AD AD872AJE Complete 12-bit 10 msps monolithic a/d converter Datasheet

a
FEATURES
Monolithic 12-Bit 10 MSPS A/D Converter
Low Noise: 0.26 LSB RMS Referred-to-Input
No Missing Codes Guaranteed
Differential Nonlinearity Error: 0.5 LSB
Signal-to-Noise and Distortion Ratio: 68 dB
Spurious-Free Dynamic Range: 75 dB
Power Dissipation: 1.03 W
Complete: On-Chip Track-and-Hold Amplifier and
Voltage Reference
Twos Complement Binary Output Data
Out-of-Range Indicator
28-Lead Ceramic DIP or 44-Terminal Leadless Chip
Carrier Package
PRODUCT DESCRIPTION
The AD872A is a monolithic 12-bit, 10 MSPS analog-to-digital
converter with an on-chip, high performance track-and-hold
amplifier and voltage reference. The AD872A uses a multistage
differential pipelined architecture with error correction logic to
provide 12-bit accuracy at 10 MSPS data rates and guarantees
no missing codes over the full operating temperature range. The
AD872A is a redesigned version of the AD872 which has been
optimized for lower noise. The AD872A is pin compatible with
the AD872, allowing the parts to be used interchangeably as system requirements change.
The low noise input track-and-hold (T/H) of the AD872A is
ideally suited for high-end imaging applications. In addition, the
T/H’s high input impedance and fast settling characteristics allow the AD872A to easily interface with multiplexed systems
that switch multiple signals through a single A/D converter. The
dynamic performance of the T/H also renders the AD872A suitable for sampling single channel inputs at frequencies up to and
beyond the Nyquist rate. The AD872A provides both reference
output and reference input pins, allowing the onboard reference
to serve as a system reference. An external reference can also be
chosen to suit the dc accuracy and temperature drift requirements of the application. A single clock input is used to control
all internal conversion cycles. The digital output data is presented in twos complement binary output format. An out-ofrange signal indicates an overflow condition, and can be used
with the most significant bit to determine low or high overflow.
Complete 12-Bit 10 MSPS
Monolithic A/D Converter
AD872A
FUNCTIONAL BLOCK DIAGRAM
AVDD AGND AVSS
DVDD
DGND *DRVDD *DRGND
AD872A
VINA
VINB
+
T/H
DAC
A/D
CLOCK
+
T/H
DAC
A/D
4
+
T/H
DAC
A/D
4
A/D
3
4
CORRECTION LOGIC
REF IN
REF OUT
+2.5V
REFERENCE
OUTPUT BUFFERS
REF GND
OTR MSB *MSB
BIT2–BIT12
*OEN
*ONLY AVAILABLE ON 44-TERMINAL SURFACE MOUNT PACKAGE
The AD872A is fabricated on Analog Devices’ ABCMOS-l
process that utilizes high speed bipolar and CMOS transistors
on a single chip.
The AD872A is packaged in a 28-lead ceramic DIP and a 44terminal leadless ceramic surface mount package (LCC). Operation is specified from 0°C to +70°C and –55°C to +125°C.
PRODUCT HIGHLIGHTS
The AD872A offers a complete single-chip sampling, 12-bit
10 MSPS analog-to-digital conversion function in a 28-lead DIP
or 44-terminal LCC.
Low Noise—The AD872A features 0.26 LSB rms referred toinput noise.
Low Power—The AD872A at 1.03 W consumes a fraction of the
power of presently available hybrids.
On-Chip Track-and-Hold (T/H)—The low noise, high impedance T/H input eliminates the need for external buffers and can
be configured for single-ended or differential inputs.
Ease of Use—The AD872A is complete with T/H and voltage
reference and is pin-compatible with the AD872.
Out of Range (OTR)—The OTR output bit indicates when the
input signal is beyond the AD872A’s input range.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
World Wide Web Site: http://www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 1997
AD872A–SPECIFICATIONS
DC SPECIFICATIONS (T
MIN
to TMAX, AVDD = + 5 V, DV DD = +5 V, AVSS = –5 V, f SAMPLE = 10 MHz unless otherwise noted)
Parameter
J Grade1
S Grade1
Units
RESOLUTION
12
12
Bits min
MAX CONVERSION RATE
10
10
MHz min
INPUT REFERRED NOISE
0.26
0.26
LSB rms typ
ACCURACY
Integral Nonlinearity (INL)
Differential Nonlinearity (DNL)
No Missing Codes
Zero Error (@ +25°C)2
Gain Error (@ +25°C)2
± 1.75
± 0.5
12
± 0.75
± 1.25
± 1.75
± 0.5
12
± 0.75
± 1.25
LSB typ
LSB typ
Bits Guaranteed
% FSR max
% FSR max
TEMPERATURE DRIFT
Zero Error
Gain Error3, 4
Gain Error3, 5
± 0.15
± 0.80
± 0.25
± 0.3
± 1.75
± 0.50
% FSR max
% FSR max
% FSR max
POWER SUPPLY REJECTION6
AVDD , DVDD (+5 V ± 0.25 V)
AVSS (–5 V ± 0.25 V)
± 0.125
± 0.125
± 0.125
± 0.125
% FSR max
% FSR max
ANALOG INPUT
Input Range
Input Resistance
Input Capacitance
± 1.0
50
10
± 1.0
50
10
V max
kΩ typ
pF typ
INTERNAL VOLTAGE REFERENCE
Output Voltage
Output Voltage Tolerance
Output Current (Available for External Loads)
(External Load Should Not Change During Conversion)
2.5
± 20
2.0
2.5
± 40
2.0
V typ
mV max
mA typ
REFERENCE INPUT RESISTANCE
5
5
kΩ
+5
–5
+5
+5
+5
–5
+5
+5
V (± 5% AVDD Operating)
V (± 5% AVSS Operating)
V (± 5% DVDD Operating)
V (± 5% DRVDD Operating)
91
147
20
2
92
150
21
2
mA max (85 mA typ)
mA max (115 mA typ)
mA max (7 mA typ)
mA
1.03
1.25
1.03
1.3
W typ
W max
POWER SUPPLIES
Supply Voltages
AVDD
AVSS
DVDD
DRVDD 7
Supply Current
IAVDD
IAVSS
IDVDD
IDRVDD7
POWER CONSUMPTION
NOTES
1
Temperature ranges are as follows: J Grade: 0°C to +70°C, S Grade: –55°C to +125°C.
2
Adjustable to zero with external potentiometers (see Zero and Gain Error Calibration section).
3
+25°C to T MIN and +25°C to T MAX.
