Maxim MAX5400EKA-T 256-tap sot-pot, low-drift digital potentiometers in sot23 Datasheet

19-1848; Rev 0; 10/00
256-Tap SOT-PoT,
Low-Drift Digital Potentiometers in SOT23
Features
♦ Miniature 8-Pin SOT23 (3mm x 3mm)
♦ 256 Tap Positions
♦ Ultra-Low 0.1µA Supply Current
♦ Single-Supply Operation: +2.7V to +5.5V
♦ Low Ratiometric Temperature Coefficient:
5ppm/°C
♦ Power-On Reset: Wiper Goes to Midscale
(Position 128)
♦ Glitchless Switching Between the Resistor Taps
The MAX5400/MAX5401 serve well in applications
requiring digitally controlled resistors, including
adjustable voltage references and programmable gain
amplifiers (PGAs). A nominal end-to-end resistor temperature coefficient of 50ppm/°C allows these parts to
be used as variable resistors in applications such as
low-tempco adjustable gain and other circuit configurations.
♦ 3-Wire SPI™-Interface Compatible
♦ 50kΩ/100kΩ Resistor Values
Ordering Information
Two resistance values are available: 50kΩ (MAX5400)
and 100kΩ (MAX5401). Each device is guaranteed over
the extended industrial temperature range (-40°C to
+85°C).
TEMP.
RANGE
PART
________________________Applications
PINPACKAGE
R (kΩ)
MAX5400EKA-T
-40°C to +85°C
8-SOT23
50
MAX5401EKA-T
-40°C to +85°C
8-SOT23
100
SOT-PoT is a trademark of Maxim Integrated Products.
SPI is a trademark of Motorola, Inc.
Mechanical Potentiometer Replacement
Low-Drift PGAs
Pin Configuration appears at end of data sheet.
Adjustable Voltage References
Functional Diagram
VDD
H
8
DIN
8-BIT
SHIFT
REGISTER
8
8-BIT
LATCH
DECODER
W
L
MAX5400/MAX5401
SCLK
CS
CLOCK
LOGIC
POR
GND
________________________________________________________________ Maxim Integrated Products
1
For price, delivery, and to place orders, please contact Maxim Distribution at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX5400/MAX5401
General Description
The MAX5400/MAX5401 digital potentiometers offer
256-tap SOT-PoT™ digitally controlled variable resistors in tiny 8-pin SOT23 packages. Each device functions as a mechanical potentiometer, consisting of a
fixed resistor string with a digitally controlled wiper contact. They operate from +2.7V to +5.5V single-supply
voltages and use an ultra-low supply current of 0.1µA.
These devices also provide glitchless switching
between resistor taps, as well as a convenient poweron reset that sets the wiper to the midscale position at
power-up. A low 5ppm/°C ratiometric temperature coefficient makes it ideal for applications requiring low drift.
MAX5400/MAX5401
256-Tap SOT-PoT,
Low-Drift Digital Potentiometers in SOT23
ABSOLUTE MAXIMUM RATINGS
VDD to GND ............................................................. -0.3V to +6V
DIN, SCLK, CS to GND ............................................-0.3V to +6V
H, L, W to GND...........................................-0.3V to (VDD + 0.3V)
Maximum Continuous Current into
Pins H, L, and W ...........................................................±1mA
Continuous Power Dissipation (TA = +70°C)
8-Pin SOT23 (derate 8.7mW/°C above +70°C)...........697mW
