Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Film Type Data Sheet 1 Common Mode Choke Coil Film Type DLP11S/DLP11R/DLP11T Series (0504 Size) ■ Dimensions ■ Equivalent Circuit (1) 0.55±0.1 (2) 1.0±0.1 T 0.3±0.1 Part Number T DLP11S 0.82±0.1 DLP11R 0.5±0.1 DLP11T 0.3±0.05 (1) (2) (4) (3) (3) (4) No polarity. 0.25+0.1 –0.05 : Electrode 1.25±0.1 (in mm) ■ Impedance-Frequency Characteristics (Main Items) ■ Impedance-Frequency Characteristics (Main Items) DLP11SN Series DLP11SA Series 1000 10000 Common mode DLP11SN331HL2 DLP11SN281HL2 DLP11SN241HL2 DLP11SN201HL2 DLP11SN161SL2 DLP11SN121SL2 DLP11SN900HL2 DLP11SN670SL2 100 10 1 1 10 Common mode 100 Impedance (Ω) Impedance (Ω) 1000 DLP11SN331HL2 DLP11SN281HL2 DLP11SN241HL2 DLP11SN201HL2 DLP11SN161SL2 DLP11SN121SL2 DLP11SN900HL2 DLP11SN670SL2 Differential mode 100 Frequency (MHz) 1000 DLP11SA900HL2 DLP11SA670HL2 DLP11SA350HL2 10 DLP11SA900HL2 DLP11SA670HL2 DLP11SA350HL2 Differential mode 1 10000 ■ Impedance-Frequency Characteristics (Main Items) 1 10 100 Frequency (MHz) 1000 10000 ■ Impedance-Frequency Characteristics (Main Items) DLP11RN Series DLP11RB Series 1000 1000 Common mode 100 Impedance (Ω) Impedance (Ω) Common mode DLP11RN450UL2 DLP11RN450UL2 10 DLP11RB150UL2 DLP11RB400UL2 100 10 DLP11RB150UL2 DLP11RB400UL2 Differential mode Differential mode 1 1 10 100 Frequency (MHz) 1000 10000 1 1 10 100 Frequency (MHz) 1000 10000 Continued on the following page. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.7.7 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Film Type Data Sheet 2 Continued from the preceding page. ■ Impedance-Frequency Characteristics (Main Items) DLP11TB Series 1000 Common Mode 100 Impedance (Ω) DLP11TB800UL2 DLP11TB800UL2 10 Differential Mode 1 1 10 100 Frequency (MHz) 1000 10000 ■ Differential Mode Transmission Characteristics (Typ.) ■ Differential Mode Transmission Characteristics (Typ.) DLP11SN Series DLP11SA Series 0 0 2 2 DLP11SA900HL2 Insertion Loss (dB) Insertion Loss (dB) DLP11SN900HL2 4 6 8 4 6 8 10 10 1 10 100 Frequency (MHz) 1000 10000 ■ Differential Mode Transmission Characteristics (Typ.) 1 10 1000 10000 ■ Differential Mode Transmission Characteristics (Typ.) DLP11RN Series DLP11RB Series 0 0 2 2 DLP11RB400UL2 Insertion Loss (dB) DLP11RN450UL2 Insertion Loss (dB) 100 Frequency (MHz) 4 6 8 4 6 8 10 10 1 10 100 Frequency (MHz) 1000 10000 1 10 100 Frequency (MHz) 1000 10000 Continued on the following page. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.7.7 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Film Type Data Sheet 3 Continued from the preceding page. ■ Differential Mode Transmission Characteristics (Typ.) DLP11TB Series ■ Packaging Code Packaging Minimum Quantity L 180mm Embossed Tape 4000 (DLP11R) B Bulk(Bag) 3000 (DLP11S) 0 DLP11TB800UL2 Insertion Loss (dB) 2 5000 (DLP11T) 500 4 6 8 10 1 10 100 Frequency (MHz) 1000 10000 ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Rated Current Rated Voltage Insulation Resistance (min.) Withstand Voltage DC Resistance Operating Temperature Range DLP11SN670SL2p 67ohm ±20% 180mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% -40 to +85°C DLP11SN121SL2p 120ohm ±20% 140mA 5Vdc 100M ohm 12.5Vdc 2.0ohm±25% -40 to +85°C DLP11SN161SL2p 160ohm ±20% 120mA 5Vdc 100M ohm 12.5Vdc 2.7ohm±25% -40 to +85°C DLP11SN900HL2p 90ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.5ohm±25% -40 to +85°C DLP11SN201HL2p 200ohm ±20% 110mA 5Vdc 100M ohm 12.5Vdc 3.1ohm±25% -40 to +85°C DLP11SN241HL2p 240ohm ±20% 100mA 5Vdc 100M ohm 12.5Vdc 3.5ohm±25% -40 to +85°C DLP11SN281HL2p 280ohm ±20% 90mA 5Vdc 100M ohm 12.5Vdc 4.2ohm±25% -40 to +85°C DLP11SN331HL2p 330ohm ±20% 80mA 5Vdc 100M ohm 12.5Vdc 4.9ohm±25% -40 to +85°C DLP11SA350HL2p 35ohm ±20% 170mA 5Vdc 100M