4
Includes internal voltage reference drift.
5
Excludes internal voltage reference drift.
6
Change in Gain Error as a function of the dc supply voltage (V NOMINAL to VMIN, VNOMINAL to VMAX ).
7
LCC package only.
Specifications subject to change without notice.
–2–
REV. A
AD872A
AC SPECIFICATIONS (T
MIN
to TMAX, AVDD = + 5 V, DV DD = +5 V, AVSS = –5 V, f SAMPLE = 10 MHz unless otherwise noted) 1
Parameter
J Grade
S Grade
Units
68
61
66
68
61
66
dB typ
dB min
dB typ
69
67
69
67
dB typ
dB typ
–74
–63
–72
–74
–62
–72
dB typ
dB max
dB typ
SPURIOUS-FREE DYNAMIC RANGE (SFDR)
fINPUT = l MHz
fINPUT = 4.99 MHz
75
74
75
74
dB typ
dB typ
INTERMODULATION DISTORTION (IMD)2
Second Order Products
Third Order Products
–80
–73
–80
–73
dB typ
dB typ
FULL POWER BANDWIDTH
35
35
MHz typ
SMALL SIGNAL BANDWIDTH
35
35
MHz typ
APERTURE DELAY
6
6
ns typ
APERTURE JITTER
16
16
ps rms typ
ACQUISITION TO FULL-SCALE STEP
40
40
ns typ
OVERVOLTAGE RECOVERY TIME
40
40
ns typ
SIGNAL-TO-NOISE & DISTORTION RATIO (S/N+D)
fINPUT = l MHz
fINPUT = 4.99 MHz
SIGNAL-TO-NOISE RATIO (SNR)
fINPUT = 1 MHz
fINPUT = 4.99 MHz
TOTAL HARMONIC DISTORTION (THD)
fINPUT = 1 MHz
fINPUT = 4.99 MHz
NOTES
1
f INPUT amplitude = –0.5 dB full scale unless otherwise indicated. All measurements referred to a 0 dB (1.0 V pk) input signal unless otherwise indicated.
2
fa = 1.0 MHz, fb = 0.95 MHz with t SAMPLE = 10 MHz.
Specifications subject to change without notice.
DIGITAL SPECIFICATIONS (T
MIN
to TMAX, AVDD = + 5 V, DV DD = +5 V, AVSS = –5 V, f SAMPLE = 10 MHz unless otherwise noted)
Parameter
Symbol
J, S Grades
Units
LOGIC INPUTS
High Level Input Voltage
Low Level Input Voltage
High Level Input Current (VIN = DVDD)
Low Level Input Current (VIN = 0 V)
Input Capacitance
VIH
VIL
IIH
IIL
CIN
+2.0
+0.8
115
115
5
V min
V max
µA max
µA max
pF typ
LOGIC OUTPUT
High Level Output Voltage (IOH = 0.5 mA)
Low Level Output Voltage (IOL = 1.6 mA)
Output Capacitance
Leakage (Three State, LCC Only)
VOH
VOL
COUT
IZ
+2.4
+0.4
5
± 10
V min
V max
pF typ
µA max
Specifications subject to change without notice.
REV. A
–3–
AD872A
(TMIN to TMAX with AV DD = +5 V, DVDD = +5 V, DRVDD = +5 V, AVSS = –5 V; VIL = 0.8 V,
IN = 2.0 V, V OL = 0.4 V and VOH = 2.4 V)
SWITCHING SPECIFICATIONS V
Parameter
Symbol
J, S Grades
Units
Clock Period
CLOCK Pulsewidth High
CLOCK Pulsewidth Low
Clock Duty Cycle2
tC
tCH
tCL
Output Delay
Pipeline Delay (Latency)
Data Access Time (LCC Package Only)2
Output Float Delay (LCC Package Only)2
tOD
100
45
45
40
60
10
3
50
50
ns min
ns min
ns min
% min (50% typ)
% max
ns min (20 ns typ)
Clock Cycles
ns typ (100 pF Load)
ns typ (10 pF Load)
1
tDD
tHL
NOTES
1
Conversion rate is operational down to 10 kHz without degradation in specified performance.
2
See section on Three-State Outputs for timing diagrams and applications information.
Specifications subject to change without notice.
N
N+1
VIN
tC
CLOCK
N+1
N
tCH
tCL
tOD
DATA
N
BIT 2–12
MSB, OTR
DATA
N+1
Figure 1. Timing Diagram
ABSOLUTE MAXIMUM RATINGS 1
Parameter
With Respect to
Min
Max
Units
AVDD
AVSS
DVDD, DRVDD2
DRVDD 2
DRGND
AGND
AVDD
Clock Input, OEN2
Digital Outputs
VINA, VINB, REF IN
REF IN
Junction Temperature
Storage Temperature
Lead Temperature (10 sec)
AGND
AGND
DGND, DRGND2
DVDD
DGND
DGND
DVDD
DGND
DGND
AGND
AGND
–0.5
–6.5
–0.5
–6.5
–0.3
–1.0
–6.5
–0.5
–0.5
–6.5
AV SS
+6.5
+0.5
+6.5
+6.5
+0.3
+1.0
+6.5
DVDD + 0.5
DVDD + 0.3
+6.5
AV DD
+150
+150
+300
Volts
Volts
Volts
Volts
Volts
Volts
Volts
Volts
Volts
Volts
Volts
°C
°C
°C
–65
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device
at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum ratings for extended
periods may affect device reliability.
2
LCC package only.
–4–
REV. A
AD872A
PIN DESCRIPTION
Symbol
DIP
LCC
Pin No. Pin No.
Type
Name and Function
VINA
1
1
AI
(+) Analog Input Signal on the differential input amplifier.
VINB
2
2
AI
(–) Analog Input Signal on the differential input amplifier.
AVSS
3, 25
5, 40
P
–5 V Analog Supply.
AVDD
4
6, 38
P
+5 V Analog Supply.
AGND
5, 24
9, 36
P
Analog Ground.
DGND
6, 23
10
P
Digital Ground.
DVDD
7, 22
33
P
+5 V Digital Supply.
BIT 12 (LSB)
8
16
DO
Least Significant Bit.
BIT 2–BIT 11
18–9
26–17
DO
Data Bits 2 through 11.
MSB
19
29
DO
Inverted Most Significant Bit. Provides twos complement output
data format.
OTR
20
30
DO
Out of Range is Active HIGH on the leading edge of Code 0 or the
trailing edge of Code 4096. See Output Data Format Table III.
CLK
21
31
DI
Clock Input. The AD872A will initiate a conversion on the rising
edge of the clock input. See the Timing Diagram for details.
