH Input HIGH Voltage (Single−Ended) −1210 −885 −1145 −820 −1085 −760 mV VIL Input LOW Voltage (Single−Ended) −1935 −1610 −1870 −1545 −1810 −1485 mV VBB Output Voltage Reference −1510 −1310 −1445 −1245 −1385 −1185 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 12) 0.0 V IIH Input HIGH Current 150 A IIL Input LOW Current −1410 VEE+2.0 0.0 VEE+2.0 150 0.5 −1345 0.0 VEE+2.0 150 0.5 −1285 0.5 A NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 9. Input and output parameters vary 1:1 with VCC. 10. Required 500 lfpm air flow when using −5 V power supply. For (VCC − VEE) >3.3 V, 5 to 10 in line with VEE required for maximum thermal protection at elevated temperatures. Recommend VCC−VEE operation at 3.3 V. 11. All loading with 50 to VCC − 2.0 V. 12. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 5 MC10EP445, MC100EP445 Table 8. 100EP DC CHARACTERISTICS, PECL VCC = 3.3 V, VEE = 0 V (Note 13) −40°C Symbol Characteristic 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit 95 119 143 98 122 146 100 125 150 mA IEE Power Supply Current VOH Output HIGH Voltage (Note 14) 2155 2280 2405 2155 2280 2405 2155 2280 2405 mV VOL Output LOW Voltage (Note 14) 1355 1480 1605 1355 1480 1605 1355 1480 1605 mV VIH Input HIGH Voltage (Single−Ended) 2075 2420 2075 2420 2075 2420 mV VIL Input LOW Voltage (Single−Ended) 1355 1675 1355 1675 1355 1675 mV VBB Output Voltage Reference 1775 1975 1775 1975 1775 1975 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 15) 3.3 2.0 3.3 2.0 3.3 V IIH Input HIGH Current 150 A IIL Input LOW Current 1875 2.0 1875 150 0.5 1875 150 0.5 A 0.5 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 13. Input and output parameters vary 1:1 with VCC. VEE can vary +0.3 V to −2.2 V. 14. All loading with 50 to VCC − 2.0 V. 15. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 9. 100EP DC CHARACTERISTICS, PECL VCC = 5.0 V, VEE = 0 V (Note 16) −40°C Symbol Characteristic Min Typ 25°C Max Min Typ 85°C Max Min Typ Max Unit IEE Power Supply Current (Note 17) 95 119 143 98 122 146 100 125 150 mA VOH Output HIGH Voltage (Note 18) 3855 3980 4105 3855 3980 4105 3855 3980 4105 mV VOL Output LOW Voltage (Note 18) 3055 3180 3305 3055 3180 3305 3055 3180 3305 mV VIH Input HIGH Voltage (Single−Ended) 3775 4120 3775 4120 3775 4120 mV VIL Input LOW Voltage (Single−Ended) 3055 3375 3055 3375 3055 3375 mV VBB Output Voltage Reference 3475 3675 3475 3675 3475 3675 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 19) 5.0 2.0 5.0 2.0 5.0 V IIH Input HIGH Current 150 A IIL Input LOW Current 3575 2.0 150 0.5 3575 150 0.5 0.5 3575 A NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 16. Input and output parameters vary 1:1 with VCC. VEE can vary +2.0 V to −0.5 V. 17. Required 500 lfpm air flow when using +5 V power supply. For (VCC − VEE) >3.3 V, 5 to 10 in line with VEE required for maximum thermal protection at elevated temperatures. Recommend VCC−VEE operation at 3.3 V. 18. All loading with 50 to VCC − 2.0 V. 19. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. http://onsemi.com 6 MC10EP445, MC100EP445 Table 10. 