Single Slot SMT Connectors For Card-Bus Based PC Cards IC11S Series PC Card Standard Compliant Reduced height : 5.6mm high ■Features Wide variety of options 1. PC Card Standard compliant: (1)Board Mounting ➀Standard type ➁Reverse type • Grounding is required to meet the high speed signal requrements of the PC card standard. Grounding reliability is achieved with a grounding plate and 8 grounding contacts. • Type 1, type 2 and type 3 cards are covered. • Terminals for ground clipping are provided. 2. Space saving Smaller size reduces occupied area on PC boards as compared to previous products. 3. Reduced Height: Connector height is minimized to 5.6mm, making possible thinner product designs. 4. Eject mechanism with high-level functionality Hirose Electric's original ejection mechanism provides an higher degree of card ejection over existing products. This improves the operational qualities of card removal. (Patents pending) 5. Wide Variety of Options Available • Standard type mounts to the top of the PC board and reverse type mounts on the underside of the board • Three types of eject buttons; rigid, flexible and POP-UP.All types can be installed on the right or left side of the ejector. • Available with standoff to utilize space under the connector for mounting other parts. 6. Light-weight Weight of 12.7g for normal button type helps achieve the reduced weight required in today’s products. A2 (2)Types of eject button ➀Rigid button ➁Foldering button ➂Pop-up button (3)Position of eject buttons ➀Right ➁Left (4)Standoffs ➀None ➁2.2mm ■Product Specifications Ratings Operating temperature -55ç to +85ç(Note.1) Storage temperature -40ç to +70ç(Note.2) Current rating 0.5A Voltage rating 125V AC Item Operating humidity Relativehumidity 95% max. Storage humidity (With no dew-fall) Specification 40% to 70%(Note.2) Conditions 1.Insulation resistance 1000M ohms min. 2.Withstanding voltage No flashover or insulation breakdown. 3.Contact resistance 60m ohms max. (initial value) 500V DC 500V AC 1mA 4.Vibration Frequency: 10 to 2000 Hz, full amplitude of 1.52 mm or acceleration of 147 m/s2(peak), 4 hours in each of the 3 directions. No electrical discontinuity of 100ns or more 5.Humidity (Steady state) Insulation resistance: 100M ohms min. 96 hours at temperature of 40ç and humidity of 90% to 95% 6.Temperature cycle (-55ç:30min./+5ç to 35ç:MAX 5min/85ç:30min/+5 -35ç:MAX 5min.) 5 cycles Insulation resistance: 100M ohms min. 7.Durability Variations from initial contact resistance: 20m (Insertion/withdrawal) ohms max. No deformation of components affecting performance. 8.Resistance to Soldering heat 10000 cycles at 400 to 600 cycles per hour Reflow: At the recommended temperature profile Manual soldering: 300ç for 3 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. ■Material SMT unit Parts Material Insulator PPS Finish Black Remarks UL94V-0 Card connected section Brass Contact section: gold plating Lead section: solder plating Ground plate Phosphor bronze Contact section: gold plating Lead section: solder plating ---------- ---------- ---------- Contact Eject metal fittings Stainless steel ---------- Guide unit Item Material Finish Remarks Guide plate Stainless steel ---------- ---------- Push rod Stainless steel ---------- ---------- Rigid button type resin section PBT Color : Black UL94V-0 resin section PBT Color : Black UL94V-0 spring Stainless steel ---------- ---------- spring pin Stainless steel resin section PBT frame metal spring pin Foldering button type Eject Button POP-UP type Nut ---------- ---------- Color : Black UL94V-0 Stainless steel ---------- ---------- Steel ---------- ---------- Brass Nickel plating ---------- Steel ---------- M2X0.4 A3 ■Ordering Information SMT Unit