REF OUT
26
41
AO
+2.5 V Reference Output. Tie to REF IN for normal operation.
REF GND
27
42
AI
Reference Ground.
REF IN
28
43
AI
Reference Input. +2.5 V input gives ± 1 V full-scale range.
P
DRVDD
N/A
12, 32
NC
N/A
DRGND
N/A
3, 4, 7, 8, 14, 15,
28, 35, 37, 39, 44
11, 34
+5 V Digital Supply for the output drivers.
P
Digital Ground for the output drivers. (See section on Power Supply
Decoupling for details on DRVDD and DRGND.)
OEN
N/A
13
DI
Output Enable. See the Three State Output Timing Diagram for details.
BIT 1
N/A
27
DO
Most Significant Bit.
No Connect.
TYPE: AI = Analog Input; AO = Analog Output; DI = Digital Input; DO = Digital Output; P = Power; N/A = Not Available on 28-lead DIP. Only available on
44-terminal surface mount package.
PIN CONFIGURATIONS
43
AVSS
44
REF GND
1
REF OUT
REF IN
2
42
41
40
AVSS
3
26 REF OUT
NC 7
39
NC
AVDD
4
25 AVSS
NC 8
38
AVDD
AGND 5
DGND 6
AD872A
24 AGND
AGND
9
37
NC
23 DGND
DGND 10
36
AGND
TOP VIEW
DVDD 7 (Not to Scale) 22 DVDD
DRGND 11
AD872A
35
NC
34
DRGND
BIT 12 (LSB) 8
21 CLK
DRVDD 12
BIT 11 9
20 OTR
OEN 13
33
DVDD
BIT 10 10
19 MSB
NC 14
32
DRVDD
BIT 9 11
18 BIT 2
NC 15
31
CLK
BIT 8 12
17 BIT 3
BIT 12 (LSB) 16
30
OTR
BIT 7 13
16 BIT 4
BIT 11 17
29
MSB
18
19
20
21
22
23
24
25
26
27
28
BIT 9
BIT 8
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1 (MSB)
NC
15 BIT 5
TOP VIEW
(NOT TO SCALE)
BIT 10
BIT 6 14
NC = NO CONNECT
REV. A
3
VINA
4
NC
5
NC
6
VINB
27 REF GND
NC
28 REF IN
VINB 2
AVDD
VINA 1
44-Terminal LCC
AVSS
28-Lead Ceramic DIP
–5–
AD872A
DEFINITIONS OF SPECIFICATIONS
OVERVOLTAGE RECOVERY TIME
LINEARITY ERROR (INL)
Overvoltage recovery time is defined as that amount of time required for the ADC to achieve a specified accuracy after an
overvoltage (50% greater than full-scale range), measured from
the time the overvoltage signal reenters the converter’s range.
Linearity error refers to the deviation of each individual code
from a line drawn from “negative full scale” through “positive
full scale.” The point used as “negative full scale” occurs
1/2 LSB before the first code transition. “Positive full scale” is
defined as a level 1 1/2 LSB beyond the last code transition.
The deviation is measured from the middle of each particular
code to the true straight line.
DYNAMIC SPECIFICATIONS
SIGNAL-TO-NOISE AND DISTORTION (S/N+D) RATIO
S/N+D is the ratio of the rms value of the measured input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/N+D is expressed in decibels.
DIFFERENTIAL LINEARITY ERROR (DNL, NO MISSING
CODES)
An ideal ADC exhibits code transitions that are exactly 1 LSB
apart. DNL is the deviation from this ideal value. Guaranteed
no missing codes to 12-bit resolution indicates that all 4096
codes must be present over all operating ranges.
TOTAL HARMONIC DISTORTION (THD)
THD is the ratio of the rms sum of the first six harmonic components to the rms value of the measured input signal and is expressed as a percentage or in decibels.
ZERO ERROR
INTERMODULATION DISTORTION (IMD)
The major carry transition should occur for an analog value
1/2 LSB below analog common. Zero error is defined as the
deviation of the actual transition from that point. The zero error
and temperature drift specify the initial deviation and maximum
change in the zero error over temperature.
The first code transition should occur for an analog value
1/2 LSB above nominal negative full scale. The last transition
should occur for an analog value 1 1/2 LSB below the nominal
positive full scale. Gain error is the deviation of the actual difference between first and last code transitions and the ideal difference between first and last code transitions.
With inputs consisting of sine waves at two frequencies, fa and
fb, any device with nonlinearities will create distortion products,
of order (m + n), at sum and difference frequencies of mfa ±
nfb, where m, n = 0, 1, 2, 3 . . . . Intermodulation terms are
those for which m or n is not equal to zero. For example, the
second order terms are (fa + fb) and (fa – fb), and the third order terms are (2 fa + fb), (2 fa – fb), (fa + 2 fb) and (2 fb – fa).
The IMD products are expressed as the decibel ratio of the rms
sum of the measured input signals to the rms sum of the distortion terms. The two signals are of equal amplitude and the peak
value of their sums is –0.5 dB from full scale. The IMD products are normalized to a 0 dB input signal.
TEMPERATURE DRIFT
FULL-POWER BANDWIDTH
The temperature drift for zero error and gain error specifies the
maximum change from the initial (+25°C) value to the value at
TMIN or TMAX.
The full-power bandwidth is that input frequency at which the
amplitude of the reconstructed fundamental is reduced by 3 dB
for a full-scale input.
POWER SUPPLY REJECTION
SPURIOUS FREE DYNAMIC RANGE
GAIN ERROR
The difference, in dB, between the rms amplitude of the input
signal and the peak spurious signal.
The specifications show the maximum change in the converter’s
full scale as the supplies are varied from nominal to min/max
values.
ORDERING GUIDE
APERTURE JITTER
Aperture jitter is the variation in aperture delay for successive
samples and is manifested as noise on the input to the A/D.
APERTURE DELAY
Aperture delay is a measure of the Track-and-Hold Amplifier
(THA) performance and is measured from the rising edge of the
clock input to when the input signal is held for conversion.
Model
Temperature Range
Package Option1
AD872AJD
AD872AJE
AD872ASD2
AD872ASE2
0°C to +70°C
0°C to +70°C
–55°C to +125°C
–55°C to +125°C
D-28
E-44A
D-28
E-44A
NOTES
1
D = Ceramic DIP, E = Leadless Ceramic Chip Carrier.
2
MIL-STD-883 version will be available; contact factory.
