POWER DS2900 Data Sheet 2900 Watts Distributed Power System Distributed Power Bulk Front-End Total Output Power: 2900 Watts +3.3 Vdc Stand-by Output Wide Range Input Voltage: 180 - 264 Vac Special features Active power factor correction EN61000-3-2 harmonic compliance Active AC inrush control 2U X 3U form factor 24.8 W / in3 +12 Vdc Output +3.3 Vdc stand-by (5 V standby - consult factory) No minimum load required Hot plug operation N + 1 redundant Internal OR’ing fets Active current sharing (10 - 100% load) Built-in cooling fan (40 mm x 40 mm) I2C communication interface bus PMBus compliant EEPROM for FRU data 2 LED (Green and Amber) Internal fan speed control INTEL, SSI Std. logic timing INTEL, SSI Std. FRU data format PSMI V2.12 Full digital control Two year warranty Compatible with Universal PMBus GUI SAFETY UL/cUL 60950 (UL Recognized) NEMKO+ CB Report EN60950 EN60950 CE Mark China CCC Electrical Specifications Input Input range: 180 - 264 (2900 W) Frequency: 47-63 Hz, single phase AC Inrush current: 50 Apk maximum inrush current Efficiency: > 91% typical at nom line 50% load Conducted EMI: FCC Subpart J EN55022 Class A Radiated EMI: FCC Subpart J EN55022 Class A. Meets intent of NEBS, Bellcore GR-1089 Power factor: 0.99 typical Leakage current: 1.40 mA @ 240 VAC Hold up time: 10 mS minimum DS2900 Data Sheet Electrical Specifications Output Main DC voltage: +12 V @ 240 A (high line) Stand-By: +3.3 Vsb @ 3 A Adjustment range: ± 4% on +12V only using I2C Regulation: +12 Vdc; +4% / -4%; +3.3 Vsb; +5% / -5% Over current: Constant current type for both the 12 VDC and 3.3V standby. See Figure 1 below Over voltage: +12 Vdc; 14.4 - 15.6 Vdc (110 - 130%); +3.3 Vsb; 3.63 V - 4.29 (110 - 130%) Under voltage: +12 Vdc; 9 - 10 V nominal (latch off) Turn-on delay: 2 second max, 5 - 200 mS, monotonic rise Main output rise time: 5 - 300 mS, monotonic rise Iout limit Vout Vout nominal Iout (+12 Vdc) 110% (3.3 Vsb) 130% 120% 160% Figure1 Logic Control Remote ON/OFF (PSON#) The PSON# signal is required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the +12 Vdc power rail. When this signal is not pulled low by the system, or left open, the +12 Vdc output turns off. The 3.30 Vsb output remains on. This signal is pulled to a stanby voltage by a pull-up resistor internal to the power supply. The power supply fan(s) shall operate at the lowest speed Signal Type Accepts an open collector/drain input from the system. Pulled-up to the 3.30 Vsb located in the power supply PSON# = Low ON PSON = Open OFF MIN MAX Logic level low (power supply ON) 0V 0.8 V Logic level high (power supply OFF) 2.0 V 4.125 V # Source Current, Vpson = low Power up delay: Tpson on delay 4 mA 5 msec Table 1 PSON# Signal Characteristics 400 msec DS2900 Data Sheet Power Good (PWOK#) PWOK# is a power good signal and will be pulled LOW by the power supply to indicate that both the outputs are above the regulation limits of the power supply. When an output voltage falls below regulation limits or when AC power has been removed for a time sufficiently long so that power supply operation is no longer guaranteed, PWOK will be de-asserted to a HIGH state. The start of the PWOK# delay time shall be inhibited as long as the +12 Vdc output is in current limit or the 3.30 Vsb output is below the regulation limit. Signal Type: Open collector/drain output from power supply. Pull-up to 3.30Vsb external to the power supply PWOK = High Power not good PWOK = Low Power Good MIN MAX Logic level low voltage, Isink = 4 mA 0V 0.8 V Logic level high voltage, Isource = 200 A 2.0 V 4.125 V Sink current, PWOK = low 4 mA Source current, PWOK = high 2 mA PWOK delay: Tpwok on 100 ms PWOK rise and fall time Power down delay: Tpwok off 1000 ms 100 sec 1 ms 1000 msec Table 2 PWOK# Signal Characteristics Power Supply Present Indicator (PRESENT#) The PRESENT# signal is primarily used to provide a mechanism by which the host system can sense the number of power supplies