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ..................................................…+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VDD = +5V, VH = VDD, VL = 0, TA = TMIN to TMAX. Typical values are at TA = +25°C, unless otherwise noted. Parameters are measured at TA = +25°C. Values over full temperature range are guaranteed by design.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DC PERFORMANCE (Voltage Divider Mode)
Resolution
N
8
Bits
Integral Nonlinearity
(Notes 1, 2)
INL
±1/2
LSB
Differential Nonlinearity
(Notes 1, 2)
DNL
±1/2
LSB
End-to-End Resistor Tempco
TCR
Ratiometric Resistor Tempco
Full-Scale Ratio Error
Zero-Scale Ratio Error
50
ppm/°C
5
ppm/°C
MAX5400
-0.8
MAX5401
-0.4
MAX5400
+0.8
MAX5401
+0.4
LSB
LSB
POWER SUPPLIES
Supply Voltage
VDD
Supply Current
IDD
2.7
CS = SCLK = DIN = VDD
VDD = 5V
0.7
VDD = 2.7V
0.1
5.5
V
5
µA
µA
DC PERFORMANCE (Variable Resistor Mode)
Resolution
Integral Nonlinearity
(Notes 1, 3)
Differential Nonlinearity
(Notes 1, 3)
N
8
Bits
±1
VCC = 5V
INL
DNL
VCC = 3V
MAX5400
±1.5
MAX5401
±1
VCC = 5V
±1/2
VCC = 3V
±1/2
LSB
LSB
DC PERFORMANCE (Resistor Characteristics)
Wiper Resistance (Note 4)
RW
250
Wiper Capacitance
CW
25
End-to-End Resistance
RHL
2
800
MAX5401
75
100
125
MAX5400
37.5
50
62.5
_______________________________________________________________________________________
Ω
pF
kΩ
256-Tap SOT-PoT,
Low-Drift Digital Potentiometers in SOT23
(VDD = +5V, VH = VDD, VL = 0, TA = TMIN to TMAX. Typical values are at TA = +25°C, unless otherwise noted. Parameters are measured at TA = +25°C. Values over full temperature range are guaranteed by design.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
DIGITAL INPUTS
Input High Voltage
VIH
VCC = 5V
Input Low Voltage
VIL
VCC = 5V
Input High Voltage
VIH
VCC = 3V
Input Low Voltage
VIL
VCC = 3V
0.7 ✕ VDD
V
0.3 ✕ VDD
0.7 ✕ VDD
V
0.3 ✕ VDD
±1.0
Input Leakage Current
Input Capacitance
V
5.0
V
µA
pF
TIMING CHARACTERISTICS (Voltage Divider Mode)
Wiper Settling Time
tIL
MAX5400 (to 50% of final value, from code 0
to code 128)
300
MAX5401 (to 50% of final value, from code 0
to code 128)
600
ns
TIMING CHARACTERISTICS (Digital) (Note 5)
SCLK Clock Period
tCP
100
ns
SCLK Pulse Width High
tCH
40
ns
SCLK Pulse Width Low
tCL
40
ns
CS Fall to SCLK Rise Setup
Time
tCSS
40
ns
SCLK Rise to CS Rise Hold Time
tCSH
0
ns
tDS
40
ns
DIN Setup Time
DIN Hold Time
tDH
0
ns
SCLK Rise to CS Fall Delay
tCS0
10
ns
CS Rise to SCLK Rise Hold
tCS1
40
ns
CS Pulse Width High
tCSW
100
ns
Note 1: Linearity is defined in terms of the H to L code-dependent resistance.
Note 2: The DNL and INL are measured with the potentiometer configured as a voltage-divider with H = VDD and L = 0. The wiper
terminal is unloaded and measured with an ideal voltmeter.
Note 3: The DNL and INL are measured with the potentiometer configured as a variable resistor. H is unconnected and L = 0. The
wiper terminal is driven with a source current of 80µA for the 50kΩ configuration and 40µA for the 100kΩ configuration.
Note 4: The wiper resistance is measured assuming the source currents given in Note 2.
Note 5: Digital timing is guaranteed by design.