–6–
REV. A
Dynamic Characteristics–Sample Rate: 10 MSPS–AD872A
–70
70
THD
68
–0.5 dB
–75
66
62
AMPLITUDE – dB
S/(N+D) – dB
64
–6.0 dB
60
58
2ND
HARMONIC
–80
–85
56
3RD
HARMONIC
–90
54
52
50
105
106
INPUT FREQUENCY – Hz
–95
105
107
Figure 2. AD872A S/(N+D) Input Frequency
106
INPUT FREQUENCY – Hz
107
Figure 3. AD872A Distortion vs. Input Frequency,
Full-Scale Input
1
HARMONICS – dB
2ND
–73
3RD
–82
4TH
–87
5TH
–90
6TH
–92
7TH
–95
8TH
–95
9TH
–93
15dB/ DIV
f IN = 1MHz
f IN AMPLITUDE = –0.5dB
THD = 73dB
S/(N+D) = 68dB
SNR = 70dB
SFDR = 73dB
2
3
4
9
7
8
5
6
Figure 4. AD872A Typical FFT, fIN = 1 MHz, fIN Amplitude = –0.5 dB
1
HARMONICS – dB
2ND
–81
3RD
–97
4TH
–91
5TH
–84
6TH
–88
7TH
–90
8TH
–90
9TH
–94
15dB/ DIV
f IN = 1MHz
f IN AMPLITUDE = –6.0dB
THD = –77dB
S/(N+D) = 65dB
SNR = 65dB
SFDR = 81dB
2
9
5
7
8
3
4
6
Figure 5. AD872A Typical FFT, fIN = 1 MHz, fIN Amplitude = –6 dB
REV. A
–7–
AD872A–Dynamic Characteristics–Sample Rate: 10 MSPS
1
HARMONICS – dB
2ND
–75
3RD
–88
4TH
–93
5TH
–87
6TH
–86
7TH
–90
8TH
–91
9TH
–94
15dB/ DIV
f IN = 750kHz
f IN AMPLITUDE = –0.5dB
THD = –74dB
S/(N+D) = 69dB
SNR = 71dB
SFDR = 75dB
2
3
5
4
9
6
8
7
Figure 6. AD872A Typical FFT, fIN = 750 kHz
1
HARMONICS – dB
2ND
–75
3RD
–93
4TH
–85
5TH
–85
6TH
–89
7TH
–97
8TH
–90
9TH
–92
15dB/ DIV
f IN = 5MHz
f IN AMPLITUDE = –0.5dB
THD = –74dB
S/(N+D) = 65dB
SNR = 65dB
SFDR = 69dB
2
5
4
9
Figure 7. AD872A Typical FFT, fIN = 5 MHz
100
700000
618061
90
80
500000
100 x p(≥ CODE X + 1)
NUMBER OF CODE HITS
600000
400000
300000
200000
70
60
50
0.26 LSB RMS
40
30
20
100000
19559
0
–1
10
15170
0
0
+1
CODE X
CODE X + 1
DEVIATION FROM CORRECT CODE – LSB
Figure 9. AD872A Code Probability at a Transition
Figure 8. AD872A Output Code Histogram for DC Input
–8–
REV. A
AD872A
The AD872A is implemented using a 4-stage pipelined multiple
flash architecture. A differential input track-and-hold amplifier
(THA) acquires the input and converts the input voltage into a
differential current. A 4-bit approximation of the input is made
by the first flash converter, and an accurate analog representation of this 4-bit guess is generated by a digital-to-analog converter. This approximation is subtracted from the THA output
to produce a remainder, or residue. This residue is then sampled and held by the second THA, and a 4-bit approximation is
generated and subtracted by the second stage. Once the second
THA goes into hold, the first stage goes back into track to
acquire a new input signal. The third stage provides a 3-bit approximation/subtraction operation, and produces the final residue, which is passed to a final 4-bit flash converter. The 15
output bits from the 4 flash converters are accumulated in the
correction logic block, which adds the bits together using the
appropriate correction algorithm, to produce the 12-bit output
word. The digital output, together with overrange indicator, is
latched into an output buffer to drive the output pins.
The additional THA inserted in each stage of the AD872A
architecture allows pipelining of the conversion. In essence, the
converter is converting multiple inputs simultaneously, processing them through the converter chain serially. This means that
while the converter is capable of capturing a new input sample
every clock cycle, it actually takes three clock cycles for the conversion to be fully processed and appear at the output. This
“pipeline delay” is often referred to as latency, and is not a concern in most applications, however there are some cases where it
may be a consideration. For example, some applications call for
the A/D converter to be placed in a high speed feedback loop,
where its input is servoed to provide a desired result at the digital output (e.g., offset calibration or zero restoration in video
applications). In these cases the three clock cycle delay through
the pipeline must be accounted for in the loop stability calculations. Also, because the converter is working on three conversions simultaneously, major disruptions to the part (such as a
large glitch on the supplies or reference) may corrupt three data
samples. Finally, there will be a minimum clock rate below
which the THA droop corrupts the signal in the pipeline. In the
case of the AD872A, this minimum clock rate is 10 kHz.
The high impedance differential inputs of the AD872A allow a
variety of input configurations (see APPLYING THE AD872A),
The AD872A converts the voltage difference between the VINA
and VINB pins. For single-ended applications, one input pin
(VINA or VINB) may be grounded, but even in this case the differential input can provide a performance boost: for example, for
an input coming from a coaxial cable, VINB can be tied to the
shield ground, allowing the AD872A to reject shield noise as
common mode. The high input impedance of the device minimizes external driving requirements and allows the user to externally select the appropriate termination impedance for the
application.
The AD872A clock circuitry uses both edges of the clock in its
internal timing circuitry (see spec page for exact timing requirements). The AD872A samples the analog input on the rising
edge of the clock input. During the clock low time (between the
falling edge and rising edge of the clock) the input THA is in
track mode; during the clock high time it is in hold. System disturbances just prior to the rising edge of the clock may cause the
part to acquire the wrong value, and should be minimized.
REV. A
While the part uses both clock edges for its timing, jitter is only
a significant issue for the rising edge of the clock (see CLOCK
INPUT section).
APPLYING THE AD872A ANALOG INPUTS
The AD872A features a high impedance differential input that
can readily operate on either single-ended or differential input
signals. Table I summarizes the nominal input voltage span for
both single-ended and differential modes, assuming a 2.5 V
reference input.
