Micro Linear ML65F16245CT 16-bit bidirectional transceiver with 3-state output Datasheet

June 1998
PRELIMINARY
ML65F16245*
16-Bit Bidirectional Transceiver with 3-State Outputs
GENERAL DESCRIPTION
FEATURES
The ML65F16245 is a BiCMOS, non-inverting 16-bit
transceiver with 3-state outputs. This device was
specifically designed for high speed bus applications. Its
16 channels support propagation delay of 2ns maximum,
and fast output enable and disable times of 5ns or less to
minimize datapath delay.
■
Low propagation delays — 2ns maximum for 3.3V,
2.5ns maximum for 2.7V
■
Fast output enable/disable times of 5ns maximum
■
FastBus Charge current to minimize the bus settling
time during active capacitive loading
■
2.7V to 3.6V a VCC supply operation; LV-TTL
compatible input and output levels with 3-state
capability
■
Industry standard pinout compatible to FCT, ALV, LCX,
LVT, and other low voltage logic families
■
ESD protection exceeds 2000V
■
Full output swing for increased noise margin
■
Undershoot and overshoot protection to 400mV
typically
■
Low ground bounce design
This device is designed to minimize undershoot,
overshoot, and ground bounce to decrease noise delays.
These transceivers implement a unique digital and analog
implementation to eliminate the delays and noise
inherent in traditional digital designs. The device offers a
new method for quickly charging up a bus load capacitor
to minimize bus settling times, or FastBus™ Charge.
FastBus Charge is a transition current, (specified as
IDYNAMIC) that injects between 60 to 200mA (depending
on output load) of current during the rise time and fall
time. This current is used to reduce the amount of time it
takes to charge up a heavily-capacitive loaded bus,
effectively reducing the bus settling times, and
improving data/clock margins in tight timing budgets.
Micro Linear’s solution is intended for applications for
critical bus timing designs that include minimizing
device propagation delay, bus settling time, and time
delays due to noise. Applications include; high speed
memory arrays, bus or backplane isolation, bus to bus
bridging, and sub-2ns propagation delay schemes.
The ML65F16245 follows the pinout and functionality of
the industry standard 2.7V to 3.6V-logic families.
*This Part Is End Of Life As Of August 1, 2000
BLOCK DIAGRAM
DIR
VCC
OEAB
Bi
Ai
Bi
OE
OEBA
i=0 to 15
GND
1
ML65F16245
PIN CONFIGURATION
ML65F16245
48-Pin SSOP (R48)
48-Pin TSSOP (T48)
1DIR
1
48
1OE
1B0
2
47
1A0
1B1
3
46
1A1
GND
4
45
GND
1B2
5
44
1A2
1B3
6
43
1A3
VCC
7
42
VCC
1B4
8
41
1A4
1B5
9
40
1A5
GND
10
39
GND
1B6
11
38
1A6
1B7
12
37
1A7
2B0
13
36
2A0
2B1
14
35
2A1
GND
15
34
GND
2B2
16
33
2A2
2B3
17
32
2A3
VCC
18
31
VCC
2B4
19
30
2A4
2B5
20
29
2A5
GND
21
28
GND
2B6
22
27
2A6
2B7
23
26
2A7
2DIR
24
25
2OE
TOP VIEW
FUNCTION TABLE
(Each 8-bit section)
OE
DIR
Ai
Bi
FUNCTION
H
X
Z
Z
Disable
L
L
Output
Input
Bus B to Bus A
L
H
Input
Output
Bus A to Bus B
L = Logic Low, H = Logic High, X = Don’t Care, Z = High Impedance
i = 0 to 7
2
ML65F16245
PIN DESCRIPTION
PIN
NAME
FUNCTION
1
1DIR
Direction Select
2
1B0
Data Bus 1B
3
1B1
Data Bus 1B
4
GND
Signal Ground
5
1B2
Data Bus 1B
6
1B3
Data Bus 1B
7
VCC
2.7V to 3.6V Supply
8
1B4
Data Bus 1B
9
1B5
Data Bus 1B
10
GND
Signal Ground
11
1B6
Data Bus 1B
12
1B7
