VDE VDE Pending (AQH1213, AQH1223, AQH2213, AQH2223) (AQH0213, AQH0223, AQH3213, AQH3223) AQ-H RELAYS AQ-H SOLID STATE RELAY FEATURES – 1 + 2 – 3 – 4 – 8 1 + 2 – 6 3 – 5 4 ZC Zero-cross circuit 1. Compact DIP type SSR that’s ideal for AC load control 2. Supports 0.3 A, 0.6 A, 0.9 A and 1.2 A ON-state RMS currents. 3. The 1.2 A type saves space with a DIP 8-pin package. (Competitor only provides a 16-pin type.) 8 9.78 .385 6 6.4 .252 5 DIP8 DIP16 19.82 .780 (mm inch) 4. Only ours handles both 100 and 200 V AC loads This relay handles both voltages in a single product. It is not necessary for users that use both types to manage separate part numbers. 5. High dielectric strength: 5,000 V AC (between input and output) 6. Two types available: Zero-cross type and Non-zero-cross type TYPICAL APPLICATIONS 1. Home appliances (air conditioners, microwave ovens, washing machines, personal hygiene systems, refrigerators, fan heaters, inductive heating cooker, and water heaters, etc.) 2. Industrial equipment market. TYPES Part No. Output rating* Type Through hole terminal Type Repetitive ON-state peak OFFRMS current state voltage AC type 600 V 0.3 A 0.6 A 0.9 A 1.2 A 0.3 A 0.6 A 0.9 A 1.2 A Tube packing style Zero-cross Non zero-cross AQH0213 AQH1213 AQH2213 AQH3213 AQH0223 AQH1223 AQH2223 AQH3223 Packing quantity Surface-mount terminal AQH0213A AQH1213A AQH2213A AQH3213A AQH0223A AQH1223A AQH2223A AQH3223A Tape and reel packing style Tape and Tube Picked from the Picked from the reel 1/2/3/4-pin side 5/6/8-pin side AQH0213AX AQH0213AZ AQH1213AX AQH1213AZ AQH2213AX AQH2213AZ 1 tube contains AQH3213AX AQH3213AZ 40 pcs. 1,000 pcs. AQH0223AX AQH0223AZ 1 batch contains 400 pcs. AQH1223AX AQH1223AZ AQH2223AX AQH2223AZ AQH3223AX AQH3223AZ *Indicate the repetitive peak OFF-state voltage and ON-state RMS current: peak AC. Note: For space reasons, the SMD terminal shape indicator “A” and the package type indicator “X” and “Z” are omitted from the seal. RATING 1. Absolute maximum ratings (Ambient temperature: 25°C 77°F) Input Item LED forward current LED reverse voltage Peak forward current Repetitive peak OFF-state votage Output ON-state RMS current Non-repetitive surge current I/O isolation voltage Temperature limits Symbol AQH0213 AQH0223 AQH1213 AQH1223 AQH2213 AQH2223 AQH3213 AQH3223 IF 50 mA VR 6V IFP f = 100 Hz, Duty Ratio = 0.1% 1A VDRM IT(RMS) ITSM Viso Remarks 600 V 0.3 A 3A 0.6 A 6A 0.9 A 9A 1.2 A 12 A 60Hz, 1 cycle 5,000 V AC Operating Topr –30°C to +85°C –22°F to +185°F Storage Tstg –40°C to +125°C –40°F to +257°F AQ-H SOLID STATE RELAY ASCT1B272E ’03.7 http://www.naisrelay.com/ Non-condensing at low temperatures New 1 AQ-H 2. Electrical characteristics (Ambient temperature: 25°C 77°F) Item Symbol AQH0213 AQH1213 AQH2213 AQH3213 AQH0223 AQH1223 AQH2223 AQH3223 LED dropout voltage Input LED reverse current Peak OFF-state current Output Peak ON-state voltage Holding current Critical rate of rise of OFF-state voltage Transfer characteristics Typical Maximum Typical Maximum Typical Maximum Typical Maximum Typical Maximum 1.18 V 1.3 V — 10 µA — VF IR IDRM IF = 10 mA VR = 6 V IF = 0 mA VDRM = 600 V 100 µA — VTM IF = 10 mA ITM = Max. 2.5 V — 25 mA IH dv/dt 200 V/µs Trigger LED current* Maximum IFT 10 mA Zero-cross voltage** Maximum VZC Turn on time*** Maximum TON 10 µs I/O isolation resistance Minimum Riso 50 GΩ Minimum Condition VDRM = 600 V ×1/M2 50 V VD = 6 V RL = 100 Ω IF = 10 mA IF = 20 mA VD = 6 V RL = 100 Ω — 500 V DC Notes: *Recommended LED current IFT: 20 mA **Applicable part No.: AQH0213, AQH1213, AQH2213 and AQH3213. ***Turn on time Input 90% Output Ton DIMENSIONS mm inch Through hole terminal type Surface mount terminal type MAX.10° PC board pattern (BOTTOM VIEW) 7.62 .300 8-0.8 dia. hole 8-.031 dia. hole MAX. 10° 6.4 .252 6.4 .252 7.62 .300 7.62 .300 2.54 .100 6.4 .252 7.62 2.54 .300 .100 MAX. 10° 1 3.4 .134 9.78 .385 9.78 .385 3.4 .134 3.9±0.2 .154±.008 0.2 .008 3.0 .118 0.5 .020 1.2 .047 3.4 .134 0.5 0.5 .020 .020 1.2 1.2 .047 .047 0.5 .020 1.2 .047 +0.2 –0 +.008 –0 0.5 0.5 .020 0.5 .020 .020 1.2 1.2 .047 1.2 .047 .047 0.5 .020 1.2 .047 2.54 2.54 2.54 .100 .100 .100 2 Recommended mounting pad (TOP VIEW) 8.3 .327 1.9 .075 1.5 .059 2.54 2.54 2.54 .100 .100 .100 Terminal thickness: 0.25 .010 General tolerance: ±0.1 ±.004 Tolerance: ±0.1 ±.004 Terminal thickness: 0.25 .010 General tolerance: ±0.1 ±.004 2.54 2.54 2.54 .100 .100 .100 Tolerance: ±0.1 ±.004 AQ-H SCHEMATIC AND WIRING DIAGRAMS Notes: E1: Power source at input side; IF: Trigger LED forward current; VL: Load voltage; IL: Load current; Schematic – 1 + 2 – 3 – 4 Output configuration Load Wiring diagram 2 E1 Load 8 1 8 IL IF 3 6 4 5 1 8 IL VL (AC) 6 ZC Zero-cross circuit VL (AC) Load 5 1a – 1 + 2 – 3 – 4 AC 8 2 E1 6 Load IL IF 3 6 4 5 IL VL (AC) VL (AC) Load 5 REFERENCE DATA 1. ON-state RMS current vs. Ambient temperature characteristics 2. On voltage vs. Ambient temperature characteristics 3. Trigger LED current vs. Ambient temperature characteristics Allowable ambient temperature: –30°C to +85°C –22°F to +185°F LED current: 10 mA; ON current: Max. Measured portion: between terminals 6 and 8 Load voltage: 6 V DC; Load resistance: 100Ω 0.6 0.3 1.4 AQH2213, AQH2223 AQH1213, AQH1223 0 20 AQH1213, AQH1223 1.2 AQH2213, AQH2223 1 0.8 40 60 0.6 –40 –30 –20 80 85 100 20 40 60 100 1.4 80 1.3 50mA 1.2 30mA 10mA 60 60 40 20 0 80 85 0 10 20 Ambient temperature, °C 30 40 50 40 60 80 85 6. Repetitive peak OFF-state current vs. Load voltage characteristics 10–3 10–4 10–5 10–6 10–7 10–8 10–9 10–10 0 20 40 60 80 100 Load voltage, V LED current, mA 7. Hold current vs. Ambient temperature characteristics 20 LED current: 0 mA; Measured portion: between terminals 6 and 8; Ambient temperature: 25°C 77°F 20mA 1.1 0 Ambient temperature, °C Repetitive peak OFF-state current, A 1.5 40 0 –40 –30 –20 80 85 Load voltage: 6 V DC; Load resistance: 100Ω Measured portion: between terminals 6 and 8 Turn on time, µs LED dropout voltage, V 0 5. Turn on time vs. LED current characteristics LED current: 10 to 50 mA 20 4 Ambient temperature, °C 4. LED dropout voltage vs. Ambient temperature characteristics 0 6 2 Ambient temperature, °C 1 –40 –30 –20 8 AQH3213, AQH3223 AQH0213, AQH0223 0 –30 –20 AQH0213, AQH0223 Trigger LED current, mA 0.9 AQH3213, AQH3223 On voltage, V ON-state RMS current, mA 1.2 10 1.6 1.5 8. Zero-cross voltage vs. Ambient temperature characteristics LED current: 10 mA 50 20 15 AQH1213, AQH1223 AQH2213, AQH2223 10 5 Zero-cross voltage, V Hold current, mA 25 40 AQH0213, AQH1213, AQH2213, AQH3213 30 20 10 AQH0213, AQH0223 AQH3213, AQH3223 0 –40 –30 –20 0 20 40 60 Ambient temperature, °C 80 85 0 –40 –30 –20 0 20 40 60 80 85 Ambient temperature, °C 3 AQ-H CAUTIONS FOR USE 1. For cautions regarding use, please refer to ’03-’04 Solid State Relays catalog. 2. The internal IC could be damaged if a short forms between the I/O terminals while the solid state relay is powered. 3. Output spike voltages 1) The figure below shows an ordinary circuit. Please add a snubber circuit or varistor, as noise/surge on the load side could damage the unit or cause malfunctions. 1 8 Load 2 VL(AC) 3 6 4 5 Note) Connection of an external resister, etc., to terminal No. 5 (gate) is not necessary. 2) Even if spike voltages generated at the load are limited with a clamp diode if the circuit wires are long, spike voltages will occur by inductance. Keep wires as short as possible to minimize inductance. 