AIMTEC AM30K-2415DZ 30 watt | dc-dc converter Datasheet

Series AM30K-Z
30 Watt | DC-DC Converter
FEATURES:
•
•
•
•
Models: Single output
Model
Input –
Voltage (V)
AM30K-1203SZ
AM30K-1205SZ
AM30K-1212SZ
AM30K-1215SZ
AM30K-2403SZ
AM30K-2405SZ
AM30K-2412SZ
AM30K-2415SZ
AM30K-4803SZ
AM30K-4805SZ
AM30K-4812SZ
AM30K-4815SZ
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
36-75
36-75
36-75
36-75
Models: Dual output
Model
Input –
Voltage (V)
AM30K-1212DZ
AM30K-1215DZ
AM30K-2412DZ
AM30K-2415DZ
AM30K-4812DZ
AM30K-4815DZ
9-18
9-18
18-36
18-36
36-75
36-75
Wide Input 2:1 Range
Full SMD Technology
1500 VDC Isolation
Efficiency up to 91%
•
•
•
•
Adjustable Output Voltage
Remote ON/OFF Function
Over Current, Voltage, & Temperature Protection
Soft Start
Output
Voltage
(V)
Output Current
max (A)
Isolation
(VDC)
3.3
5
12
15
3.3
5
12
15
3.3
5
12
15
5.5
5.0
2.5
2.0
5.5
5.0
2.5
2.0
5.5
5.0
2.5
2.0
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
1500
Output
Voltage
(V)
Output Current
max (A)
Isolation
(VDC)
±1.25
±1.0
±1.25
±1.0
±1.25
±1.0
1500
1500
1500
1500
1500
1500
±12
±15
±12
±15
±12
±15
Max
Capacitive
Load (uF)
Efficiency
(%)
15000
10000
2200
1000
15000
10000
2200
1000
15000
10000
2200
1000
83
86
90
90
84
87
91
91
84
87
91
91
Max
Capacitive
Load (uF)
Efficiency
(%)
±1000
±680
±1000
±680
±1000
±680
90
90
91
91
90
90
NOTE: All specifications in this datasheet are measured at an ambient temperature of 25°C, humidity<75%, nominal input voltage and at
rated output load unless otherwise specified.
Input Specifications
Input Specifications
Voltage range
Filter
Start up time
Absolute Maximum Rated Input
Voltage
Peak Input Voltage time
On/Off Control
Isolation Specifications
Parameters
Tested I/O voltage
Resistance
Capacitance
www.aimtec.com
F 051e R8.F
Nominal
12
24
48
Typical
9-18
18-36
36-75
20
Maximum
Units
VDC
π(Pi) Network
ms
25
50
VDC
100
100
ms
ON – high or open (2.5V TO 5.5V); OFF – low (-0.7V to 0.8V or short circuit between pin 2 & 3)
12
24
48
Conditions
3 sec
Typical
1000
1200
Tel: +1 514 620 2722
1 of 4
Rated
1500
Units
VDC
MOhm
pF
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM30K-Z
30 Watt | DC-DC Converter
Output Specifications
Output Specifications
Voltage accuracy
Voltage balance (Dual Output model)
Over voltage protection
Over current protection
Short Circuit protection
Short circuit restart
Line voltage regulation (Single)
Line voltage regulation (Dual)
Load voltage regulation (Single)
Load voltage regulation (Dual)
Temperature coefficient
Ripple & Noise
Voltage adjustment range
General Specifications
Input Specifications
Switching frequency
Operating temperature
Storage temperature
Max Case temperature
Cooling
Humidity
Over Temperature Protection
Case material
Weight
Dimensions (L X W X H)
MTBF
Conditions
Typical
±5
±5
125
120
Balanced Load
HL-LL
HL-LL
10% to 100% Load
10% to 100% Load
At 20MHz Bandwidth
Maximum
Continuous
Auto Recovery
±5
±5
±0.5
±0.5
±0.02
75
±10
Conditions
100% load
With drating above 60 oC (see graph below)
Typical
270
Units
%
%
%
%
%
%
%
%
%/oC
m Vp-p
%
Maximum
Units
-40 to +85
-40 to +125
100
Free air convection
95
110
Nickel-coated Copper and Epoxy (UL94V-0 rated)
48
2.00 x1.60 x0.40 inches
50.80 x 40.60 x 10.20 mm
