FMS2016-001 Datasheet v3.0 High Power Reflective GaAs SP4T Switch FEATURES: • • • • • • FUNCTIONAL SCHEMATIC: 3x3x0.9mm Packaged pHEMT Switch High isolation: >30dB at 1.8GHz Low Insertion loss: 0.65dB at 1.8GHz Excellent low control voltage performance Excellent harmonic performance under GSM/DCS/PCS/EDGE power levels RoHS Compliant (Directive 2002/95/EC) ANT RF1 RF2 RF3 RF4 GENERAL DESCRIPTION: The FMS2016-001 is a low loss, high power and linear single pole four throw Gallium Arsenide antenna switch designed for use in mobile handset and other high power switching applications. The die is fabricated using the Filtronic FL05 0.5µm switch process technology, which offers excellent performance optimised for switch applications. TYPICAL APPLICATIONS: • • Multi-band GSM/DCS/PCS/EDGE handset modules High power and linear RF switching applications . ELECTRICAL SPECIFICATIONS: Parameter Test Conditions Min Typ Max Units 0.5 – 1.0 GHz 0.55 0.75 dB 1.0 – 2.0 GHz 0.65 0.85 dB Insertion Loss Return Loss 0.5 – 2.5 GHz Isolation 0.5 – 1.0 GHz RF1 – RF2, RF1 – RF3, RF2 – RF4 1.0 – 2.0 GHz Isolation 0.5 – 1.0 GHz RF3 – RF4 1.0 – 2.0 GHz 16 30 26 20 dB 34 dB 32 dB 34 dB 30 dB 1 GHz, Pin = +35 dBm, 100% Duty Cycle -75 -60 dBc 2 GHz, Pin = +35 dBm, 100% Duty Cycle -75 -65 dBc 1 GHz, Pin = +35 dBm, 100% Duty Cycle -75 -60 dBc 2 GHz, Pin = +35 dBm, 100% Duty Cycle -75 -65 dBc 2nd Harmonic Level 3rd Harmonic Level µs Switching speed : Trise, Tfall 10% to 90% RF and 90% to 10% RF Ton, Toff 50% control to 90% RF and 50% control to 10% RF Control Current +35dBm RF input @1GHz <10 0.9 & 0.91 GHz, Pin = +20 dBm >68 dBm 1.85 & 1.86 GHz, Pin = +20 dBm >66 dBm 1.0GHz >38 dBm 2.0GHz >37 dBm <0.3 0.5 µs 15 µA IP3 P0.1dB Note: TAMBIENT = 25°C, Vctrl = 0V/2.7V, ZIN = ZOUT = 50Ω External DC blocking capacitors are required on all RF ports (typ: 47pF) 1 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMS2016-001 Datasheet v3.0 ABSOLUTE MAXIMUM RATINGS: PARAMETER SYMBOL ABSOLUTE MAXIMUM Max Input Power Pin +38dBm Control Voltage Vctrl +6V Operating Temperature Toper -40°C to +100°C Storage Temperature Tstor -55°C to +150°C Note: Exceeding any one of these absolute maximum ratings may cause permanent damage to the device. TRUTH TABLE: V1 V2 V3 V4 PATH(S) High Low Low Low RF1 to ANT Low High Low Low RF2 to ANT Low Low High Low RF3 to ANT Low Low Low High RF4 to ANT Note: High: 2.7V to 6V; Low: 0V to 0.2V PAD LAYOUT: V1 Pin 1 12 ANT 11 V2 10 RF1 GND RF3 PADDLE 2 3 4 5 V3 9 RF2 8 GND 7 RF4 PAD REF PAD NAME DESCRIPTION 1 RF1 RF Port 1 2 GND Ground Connection 3 RF3 RF Port 3 4 V3 Vctrl3 (ANT to RF3) 5 N/C No Connection 6 V4 Vctrl4 (ANT to RF4) 7 RF4 RF Port 4 8 GND Ground Connection 9 RF2 RF Port 2 10 V2 Vctrl2 (ANT to RF2) 11 ANT Antenna Port 12 V1 Vctrl1 (ANT to RF1) 6 V4 2 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMS2016-001 Datasheet v3.0 TYPICAL MEASURED PERFORMANCE ON EVALUATION BOARD: Note: Measurement Conditions VCTRL= 0V (low) & 2.5V (high), TAMBIENT = 25°C unless otherwise stated Insertion Loss RF1 to RF2 