IC11S A - 68 PLR - 1.27SF - EJ R 1 2 3 4 5 6 7 1 Series name : IC11S 5 1.27SF : 1.27mm pitch SMT connector 2 Standoff type Blank : none A : 2.2mm 6 With ejector EJ : with ejector 7 Eject button positions R : right L : left 3 Number of contacts : 68 4 Board Mounting Type: PL : standard type PLR : reverse type Guide Unit IC11S A - BUR - FEJ R 8 8 Series name : IC11S 9 Standoff type Blank: none A : 2.2mm 10 Board Mounting Type BD : standard type BUR : reverse type 9 10 11 12 11 Eject button type EJ : rigid button FEJ : Foldering button PEJ : POP-UP button 12 Eject button positions R : right L : left (Note.) IC11S Series will be used in combination of SMT unit with guide unit. When using, please select the same type for the following items. Please note that other combinations cannot be used. • Series name • Standoff • Board-installed type • Eject button positions A4 (1⇔8) (2⇔9) ( 4 ⇔ 10 ) ( 7 ⇔ 12 ) ■Standard Right rigid button type 34.4 MAX 3 59 42.545 P= 0.635 SMT unit ( 1 ) No.1 No.35 No.2 GND No.34 eject metal fittings movable range GND C 20.5 7.4 10MAX 7MAX No.36 No.68 72 85.6: in card insertion 51.5 PUSH PUSH A 6 guide unit ( 2 ) ( 34.9) none 2.2mm No.36 No.68 (27.6) 4.8 No.34 A B No.35 Standoff type No.2 stroke:9 54.9 3 No.1 59.5 (18.6) 5.9 3 ➀SMT unit ➁Guide unit CL No. Part Number CL No. A (mm) B (mm) IC11S-68PL-1.27SF-EJR 640-1007-3 IC11SA-68PL-1.27SF-EJR 640-1009-9 IC11S-BD-EJR IC11SA-BD-EJR 640-1071-2 640-1073-8 3 5.2 5.6 7.8 Part Number C Weight (mm) (g) 0.1 2.3 12.7 13.1 Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A5 ■Standard Left rigid button type 34.4MAX 3 59 SMT unit ( 1 ) 42.545 P= 0.635 No.1 C GND eject metal fittings movable range No.35 No.68 No.2 No.34 GND 20.5 7.4 10MAX 7MAX No.36 72 85.6: in card insertion 51.5 PUSH PUSH A 59.5 (18.6) 3 stroke:9 (27.6) 5.9 3 54.9 6 ( 34.9 ) guide unit ( 2 ) No.35 No.36 No.34 A ➀SMT unit ➁Guide unit Part Number CL No. none IC11S-68PL-1.27SF-EJL 640-1008-6 IC11S-BD-EJL 640-1072-5 IC11SA-68PL-1.27SF-EJL 640-1010-8 IC11SA-BD-EJL 640-1074-0 2.2mm Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A6 No.68 Standoff type Part Number B No.2 4.8 No.1 CL No. A (mm) B (mm) 3 5.2 5.6 7.8 C Weight (mm) (g) 0.1 2.3 12.7 13.1 ■Standard Right flexible button type 34.4 MAX 59 42.545 P=0.635 SMT unit ( 1 ) No.35 No.1 No.68 No.2 GND eject metal fittings movable range 20.5 7.4 10MAX 7MAX No.36 C GND No.34 54.9 guide unit ( 2 ) (27.6) stroke:9 button thrust volume(10.5) A 5 3 59.5 (18.6) 5.9 3 (93.6): in card ejection 72 85.6: in card insertion 51.5 PUSH PUSH A (34.55) (42.05) 4.8 No.35 Standoff type none 2.2mm No.34 No.2 A B No.1 ➀SMT unit Part Number No.68 No.36 ➁Guide unit A (mm) B (mm) 640-1075-3 3 5.6 0.1 13.1 640-1077-9 5.2 7.8 2.3 13.5 CL No. Part Number CL No. IC11S-68PL-1.27SF-EJR 640-1007-3 IC11S-BD-FEJR IC11SA-68PL-1.27SF-EJR 640-1009-9 IC11SA-BD-FEJR C Weight (mm) (g) Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A7 ■Standard Left flexible. button type 34.4MAX 59 3 SMT unit ( 1 ) 42.545 P=0.635 No.35 No.1 GND eject metal fittings movable range No.34 No.36 GND 72 85.6: in card insertion 59.5 5.9 3 (18.6) (27.6) (93.6): in card ejection 51.5 PUSH PUSH A 20.5 7.4 10 MAX 7 MAX C No.68 No.2 54.9 stroke:9 button thrust volume(10.5) 5 3 guide unit ( 2 ) (34.55) (42.05) No.35 No.36 No.34 Standoff type none 2.2mm A ➀SMT unit Part Number Part Number CL No. A (mm) B (mm) C Weight (mm) (g) IC11S-68PL-1.27SF-EJL 640-1008-6 IC11S-BD-FEJL 640-1076-6 3 5.6 0.1 13.1 IC11SA-68PL-1.27SF-EJL 640-1010-8 IC11SA-BD-FEJL 640-1078-1 5.2 7.8 2.3 13.5 Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A8 No.68 ➁Guide unit CL No. B No.2 4.8 No.1 ■Standard Right POP-UP button type 34.4 MAX 3 59 42.545 P= 0.635 SMT unit ( 1 ) No.1 No.2 No.68 