Table I. Input Voltage Span
Single-Ended
Differential
VINA
VINB
VINA–VINB
+1 V
–1 V
+0.5 V
–0.5 V
GND
GND
–0.5 V
+0.5 V
+1 V (Positive Full Scale)
–1 V (Negative Full Scale)
+1 V (Positive Full Scale)
–1 V (Negative Full Scale)
Figure 10 shows an approximate model for the analog input circuit. As this model indicates, when the input exceeds 1.6 V
(with respect to AGND), the input device may saturate, causing
the input impedance to drop substantially and significantly reducing the performance of the part. Input compliance in the
negative direction is somewhat larger, showing virtually no degradation in performance for inputs as low as –1.9 V.
+5V
1.75mA
VINA OR VINB
61V
+1.6V
5pF
AD872A
–1.9V
1.75mA
–5V
Figure 10. AD872A Equivalent Analog Input Circuit
Figure 11 illustrates the effect of varying the common-mode
voltage of a –0.5 dB input signal on total harmonic distortion.
0
–10
–20
–30
THD – dB
THEORY OF OPERATION
–40
–50
–60
–70
–80
–90
–100
–1
–0.8
–0.6 –0.4
–0.2
0
0.2
0.4
0.6
0.8
1.0
CM INPUT VOLTAGE – V
Figure 11. AD872A Total Harmonic Distortion vs. CM Input
Voltage, fIN = 1 MHz, FS = 10 MSPS
–9–
AD872A
Figure 12 shows the common-mode rejection performance vs.
frequency for a 1 V p-p common-mode input. This excellent
common-mode rejection over a wide bandwidth affords the user
the opportunity to eliminate many potential sources of input
noise as common mode by using the differential input structure
of the AD872A.
562V
562V
U1
VIN
VINA
AD872A
536V
(60.5V)
536V
–20
VINB
U2
–30
CMR – dB
–40
Figure 15. Single-Ended to Differential Connections; U1,
U2 = AD811 or AD9617
–50
The use of the differential input signal can help to minimize
even-order distortion from the input THA where performance
beyond –70 dB is desired.
–60
–70
Figure 16 shows the AD872A large signal (–0.5 dB) and small
signal (–20 dB) frequency response.
–80
–90
10
–100
105
106
107
108
0
INPUT FREQUENCY – Hz
FUND AMP – dB
Figure 12. Common-Mode Rejection vs. Input Frequency,
1 V p-p Input
Figures 13 and 14 illustrate typical input connections for singleended inputs.
61V
1
–10
–20
–30
VINA
–40
AD872A
2 VINB
–50
104
105
106
107
108
INPUT FREQUENCY – Hz
Figure 13. AD872A Single-Ended Input Connection
61V
1
RT
Figure 16. Full Power (–0.5 dB) and Small Signal
Response (–20 dB) vs. Input Frequency
The AD872A’s wide input bandwidth facilitates rapid acquisition of transient input signals: the input THA can typically settle
to 12-bit accuracy from a full-scale input step in less than 40 ns.
Figure 17 illustrates the typical acquisition of a full-scale input
step.
VINA
AD872A
2
VINB
Figure 14. AD872A Single-Ended Input Connection Using
a Shielded Cable
4500
The cable shield is used as a ground connection for the VINB input, providing the best possible rejection of the cable noise from
the input signal. Note also that the high input impedance of the
AD872A allows the user to select the termination impedance, be
it 50 ohms, or some other value. Furthermore, unlike many
flash converters, most AD872A applications will not require an
external buffer amplifier. If such an amplifier is required, we
suggest either the AD811 or AD9617.
3500
Figure 15 illustrates how external amplifiers may be used to
convert a single-ended input into a differential signal. The resistor values of 536 Ω and 562 Ω were selected to provide optimum phase matching between U1 and U2.
CODE OUT
4000
3000
2500
2000
1500
1000
500
0
0
10
20
30
40
nsec
50
60
70
80
Figure 17. Typical AD872A Settling Time
–10–
REV. A
AD872A
The wide input bandwidth and superior dynamic performance
of the input THA make the AD872A suitable for undersampling applications where the input frequency exceeds half the
sample frequency. The input THA is designed to recover rapidly from input overdrive conditions, returning from a 50%
overdrive in less than 40 ns.
The AD872A’s reference input impedance is equal to 5 kΩ
(± 20%), and its effective noise bandwidth is 10 MHz, with a
referred-to-input noise gain of 0.8. For example, the internal
reference, with an rms noise of 28 µV (using an external 1 µF
capacitor), contributes 24 µV (0.05 LSB) of noise to the transfer
function of the AD872A.
Because of the THA’s exceptionally wide input bandwidth,
some users may find the AD872A is sensitive to noise at frequencies from 10 MHz to 50 MHz that other converters are
incapable of responding to. This sensitivity can be mitigated by
careful use of the differential inputs (see previous paragraphs).
Additionally, Figure 18 shows how a small capacitor (10 pF20 pF for 50 Ω terminated inputs) may be placed between VINA
and VINB to help reduce high frequency noise in applications
where limiting the input bandwidth is acceptable.
The full-scale peak-to-peak input voltage is a function of the
reference voltage, according to the equation:
61V
1
(VINA = VINB ) Full Scale = 0.8 × (VREF – REF GND )
Note that the AD872A’s performance was optimized for a 2.5 V
reference input: performance may degrade somewhat for other
reference voltages. Figure 20 illustrates the S/(N+D) performance vs. reference voltage for a 1 MHz, –0.5 dB input signal.
Note also that if the reference is changed during a conversion,
all three conversions in the pipeline will be invalidated.
VINA
75
AD872A
10 OR 20pF
70
VINB
S/(N+D) – dB
2
Figure 18. Optional High Frequency Noise Reduction
The AD872A will contribute its own wideband thermal noise.
As a result of the integrated wideband noise (0.26 LSB rms,
referred-to-input), applying a dc analog input may produce
more than one code at the output. A histogram of the ADC
output codes, for a dc input voltage, will be between one and
three codes wide, depending on how well the input is centered
on a given code and how many samples are taken. Figure 8
shows a typical AD872A code histogram, and Figure 9 illustrates the AD872A’s transition noise.
50
1.5
1.9
2.1
2.3
2.5
2.7
2.9
3.1
3.3
3.5
Figure 20. S/(N+D) vs. Reference Input Voltage,
fIN = 1 MHz, FS = 10 MHz
AD872A
Table II summarizes various 2.5 V references suitable for use
with the AD872A, including the onboard bandgap reference
(see REFERENCE OUTPUT section).
Table II. Suitable 2.5 V References
REF43B
AD680JN
Internal
1
5kV
(620%)
Drift (ppm/8C)
Initial Accuracy %
6 (max)
10 (max)
30 (typ)
0.2
0.4
0.4
If an external reference is connected to REF IN, REF OUT
must be connected to +5 V. This should lower the current in
REF GND to less than 350 µA and eliminate the need for a
1 µF capacitor, although decoupling the reference for noise
reduction purposes is recommended.