100EP DC CHARACTERISTICS, NECL VCC = 0 V, VEE = −5.5 V to −3.0 V (Note 20) −40°C 25°C 85°C Min Typ Max Min Typ Max Min Typ Max Unit IEE Power Supply Current (Note 21) 95 119 143 98 122 146 100 125 150 mA VOH Output HIGH Voltage (Note 22) −1145 −1020 −895 −1145 −1020 −895 −1145 −1020 −895 mV VOL Output LOW Voltage (Note 22) −1945 −1820 −1695 −1945 −1820 −1695 −1945 −1820 −1695 mV VIH Input HIGH Voltage (Single−Ended) −1225 −880 −1225 −880 −1225 −880 mV VIL Input LOW Voltage (Single−Ended) −1945 −1625 −1945 −1625 −1945 −1625 mV VBB Output Voltage Reference −1525 −1325 −1525 −1325 −1525 −1325 mV VIHCMR Input HIGH Voltage Common Mode Range (Differential Configuration) (Note 23) 0.0 V IIH Input HIGH Current 150 A IIL Input LOW Current Characteristic Symbol −1425 VEE + 2.0 0.0 −1425 VEE + 2.0 150 0.0 −1425 VEE + 2.0 150 0.5 0.5 A 0.5 NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 20. Input and output parameters vary 1:1 with VCC. 21. Required 500 lfpm air flow when using −5.0 V power supply. For (VCC − VEE) > 3.3 V, 5 to 10 in line with VEE required for maximum thermal protection at elevated temperatures. Recommend VCC − VEE operation at v 3.3 V. 22. All loading with 50 to VCC − 2.0 V. 23. VIHCMR min varies 1:1 with VEE, VIHCMR max varies 1:1 with VCC. The VIHCMR range is referenced to the most positive side of the differential input signal. Table 11. AC CHARACTERISTICS VCC = 0 V; VEE = −3.0 V to −5.5 V or VCC = 3.0 V to 5.5 V; VEE = 0 V (Note 24) −40°C Min Typ CKSEL = LOW CKSEL = HIGH 2.0 2.8 2.5 3.3 CLK to Q CLK TO PCLK 1280 1000 1475 1240 Characteristic Symbol 25°C Max Min Typ 2.0 2.8 2.5 3.3 1335 1050 1557 1310 85°C Max Min Typ 1.7 2.8 2.2 3.3 1450 1140 1663 1420 Max Unit fmax Maximum Input CLK Frequency (See Figure 12. Fmax/JITTER) tPLH, tPHL Propagation Delay to Output Differential ts Setup Time SINA, B+ TO CLK+ (Figure 4) CKEN+ TO CLK− (Figure 5) −400 100 −459 50 −420 100 −479 50 −440 100 −492 50 ps th Hold Time CLK+ TO SINA, B− (Figure 4) CLK− TO CKEN (Figure 5) 533 45 474 −35 550 45 490 −35 560 45 508 −35 ps tRR/tRR2 Reset Recovery (Figure 3) 350 180 350 180 350 180 ps tPW Minimum Pulse Width tJITTER RMS Random Clock Jitter @ 2.0 GHz CLK_SEL LOW @ 2.5 GHz CLK_SELF HIGH @ 3.0 GHz CLK_SEL HIGH RESET 1710 1490 400 1795 1580 400 GHz 1950 1710 400 ps ps ps 1.5 1.0 1.5 1.5 1.0 2.0 1.5 1.5 2.5 VPP Input Voltage Swing (Differential Configuration) (Note 25) 150 800 1200 150 800 1200 150 800 1200 mV tr tf Output Rise/Fall Times (20% − 80%) 100 100 180 180 400 250 100 100 200 200 400 300 125 125 230 230 425 325 ps Q/Q PCLK/PCLK NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit values are applied individually under normal operating conditions and not valid simultaneously. 24. Measured using a 750 mV source, 50% duty cycle clock source. All loading with 50 to VCC − 2.0 V. 25. VPP(min) is the minimum input swing for which AC parameters are guaranteed. http://onsemi.com 7 MC10EP445, MC100EP445 Reset tRR CLK CLK Figure 3. Reset Recovery CLK Data Setup Time + − ts Data Hold Time + − th Figure 4. Data Setup and Hold Time CLK CKEN Setup Time + − ts CKEN Hold Time − + th Figure 5. CKEN Setup and Hold Time http://onsemi.com 8 MC10EP445, MC100EP445 APPLICATION INFORMATION The two selectable serial data paths can