No.36 No.34 eject metal fittings movable range GND C 20.5 7.4 10MAX 7MAX GND No.35 59.5 DR 3 54.9 9.1(Pop-up volume) guide unit ( 2 ) 5 none 2.2mm No.2 No.34 No.35 No.36 No.68 5 No.1 A B (35.1) Standoff type 86.4(button stored position) 5.9 3 84.5(button thrust position) 72 51.5 A PUSH PUSH A ➀SMT unit Part Number ➁Guide unit CL No. Part Number CL No. A (mm) B (mm) C Weight (mm) (g) IC11S-68PL-1.27SF-EJR 640-1007-3 IC11S-BD-PEJR 640-1081-6 3 5.7 0.1 14.7 IC11SA-68PL-1.27SF-EJR 640-1009-9 IC11SA-BD-PEJR 640-1083-1 5.2 7.9 2.3 15.1 Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A9 ■Standard Left POP-UP button type 34.4 MAX 3 59 SMT unit ( 1 ) 42.545 P= 0.635 No.1 eject metal fittings movable range No.35 No.68 No.2 No.34 No.36 GND 20.5 7.4 10MAX 7MAX C GND 72 59.5 5.9 9.1(Pop-up volume) 3 54.9 5 guide unit ( 2 ) (35.1) No.2 No.34 No.36 No.68 A 5 No.1 No.35 Standoff type none 2.2mm ➀SMT unit Part Number ➁Guide unit CL No. Part Number CL No. A (mm) A (mm) C Weight (mm) (g) IC11S-68PL-1.27SF-EJL 640-1008-6 IC11S-BD-PEJL 640-1082-9 3 5.7 0.1 14.7 IC11SA-68PL-1.27SF-EJL 640-1010-8 IC11SA-BD-PEJL 640-1084-4 5.2 7.9 2.3 15.1 Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A10 B 84.5(button thrust position) 3 DL 86.4(button stored position) 51.5 PUSH PUSH A ■Reverse Right rigid button type 34.4 MAX 3 59 42.545 SMT unit ( 1 ) P= 0.635 No.68 No.35 No.34 No.2 GND C GND 20.5 6 10MAX 7MAX No.36 eject metal fittings movable range No.1 A (18.6) 59.5 54.9 6 (34.9) stroke:9 3 (27.6) 5.9 72 85.6: in card insertion 51.5 PUSH PUSH 3 No.36 No.35 No.34 No.2 No.1 4.8 No.68 A B guide unit ( 2 ) ➀SMT unit ➁Guide unit Standoff type Part Number CL No. none IC11S-68PLR-1.27SF-EJR 640-1003-2 IC11SA-68PLR-1.27SF-EJR 640-1005-8 2.2mm CL No. A (mm) B (mm) IC11S-BUR-EJR 640-1055-6 2.7 5.6 0.1 13.1 IC11SA-BUR-EJR 640-1057-1 4.9 7.8 2.3 13.6 Part Number C Weight (mm) (g) Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A11 ■Reverse Left rigid button type 34.4 MAX 3 59 42.545 P= 0.635 No.35 No.68 eject metal fittings movable range C No.2 No.34 No.36 GND 85.6: in card insertion 72 51.5 PUSH PUSH A 20.5 6 10MAX 7MAX GND SMT unit ( 1 ) No.1 59.5 (18.6) (27.6) 5.9 3 3 54.9 6 guide unit ( 2 ) No.36 No.35 No.2 No.1 A 4.8 No.68 No.34 Standoff type none 2.2mm ➀SMT unit ➁Guide unit CL No. Part Number CL No. A (mm) B (mm) IC11S-68PLR-1.27SF-EJL 640-1004-5 IC11S-BUR-EJL 640-1056-9 2.7 5.6 0.1 13.1 IC11SA-68PLR-1.27SF-EJL 640-1006-0 IC11SA-BUR-EJL 640-1058-4 4.9 7.8 2.3 13.6 Part Number Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A12 B (34.9) C Weight (mm) (g) ■Reverse Right flexible button type 34.4 MAX 3 59 42.545 P= 0.635 No.68 SMT unit ( 1 ) GND No.34 No.35 No.1 No.2 GND eject metal fittings movable range C 20.5 6 10MAX 7MAX No.36 59.5 54.9 guide unit ( 2 ) (27.6) stroke:9 button thrust :(10.5) A 5 3 (18.6) 5.9 3 93.6: in card ejection 72 85.6: in card insertion 51.5 PUSH PUSH A ( 34.55 ) No.36 No.35 No.34 No.2 No.1 4.8 No.68 A B ( 42.05 ) ➀SMT unit ➁Guide unit Standoff type Part Number CL No. Part Number CL No. A (mm) B (mm) none IC11S-68PLR-1.27SF-EJR 640-1003-2 IC11S-BUR-FEJR 640-1059-7 2.7 5.6 0.1 13.5 IC11SA-68PLR-1.27SF-EJR 640-1005-8 IC11SA-BUR-FEJR 640-1061-9 4.9 7.8 2.3 14 2.2mm C Weight (mm) (g) Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A13 ■Reverse Left flexible button type 34.4 MAX 3 59 42.545 eject metal fittings movable range P= 0.635 No.68 No.35 No.34 No.2 GND C SMT unit ( 1 ) No.1 GND A 20.5 6 10MAX 7MAX No.36 72 85.6: in card insertion (18.6) 5.9 59.5 3 54.9 stroke:9 button thrust :(10.5) 5 ( 27.6 ) 93.6: in card ejection 51.5 PUSH PUSH 3 guide unit ( 2 ) ( 34.55 ) No.36 No.35 No.34 No.2 No.1 Standoff type none 2.2mm A 4.8 No.68 ➀SMT unit Part Number ➁Guide unit CL No. Part