2
AVSS
Figure 19. Equivalent Reference Input Circuit
However, in order to realize the lowest noise performance of the
AD872A, care should be taken to minimize noise at the reference input.
REV. A
1.7
REFERENCE INPUT VOLTAGE – V
The nominal reference input should be 2.5 V, taken with respect to REFERENCE GROUND (REF GND). Figure 19 illustrates the equivalent model for the reference input: there is
no clock or signal-dependent activity associated with the reference input circuitry, therefore, no “kickback” into the reference.
REF GND
60
55
REFERENCE INPUT
REF IN
65
Alternatively, Figure 21 shows how the AD872A may be driven
from other references by use of an external resistor. The external resistor forms a resistor divider with the on-chip 5 kΩ resistor to realize 2.5 V at the reference input pin (REF IN). A trim
potentiometer is needed to accommodate the tolerance of the
AD872A’s 5 kΩ resistor.
–11–
AD872A
2.55
2.54
2.5V
R
+5V REF
2kV
AD872A
REFERENCE VOLTAGE – Volts
RT
REF IN
3.9kV
5kV
REF GND
Figure 21. Optional +5 V Reference Input Circuit
2.53
2.52
2.51
2.50
2.49
2.48
2.47
2.46
REFERENCE GROUND
2.45
–55
The REF GND pin provides the reference point for both the
reference input, and the reference output. When the internal
reference is operating, it will draw approximately 500 µA of current through the reference ground, so a low impedance path to
the external common is desirable. The AD872A can tolerate a
fairly large difference between REF GND and AGND, up to
+1 V, without any performance degradation.
–35
–15
5
25
45
65
85
105
125
TEMPERATURE – 8C
Figure 23. Reference Output Voltage vs. Temperature
2.50
2.48
REFERENCE VOLTAGE – V
REFERENCE OUTPUT
The AD872A features an onboard, curvature compensated
bandgap reference that has been laser trimmed for both absolute
value and temperature drift. The output stage of the reference
was designed to allow the use of an external capacitor to limit
the wideband noise. As Figure 22 illustrates, a 1 µF capacitor on
the reference output is required for stability of the reference output
buffer. Note: If used, an external reference may become unstable
with this capacitor in place.
2.46
2.44
2.42
2.40
1k
REF IN
10k
100k
REFERENCE OUTPUT LOAD – V
1M
Figure 24. Reference Output Voltage vs. Output Load
AD872A
0.1mF
DIGITAL OUTPUTS
In 28-lead packages, the AD872A output data is presented in
twos complement format. Table III indicates offset binary and
twos complement output for various analog inputs.
REF GND
1.0mF
+
Table III. Output Data Format
REF OUT
Analog Input
Digital Output
VINA–VINB
Offset Binary
Twos Complement OTR
With this capacitor in place, the noise on the reference output is
approximately 28 µV rms at room temperature. Figure 23 shows
the typical temperature drift performance of the reference, while
Figure 24 illustrates the variation in reference voltage with load
currents.
≥0.999756 V
0.999268 V
0V
–1 V
–1.000244 V
1111 1111 1111
1111 1111 1111
1000 0000 0000
0000 0000 0000
0000 0000 0000
0111 1111 1111
0111 1111 1111
0000 0000 0000
1000 0000 0000
1000 0000 0000
The output stage is designed to provide at least 2 mA of output current, allowing a single reference to drive up to four
AD872As, or other external loads. The power supply rejection
of the reference is better than –54 dB at dc.
Users requiring offset binary encoding may simply invert the
MSB pin. In the 44-terminal surface mount packages, both
MSB and MSB bits are provided.
Figure 22. Typical Reference Decoupling Connection
1
0
0
0
1
The AD872A features a digital out-of-range (OTR) bit that goes
high when the input exceeds positive full scale or falls below
negative full scale. As Table III indicates, the output bits will be
set appropriately according to whether it is an out-of-range high
–12–
REV. A
AD872A
condition or an out-of-range low condition. Note that if the input is driven beyond +1.5 V, the digital outputs may not stay at
+FS, but may actually fold back to midscale.
In this case, a 20 MHz clock is divided by 2 to produce the
10 MHz clock input for the AD872A. In this configuration, the
duty cycle of the 20 MHz clock is irrelevant.
The AD872A’s CMOS digital output drivers are sized to provide sufficient output current to drive a wide variety of logic
families. However, large drive currents tend to cause glitches on
the supplies and may affect S/(N+D) performance. Applications
requiring the AD872A to drive large capacitive loads or large
fanout may require additional decoupling capacitors on DRVDD
and DVDD. In extreme cases, external buffers or latches could
be used.
The input circuitry for the CLKIN pin is designed to accommodate both TTL and CMOS inputs. The quality of the logic
input, particularly the rising edge, is critical in realizing the best
possible jitter performance for the part: the faster the rising
edge, the better the jitter performance.
THREE-STATE OUTPUTS
The 44-terminal surface mount AD872A offers three-state outputs. The digital outputs can be placed into a three-state mode
by pulling the OUTPUT ENABLE (OEN) pin LOW. Note that
this function is not intended to be used to pull the AD872A on
and off a bus at 10 MHz. Rather, it is intended to allow the ADC
to be pulled off the bus for evaluation or test modes. Also, to
avoid corruption of the sampled analog signal during conversion
(3 clock cycles), it is highly recommended that the AD872A be
placed on the bus prior to the first sampling.
As a result, careful selection of the logic family for the clock
driver, as well as the fanout and capacitive load on the clock
line, is important. Jitter-induced errors become more pronounced at higher frequency, large amplitude inputs, where the
input slew rate is greatest.
The AD872A is designed to support a sampling rate of 10
MSPS; running at slightly faster clock rates may be possible,
although at reduced performance levels. Conversely, some slight
performance improvements might be realized by clocking the
AD872A at slower clock rates. Figure 27 presents the S/(N+D)
vs. clock frequency for a 1 MHz analog input.
75
70
OEN
DATA
OUTPUT
tHL
S/(N+D) – dB
tDD
ACTIVE
THREE-STATE
65
60
Figure 25. Three-State Output Timing Diagram
For timing budgetary purposes, the typical access and float delay times for the AD872A are 50 ns.
55
CLOCK INPUT
50
The AD872A internal timing control uses the two edges of the
clock input to generate a variety of internal timing signals. The
optimal clock input should have a 50% duty cycle; however,
sensitivity to duty cycle is significantly reduced for clock rates of
less than 10 megasamples per second.
