HPF24S6 and HPF24S8 Description Power Supplies with Battery Chargers The HPF24S6 and HPF24S8 are compact, cost-effective, 6 amp. or 8 amp. remote power supplies with integral battery chargers. These adaptable power supplies may be connected to any 12 or 24 volt Fire Alarm Control Panel (FACP) or the power supplies may stand alone. Primary applications include the following: • Notification Appliance Circuits (NAC) expansion to support ADA requirements and NAC synchronization • Auxiliary power to support 24 volt system accessories HFP24S6/8 dh1061.jpg These power supplies provide regulated and filtered 24 VDC power to four (4), notification appliance circuits, configured as either four Class B (Style Y) or Class A (Style A, with ZNAC-4 Option Module). Alternately, the four outputs may be configured as follows: • all non-resettable Features • all resettable • Cascade up to ten (10) power supplies (four (4) power • UL Listed NAC synchronization using System Sensor, Cooper-Wheelock or Gentex (Commander Series) appliances. • two non-resettable supplies with Gentex) with strobe timing maintained. • two resettable • Operates as a sync follower or a sync generator The power supplies also contain a battery charger with a charging capacity of up to 18 Amp Hour batteries. • Contains two (2), fully -isolated input/control circuits (default). energized from FACP notification appliance circuit The HPF24S6 and HPF24S8 power supplies comply with the following Agency standards: • NFPA 72 National Fire Alarm Code, • UL Standard 864, 9th Edition for control units for Fire Alarm Systems (NAC expander mode). • UL 1481 Power Supplies for Fire Alarm Systems (stand-alone mode). (NAC expander mode) or jumpered permanently on (stand-alone mode). • Configured to internally house addressable SLC control module for alarm activation. • Four (4) Class B (Style Y) or four (4), Class A (Style Z) (with ZNAC-4 Module) notification appliance circuits. • 6.0A or 8.0A (depending on model) full load output (3.0A maximum per circuit) in NAC expander mode (UL Standard 864). • 4.0A or 6.0A continuous output in stand-alone mode (UL Standard 1481). An ISO 9000-2000 Company SIGNALING UOXX.S6677 7315-1637:102 UTRZ.S6677 GAMEWELL-FCI 12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118 Specifications are for information only, are not intended for installation purposes, and are subject to change without notice. No responsibility is assumed by Gamewell-FCI for their use. ©2007 Honeywell International Inc. All rights reserved. www.gamewell-fci.com CS-60062 Rev. A1 page 1 of 2 Features (Continued) Specifications (Continued) • In stand-alone mode, output power circuits configured as resettable, (using the FACP reset switch), non-resettable, or a combination of both. • Fully regulated and filtered power output (optimal for powering four-wire smoke detectors, annunciators and other system peripherals requiring regulated/filtered power). • Power-limiting technology meets UL power-limiting requirements. • Normally-closed trouble relay. • Fully supervised power supply, battery and notification Output Circuits • +24 VDC filtered, regulated • 3.0A maximum for any one circuit • 4.0A maximum total continuous current for all outputs (Stand-alone mode) for the HPF24S6 and 6A for the HPF24S8 • 6A or 8A, depending on the model, maximum total short-term current for all outputs (NAC Expander mode). Secondary Power (Battery) Charging Circuit • Supports lead-acid batteries only • Float Charge Voltage: 27.6 VDC • Maximum Charge Current: 1.5A • Maximum Battery Capacity: 18 AH appliance circuits. Ordering Information • Selectable earth fault detection. • AC trouble report selectable for immediate or up to 8 Model HPF24S6 hour delay. • Compatible with any UL 864 fire alarm control which uses an industry standard reverse polarity notification circuit (including unfiltered and unregulated bell power). HPF24S8 • Requires input trigger voltage of 9.0 -32 VDC. • Self-contained in compact, lockable cabinet 15” H x 14.5” W x 2.75” D (38.1 H x 36.8 W x 7.0 D cm). • Includes an integral battery charger capable of charging up to 18 AH batteries. The cabinet has the capacity of housing 7.0 AH batteries. FCPS-24S6RB ZNAC-4 BAT-1270 - Description Remote charger 6A power supply (120 VAC). Includes the main printed circuit board, transformers, red enclosure, and installation instructions. Remote charger 8A power supply (120 VAC). Includes the main printed circuit board, transformers, red enclosure, and installation instructions. Replacement mother board. Class A (Style Z) NAC option module Battery, 12 volt, 7.0 AH (two required). • Battery charger may be disabled via DIP (Dual In-Line Package) switch for applications requiring larger batteries. • Fixed, clamp-type terminal blocks accommodate up to 12 AWG (3.1 mm2) wire. Specifications Primary (AC) Power • HPF24S6: 120 VAC 60 Hz, 3.2A maximum • HPF24S8: 120 VAC 60 Hz, 3.2A maximum • Wire size: minimum 14 AWG (2.0 mm²) with 600V insulation Control Input Circuit • Input Voltage: 9.0 to 32 VDC • Input Current: 2.0 mA (16 - 32 V) per input 1.0 mA (9 - 16 V) Trouble Contact Rating • 5.0A at 24 VDC Auxiliary Power Output • Specific Application Power - 500 mA maximum GAMEWELL-FCI 12 Clintonville Road, Northford, CT 06472-1610 USA • Tel: (203) 484-7161 • Fax: (203) 484-7118 www.gamewell-fci.com CS-60062 Rev. A1 page 2 of 2