Number CL No. A (mm) B (mm) C Weight (mm) (g) IC11S-68PLR-1.27SF-EJL 640-1004-5 IC11S-BUR-FEJL 640-1060-6 2.7 5.6 0.1 13.5 IC11SA-68PLR-1.27SF-EJL 640-1006-0 IC11SA-BUR-FEJL 640-1062-1 4.9 7.8 2.3 14 Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A14 B ( 42.05 ) ■Reverse Right POP-UP button type 34.4 MAX 3 59 42.545 SMT unit ( 1 ) P= 0.635 No.68 No.35 No.34 No.2 GND C GND 20.5 6 10 MAX 7MAX No.36 eject metal fittings movable range No.1 A UR 54.9 9.1(Pop-up volume) 3 86.4(button stored position) 59.5 84.5(button thrust position) 5.9 72 51.5 A PUSH PUSH 3 5 guide unit ( 2 ) No.36 No.35 No.34 No.2 No.1 5 No.68 A B (35.1) ➀SMT unit ➁Guide unit Standoff type Part Number CL No. none IC11S-68PLR-1.27SF-EJR 640-1003-2 IC11SA-68PLR-1.27SF-EJR 640-1005-8 2.2mm CL No. A (mm) B (mm) IC11S-BUR-PEJR 640-1065-0 2.7 5.6 0.1 15.1 IC11SA-BUR-PEJR 640-1067-5 4.9 7.8 2.3 15.6 Part Number C Weight (mm) (g) Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A15 ■Reverse Left POP-UP button type 34.4MAX 3 59 42.545 P= 0.635 No.35 No.68 eject metal fittings movable range C No.2 No.34 No.36 GND 72 51.5 5.9 59.5 9.1(Pop-up volume) guide unit ( 2 ) 5 (35.1) No.36 No.35 No.2 No.1 A 5 No.68 No.34 Standoff type none 2.2mm ➀SMT unit ➁Guide unit CL No. Part Number CL No. A (mm) B (mm) IC11S-68PLR-1.27SF-EJL 640-1004-5 IC11S-BUR-PEJL 640-1066-2 2.7 5.6 0.1 15.1 IC11SA-68PLR-1.27SF-EJL 640-1006-0 IC11SA-BUR-PEJL 640-1068-8 4.9 7.8 2.3 15.6 Part Number Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A16 B 84.5(button thrust position) 3 UL 86.4(button stored position) PUSH PUSH A 20.5 6 10MAX 7MAX GND SMT unit ( 1 ) No.1 C Weight (mm) (g) ■PCB mounting pattern ●Standard Type ●Without standoff ●Without standoff (left button) 2-Ø2.2 +0.1 +0 2 2 3.05MIN 27.95MAX 34.5MIN 55.9MIN 59.5±0.05 2MIN (6.6) 17.9MIN 0.3MIN installed section 1.6MAX 0.8MAX 54.75±0.05 4.75±0.05 1 card edge position shielded board-pressed are 26.8MIN 21MIN 21MIN 26.8MIN shielded board-pressed area 58.1±0.05 card edge position 28.5MIN 31.4MIN 54.75±0.05 7MIN 4.75±0.05 58.1±0.05 0.8MAX 1.6MAX 17.9MIN 2 34.5 MIN 30 MIN 30 MAX 52.8±0.05 2 48.5MAX 31.4MIN 28.5MIN 7MIN (6.6) 0.8MAX installed section 34.5 MIN 30 MIN 52.8±0.05 48.5MAX 0.3MIN 30 MIN 0.8MAX (right button) 2-Ø2.2 +0.1 +0 2MIN 3.05MIN 27.95MAX 34.5MIN 2 2 55.9MIN 59.5±0.05 ●Standoff 2.2mm 52.8±0.05 installed section card edge position 58.1±0.05 47.5±0.05 54.75±0.05 50.6MAX 56.85MAX shielded boardpressed area 22.6MAX 27.6MIN (6.6) (common to both right and left buttons) 2 7MIN 2 parts installation-prohibited area 2-Ø2.2 +0.1 +0 2MIN 3.05MIN 2 59.5MAX Note.1) area and area show the pattern-inhibited area. However area will be the pattern-inhibited area only when guide unit is "IC11S-BD-PEJ✽". Note.2) Indicated dimensions are symmetrical to the center of the card insertion slot. A17 BPCB mounting pattern (Enlarged) ●Standard type 48±0.05 46.2725±0.05 3.7275±0.05 Ø1 .3 ± 0. 05 No.35 68-0.37±0.03 1.9±0.1 GND Ø1 .3 3±0.1 No.34 1.4±0.1 2±0.1 No.2 1.2±0.1 GND P=0.635±0.03 A18 No.68 No.1 1.4±0.1 3±0.1 2±0.05 ±0 .0 5 ●Reverse Type ●Without standoff ●Without standoff (left button) 2MIN 27.95MAX 34.5MIN 50.8MAX 54.6MIN 59.5±0.05 2 2 2 26.8MIN 3.05MIN 2 7MIN 26.8MIN shielded board-pressed area -Ø 25.8MIN .1 +0 0 2+ 2. 