4. Ripple in the input power supply 1) For LED operate current at Emin, maintain min. 10 mA 2) Keep the LED operate current at 50 mA or less at Emax. 6. Cleaning The solid state relay forms an optical path by coupling a light-emitting diode (LED) and photodiode via transparent silicon resin. For this reason, avoid ultrasonic cleansing if at all possible. We recommend cleaning with an organic solvent. If you cannot avoid using ultrasonic cleansing, please ensure that the following conditions are met, and check beforehand for defects. • Frequency: 27 to 29 kHz • Ultrasonic output: No greater than 0.25 W/cm2 • Cleaning time: No longer than 30 seconds • Cleanser used: Asahiklin AK-225 • Other: Submerge in solvent in order to prevent the PCB and elements from being contacted directly by the ultrasonic vibrations. (2) Vapor phase soldering method Note: Applies to unit area ultrasonic output for ultrasonic baths. (4) Soldering iron method Tip temperature: 280 to 300°C 536 to 572°F Wattage: 30 to 60 W Soldering time: within 5 seconds (5) Others Check mounting conditions before using other soldering methods (hot-air, hot plate, pulse heater, etc.) • The temperature profile indicates the temperature of the soldered terminal on the surface of the PC board. The ambient temperature may increase excessively. Check the temperature under mounting conditions. • The conditions for the infrared reflow soldering apply when preheating using the VPS method. 7. Soldering 1) When soldering PC board terminals, keep soldering time to within 10 s at 260°C 500°F. 2) When soldering surface-mount terminals, the following conditions are recommended. (1) IR (Infrared reflow) soldering method T3 Emin. T2 Emax. T1 5. When soldering terminals, keep soldering time to within 10s at 260°C 500°F t1 t2 T1 = 155 to 165°C 311 to 329°F T2 = 180°C 200°C 356 to 392°F T3 = 245°C 473°F or less t1 = 120 s or less t2 = 30 s or less T2 T1 t1 t2 T1 = 180 to 200°C 366 to 392°F T2 = 215°C 419°F or less t1 = 40 s t2 = 90 s or less (40 s: SOP type) (3) Double wave soldering method T2 T1 t1 t2 t3 T1 = 155 to 165°C 311 to 329°F T2 = 260°C 500°F or less t1 = 60 s or less t2+t3 = 5 s or less 8. The following shows the packaging format 1) Tape and reel Type mm inch Tape dimensions 0.3±0.05 .012±.002 8-pin SMD type Tractor feed holes –0 1.5 +0.1 dia. .059 +.004 dia. –0 21±0.8 .827±.031 80±1 dia. 3.150±.039 dia. Direction of picking 4±0.1 10.1±0.1 .157±.004 .400±.004 1.75±0.1 .069±.004 2±0.5 .079±.020 7.5±0.1 .295±.004 16±0.3 .630±.012 Device mounted on tape 4.5±0.3 .177±.012 Dimensions of paper tape reel 12±0.1 .472±.004 2±0.1 .079±.004 300±2 dia. 11.811±.079 dia. 80±1 dia. 3.150±.039 dia. 10.2±0.1 .402±.004 1.55±0.1 dia. .061±.004 dia. (1) When picked from 1/2/3/4-pin side: Part No. AQH❍❍❍❍AX (Shown above) (2) When picked from 5/6/8-pin side: Part No. AQH❍❍❍❍AZ 13±0.5 dia. .512±.020 dia. 17.5±2.0 .689±.079 4 2±0.5 .079±.020 AQ-H 2) Tube Devices are packaged in a tube so pin No. 1 is on the stopper B side. Observe correct orientation when mounting them on PC boards. (DIP type) StopperB StopperA 9. Transportation and storage 1) Extreme vibration during transport will warp the lead or damage the relay. Handle the outer and inner boxes with care. 2) Storage under extreme conditions will cause soldering degradation, external appearance defects, and deterioration of the characteristics. The following storage conditions are recommended: • Temperature: 0 to 45°C 32 to 113°F • Humidity: Less than 70% R.H. • Atomosphere: No harmful gasses such as sulfurous acid gas, minimal dust. 5 AQ-H Internet Homepage North America : http://www.aromat.com/ Europe : http://www.mew-europe.com/ Asia & others : http://www.nais-e.com/ • (Japanese) : http://www.mac-j.co.jp/ • (Chinese) : http://www.cmew.com.cn/ These materials are printed on ECF pulp. These materials are printed with earth-friendly vegetable-based (soybean oil) ink. Please contact .......... Matsushita Electric Works, Ltd. Automation Controls Company Head Office: 1048, Kadoma, Kadoma-shi, Osaka 571-8686, Japan Telephone: Japan (81) Osaka (06) 6908-1050 Facsimile: Japan (81) Osaka (06) 6908-5781 http://www.nais-e.com/ COPYRIGHT © 2003 All Rights Reserved ARCT1B272E 200307-3YT 6 Specifications are subject to change without notice. Printed in Japan.