be used for loop−back testing as well as the bit error testing. Upon power−up, the internal flip−flops will attain a random state. To synchronize multiple flip–flops in the device, the Reset (pin 1) must be asserted. The reset pin will disable the internal clock signal irrespective of the CKEN state (CKEN disables the internal clock circuitry). The device will grab the first stream of data after the falling edge of RESETÀ, followed by the falling edge of CLKÁ, on second rising edge of CLKÂ in either CKSEL modes. (See Figure 6) The MC10/100EP445 is an integrated 1:8 serial to parallel converter with two modes of operation selected by CKSEL (Pin 7). CKSEL HIGH mode only latches data on the rising edge of the input CLK and CKSEL LOW mode latches data on both the rising and falling edge of the input CLK. CKSEL LOW is the open default state. Either of the two differential input serial data path provided for this device, SINA and SINB, can be chosen with the SINSEL pin (pin 25). SINA is the default input path when SINSEL pin is left floating. Because of internal pull−downs on the input pins, all input pins will default to logic low when left open. RESET (Asynchronous Reset) RESET (Synchronous ENABLE) Á CLK À RESET PCLK Figure 6. Reset Timing Diagram http://onsemi.com 9 Â MC10EP445, MC100EP445 For CKSEL LOW operation, the data is latched on both the rising edge and the falling edge of the clock and the time from when the serial data is latchedÀ to when the data is seen on the parallel outputÁ is 6 clock cycles (see Figure 7). Number of Clock Cycles from Data Latch to Q 1 2 3 4 5 6 À CLK SINA D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 RESET CKEN CKSEL PCLK Á Q0 D0 D8 D16 Q1 D1 D9 D17 Q2 D2 D10 D18 Q3 D3 D11 D19 Q4 D4 D12 D20 Q5 D5 D13 D21 Q6 D6 D14 D22 Q7 D7 D15 D23 Figure 7. Timing Diagram A. 1:8 Serial to Parallel Conversion with CKSEL LOW http://onsemi.com 10 MC10EP445, MC100EP445 Similarly, for CKSEL HIGH operation, the data is latched only on the rising edge of the clock and the time from when the serial data is latchedÀ to when the data is seen on the parallel outputÁ is 12 clock cycles (see Figure 8). Number of Clock Cycles from Data Latch to Q 2 3 4 5 6 7 8 9 10 1 11 12 À CLK SINA D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 RESET CKEN CKSEL PCLK Á Q0 D0 Q1 D1 Q2 D2 Q3 D3 Q4 D4 Q5 D5 Q6 D6 Q7 D7 Figure 8. Timing Diagram A. 1:8 Serial to Parallel Conversion with CKSEL HIGH http://onsemi.com 11 MC10EP445, MC100EP445 clock cycles shifts the start bit for conversion from Qn to Qn−1. The bit is swallowed following the two clock cycle pulse width of SYNCÀ on the next triggering edge of clockÁ (either on the rising or the falling edge of the clock). Each additional shift requires an additional pulse to be applied to the SYNC pin. (See Figure 9) To allow the user to synchronize the output byte data correctly, the start bit for conversion can be moved using the SYNC input pin (pin 2). Asynchronously asserting the SYNC pin will force the internal clock to swallow a clock pulse, effectively shifting a bit from the Qn to the Qn−1 output as shown in Figure 9 and Figure 10. For CKSEL LOW, a single pulse applied