>1000000 hrs Calculated using MIL-HDBK-217 F at +25 oC
KHz
o
C
o
C
%
g
Safety Specifications
Standards
Agency approvals
Safety
www.aimtec.com
F 051e R8.F
CE
IEC/EN 60950-1
EN55022 Class A
EN55022 Class A
EN61000-4-2 Perf. Criteria B
EN61000-4-3 Perf. Criteria A
EN61000-4-4 Perf. Criteria B
EN61000-4-5 Perf. Criteria B
EN61000-4-6 Perf. Criteria A
EN61000-4-8 Perf. Criteria A
Tel: +1 514 620 2722
2 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM30K-Z
30 Watt | DC-DC Converter
Pin Out Specifications
+Vin
-Vin
On/Off Control
No Pin
+Vout
-Vout
Trim
+Vin
-Vin
On/Off Control
+Vout
Com
-Vout
Trim
50.80
(2.00)
4
40.60
(1.60)
7.62 10.16 5.08
(0.30) (0.40) (0.20)
17.78
(0.70)
Dimensions
Dual
Bottom View
3
6
7
Dimensions mm (inch)
Case Tolerance ±0.50 (±0.02)
Pin Pitch Tolerance ±0.35 (±0.014)
Ø 1.00
(0.04)
5.08
(0.20)
2.54
(0.10)
2
5
45.72
(1.80)
Built-in Stand-offs to
ease PCB Cleaning
10.16
(0.40)
Printed
Face
1
10.16 10.16 10.16
(0.40) (0.40) (0.40)
Single
5.10
(0.20)
1
2
3
4
5
6
7
5.10
(0.20)
Pin
Trimming
www.aimtec.com
F 051e R8.F
Tel: +1 514 620 2722
3 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Series AM30K-Z
30 Watt | DC-DC Converter
Derating
Free Air Convection
60º C
Output Power (%)
100
80
60
Safe Operating Area
40
20
0
- 40
- 20
0
20
40
60
80
85
100
Ambient Temperature º C
Control ON/OFF pin connection example:
Note A: An external filter capacitor is required if the module has to meet EN61000-4-4 and EN61000-4-5.
The filter capacitor Aimtec suggests: 1000uF, 100V.
Models
AM30K-12XXXZ
AM30K-24XXXZ
AM30K-48XXXZ
C1
330 μf, 100V
330 μf, 100V
330 μf, 100V
L
12μH
12μH
12μH
C2
100μ, 100V
100μ, 100V
100μ, 100V
C3
N/A
N/A
1000Pf, 2000V
Note B: Input filter components (C1, C2, L) are used to help meet conducted emissions requirement for the module. These components should be
mounted as close as possible to the module; and all leads should be minimized to decrease radiated noise.
NOTE: 1. Datasheets are updated as needed and as such, specifications are subject to change without notice. Once printed or downloaded, datasheets are no longer controlled
by Aimtec; refer to www.aimtec.com for the most current product specifications. 2. Product labels shown, including safety agency certifications on labels, may vary based on the
date manufactured. 3. Mechanical drawings and specifications are for reference only. 4. All specifications are measured at an ambient temperature of 25°C, humidity<75%,
nominal input voltage and at rated output load unless otherwise specified. 5. Aimtec may not have conducted destructive testing or chemical analysis on all internal components
and chemicals at the time of publishing this document. CAS numbers and other limited information are considered proprietary and may not be available for release. 6. This
product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control systems or other such applications which necessitate
specific safety and regulatory standards other the ones listed in this datasheet. 7. Warranty is in accordance with Aimtec’s standard Terms of Sale available at www.aimtec.com.
www.aimtec.com
F 051e R8.F
Tel: +1 514 620 2722
4 of 4
Toll free: + 1 888 9 AIMTEC
(924 6832)
North America only
Similar pages