Data Bus 1B
13
2B0
Data Bus 2B
14
2B1
Data Bus 2B
15
GND
Signal Ground
16
2B2
Data Bus 2B
17
2B3
Data Bus 2B
18
VCC
2.7V to 3.6V Supply
19
2B4
Data Bus 2B
20
2B5
Data Bus 2B
21
GND
Signal Ground
22
2B6
Data Bus 2B
23
2B7
Data Bus 2B
24
2DIR
Direction Select
PIN
NAME
FUNCTION
25
2OE
Output Enable
26
2A7
Data Bus 2A
27
2A6
Data Bus 2A
28
GND
Signal Ground
29
2A5
Data Bus 2A
30
2A4
Data Bus 2A
31
VCC
2.7V to 3.6V Supply
32
2A3
Data Bus 2A
33
2A2
Data Bus 2A
34
GND
Signal Ground
35
2A1
Data Bus 2A
36
2A0
Data Bus 2A
37
1A7
Data Bus 1A
38
1A6
Data Bus 1A
39
GND
Signal Ground
40
1A5
Data Bus 1A
41
1A4
Data Bus 1A
42
VCC
2.7V to 3.6V Supply
43
1A3
Data Bus 1A
44
1A2
Data Bus 1A
45
GND
Signal Ground
46
1A1
Data Bus 1A
47
1A0
Data Bus 1A
48
1OE
Output Enable
3
ML65F16245
ABSOLUTE MAXIMUM RATINGS
Absolute maximum ratings are those values beyond which
the device could be permanently damaged. Absolute
maximum ratings are stress ratings only and functional
device operation is not implied.
Storage Temperature Range ..................... –65°C to 150°C
Junction Temperature .............................................. 150°C
Lead Temperature (Soldering, 10sec) ...................... 150°C
Thermal Impedance (qJA) ..................................... 76°C/W
VCC ............................................................................. 7V
DC Input Voltage ............................. –0.3V to VCC + 0.3V
AC Input Voltage (PW < 20ns) ................................ –3.0V
DC Output Voltage ...................................–0.3V to 7VDC
Output Current, Source or Sink ............................. 180mA
OPERATING CONDITIONS
Temperature Range ....................................... 0°C to 70°C
VIN Operating Range ...................................2.7V to 3.6V
ELECTRICAL CHARACTERISTICS
Unless otherwise specified, VIN = 3.3V, TA = Operating Temperature Range (Note 1).
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
3.3V
1.35
1.7
2
ns
2.7V
1.25
1.9
2.5
ns
3.3V
5
ns
2.7V
6
ns
3.3V
5
ns
2.7V
6
ns
3.3V
5
ns
2.7V
6
ns
3.3V
5
ns
2.7V
6
ns
300
ps
AC ELECTRICAL CHARACTERISTICS (CLOAD = 50pF)
tPHL, tPLH
tOE
Propagation Delay
Output Enable Time
Ai to/from Bi
OE to Ai/Bi
DIR to Ai/Bi
tOD
Output Disable Time
OE to Ai/Bi
DIR to Ai/Bi
TOS
Output-to-Output Skew
CIN
Input Capacitance
8
pF
DC ELECTRICAL CHARACTERISTICS (CLOAD = 50pF, RLOAD = Open)
VIH
Input High Voltage
Logic high
VIL
Input Low Voltage
Logic low
0.8
V
IIH
Input High Current
Per pin, VIN = 3V
300
µA
IIL
Input Low Current
Per pin, VIN = 0V
300
µA
IHI-Z
Three-State Output Current
VCC = 3.6V, 0 < VIN < VCC
5
µA
V IC
Input Clamp Voltage
VCC = 3.6V, IIN = 18mA
–0.2
V
I DYNAMIC Dynamic Transition Current
(FastBus Charge)
VOH
2.0
–0.7
Low to high transitions
80
mA
High to low transitions
80
mA
Output High Voltage
VCC = 3.6V
2.4
3.4
V
VCC = 2.7V
2.25
2.35
V
VOL
Output Low Voltage
VCC = 3.6V and 2.7V
0.6
V
I CC
Quiescent Power Supply Current
VCC = 3.6V, f = 0Hz,
inputs = VCC or 0V
3
µA
Note 1: Limits are guaranteed by 100% testing, sampling, or correlation with worst-case test conditions.
4
V
ML65F16245
100
0
–20
80
–40
IOH (mA)
IOL (mA)
–60
60
40
–80
–100
–120
–140
20
–160
–180
0
0
0.4
0.8
1.2
1.6
–200
1.8
2
2.0
2.2
2.4
VOL (V)
3.0
3.2
3.4
3.6
Figure 1b. Typical VOH vs. IOH for 3.3V VCC.