ohm 12.5Vdc 0.9ohm±25% -40 to +85°C DLP11SA670HL2p 67ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.2ohm±25% -40 to +85°C DLP11SA900HL2p 90ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 1.4ohm±25% -40 to +85°C DLP11RN450UL2p 45ohm ±25% 100mA 5Vdc 100M ohm 12.5Vdc 0.8ohm±25% -40 to +85°C DLP11RB150UL2p 15ohm ±5ohm 100mA 5Vdc 100M ohm 12.5Vdc 0.8ohm±25% -40 to +85°C DLP11RB400UL2p 40ohm ±10ohm 100mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% -40 to +85°C DLP11TB800UL2p 80ohm ±25% 100mA 5Vdc 100M ohm 12.5Vdc 1.5ohm±25% -40 to +85°C Number of Circuit: 1 Differential mode to common mode conversion characteristic (Scd21) at 2.5GHz: -40dB (typ./DLP11TB800UL2) Impedance Characteristics between signal lines Z0 (TDR at 50ps): 90ohm±15ohm (DLP11TB800UL2) ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.7.7 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Film Type (Array) Data Sheet 1 Common Mode Choke Coil Film Type (Array) DLP2AD Series (0804 Size) ■ Dimensions ■ Equivalent Circuit 0.5±0.1 (1) (2) (3) (4) (5) (6) (7) (8) (1) (2) (3) (4) (5) (6) (7) (8) 1.0±0.1 0.25±0.15 0.82±0.1 0.25±0.1 2.0±0.1 : Electrode No polarity. (in mm) ■ Impedance-Frequency Characteristics (Main Items) ■ Impedance-Frequency Characteristics (Main Items) DLP2ADA Series DLP2ADN Series 10000 1000 Common Mode Common mode DLP2ADN281HL4 DLP2ADN241HL4 DLP2ADN201HL4 DLP2ADN161HL4 DLP2ADN121HL4 DLP2ADN900HL4 DLP2ADN670HL4 DLP2ADA900HL4 1000 Impedance (Ω) Impedance (Ω) DLP2ADA670HL4 100 DLP2ADA350HL4 DLP2ADA900HL4 100 10 10 DLP2ADA670HL4 DLP2ADA350HL4 Differential Mode 1 1 10 100 Frequency (MHz) 1000 DLP2ADN670HL4 1 10000 ■ Differential Mode Transmission Characteristics (Typ.) 1 10 1000 10000 DLP2ADN Series 0 0 2 2 DLP2ADA900HL4 DLP2ADN900HL4 Insertion Loss (dB) Insertion Loss (dB) 100 Frequency (MHz) ■ Differential Mode Transmission Characteristics (Typ.) DLP2ADA Series 4 6 4 6 8 8 10 10 DLP2ADN281HL4 DLP2ADN241HL4 DLP2ADN201HL4 DLP2ADN161HL4 DLP2ADN121HL4 Differential mode DLP2ADN900HL4 10 100 1000 10000 Frequency (MHz) 1 10 100 Frequency (MHz) 1000 10000 Continued on the following page. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.5.12 http://www.murata.com/ Noise Suppression Products/EMI Suppression Filters > Common Mode Choke Coil > Film Type (Array) Data Sheet 2 Continued from the preceding page. ■ Packaging Code Packaging Minimum Quantity L 180mm Embossed Tape 3000 B Bulk(Bag) 500 ■ Rated Value (p: packaging code) Part Number Common Mode Impedance (at 100MHz/20°C) Insulation Resistance (min.) Withstand Voltage DC Resistance Operating Temperature Range DLP2ADA350HL4p 35ohm ±20% 150mA 5Vdc 100M ohm 12.5Vdc 0.8ohm±25% -40 to +85°C DLP2ADA670HL4p 67ohm ±20% DLP2ADA900HL4p 90ohm ±20% 130mA 5Vdc 100M ohm 12.5Vdc 1.0ohm±25% -40 to +85°C 120mA 5Vdc 100M ohm 12.5Vdc 1.4ohm±25% -40 to +85°C DLP2ADN670HL4p DLP2ADN900HL4p 67ohm ±20% 140mA 5Vdc 100M ohm 12.5Vdc 1.3ohm±25% -40 to +85°C 90ohm ±20% 130mA 5Vdc 100M ohm 12.5Vdc 1.7ohm±25% -40 to +85°C DLP2ADN121HL4p 120ohm ±20% 120mA 5Vdc 100M ohm 12.5Vdc 2.0ohm±25% -40 to +85°C DLP2ADN161HL4p 160ohm ±20% 100mA 5Vdc 100M ohm 12.5Vdc 2.5ohm±25% -40 to +85°C DLP2ADN201HL4p 200ohm ±20% 90mA 5Vdc 100M ohm 12.5Vdc 3.2ohm±25% -40 to +85°C DLP2ADN241HL4p 240ohm ±20% 80mA 5Vdc 100M ohm 12.5Vdc 3.8ohm±25% -40 to +85°C DLP2ADN281HL4p 280ohm ±20% 80mA 5Vdc 100M ohm 12.5Vdc 4.6ohm±25% -40 to +85°C Rated Current Rated Voltage Number of Circuit: 2 ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current and rated voltage as this may create excessive heat and deteriorate the insulation resistance. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP COMMON MODE CHOKE COIL used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2011.5.12 http://www.murata.com/