M54HC125 RAD-HARD QUAD BUS BUFFER (3-STATE) ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ HIGH SPEED: tPD = 8ns (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC = 4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = VNIL = 28% VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 6mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 54 SERIES 125 SPACE GRADE-1: ESA SCC QUALIFIED 50 krad QUALIFIED, 100 krad AVAILABLE ON REQUEST NO SEL UNDER HIGH LET HEAVY IONS IRRADIATION DEVICE FULLY COMPLIANT WITH SCC-9401-039 DILC-14 FPC-14 ORDER CODES PACKAGE FM EM DILC FPC M54HC125D M54HC125K M54HC125D1 M54HC125K1 The device requires the 3-STATE control input G to be set high to place the output into the high impedance state. All inputs are equipped with protection circuits against static discharge and transient excess voltage. DESCRIPTION The M54HC125 is an high speed CMOS QUAD BUFFER (3-STATE) fabricated with silicon gate C2MOS technology. PIN CONNECTION March 2004 1/9 M54HC125 IEC LOGIC SYMBOLS INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN N° SYMBOL 1, 4, 10, 13 2, 5, 9, 12 3, 6, 8, 11 7 1G TO 4G 1A TO 4A 1Y TO 4Y GND VCC 14 NAME AND FUNCTION Output Enable Input Data Inputs Data Outputs Ground (0V) Positive Supply Voltage TRUTH TABLE A G Y X L H H L L Z L H ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Supply Voltage Value Unit -0.5 to +7 V VI DC Input Voltage -0.5 to VCC + 0.5 V VO DC Output Voltage -0.5 to VCC + 0.5 ± 20 V mA IIK DC Input Diode Current IOK DC Output Diode Current ± 20 mA IO DC Output Current ± 35 mA ± 70 mA ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg Storage Temperature TL Lead Temperature (10 sec) 420 mW -65 to +150 °C 265 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 2/9 M54HC125 RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Output Voltage Top Operating Temperature Input Rise and Fall Time tr, tf Value Unit 2 to 6 V 0 to VCC V 0 to VCC V -55 to 125 °C VCC = 2.0V 0 to 1000 ns VCC = 4.5V 0 to 500 ns VCC = 6.0V 0 to 400 ns DC SPECIFICATIONS Test Condition Symbol VIH VIL VOH VOL II IOZ ICC Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage Input Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Value TA = 25°C VCC (V) Min. 2.0 4.5 6.0 2.0 4.5 6.0 Typ. Max. 1.5 3.15 4.2 -40 to 85°C -55 to 125°C Min. Min. Max. 1.5 3.15 4.2 0.5 1.35 1.8 Max. 1.5 3.15 4.2 0.5 1.35 1.8 Unit V 0.5 1.35 1.8 2.0 IO=-20 µA 1.9 2.0 1.9 1.9 4.5 IO=-20 µA 4.4 4.5 4.4 4.4 6.0 IO=-20 µA 5.9 6.0 5.9 5.9 4.5 IO=-6.0 mA 4.18 4.31 4.13 4.10 6.0 IO=-7.8 mA 5.68 5.8 5.63 5.60 2.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=20 µA 0.0 0.1 0.1 0.1 V V 6.0 IO=20 µA 0.0 0.1 0.1 0.1 4.5 IO=6.0 mA 0.17 0.26 0.33 0.40 6.0 IO=7.8 mA 0.18 0.26 0.33 0.40 6.0 VI = VCC or GND ± 0.1 ±1 ±1 µA 6.0 VI = VIH or VIL VO = VCC or GND ± 0.5 ±5 ± 10 µA 6.0 VI = VCC or GND 4 40 80 µA V 3/9 M54HC125 AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 6ns) Test Condition Symbol Parameter tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time tPZL tPZH High Impedance Output Enable Time tPLZ tPHZ High Impedance Output Disable Time VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 Value TA = 25°C CL (pF) Min. 50 50 150 50 RL = 1 KΩ 150 RL = 1 KΩ 50 RL = 1 KΩ Typ. Max. 20 6 5 36 9 8 52 13 11 36 9 8 52 13 11 48 12 10 60 12 10 75 15 13 105 21 18 75 15 13 105 21 18 80 16 14 -40 to 85°C -55 to 125°C Min. Min. Max. 75 15 13 95 19 16 130 26 22 95 19 16 130 26 22 100 20 17 Unit Max. 90 18 15 110 22 19 160 32 27 110 22 19 160 32 27 120 24 20 ns ns ns ns ns ns CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter VCC (V) Value TA = 25°C Min. Typ. Max. 10 CIN Input Capacitance 5.0 5 CPD Power Dissipation Capacitance (note 1) 5.0 35 -40 to 85°C -55 to 125°C Min. Min. Max. 10 Unit Max. 10 pF pF 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/4 (per buffer) 4/9 M54HC125 TEST CIRCUIT TEST tPLH, tPHL SWITCH Open tPZL, tPLZ VCC tPZH, tPHZ GND CL = 50pF/150pF or equivalent (includes jig and probe capacitance) R1 = 1KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω)) WAVEFORM 1: PROPAGATION DELAY TIMES (f=1MHz; 50% duty cycle) 5/9 M54HC125 WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIMES (f=1MHz; 50% duty cycle) 6/9 M54HC125 DILC-14 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 2.1 22.54 0.083 0.100 a1 3.00 3.70 0.118 0.146 a2 0.63 0.88 1.14 0.025 0.035 0.045 B 1.82 2.03 2.39 0.072 0.080 0.094 b 0.40 0.45 0.50 0.016 0.018 0.020 b1 0.20 0.254 0.30 0.008 0.010 0.012 D 18.79 19.00 19.20 0.740 0.748 0.756 e 7.36 7.62 7.87 0.290 0.300 0.310 e1 2.54 0.100 e2 15.11 15.24 15.37 0.595 0.600 0.605 e3 7.62 7.87 8.12 0.300 0.310 0.320 F 7.11 7.75 0.280 I 0.305 3.70 K 10.90 L 1.14 1.27 0.146 12.1 0.429 1.5 0.045 0.476 0.050 0.059 0016173H 7/9 M54HC125 FPC-14 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 6.75 6.91 7.06 0.266 0.272 0.278 B 9.76 9.95 10.14 0.384 0.392 0.399 C 1.49 1.95 0.059 D 0.10 0.127 0.15 0.004 0.005 0.006 E 7.50 7.62 7.75 0.295 0.300 0.305 F G 1.27 0.38 0.050 0.43 H L 0.077 0.48 0.015 0.017 6.0 0.019 0.236 18.75 22.0 0.738 0.866 M 0.38 0.015 N 4.31 0.170 G F D H 14 8 L N A 7 1 H E B 8/9 M C 016029E M54HC125 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2004 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 9/9