2SD2670 Transistors Low frequency amplifier 2SD2670 zExternal dimensions (Unit : mm) zApplication Low frequency amplifier Driver TSMT3 1.0MAX zFeatures 1) A collector current is large. 2) VCE(sat) : max.250mV At lc=1.5A / lB=30mA 2.9 0.85 0.4 0.7 1.6 2.8 (3) 0.3~0.6 0~0.1 (2) (1) 0.95 0.95 1.9 0.16 (1) Base (2) Emitter Each lead has same dimensions (3) Collector zAbsolute maximum ratings (Ta=25°C) Parameter Collector-base voltage Collector-emitter voltage Emitter-base voltage Collector current Symbol VCBO VCEO VEBO IC ICP PC Power siddipation Junction temperature Range of storage temperature Tj Tstg Limits 15 12 6 3 6 500 1 ∗2 150 −55 to +150 Unit V V V A A∗1 mW W °C °C ∗1 Single pulse, Pw=1ms ∗2 Mounted on a 25×25× t 0.8mm Ceramic substrate zElectrical characteristics (Ta=25°C) Parameter Collector-base breakdown voltage Collector-emitter breakdown voltage Emitter-base breakdown voltage Collector cutoff current Emitter cutoff current Collector-emitter saturation voltage DC current gain Transition frequency Collector output capacitance Symbol BVCBO BVCEO BVEBO ICBO IEBO VCE(sat) hFE fT Cob Min. 15 12 6 − − − 270 − − Typ. − − − − − 120 − 360 30 Max. − − − 100 100 250 680 − − Unit V V V nA nA mV − MHz pF Conditions IC=10µA IC=1mA IE=10µA VCB=15V VEB=6V IC=1.5A, IB=30mA VCE=2V, IC=500mA ∗ VCE=2V, IE=−500mA, f=100MHz ∗ VCB=10V, IE=0A, f=1MHz ∗ Pulse Rev.C 1/2 2SD2670 Transistors zPackaging specifications package Type Taping TL Code 3000 Basic ordering unit (pieces) 2SD2670 1000 10 COLLECTOR TO EMITTER SATURATION VOLTAGE : VCE(sat) (V) VCE=−2V Pulsed Ta=25 C Ta=40 C 100 10 0.001 0.01 0.1 1 Ta=−45 C Ta=100 C 0.1 0.01 0.001 10 Ta=25 C 1 0.01 0.1 1 Ta=100 C Ta=25 C 1 Ta=−45 C 0.1 0.01 0.001 10 BASE TO EMITTER CURRENT : VBE (V) Fig.4 Grounded emitter propagation characteristics TRANSITION FREQUENCY : fT (MHz) IC/IB=20/1 Pulsed 100 0.1 1 EMITTER CURRENT : IE (A) Fig.5 Gain bandwidth product vs. emitter current IC/IB=50/1 IC/IB=10/1 IC/IB=20/1 0.1 0.001 0.01 0.1 1 10 Fig.3 Base-emitter saturation voltage vs.collector current 1000 Ta=25 C VCE=−2V f= 100MHz 10 0.01 Ta=25 C Pulsed COLLECTOR CURRENT : IC (A) 1000 10 1 1 10 Fig.2 Collector-emitter saturation voltage vs. collector current Fig.1 DC current gain vs. collector current 0.1 10 COLLECTOR CURRENT : IC (A) COLLECTOR CURRENT : IC (A) COLLECTOR CURRENT :IC (A) IC/IB=20/1 VCE=2V Pulsed COLLECTOR OUTPUT CAPACITANCE : Cob (pF) EMITTER INPUT CAPACITANCE : Cib (pF) DC CURRENT GAIN : hFE Ta=100 C BASE SATURATION VOLTAGE : VBE(sat) (V) zElectrical characteristic curves 10 IC=0A f=1MHz Ta=25 C Cib 100 Cob 10 0.001 0.01 0.1 1 10 100 EMITTER TO BASE VOLTAGE : VEB(V) COLLECTOR TO BASE VOLTAGE : VCB(V) Fig.6 Collector output capacitance vs. collector-base voltage Emitter input capacitance vs. emitter-base voltage Rev.C 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1