+5V
D
R
0
6
8
10
12
14
16
18
20
Figure 27. Typical S/(N+D) vs. Clock Frequency,
fIN = 1 MHz, Full-Scale Input
The power dissipated by the correction logic and output buffers
is largely proportional to the clock frequency; running at reduced clock rates provides a slight reduction in power consumption. Figure 28 illustrates this tradeoff.
1.09
Q
1.08
Q
CLK
POWER – W
S
4
FREQUENCY – MHz
74XX74
20MHz
2
+5V
Figure 26. Divide-by-Two Clock Circuit
1.07
1.06
1.05
Due to the nature of on-chip compensation circuitry, the duty
cycle should be maintained between 40% and 60% even for
clock rates less than 10 MSPS. One way to realize a 50% duty
cycle clock is to divide down a clock of higher frequency, as
shown in Figure 26.
1.04
0
2
4
6
8
10
12
14
16
18
20
FREQUENCY – MHz
Figure 28. Typical Power Dissipation vs. Clock Frequency
REV. A
–13–
AD872A
ANALOG SUPPLIES AND GROUNDS
DIGITAL SUPPLIES AND GROUNDS
The AD872A features separate analog and digital supply and
ground pins, helping to minimize digital corruption of sensitive
analog signals. In general, AVSS and AVDD, the analog supplies,
should be decoupled to AGND, the analog common, as close to
the chip as physically possible. Care has been taken to minimize
the signal dependence of the power supply currents; however,
the analog supply currents will be proportional to the reference
input. With REFIN at 2.5 V, the typical current into AVDD is
85 mA, while the typical current out of AVSS is 115 mA. Typically, 30 mA will flow into the AGND pin.
AVSS
The digital activity on the AD872A chip falls into two general
categories: CMOS correction logic, and CMOS output drivers.
The internal correction logic draws relatively small surges of
current, mainly during the clock transitions; in the 44-terminal
package, these currents flow through pins DGND and DVDD.
The output drivers draw large current impulses while the output
bits are changing. The size and duration of these currents are a
function of the load on the output bits: large capacitive loads are
to be avoided. In the 44-terminal package, the output drivers are
supplied through dedicated pins DRGND and DRVDD. Pin
count constraints in the 28-lead packages require that the digital
and driver supplies share package pins (although they have separate bond wires and on-chip routing). The decoupling shown in
Figure 34 is appropriate for a reasonable capacitive load on the
digital outputs (typically 20 pF on each pin). Applications
involving greater digital loads should consider increasing the
digital decoupling proportionately, and/or using external buffers/
latches.
AVDD
APPLICATIONS
OPTIONAL ZERO AND GAIN TRIM
Careful design and the use of differential circuitry provide the
AD872A with excellent rejection of power supply noise over a
wide range of frequencies, as illustrated in Figure 29.
–75
SUPPLY REJECTION – dB
–80
–85
The AD872A is factory trimmed to minimize zero error, gain
error and linearity errors. In some applications the zero and gain
errors of the AD872A need to be externally adjusted to zero. If
required, both zero error and gain error can be trimmed with external potentiometers as shown in Figure 31. Note that gain error adjustments must be made with an external reference.
–90
DVDD
–95
–100
104
105
106
FREQUENCY – Hz
Zero trim should be adjusted first. Connect VINA to ground and
adjust the 10 kΩ potentiometer such that a nominal digital output code of 0000 0000 0000 (twos complement output) exists.
Note that the zero trim should be decoupled and that the accuracy of the ± 2.5 V reference signals will directly affect the offset.
107
Figure 29. Power Supply Rejection vs. Frequency,
100 mV p-p Signal on Power Supplies
Figure 30 shows the degradation in SNR resulting from 100 mV
of power supply ripple at various frequencies. As Figure 30
shows, careful decoupling is required to realize the specified dynamic performance. Figure 34 demonstrates the recommended
decoupling strategy for the supply pins. Note that in extremely
noisy environments, a more elaborate supply filtering scheme
may be necessary.
Gain error may then be calibrated by adjusting the REF IN
voltage. The REF IN voltage should be adjusted such that a
+1 V input on VINA results in the digital output code 01111
1111 1111 (twos complement output).
AD872A
+2.5V
AD872A
VOUT
70
DVDD
10kV
V INB
10mF
0.1mF
65
TRIM
SNR – dB
AVSS
60
100kV
–2.5V
AVDD
(a) ZERO TRIM
55
(b) GAIN TRIM
Figure 31. Zero and Gain Error Trims
DIGITAL OFFSET CORRECTION
50
104
REF IN
REF43
105
106
FREQUENCY – Hz
Figure 30. SNR vs. Supply Noise Frequency
(fIN = 1 MHz)
107
The AD872A provides differential inputs that may be used to
correct any offset voltages on the analog input. For applications
where the input signal contains a dc offset, it may be advantageous to apply a nulling voltage to the VINB input. Applying a
voltage equal to the dc offset will maximize the full-scale input
range and therefore the dynamic range. Offsets ranging from
–0.7 V to +0.5 V can be corrected.
–14–
REV. A
AD872A
Figure 32 shows how a dc offset can be applied using the
AD568 12-bit, high speed digital-to-analog converter (DAC).
This circuit can be used for applications requiring offset adjustments on every clock cycle. The AD568 connection scheme is
used to provide a –0.512 V to +0.512 V output range. The offset voltage must be stable on the rising edge of the AD872A
clock input.
VIN
1
In order to maximize the spurious free dynamic range of the
circuit in Figure 33 it is advantageous to present a small signal
to the input of the AD9100 and then amplify the output to the
AD872A’s full-scale input range. This can be accomplished with
a low distortion, wide bandwidth amplifier such as the AD9617.
The circuit uses a gain of 3.5 to optimize S/(N+D).
For small scale input signals (–20 dB, –40 dB), the AD872A
performs better without the track-and-hold because slewlimiting effects are no longer dominant. To gain the advantages
of the added track-and-hold, it is important to give the AD872A
a full-scale input.
VINA
AD872A
8
DIGITAL
OFFSET
WORD
4
74
HC
574
AD568
8
74
HC
574
2
IBPO
IOUT
RL
ACOM
LCOM
REF COM
4
An alternative to the configuration presented above is to use the
AD9101 track-and-hold amplifier. The AD9101 provides a
built-in post amplifier with a gain of 4, providing excellent ac
characteristics in conjunction with a high level of integration.