_______________________________________________________________________________________
3
MAX5400/MAX5401
ELECTRICAL CHARACTERISTICS (continued)
Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
END-TO-END RESISTANCE % CHANGE
vs. TEMPERATURE
200
100
MAX5400toc02
50kΩ
-0.03
-0.05
-0.07
0
1
2
3
4
VARIABLE RESISTOR DNL
vs. INPUT CODE (50kΩ)
MAX5400 Toc04
0.020
0.015
(LSB)
30
25
20
15
5
0
96
0.15
0.10
0.005
0.05
0
-0.005
-0.05
-0.010
-0.10
-0.015
-0.15
-0.20
0
32
64
96
128 160 192 224 256
0
32
64
96
128 160 192 224 256
INPUT CODE-DECIMAL
VARIABLE RESISTOR DNL
vs. INPUT CODE (100kΩ)
VARIABLE RESISTOR INL
vs. INPUT CODE (100kΩ)
SUPPLY CURRENT
vs. TEMPERATURE
0.05
(LSB)
0.005
0
0
-0.005
-0.05
-0.010
-0.10
-0.015
-0.15
96
128 160 192 224 256
INPUT CODE-DECIMAL
0.6
0.4
VDD = +3V
0.2
0
-0.20
64
VDD = +5V
0.8
SUPPLY CURRENT (µA)
0.15
0.10
1.0
MAX5400 Toc08
MAX5400 Toc07
0.20
0.010
-1.020
4
0
INPUT CODE-DECIMAL
0.015
32
128 160 192 224 256
INPUT CODE-DECIMAL
0.020
0
96
0.20
0.010
128 160 192 224 256
64
VARIABLE RESISTOR INL vs. INPUT CODE
(50kΩ)
-0.020
64
32
INPUT CODE-DECIMAL
10
32
30
0
(LSB)
35
0
40
0
W-to-L RESISTANCE vs. INPUT CODE
(50kΩ)
40
50
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80
5
TEMPERATURE (°C)
VDD = 2.7V
to 5.5V
45
60
10
WIPER VOLTAGE (V)
50
70
20
-0.09
-0.11
0
W-TO-L RESISTANCE (kΩ)
-0.01
80
MAX5400 Toc06
VDD = +5V
100kΩ
0.01
VDD = 2.7V
to 5.5V
90
0
32
64
96
128 160 192 224 256
INPUT CODE-DECIMAL
-40 -30 -20 -10 0 10 20 30 40 50 60 70 80
TEMPERATURE (°C)
_______________________________________________________________________________________
MAX5400toc09
300
0.03
W-TO-L RESISTANCE (kΩ)
VDD = +3V
400
100
MAX5400 Toc05
WIPER RESISTANCE (Ω)
500
0.05
END-TO-END RESISTANCE % CHANGE
MAX5400 toc01
600
W-to-L RESISTANCE vs. INPUT CODE
(100kΩ)
MAX5400 Toc03
WIPER RESISTANCE vs. VOLTAGE
(LSB)
MAX5400/MAX5401
256-Tap SOT-PoT,
Low-Drift Digital Potentiometers in SOT23
256-Tap SOT-PoT,
Low-Drift Digital Potentiometers in SOT23
TAP-to-TAP SWITCHING TRANSIENT
(FROM CODE 127 toc CODE 128)
SUPPLY CURRENT vs.
INPUT LOGIC VOLTAGE
MAX5400 Toc10
MAX5400 Toc11
10
10mV/div
2.5V
5V/div
CS
0
SUPPLY CURRENT (mA)
1
VW-L
VDD = +5V
0.1
0.01
VDD = +3V
0.001
0.0001
0
1
2
3
4
5
DIGITAL INPUT VOLTAGE (V)
VOLTAGE DIVIDER DNL
vs. INPUT CODE (50kΩ)
0.08
0.06
VDD = +2.7V to +5.5V
0.15
0.10
0.04
0.05
(LSB)
0.02
(LSB)
MAX5400 Toc13
0.20
MAX5400 Toc12
0.10
VOLTAGE DIVIDER INL
vs. INPUT CODE (50kΩ)
0
-0.02
0
-0.05
-0.04
-0.10
-0.06
-0.15
-0.08
-0.10
-0.20
0
32
64
96
128 160 192 224 256
0
32
64
INPUT CODE-DECIMAL
96
128 160 192 224 256
INPUT CODE-DECIMAL
Pin Description
PIN
NAME
1
L
2
GND
FUNCTION
Low Terminal of Resistor
Ground
3
CS
Chip Select Input
4
DIN
Serial Data Input
5
SCLK
6
VDD
7
W
Wiper Terminal
8
H
High Terminal of Resistor
Clock Input
Power Supply. Bypass with a 0.1µF capacitor to GND.
_______________________________________________________________________________________
5
MAX5400/MAX5401
Typical Operating Characteristics (continued)
(TA = +25°C, unless otherwise noted.)