One Buffer Output
3.0
3.0
2.5
2.5
VCC = 2.7V
VCC = 2.7V
2.0
tPLH (ns)
2.0
tPHL (ns)
2.8
VOH (V)
Figure 1a. Typical VOL vs. IOL for 3.3V VCC.
One Buffer Output
VCC = 3.3V
1.5
1.0
0.5
0.5
25
0
0
75
50
VCC = 3.3V
1.5
1.0
0
2.6
25
0
LOAD CAPACITANCE (pF)
75
50
LOAD CAPACITANCE (pF)
Figure 2a. Propagation Delay vs. Load Capacitance:
3.3V, 50MHZ
Figure 2b. Propagation Delay vs. Load Capacitance:
2.7V, 50MHZ
60
60
50
50
75pF
75pF
40
ICC (mA)
ICC (mA)
40
30
50pF
20
30pF
10
0
0
20
40
60
80
100
FREQUENCY (MHz)
Figure 3a. ICC vs. Frequency: VCC = VIN = 3.3V.
One Buffer Output
30
50pF
20
30pF
10
0
0
20
40
60
80
100
FREQUENCY (MHz)
Figure 3b. ICC vs. Frequency: VCC = VIN = 2.7V.
One Buffer Output
5
ML65F16245
FUNCTIONAL DESCRIPTION
1OEAB
1DIR
1A0
1B0
1OE
2OEAB
2DIR
2B0
2OE
1OEBA
2A0
2OEBA
1B1
1A1
2B1
2A1
1B2
1A2
2B2
2A2
1B3
1A3
2B3
2A3
1B4
1A4
2B4
2A4
1B5
1A5
2B5
2A5
1B6
1A6
2B6
2A6
1B7
1A7
2B7
2A7
Figure 4. Logic Diagram
1A0
1A1
1A2
1A3
1A4
1A5
1A6
1A7
2A0
2A1
2A3
2A4
2A5
2A6
2A7
1OE
2OE
1DIR
2DIR
1B0
1B1
1B2
1B3
1B4
1B5
1B6
1B7
2B0
2B1
Figure 5. Logic Symbol
6
2A2
2B2
2B3
2B4
2B5
2B6
2B7
ML65F16245
ARCHITECTURAL DESCRIPTION
The basic architecture of the ML65F16245 is shown in
Figure 6. In this circuit, there are two paths to the output.
One path sources current to the load capacitance where
the signal is asserted, and the other path sinks current
from the output when the signal is negated.
The ML65F16245 is a 16-bit (dual-octal) non-inverting bus
transceiver with 3-state outputs designed for 2.7V to 3.6V
VCC operation. This device is designed for asynchronous
communication between data buses. The ML65F16245
can be used as two 8-bit transceivers or as one 16-bit
transceiver and can be designated as Port-A bus and Port-B
bus. The Direction and Output Enable controls are
designed to operate these configurations. The direction
control pin (iDIR) controls the direction of the data flow.
The output enable pin (1OE, 2OE) overrides the direction
control and disables both ports.
The assertion path is the Darlington pair consisting of
transistors Q1 and Q2. The effect of transistor Q1 is to
increase the current gain through the stage from input to
output, to increase the input resistance and to reduce
input capacitance. During the transition state (the input
from low-to-high) the output transistor Q2 sources large
amount of current to quickly charge up a highly
capacitive load which in effect reduces the bus settling
time. This current is specified as IDYNAMIC.
Until now, these transceivers were typically implemented
in CMOS logic and made to be TTL compatible by sizing
the input devices appropriately. In order to buffer large
capacitances with CMOS logic, it is necessary to cascade
an even number of inverters, each successive inverter
larger than the preceding, eventually leading to an
inverter that will drive the required load capacitance at
the required frequency. Each inverter stage represents an
additional delay in the gating process because in order for
a single gate to switch, the input must slew more than
half of the supply voltage. The best of these 16-bit CMOS
buffers has managed to drive 50pF load capacitance with
a delay of 3ns.
The negation path is also the Darlington pair consisting of
transistor Q3 and transistor Q4. With M1 connecting to
the input of the Darlington pair, Transistor Q4 then sinks a
large amount of current during the input transition from
high-to-low.
Inverter X2 is a helpful buffer that not only drives the
output toward the upper rail but also pulls the output to
the lower rail.
There are a number of MOSFETs not shown in Figure 6.