Isolation FMS2016QFN RF1 to RF2 ISOLATION FMS2016QFN INSERTION LOSS 0 0 -0.1 -5 -0.2 -10 -0.3 -0.4 -15 dB dB -0.5 -0.6 -0.7 -20 -25 -0.8 -0.9 -30 -1 -35 -1.1 -1.2 -40 0.5 1 1.5 2 Frequency (GHz) 2.5 3 3.5 0.5 RF3 to RF4 Isolation 1.5 2 Frequency (GHz) 2.5 3 3.5 RF1 to RF3 AND RF2 to RF4 Isolation FMS2016QFN RF3 to RF4 ISOLATION FMS2016QFN RF1 to RF3 and RF2 to RF4 ISOLATION 0 0 -5 -5 -10 -10 -15 -15 dB dB 1 -20 -20 -25 -25 -30 -30 -35 -35 -40 -40 0.5 1 1.5 2 Frequency (GHz) 2.5 3 0.5 3.5 1 1.5 2 Frequency (GHz) 2.5 3 3.5 Return Loss FMS2016QFN RETURN LOSS -15 -20 dB -25 -30 -35 -40 0.5 1 1.5 2 Frequency (GHz) 2.5 3 3.5 3 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMS2016-001 Datasheet v3.0 EVALUATION BOARD COMPONENT SIDE LAYOUT: C1 C1 C1 C1 C1 C2 C2 C2 C2 BILL OF MATERIALS: LABEL COMPONENT Board Preferred evaluation board material is 0.25 mm thick ROGERS RT4350. All RF tracks should be 50 ohm characteristic material. RFC SMA RF connector DCC DC connector C1 Capacitor, 47pF, 0402 C2 Capacitor, 470pF, 0603 EVALUATION BOARD DE-EMBEDDING DATA (MEASURED): Insertion Loss Return Loss FMS2016QFN CALIBRATION BOARD INSERTION LOSS FMS2016QFN CALIBRATION BOARD RETURN LOSS 0 -15 -0.1 -0.2 -20 -0.3 -25 dB dB -0.4 -0.5 -0.6 -30 -0.7 -0.8 -35 -0.9 -1 -40 0.5 1 1.5 2 Frequency (GHz) 2.5 3 3.5 0.5 1 1.5 2 Frequency (GHz) 2.5 3 3.5 4 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMS2016-001 Datasheet v3.0 QFN 12 LEAD 3*3 PACKAGE OUTLINE: Note: PIN1 Identifier is at ground potential TAPE & REEL SPECIFICATION: TAPE DIMENSIONS DESCRIPTION SYMBOL SIZE (MM) Perforation Diameter D0 1.5 ±0.1 Pitch P0 4.0 ±0.1 Position E1 1.75 ±0.1 Length A0 3.3 ±0.1 Width B0 3.3 ±0.1 Depth K 1.1 ±0.1 Cavity to Perforation P2 2.0 ±0.1 F 5.5 ±0.1 W 12 ±0.3 Cavity Distance between centrelines (length direction) Cavity to Perforation (width direction) Carrier tape Width 5 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com FMS2016-001 Datasheet v3.0 PREFERRED ASSEMBLY INSTRUCTIONS: Available on request APPLICATION NOTES & DESIGN DATA: HANDLING PRECAUTIONS: Application Notes and design data, including S-parameters are available on request. To avoid damage to the devices care should be exercised during handling. Proper Electrostatic Discharge (ESD) precautions should be observed at all stages of storage, handling, assembly, and testing. These devices should be treated as Class 1A (250-500 V) as defined in JEDEC Standard No. 22-A114. Further information on ESD control measures can be found in MIL-STD1686 and MIL-HDBK-263. DISCLAIMERS: This product is not designed for use in any space based or life sustaining/supporting equipment. ORDERING INFORMATION: PART NUMBER DESCRIPTION Packaged Die FMS2016-001-TR Tape & Reel (minimum quantity: 1k pcs) FMS2016-001-TB FMS2016-001-EB Packaged Die supplied in a Tube Packaged Die mounted on Evaluation Board 6 Tel: +44 (0) 1325 301111 Specifications subject to change without notice Filtronic Compound Semiconductors Ltd Fax: +44 (0) 1325 306177 Email: [email protected] Website: www.filtronic.com