56.7±0.05 28.5MIN 54.75±0.05 12-2MIN 4.75±0.05 1 60MIN 52.8±0.05 15.2MIN card edge position 30.25±0.05 18.45±0.05 20.25±0.05 14.75±0.05 4.75±0.05 3.925±0.05 56.7±0.05 2 installed section installed section card edge position 2- Ø2 7MIN 60MIN 52.8±0.05 15.2MIN (5.2) 2MAX 2 .2 + +0 0.1 2MIN 1 shielded board-pressed area 3.05MIN 3.925±0.05 4.75±0.05 20.25±0.05 14.75±0.05 18.45±0.05 30.25±0.05 (right button) 27.95MAX 34.5MIN 2 50.8MAX 2 54.6MIN 2 59.5±0.05 ●Standoff 2.2mm 56.7±0.05 4.75±0.05 54.75±0.05 2 7MIN 2 50.6MAX 56.85MIN installed section card edge position 26.2MIN 52.8±0.05 21.2MAX (5.2) (common to both right and left buttons) parts installation-prohibited area shielded board-pressed area 2-Ø2.2 +0.1 +0 2MIN 3.05MIN 2 59.5±0.05 Note.1) area and area show the pattern-inhibited area. However area will be the pattern-inhibited area only when guide unit is "IC11S-BUR-PEJ". Note.2) Indicated dimensions are symmetrical to the center of the card insertion slot A19 BPCB mounting pattern (Enlarged) ●Reverse type A20 ■How To Install In Board(Standard Type) (1)Install SMT unit. (2)Position the lock section of guide unit into the hole of SMT unit. (3)Press the lock top of guide unit to push into SMT unit securely (i.e., until clicked.) (Note.) Avoid pressing any section other than lock top because it may cause guide plate deformation. (4)Screw 2 spots to guide unit from the back side of board. Screw designation Pitch Recommended tightening torque M2 0.4 1.5 to 2.0 (kgf • cm) A21 ■How To Install In Board(Reverse Type) (1)Install SMT unit. (2)Position the lock section of guide unit into the hole of SMT unit. (3)Press the lock top of guide unit to push into SMT unit securely (i.e., until clicked.) (Note.) Avoid pressing any section other than lock top because it may cause guide plate deformation. (4)Screw 2 spots to guide unit from the back side of board. A22 Screw designation Pitch Recommended tightening torque M2 0.4 1.5 to 2.0 (kgf • cm) ■PreCautions In Installation To Boards 1. After installation of SMT unit to boards, verify that the stroke arm of SMT unit and the push rod of guide unit are located on the positions shown in fig.➀. Also note that guide unit cannot be solder reflowed. Pict.➀ Guide unit SMT unit Push rod Stroke arm 2. Note that the stroke arm of SMT unit and the push rod of guide unit cannot be combined when located in the position as shown in fig.➁. Pict.➁ Guide unit SMT unit If located in the position shown in fig.➁ move it to the position shown in fig. ➀ by fingers. Guide unit SMT unit 3. After SMT unit and guide unit are combined, state will be found as follows : ●When the push rod was pressed: intervention ●When the push rod was extracted: intervention A23 ■Pre Caution In Handling Guide plate is metallic, having some sharp-edged portions. Handle carefully to prevent injury to fingers. Do not wrench the card up and down severely in the midst of insertion. This may cause damage to the connectors or cards. Up Down A24 ■Temperature Profile 5sec.max board surface temperature(ç) 250 240ç 200 200ç Applicable Conditions Reflow system : IR reflow 160ç 150 150ç Solder : Paste type 63 Sn/37 Pb (Flux content 9 wt%) 100 Test board Glass epoxy 60mm x 60mm x 1.6 mm Metal mask thickness: 0.15 mm 50 25ç 0 start Recommended temperature profile. (30s) 60-90s preheating time (60s) 60 120 (20-30s) soldering time The temperature may be slightly changed according to the solder paste type and amount. time(seconds) A25 Single Slot SMT Connectors For Card-Bus Based PC Cards IC11S Series (New POP-UP Button) PC Card Standard Compliant Reduced height : 5.6mm high ■Features Wide variety of options 1. PC Card Standard compliant: (1)Board Mounting ➀Standard type ➁Reverse type • Grounding is required to meet the high speed signal requirements of the PC card standard. Grounding reliability is achieved with a grounding plate and 8 grounding contacts. • Type1, type2and type3cards are covered. • Terminals for ground clipping are provided. 2. Reduced pattern-inhibited area Pattern-inhibited area is reduced,compared to our conventional product. 3. Light-Weight (2)Position of eject buttons ➀Right ➁Left (3)Standoffs ➀0.0mm ➁2.2mm Approx. 