asynchronously for two consecutive 2 Clock Cycles for SYNC 1 2 Á Next Triggering Edge of Clock Bit D8 is Swallowed CLK SINA D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 D16 D17 D18 D19 D20 D21 D22 D23 D24 CKSEL PCLK SYNC À Q0 D0 D9 D17 Q1 D1 D10 D18 Q2 D2 D11 D19 Q3 D3 D12 D20 Q4 D4 D13 D21 Q5 D5 D14 D22 Q6 D6 D15 D23 Q7 D7 D16 D24 Figure 9. Timing Diagram A. 1:8 Serial to Parallel Conversion with SYNC Pulse at CKSEL LOW http://onsemi.com 12 MC10EP445, MC100EP445 For CKSEL HIGH, a single pulse applied asynchronously for three consecutive clock cycles shifts the start bit for conversion from Qn to Qn−1. The bit is swallowed following the three clock cycle pulse width of SYNCÀ on the next 3 Clock Cycles for Sync 1 2 3 triggering edge of clockÁ (on the rising edge of the clock only). Each additional shift requires an additional pulse to be applied to the SYNC pin. (See Figure 10) Next Triggering Edge of Clock Á Bit D8 is Swallowed CLK SINA SYNC D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 À PCLK Q0 D0 Q1 D1 Q2 D2 Q3 D3 Q4 D4 Q5 D5 Q6 D6 Q7 D7 Figure 10. Timing Diagram A. 1:8 Serial to Parallel Conversion with SYNC Pulse at CKSEL HIGH http://onsemi.com 13 MC10EP445, MC100EP445 edge of CLK will suspend all activities. The first data bit will clock on the rising edge, since the falling edge of CKEN followed by the falling edge of the incoming clock triggers the enabling of the internal process. (See Figure 11) The synchronous CKEN (pin 3) applied with at least one clock cycle pulse length will disable the internal clock signal. The synchronous CKEN will suspend all of the device activities and prevent runt pulses from being generated. The rising edge of CKEN followed by the falling Internal Clock Disabled Internal Clock Enabled CLK CKEN PCLK CKSEL Figure 11. Timing Diagram with CKEN with CKSEL HIGH conditions, the unused differential input is connected to VBB as a switching reference voltage. VBB may also rebias AC coupled inputs. When used, decouple VBB and VCC via a 0.01 F capacitor, which will limit the current sourcing or sinking to 0.5mA. When not used, VBB should be left open. Also, both outputs of the differential pair must be terminated (50 to VTT = VCC – 2 V) even if only one output is used. The differential PCLK output (pins 22 and 23) is a word framer and can help the user to synchronize the parallel data outputs. During CKSEL LOW operation, the PCLK will provide a divide by 4−clock frequency, which frames the serial data in period of PCLK output. Likewise during CKSEL HIGH operation, the PCLK will provide a divide by 8−clock frequency. The VBB pin, an internally generated voltage supply, is available to this device only. For single–ended input http://onsemi.com 14 MC10EP445, MC100EP445 1000 VOUTpp (mV) 900 9 800 8 700 7 CKSEL LOW 600 6 500 5 400 4 300 3 200 ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ ÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉÉ (JITTER) 100 0 0 500 1000 1500 2000 2500 3000 ÉÉ ÉÉ 2 1 3500 INPUT CLK FREQUENCY (MHz) Figure 12. Fmax/Jitter Q Zo = 50 D Receiver Device Driver Device Q Zo = 50 D 50 50 VTT VTT = VCC − 3.0 V Figure 13. Typical Termination for