VINB
As illustrated in Figure 33, it is necessary to skew the AD872A
sample clock and the AD9100 sample/hold control. Clock skew
(tS) is defined as the time starting at the AD9100’s transition
into hold mode and ending at the moment the AD872A samples.
The AD872A samples on the rising edge of the sample clock,
and the AD9100 samples on the falling edge of the sample/hold
control. The choice of tS is primarily determined by the settling
time of the AD9100. The droop rate of the AD9100 must also
be taken into consideration. Using these values, the ideal tS is
17 ns. When choosing clock sources, it is extremely important
that the front end track-and-hold sample/hold control is given a
very low jitter clock source. This is not as crucial for the
AD872A sample clock, because it is sampling a dc signal.
Figure 32. Offset Correction Using the AD568
UNDERSAMPLING USING THE AD872A AND AD9100
The AD872A’s on-chip THA optimizes transient response while
maintaining low noise performance. For super-Nyquist (undersampling) applications it may be necessary to use an external
THA with fast track-mode slew rate and hold mode settling
time. An excellent choice for this application is the AD9100, an
ultrahigh speed track-and-hold amplifier.
+VS
+5V
10mF
VI N
+VS –V S
CLOCK 2
IN
3.3mF
14
4
0.1mF
16
RT
20
AD9100
0.1mF
442
1
CLOCK 1
IN
RT
9
5
7
AD
96685
4
8
7
19
Q
2
18
127
Q
8*
AD
9617
3
2
4
3
510
–VS –VS
8
6
10
15
0.1mF
3.3mF
–5V
13
1
12
5
11
7
ALL CAPACITORS ARE 0.01mF
(LOW INDUCTANCE - DECOUPLING)
UNLESS OTHERWISE NOTED.
* OPTIONAL, SEE
AD9617 DATASHEET
10mF
–VS
T = 200ns
+5V
CLOCK 2
0V
t S = 17ns
tS
T = 200ns
+1V
CLOCK 1
–1V
Figure 33. Undersampling Using the AD872A and AD9100
REV. A
AD872A
EB
0.1mF
17
+VS = 5.0V
–VS = –5.2V
AIN
5*
10
510
6
–15–
AD872A
+5A
+5D
CLOCK INPUT
J2
R3
10
4
DVDD
AVDD
DGND
C12
0.1
JP3
7
6
C13
0.1
C14
0.1
DRVDD
AGND
ANALOG IN
J1
DGND
1
TP1
VINA
R1
C20
10pF
49.9
AD872A
CLK
OTR
2
VINB
MSB
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
BIT 8
BIT 9
BIT 10
BIT 11
BIT 12
27
REF GND
C7
10mF
C18
0.1
JP1
28
REF IN
JP2
REF OUT
U2
REF43
+5A
1
4
C22
0.1
C21
1mF
8
7
6
2
VIN
3
26
JP
* 11
R2
49.9
JP4
U3
74HC04
+5D
5
TP2
R5 20
23
R6 20
4
1
JP6
JP9
JP5
21
20
2
R7 20
5
6
R8 20
JP10
19
18
17
16
15
14
13
12
11
10
9
8
R9 20
R10 20
R11 20
R12 20
R13 20
R14 20
24
R15 20
AGND
VOUT
5
GND
AVSS
AVSS
3
* NOTE: JP11 SHOULD BE OPEN
1
JP7
3
C16
0.1
P1
40-PIN
IDC CONN.
JP8
22
C15
0.1
R4
R16 20
25
C11
0.1
C17
0.1
–5A
TP5
+5A
FB1
+5VA
TP4
C9
0.1
C5
22mF
C2
0.01
R17 20
AGND
C4
22mF
C1
0.01
–5VA
C8
0.1
FB2
+5D
FB3
+5VD
C3
0.01
C6
22mF
–5A
TP3
TP6
C10
0.1
TP7
40
DGND
Figure 34. AD872A/AD871 Evaluation Board Schematic
–16–
REV. A
AD872A
Figure 35. Silkscreen Layer PCB Layout (Not Shown to Scale)
Table IV. Components List
REV. A
Reference Designator
Description
Quantity
R1, R2
R3
R4–R17
Resistor, 1%, Metal Film, 49.9 Ω
Resistor, 1%, Metal Film, 10
Resistor, 1%, Metal Film, 20
2
1
14
C1–C3
C4–C6
C7
C8–C19, C22
C20
C21
SMD Chip Capacitor, 0.01 µF
Capacitor, Tantalum, 22 µF
Capacitor, Tantalum, 10 µF
SMD Chip Capacitor, 0.1 µF
Capacitor, Mica, 10 pF
Capacitor, Ceramic, 1 µF
3
3
1
13
1
1
U1
U2
U3
AD872A
REF43B
74HC04N
1
1
1
FB1–FB3
Ferrite Bead
3
J1, J2
BNC Jack
2
JP2, 3, 5, 7, 10
JP1–JP11
Jumpers
Headers
5
11
P1
40-Pin IDC Connector
1
–17–
AD872A
Figure 36. Component Side PCB Layout (Not Shown to Scale)
Figure 37. Solder Side PCB Layout (Not Shown to Scale)
–18–
REV. A
AD872A
Figure 38. Ground Layer PCB Layout (Not Shown to Scale)
Figure 39. Power Layer PCB Layout (Not Shown to Scale)
REV. A
–19–
AD872A
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
0.005 (0.13) MIN
C2001a–0–11/97
28-Lead Side Brazed DIP
(D-28)
0.100 (2.54) MAX
28
15
0.610 (15.49)
0.500 (12.70)
PIN 1
14
1
0.620 (15.75)
0.590 (14.99)
0.060 (1.52)
0.015 (0.38)
1.490 (37.85) MAX
0.225
(5.72)
MAX
0.200 (5.08)
0.150
(3.81)
MIN
0.125 (3.18)
0.026 (0.66)
0.014 (0.36)
0.110 (2.79)
0.090 (2.29)
0.070 (1.78)
0.030 (0.76)
0.018 (0.46)
0.008 (0.20)
SEATING
PLANE
44-Terminal LCC
(E-44A)
0.100 (2.54)
0.064 (1.63)
0.055 (1.40)
0.045 (1.14)
0.075 (1.91) REF
0.020 (0.51)
REF x 45 °
6
40
1
0.050
(1.27)
BSC
BOTTOM
VIEW
28
0.028 (0.71)
0.022 (0.56)
18
PRINTED IN U.S.A.
0.662 (16.82)
SQ
0.640 (16.27)
0.040 (1.02)
REF x 45 °
3 PLACES
–20–
REV. A
Similar pages