12% of weight reduced. Compared to conventional type, it only weighs 13.1g for standard type with 0mm standoff. 4. Reduced Height: Connector height is minimized to 5.6mm, making possible thinner product designs. 5. Eject mechanism with high-level functionality Hirose Electric's original ejection mechanism provides an higher degree of card ejection over existing products. This improves the operational qualities of card removal. (Patents pending) Standard type 6. Wide Variety of Options Available • Standard type mounts to the top of the PC board and reverse type mounts on the underside of the board • Three types of eject buttons; rigid, flexible and POP-UP.All types can be installed on the right or left side of the ejector. • Available with standoff to utilize space under the connector for mounting other parts. Reverse type A26 ■Product Specifications Ratings Current rating 0.5A Operating temperature Voltage rating 125V AC Operating humidity Item -55ç to +85ç(Note.1) Storage temperature Relativehumidity 95% or less Storage humidity (With no dew-fall) Specification -40ç to +70ç(Note.2) 40% to 70%(Note.2) Conditions 1.Insulation resistance 1000M ohms min. 500V DC 2.Withstanding voltage No flashover or insulation breakdown. 500V AC 3.Contact resistance 60m ohms max. (initial value) 1mA 4.Vibration No electrical discontinuity of 100ns or more Frequency: 10 to 2000 Hz, full amplitude of 1.52 mm or acceleration of 147 m/s2(peak), 4 hours in each of the 3 directions. 5.Humidity (Steady state) Insulation resistance: 100M ohms min. 6.Temperature cycle Insulation resistance: 100M ohms min. 7.Durability (Insertion/withdrawal) Variations from initial contact resistance: 20m ohms max. 8.Resistance to Soldering heat No deformation of components affecting performance. 96 hours at temperature of 40ç and humidity of 90% to 95% (-55ç:30min.➝+5ç to 35ç:MAX 5min➝85ç:30min➝ (+5-35ç:MAX 5min.) 5 cycles 10000 cycles at 400 to 600 cycles per hour Reflow: At the recommended temperature profile Manual soldering: 300ç for 3 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. ■Materials ●SMT unit Parts Material Insulator PPS Card connected section Brass Ground plate Phosphor bronze Terminal Stainless steel Eject metal fittings Finish Remarks Color : Black UL94V-0 Contact section: gold plating Lead section: solder plating Contact section: gold plating Lead section: solder plating ––––– ––––– ––––– ––––– ●Guide unit Description Material Finish Remarks Guide plate Stainless steel ––––– ––––– Push rod Stainless steel Eject Button ––––– ––––– Resin section PBT Color : Black UL94V-0 Spring Steel ––––– ––––– Zinc alloy ––––– ––––– Cam A27 ■Ordering Information ●SMT Unit IC11S A - 68 PLR - 1.27SF - EJ R 1 1 Series name : IC11S 2 Standoff type 2 3 4 5 Blank : none A 6 7 5 1.27SF : 1.27mm pitch SMT connector 6 With ejector 7 Eject button positions : 2.2mm 3 Number of contacts : 68 4 Board Mounting Method: PL R : right : standard type L : left PLR : reverse type ●Guide Unit IC11S A - BUR - PNEJ R 8 8 Series name : IC11S 9 Standoff type 9 10 11 11 12 Eject button type PNEJ : POP-UP button Blank: none A : 2.2mm 10 Board Mounting Method BD 12 : standard type Eject button positions R : right BUR : reverse type L : left (Note.) IC11S Series will be used in combination of SMT unit with guide unit. When using, please select the same type for the following items. Note that other combinations cannot be used. • Series name • Standoff type • Board Mounting Method • Eject button positions A28 (1⇔8) (2⇔9) ( 4 ⇔ 10 ) ( 7 ⇔ 12 ) ■Standard Right POP-UP button type 34.4MAX 3 59 42.545 No.35 SMT Unit(1) eject metal fittings movable range No.2 No.36 C No.68 GND No.34 10 MAX 7.4 7 MAX No.1 GND P=0.635 20.5 AS A PUSH PUSH 59.5 ( 17.55) 5.9 3 86.3 (button stored