These MOSFETs are used to 3-state the buffers.
Micro Linear has produced a 16-bit transceiver with a
delay less than 2ns (at 3.3V) by using a unique circuit
architecture that does not require cascade logic gates.
VCC
OE
Q1
Q2
X1
X2
IN
OUT
M1
Q3
Q4
Figure 6. One Buffer Cell of the ML65F16245
7
ML65F16245
CIRCUITS AND WAVE FORMS
VCC = 3V
ML65F16245
DUT
1.5V
INPUT
VIN
0V
3V
tPLH
VOUT
50pF
1.5V
IOUT
OUTPUT
0V
tRISE AND tFALL INPUT = 2ns
Figure 7. Test Circuits for All Outputs
ENABLE
Figure 8. Propagation Delay
DISABLE
VCC = 3V
CONTROL
INPUT
tPHL
INPUT
1.5V
1.5V
tOE
tOD
3V
OUTPUT1
OUTPUT
LOW
1.5V
VOL + 0.3V
VOL
tOE
VOH
VOH – 0.3V
OUTPUT
HIGH
OUTPUTi
i = 1 to 16
1.5V
0V
tOD
Figure 9. Enable and Disable Times
8
tOS
Figure 10. Output Skew
ML65F16245
PHYSICAL DIMENSIONS
inches (millimeters)
Package: R48
48-Pin SSOP
0.620 - 0.630
(15.75 - 16.00)
48
0.291 - 0.301 0.402 - 0.410
(7.39 - 7.65) (10.21 - 10.41)
PIN 1 ID
1
0.015 - 0.025
(0.38 - 0.64)
(4 PLACES)
0.025 BSC
(0.63 BSC)
0.094 - 0.110
(2.39 - 2.79)
0º - 8º
0.088 - 0.092
(2.24 - 2.34)
0.006 - 0.014
(0.15 - 0.36)
SEATING PLANE
0.024 - 0.040
(0.61 - 1.02)
0.008 - 0.016
(0.20 - 0.41)
0.005 - 0.010
(0.13 - 0.26)
Package: T48
48-Pin TSSOP
0.487 - 0.497
(12.37 - 12.63)
0.236 - 0.244
(6.00 - 6.20)
0.319 BSC
(8.1 BSC)
PIN 1 ID
0.020 BSC
(0.50 BSC)
0.047 MAX
(1.20 MAX)
0º - 8º
0.031 - 0.039
(0.80 - 1.00)
0.007 - 0.011
(0.17 - 0.27)
SEATING PLANE
0.002 - 0.006
(0.05 - 0.15)
0.020 - 0.028
(0.50 - 0.70)
0.004 - 0.008
(0.10 - 0.20)
9
ML65F16245
ORDERING INFORMATION
© Micro Linear 1998.
PART NUMBER
TEMPERATURE RANGE
PACKAGE
ML65F16245CR (Obsolete)
0°C to 70°C
48-Pin SSOP (R48)
ML65F16245CT (EOL)
0°C to 70°C
48-Pin TSSOP (T48)
is a registered trademark of Micro Linear Corporation. All other trademarks are the property of their respective owners.
Products described herein may be covered by one or more of the following U.S. patents: 4,897,611; 4,964,026; 5,027,116; 5,281,862; 5,283,483; 5,418,502;
5,508,570; 5,510,727; 5,523,940; 5,546,017; 5,559,470; 5,565,761; 5,592,128; 5,594,376; 5,652,479; 5,661,427; 5,663,874; 5,672,959; 5,689,167; 5,714,897;
5,717,798; 5,742,151; 5,747,977; 5,754,012; 5,757,174; 5,767,653;. Japan: 2,598,946; 2,619,299; 2,704,176. Other patents are pending.
Micro Linear reserves the right to make changes to any product herein to improve reliability, function or design. Micro Linear does not assume any liability
arising out of the application or use of any product described herein, neither does it convey any license under its patent right nor the rights of others. The circuits
contained in this data sheet are offered as possible applications only. Micro Linear makes no warranties or representations as to whether the illustrated circuits
infringe any intellectual property rights of others, and will accept no responsibility or liability for use of any application herein. The customer is urged to consult
with appropriate legal counsel before deciding on a particular application.
10
2092 Concourse Drive
San Jose, CA 95131
Tel: (408) 433-5200
Fax: (408) 432-0295
www.microlinear.com
DS65F16245-01
Similar pages