MAX5400/MAX5401
256-Tap SOT-PoT,
Low-Drift Digital Potentiometers in SOT23
POT REGISTER LOADED
CS
SCLK
8TH CLOCK PULSE
1ST CLOCK PULSE
DIN
D7
D6
D5
D4
D3
D2
D1
D0
LSB
MSB
TIME
Figure 2. Serial Interface Timing Diagram
CS
tCSW
tCSO
tCS1
tCSS
tCH
tCL
tCP
tCSH
SCLK
tDS
tDH
DIN
Figure 3. Detailed Serial Interface Timing Diagram
Detailed Description
The MAX5400/MAX5401 consists of 255 fixed resistors
in series between pins H and L. The potentiometer
wiper (pin W) can be programmed to access any one
of the 256 different tap points on the resistor string. The
MAX5400/MAX5401 uses a 3-wire serial data interface
to control the wiper tap position. This write-only interface contains three inputs: Chip-Select (CS), Data In
(DIN), and Data Clock (SCLK). When CS is taken low,
data from the DIN pin is synchronously loaded into the
8-bit serial shift register on the rising edge of each
SCLK pulse. The MSB is shifted in first as shown in
Figure 4. Note that if CS is not kept low during the entire
data stream, the data will be corrupted and the device
6
will need to be reloaded. After all 8 data bits have been
loaded into the shift register, they are latched into the
decoder once CS is taken high. The decoder switches
the potentiometer wiper to the tap position that corresponds to the 8-bit input data. Each resistor cell is
50kΩ/255 or 196.1Ω for the MAX5400 and 100kΩ/255
or 392.2Ω for the MAX5401.
The MAX5400/MAX5401 feature power-on reset (POR)
circuitry that sets the wiper to the midscale position at
power-up by loading a binary value of 128 into the 8-bit
latch.
The MAX5400/MAX5401 can be used as a variable
resistor by connecting pin W to either pin H or pin L.
_______________________________________________________________________________________
256-Tap SOT-PoT,
Low-Drift Digital Potentiometers in SOT23
B0 (D7)
B1 (D6)
B2 (D5)
B3 (D4)
B4 (D3)
B5 (D2)
B6 (D1)
(MSB)
FIRST
BIT IN
B7 (D0)
(LSB)
LAST
BIT IN
Figure 4. Serial Data Format
Applications Information
The MAX5400/MAX5401 are intended for a variety of
circuits that require accurate, fine-tuning adjustable
resistance, such as adjustable voltage or adjustable
gain circuit configurations. The MAX5400/MAX5401 are
primarily used in either a potentiometer divider or a
variable resistor configuration.
Adjustable Current-to-Voltage Converter
Figure 5 shows the MAX5400/MAX5401 being used
with a MAX4250 low-noise op amp to fine tune a current-to-voltage converter. Pins H and W of the
MAX5400/MAX5401 are connected to the node
between R3 and R2 and pin L is connected to ground.
resistor configuration so that the gain of the circuit can
be digitally controlled.
Adjustable Voltage Reference
In Figure 7, the MAX5400/MAX5401 are shown with the
MAX6160 to make an adjustable voltage reference. In
this circuit, the H pin of the MAX5400/MAX5401 is connected to the OUT pin of the MAX6160, the L pin of the
MAX5400/MAX5401 is connected to GND, and the W
pin of the MAX5400/MAX5401 is connected to the ADJ
pin of the MAX6160. The MAX5400/MAX5401 allow precise tuning of the voltage reference output. A low
5ppm/°C ratiometric tempco allows a very stable
adjustable voltage over temperature.
Adjustable Gain Amplifier
The MAX5400/MAX5401 are used again with the
MAX4250 to make a digitally adjustable gain circuit as
shown in Figure 6. The normal feedback resistor is
replaced with the MAX5400/MAX5401 in a variable
+5V
R3
VS
+5V
R1
VO
R2
VO
MAX4250
R2
MAX4250
R1
VO / IS = R3(1 + R2 / R1)+ R2
VO / VS = 1 + R2 / R1
Figure 5. I to V Converter
Figure 6. Noninverting Amplifier
_______________________________________________________________________________________
7
MAX5400/MAX5401
DATA WORD
MAX5400/MAX5401
256-Tap SOT-PoT,
Low-Drift Digital Potentiometers in SOT23
Chip Information
+5V
TRANSISTOR COUNT: 3769
TECHNOLOGY: BiCMOS
VIN
VO REF
OUT
MAX6160
ADJ
H
W
GND
L
VO = 1.23V × 100kΩ FOR MAX5401
R2(kΩ)
VO = 1.23V × 50kΩ FOR MAX5400
R2(kΩ)
Figure 7. Adjustable Voltage Reference
Pin Configuration
TOP VIEW
L 1
GND 2
CS
3
MAX5400/
MAX5401
DIN 4
8
H
7
W
6
VDD
5
SCLK
SOT23
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
8 _____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2000 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.
Similar pages