Output Driver and Device Evaluation (See Application Note AND8020/D − Termination of ECL Logic Devices.) http://onsemi.com 15 JITTEROUT ps (RMS) 10 CKSEL HIGH MC10EP445, MC100EP445 ORDERING INFORMATION Package Shipping† MC10EP445FA LQFP−32 250 Units / Tray MC10EP445FAG LQFP−32 (Pb−Free) 250 Units / Tray MC10EP445FAR2 LQFP−32 2000 / Tape & Reel MC10EP445FAR2G LQFP−32 (Pb−Free) 2000 / Tape & Reel MC100EP445FA LQFP−32 250 Units / Tray MC100EP445FAG LQFP−32 (Pb−Free) 250 Units / Tray MC100EP445FAR2 LQFP−32 2000 / Tape & Reel MC100EP445FAR2G LQFP−32 (Pb−Free) 2000 / Tape & Reel Device †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. Resource Reference of Application Notes AN1405/D − ECL Clock Distribution Techniques AN1406/D − Designing with PECL (ECL at +5.0 V) AN1503/D − ECLinPSt I/O SPiCE Modeling Kit AN1504/D − Metastability and the ECLinPS Family AN1568/D − Interfacing Between LVDS and ECL AN1642/D − The ECL Translator Guide AND8001/D − Odd Number Counters Design AND8002/D − Marking and Date Codes AND8020/D − Termination of ECL Logic Devices AND8066/D − Interfacing with ECLinPS AND8090/D − AC Characteristics of ECL Devices http://onsemi.com 16 MC10EP445, MC100EP445 PACKAGE DIMENSIONS A 32 A1 −T−, −U−, −Z− 32 LEAD LQFP CASE 873A−02 ISSUE B 4X 25 0.20 (0.008) AB T−U Z 1 AE −U− −T− B P V 17 8 BASE METAL DETAIL Y V1 ÉÉ ÉÉ ÉÉ −Z− 9 S1 4X 0.20 (0.008) AC T−U Z F S 8X M_ J R D DETAIL AD G SECTION AE−AE −AB− C E −AC− H W K X DETAIL AD NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DATUM PLANE −AB− IS LOCATED AT BOTTOM OF LEAD AND IS COINCIDENT WITH THE LEAD WHERE THE LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF THE PARTING LINE. 4. DATUMS −T−, −U−, AND −Z− TO BE DETERMINED AT DATUM PLANE −AB−. 5. DIMENSIONS S AND V TO BE DETERMINED AT SEATING PLANE −AC−. 6. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. ALLOWABLE PROTRUSION IS 0.250 (0.010) PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD MISMATCH AND ARE DETERMINED AT DATUM PLANE −AB−. 7. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. DAMBAR PROTRUSION SHALL NOT CAUSE THE D DIMENSION TO EXCEED 0.520 (0.020). 8. MINIMUM SOLDER PLATE THICKNESS SHALL BE 0.0076 (0.0003). 9. EXACT SHAPE OF EACH CORNER MAY VARY FROM DEPICTION. DIM A A1 B B1 C D E F G H J K M N P Q R S S1 V V1 W X http://onsemi.com 17 MILLIMETERS MIN MAX 7.000 BSC 3.500 BSC 7.000 BSC 3.500 BSC 1.400 1.600 0.300 0.450 1.350 1.450 0.300 0.400 0.800 BSC 0.050 0.150 0.090 0.200 0.500 0.700 _ 12 REF 0.090 0.160 0.400 BSC 1_ 5_ 0.150 0.250 9.000 BSC 4.500 BSC 9.000 BSC 4.500 BSC 0.200 REF 1.000 REF INCHES MIN MAX 0.276 BSC 0.138 BSC 0.276 BSC 0.138 BSC 0.055 0.063 0.012 0.018 0.053 0.057 0.012 0.016 0.031 BSC 0.002 0.006 0.004 0.008 0.020 0.028 _ 12 REF 0.004 0.006 0.016 BSC 1_ 5_ 0.006 0.010 0.354 BSC 0.177 BSC 0.354 BSC 0.177 BSC 0.008 REF 0.039 REF Q_ 0.250 (0.010) 0.10 (0.004) AC GAUGE PLANE SEATING PLANE M N 9 0.20 (0.008) DETAIL Y AC T−U Z AE B1 MC10EP445, MC100EP445 ECLinPS is a trademark of Semiconductor Components INdustries, LLC (SCILLC). ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 18 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative MC10EP445/D