physically present (operational or not). This pin is connected to ground in the power supply. AC Input Present Indicator (ACOK#) The AC OK# signal is used to indicate presence of AC input to the power supply. This signal shall be connected to 3.3 Vsb through a resistor on the host system side. A logic “Low” level on this signal shall indicate AC input to the power supply is present. A Logic “HIgh” on this signal shall indiciate a loss of AC input to the power supply. Signal Type Pull-up to 3.30 Vsb through a resitor in the host system PRESENT# = Low Present PRESENT = High Not Present # Table 3 ACOK# Signal Characteristics DS2900 Data Sheet Environmental Specifications Operating temperature: 0° to 50 °C (70 °C derated power) Storage temperature: -40 °C to +85 °C Altitude, operating: 10,000 ft Electromagnetic susceptibility / Input transients: -EN61000-3-2, -3-3 -EN61000-4-2, 4-3, 4-4, -4-5, 4-11 -EN55024:1998 RoHS & lead-free compliant: No tantalum caps. Humidity: 20 to 90% RH, non-condensing Shock and vibration specificatons: Complies with Astec Std. Specifications, QP3205 MTBF (Calculated): 300K Hrs Bellcore TR-332, Issue 6 @ 25 °C and 40 °C full load MTBF (Demonstrated): > 500k Hrs Ordering Information Model Number Total Minimum Maximum Output Nominal Output Set Point Voltage Set Point Tolerance Regulation Current Current Ripple P/P Over Current Stand-by Air Flow DS2900-3 12.0 Vdc ± 0.2% ± 4% 0A 240 A 120 mV 276 A nominal 3.3 V @ 3 A Standard DS2900-3-002 12.0 Vdc ± 0.2% ± 4% 0A 240 A 120 mV 276 A nominal 5.0 V @ 2 A Standard DS2900-3-003 12.0 Vdc ± 0.2% ± 4% 0A 240 A 120 mV 276 A nominal 5.0 V @ 2 A Reversed DS2900-3-004 12.0 Vdc ± 0.2% ± 4% 0A 240 A 120 mV 276 A nominal 3.3 V @ 3 A Reversed *Overcurrent latches off if overcurrent lasts over 2 seconds DS2900 Data Sheet AIRFLOW DIRECTION 208 HANDLE 138.4 EMI CLIP 17.5 217 ± 0.75 138.4 13.2 1.9 2 (2X) 14.5 96.6 77 106 ± 0.75 4.7 4 ± 0.5 1.9 (TYP) EMI CLIP 26.4 ± 0.5 78 ± 0.75 EMI CLIP 19.17 ± 0.5 Mechanical Drawing 52 16.8 EMI CLIP LED FAN 60X60X38 Condition LED Status Stand-by - ON; Main output - OFF; AC PRESENT Blinking green Stand-by - ON; Main output - ON; Solid green Main output OCP, UVP, OVP Blinking Amber FAN_FAULT; OTP; Stand-by OCP/UVP Amber FAN GRILLE DS2900 Data Sheet Output Connector Pin Configuration DC Output Connector FCI HCI Series Plug (10 Blades, 24 Signal pins). Power Supply; FCI P/N; SK10065864-003LF FCI HCI Series Receptacle (10 Blades, 24 Signal pins). Mating; FCI P/N; SK10065866-003LF P1 - System Pin Signal Name Amps per pin1 Internal to power supply PB1 + Vout 100 PB2 + Vout 100 PB3 + Vout 100 PB4 + Vout 100 PB5 + Vout 100 PB6 + Vout Return 100 PB7 + Vout Return 100 PB8 + Vout Return 100 FCI HCI Series Connector 10 Power Blades 24 Signal pins P/N SK10085236-003LF FCI HCI Series Connector Molex Power Dock Senior 10 Power Blades 24 Signal pins P/N SK10065866-003LF *Supports I2C standard mode (100 kHz) only PB9 + Vout Return 100 PB10 + Vout Return 100 A1 PS_KILL 1.5 A2 +PS_ON 1.5 A3 +VoutI_Share N/A A4 S_INT N/A A5 +STBY N/A A6 +STBY Return N/A B1 PS_SEATED 1.5 B2 ACOK 1.5 B3 PWR_GOOD N/A B4 A2 N/A B5 +STBY N/A B6 +STBY Return N/A C1 SDA 1.5 C2 SCL* 1.5 C3 A1 N/A C4 A0 N/A C5 +STBY N/A C6 +STBY Return N/A D1 Reserve 1.5 D2 WP 1.5 D3 +Vout_RS N/A D4 +Vout_RS_RETURN N/A D5 +STBY N/A D6 +STBY Return N/A DS2900 Data Sheet Connector Definition Power Supply Input Connector FCI P/N 51939-081LF Tyco P/N 6600100-2 System Mating Connector FCI P/N 51915-022LF or 51940-059 WORLDWIDE OFFICES Americas Europe (UK) Asia (HK) 2900 S.Diablo Way Tempe, AZ 85282 USA +1 888 412 7832 Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom +44 (0) 1384 842 211 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong +852 2176 3333 While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners. © 2014 Artesyn Embedded Technologies, Inc. www.artesyn.com For more information: www.artesyn.com/power For support: [email protected] DS2900 Rev. 10.15.14