position) 84.3 (button thrust position) ( 28.05) 72 51.5 PNL 2.35 11.8 NR NDRA 27.45 No.2 No.34 5 B 5 No.1 A Guide unit(2) No.35 Standoff type 0mm 2.2mm ➀SMT unit Part Number No.36 No.68 ➁Guide unit CL No. 10.1(Pop-up volume) ( 35.05 ) (66.25) Part Number CL No. A (mm) B (mm) C (mm) mass (g) IC11S-68PL-1.27SF-EJR 640-1007-3 IC11S-BD-PNEJR 640-1251-4 3 5.6 0.1 13.1 IC11SA-68PL-1.27SF-EJR 640-1009-9 IC11SA-BD-PNEJR 640-1253-0 5.2 7.8 2.3 13.6 Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A29 ■Standard Left POP-UP button type 34.4MAX 3 59 42.545 eject metal fittings movable range P=0.635 No.35 C SMT Unuit(1) No.2 No.36 No.68 GND No.34 10MAX 7.4 7MAX No.1 GND 20.5 AS PUSH PUSH 72 59.5 10.1(Pop-up volume) (17.55) 5.9 3 (28.05) 84.3(button stored position) 86.3(button thrust position) 51.5 PNR 11.8 2.35 NL NDLA 27.45 (35.05) (66.25) No.1 No.2 No.34 Guide unit(2) A B 5 5 No.35 Standoff type 0mm 2.2mm No.36 ➀SMT unit Part Number No.68 ➁Guide unit CL No. Part Number A (mm) B (mm) C (mm) mass (g) IC11S-68PL-1.27SF-EJL 640-1008-6 IC11S-BD-PNEJL 640-1252-7 3 5.6 0.1 13.1 IC11SA-68PL-1.27SF-EJL 640-1010-8 IC11SA-BD-PNEJL 640-1254-2 5.2 7.8 2.3 13.6 Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A30 CL No. ■Reverse Right POP-UP button type 34.4 MAX 3 59 42.545 SMT Unit(1) P=0.635 No.2 No.36 eject metal fittings movable range No.35 No.1 GND C 20.5 10MAX 6 7 MAX No.34 No.68 GND A 10.1(Pop-up volume) ( 17.55 ) 86.3(button stored position) 59.5 84.3(button thrust position) 3 5.9 72 ( 28.05 ) 51.5 PNR 2.35 11.8 NURA 27.45 ( 35.05 ) ( 66.25 ) 5 Guide unit(2) No.36 No.35 A B 5 No.68 No.34 ➀SMT unit No.2 No.1 ➁Guide unit Standoff type Part Number CL No. Part Number CL No. A (mm) B (mm) C (mm) mass (g) 0mm IC11S-68PLR-1.27SF-EJR 640-1003-2 IC11S-BUR-PNEJR 640-1255-5 2.7 5.6 0.1 13.3 IC11SA-68PLR-1.27SF-EJR 640-1005-8 IC11SA-BUR-PNEJR 640-1257-0 4.9 7.8 2.3 13.7 2.2mm Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A31 ■Reverse Left POP-UP button type 34.4 MAX 59 42.545 3 eject metal fittings movable range P=0.635 No.34 No.68 GND SMT Unit(1) No.35 No.1 GND 20.5 10 MAX 6 7 MAX C No.2 No.36 A PUSH PUSH 72 (28.05 ) 59.5 5.9 3 10.1 (Pop-up volume) (17.55 ) 84.3 (button stored position) 86.3 (button thrust position) 51.5 PNL 2.35 11.8 NULA 27.45 ( 35.05 ) ( 66.25 ) 5 No.36 No.35 Guide unit(2) A B 5 No.68 No.34 Standoff type ➀SMT unit Part Number No.2 No.1 ➁Guide unit CL No. Part Number CL No. A (mm) B (mm) C (mm) mass (g) 0mm IC11S-68PLR-1.27SF-EJL 640-1004-5 IC11S-BUR-PNEJL 640-1256-8 2.7 5.6 0.1 13.3 2.2mm IC11SA-68PLR-1.27SF-EJL 640-1006-0 IC11SA-BUR-PNEJL 640-1258-3 4.9 7.8 2.3 13.7 Note.1) This figure illustrates grouping of SMT unit(➀) and guide unit(➁) together. Note.2) Dimensions for card fitting are in accordance with "PC Card Standard". Note.3) Indicated dimensions are symmetrical to the center of the card insertion slot. A32 BPCB mounting pattern ●Standard Type ●Without standoff ●Without standoff (left button) 2-Ø2.2 +0.1 0 3.05MIN 2 2 52.8±0.05 48.5MAX 17.9MIN 0.3MIN 2 Installed cection 1.6MAX 0.8MAX 21MIN Shielded boardpressed area 30 MIN 54.75±0.05 4.75±0.05 2MIN 2-Ø2.2 +0.1 0 2MIN 55.9MIN 59.5±0.05 Card edge position Shielded boardpressed area 21MIN Card edge position 7MIN 31.4MIN 54.75±0.05 58.1±0.05 4.75±0.05 58.1±0.05 0.8MAX 1.6MAX 17.9MIN 2 34.5 MIN 30MAX 31.4MIN 7MIN (6.6) 0.8MAX Installed cection 34.5 MIN 30MAX 52.8±0.05 48.5MAX 0.3MIN 30 MIN 0.8MAX (6.6) (right button) 3.05MIN 2 2 55.9MIN 59.5±0.05 ●Standoff 2.2mm 52.8±0.05 Installed cection Card edge position 58.1±0.05 4.75±0.05 54.75±0.05 2 2 50.6MAX 56.85MIN 22.6MAX 27.6MIN (6.6) (common to both right and left buttons) Parts installation prohibited area 7MIN Shielded board-pressed area 2-Ø2.2 +0.1 0 2MIN 3.05MIN 2 59.5±0.05 Note.1) area show the pattern-inhibited area. Note.2) Indicated dimensions are symmetrical to the center of the card insertion slot. BPCB mounting pattern (Enlarged) ●Standard type A33 BPCB mounting pattern ●Reverse Type ●Without standoff (common to both right and left buttons) 2MAX .1 +0 0 2 4.75±0.05 2Ø2 .2 2MIN 7MIN 2 7MIN 3.05MIN 2. -Ø Card edge position 54.75±0.05 +0 . 0 1 2MIN Shielded board-pressed area 3.05MIN 1 4.75±0.05 3.925±0.05 20.25±0.05 14.75±0.05 18.45±0.05 30.25±0.05 56.7±0.05 12-2MIN 56.7±0.05 30.25±0.05 18.45±0.05 20.25±0.05 14.75±0.05 3.925±0.05 4.75±0.05 54.75±0.05 Shielded board-pressed area Installed cection 15.2MIN (5.2) 2MAX 15.2MIN (5.2) Card edge position 4.75±0.05 60MIN 52.8±0.05 2 Installed cection 12-2MIN 60MIN 52.8±0.05 2 1 50.8MAX 54.6MIN 59.5±0.05 2 2 2 2 2 2 50.8MAX 54.6MIN 59.5±0.05 ●Standoff 2.2mm 54.75±0.05 2 7MIN 2 50.6MAX 56.85MIN Card edge position 21.2MAX 4.75±0.05 Installed cection 26.2MIN 52.8±0.05 56.7±0.05 (5.2) (common to both right and left buttons) Parts installation prohibited area Shielded board-pressed area 2-Ø2.2 +0.1 0 2MIN 3.05MIN 2 59.5±0.05 BPCB mounting pattern (Enlarged) ●Reverse type A34 Note.1) area show the pattern-inhibited area. Note.2) Indicated dimensions are symmetrical to the center of the card insertion slot. BHow To Install In Board(Standard Type) (1)Install SMT unit. (2)Position the lock section of guide unit into the hole of SMT unit. (3)Press the lock top of guide unit to push into SMT unit securely (i.e., until clicked.) (Note.) Avoid pressing any section other than lock top because it may cause guide plate deformation. (4)Screw 2 spots to guide unit from the back side of board. Screw designation Pitch Recommended tightening torque M2 0.4 0.14 to 0.18 (N • m) A35 BHow To Install In Board(Reverse Type) (1)Install SMT unit. (2)Position the lock section of guide unit into the hole of SMT unit. (3)Press the lock top of guide unit to push into SMT unit securely (i.e., until clicked.) (Note.) Avoid pressing any section other than lock top because it may cause guide plate deformation. (4)Screw 2 spots to guide unit from the back side of board. A36 Screw designation Pitch Recommended tightening torque M2 0.4 0.14 to 0.18 (N • m) BCautions In Installation To Boards 1. After installation of SMT unit to boards, verify that the stroke arm of SMT unit and the push rod of guide unit are located on the positions shown in fig.➀. Also note that guide unit cannot be solder reflowed. Pict.➀ Guide unit SMT unit Push rod Stroke arm 2. Note that the stroke arm of SMT unit and the push rod of guide unit cannot be combined when located in the position as shown in fig.➁. Pict.➁ Guide unit SMT unit If located in the position shown in fig.➁ move it to the position shown in fig. ➀ by fingers. Guide unit SMT unit 3. After SMT unit and guide unit are combined, state will be found as follows : ●When the push rod was pressed: ●When the push rod was extracted: intervention intervention A37 BCaution In Handling Guide plate is metallic, having some sharp-edged portions. Handle carefully to prevent injury to fingers. Do not wrench the card up and down severely in the midst of insertion. This may cause damage to the connectors or cards. Up Down A38 BInstallation Temperature Profile 5sec.max board surface temperature(ç) 250 240ç 200 200ç Applicable Conditions Reflow system : IR reflow 160ç 150 150ç Solder : Paste type 63 Sn/37 Pb (Flux content 9 wt%) 100 Test board Glass epoxy 60mm x 60mm x 1.6 mm Metal mask thickness: 0.15 mm 50 25ç 0 start Recommended temperature profile. (30s) 60-90s preheating (60s) 60 (20-30s) soldering 120 The temperature may be slightly changed according to the solder paste type and amount. time(seconds) A39