LTC4000 High Voltage High Current Controller for Battery Charging and Power Management Description Features n n n n n n n n n n Complete High Performance Battery Charger When Paired with a DC/DC Converter Wide Input and Output Voltage Range: 3V to 60V Input Ideal Diode for Low Loss Reverse Blocking and Load Sharing Output Ideal Diode for Low Loss PowerPath™ and Load Sharing with the Battery Instant-On Operation with Heavily Discharged Battery Programmable Input and Charge Current: ±1% Accuracy ±0.25% Accurate Programmable Float Voltage Programmable C/X or Timer Based Charge Termination NTC Input for Temperature Qualified Charging 28-Lead 4mm × 5mm QFN or SSOP Packages The LTC®4000 is a high voltage, high performance controller that converts many externally compensated DC/DC power supplies into full-featured battery chargers. Features of the LTC4000’s battery charger include: accurate (±0.25%) programmable float voltage, selectable timer or current termination, temperature qualified charging using an NTC thermistor, automatic recharge, C/10 trickle charge for deeply discharged cells, bad battery detection and status indicator outputs. The battery charger also includes precision current sensing that allows lower sense voltages for high current applications. The LTC4000 supports intelligent PowerPath control. An external PFET provides low loss reverse current protection. Another external PFET provides low loss charging or discharging of the battery. This second PFET also facilitates an instant-on feature that provides immediate downstream system power even when connected to a heavily discharged or short faulted battery. Applications n n n n High Power Battery Charger Systems High Performance Portable Instruments Industrial Battery Equipped Devices Notebook/Subnotebook Computers The LTC4000 is available in a low profile 28-lead 4mm × 5mm QFN and SSOP packages. L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks and PowerPath is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Typical Application 48V to 10.8V at 10A Buck Converter Charger for Three LiFePO4 Cells IN 5mΩ LT3845 OUT VC SHDN 14.7k ITH 47nF CC IID IGATE CSP BAT 127k LTC4000 ENC CHRG FLT FBG 133k BFB IIMON 10nF 1.13M NTC IBMON 10nF TMR CL 0.1µF 24.9k 10k GND BIAS CX 22.1k 12 11 ICHARGE 10 8 Si7135DP OFB VM 3.0V 5mΩ CSN BGATE 1µF 1.10M 100k 1.15M 10k 1µF 10.8V FLOAT 10A MAX CHARGE CURRENT 3-CELL LiFePO4 BATTERY PACK VOUT 10.5 10 VOUT 6 9.5 4 9 2 0 8.5 ICHARGE 6 7 VOUT (V) RST CLN IN 12V, 15A 100µF Charge Current and VOUT Profile vs VBAT During a Charge Cycle ICHARGE (A) 15V TO 60V Si7135DP 8 10 9 VBAT (V) 11 8 12 4000 TA01b 4000 TA01a NTHS0603 N02N1002J 4000f 1 LTC4000 Absolute Maximum Ratings (Note 1) IN, CLN, IID, CSP, CSN, BAT........................ –0.3V to 62V IN-CLN, CSP-CSN.............................................–1V to 1V OFB, BFB, FBG............................................ –0.3V to 62V FBG.............................................................–1mA to 2mA IGATE............Max (VIID, VCSP) – 10V to Max (VIID, VCSP) BGATE........Max (VBAT, VCSN) – 10V to Max (VBAT, VCSN) ENC, CX, NTC, VM....................................–0.3V to VBIAS IL, CL, TMR, IIMON, CC............................–0.3V to VBIAS BIAS..............................................–0.3V to Min (6V, VIN) IBMON...................................–0.3V to Min (VBIAS, VCSP) ITH................................................................ –0.3V to 6V CHRG, FLT, RST........................................... –0.3V to 62V CHRG, FLT, RST...........................................–1mA to 2mA Operating Junction Temperature Range (Note 2).................................................................. 125°C Storage Temperature Range................... –65°C to 150°C Pin Configuration TOP VIEW 3 26 RST CL 4 25 VM TMR 5 24 GND GND 6 23 IN ITH CX CC 27 IIMON 28 27 26 25 24 23 CLN 28 IL 2 IN 1 IBMON GND ENC IID TOP VIEW 22 IGATE VM 1 RST 2 21 OFB IIMON 3 20 CSP IL 4 19 CSN 29 GND ENC 5 18 BGATE IBMON 6 17 BAT CX 7 16 BFB CL 8 15 FBG NTC BIAS CHRG FLT GND TMR 9 10 11 12 13 14 UFD PACKAGE 28-LEAD (4mm × 5mm) PLASTIC QFN TJMAX = 125°C, θJA = 43°C/W, θJC = 4°C/W EXPOSED PAD (PIN 29) IS GND, MUST BE SOLDERED TO PCB FLT 7 22 CLN CHRG 8 21 CC BIAS 9 20 ITH NTC 10 19 IID FBG 11 18 IGATE BFB 12 17 OFB BAT 13 16 CSP BGATE 14 15 CSN GN PACKAGE 28-LEAD PLASTIC SSOP TJMAX = 125°C, θJA = 80°C/W, θJC = 25°C/W Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC4000EUFD#PBF LTC4000EUFD#TRPBF 4000 28-Lead (4mm × 5mm) Plastic QFN –40°C to 125°C LTC4000IUFD#PBF LTC4000IUFD#TRPBF 4000 28-Lead (4mm × 5mm) Plastic QFN –40°C to 125°C LTC4000EGN#PBF LTC4000EGN#TRPBF LTC4000GN 28-Lead Plastic SSOP –40°C to 125°C LTC4000IGN#PBF LTC4000IGN#TRPBF LTC4000GN 28-Lead Plastic SSOP –40°C to 125°C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 4000f 2 LTC4000 Electrical Characteristics The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C. VIN = VCLN = 3V to 60V unless otherwise noted (Notes 2, 3). SYMBOL PARAMETER VIN Input Supply Operating Range IIN Input Quiescent Operating Current IBAT Battery Pin Operating Current Battery Only Quiescent Current CONDITIONS MIN l TYP 3 MAX 60 0.4 UNITS V mA VIN ≥ 3V, VCSN = VCSP ≥ VBAT l 50 100 µA VIN ≥ 0V, VCSN = VCSP ≥ VBAT l 10 20 μA 0.4 V Shutdown ENC Input Voltage Low l ENC Input Voltage High l 1.5 –4 –2 l 1.5 2.5 l 1.133 1.125 1.136 1.136 l 1.181 1.193 ENC Pull-Up Current VENC = 0V ENC Open Circuit Voltage VENC = Open V –0.5 µA V Voltage Regulation VBFB_REG Battery Feedback Voltage BFB Input Current VOFB_REG VBFB = 1.2V Output Feedback Voltage OFB Input Current ± 0.1 VOFB = 1.2V RFBG Ground Return Feedback Resistance VRECHRG(RISE) Rising Recharge Battery Threshold Voltage VRECHRG(HYS) Recharge Battery Threshold Voltage Hysteresis % of VBFB_REG VOUT(INST_ON) Instant-On Battery Voltage Threshold VLOBAT VLOBAT(HYS) V V µA 1.204 ± 0.1 l % of VBFB_REG 1.139 1.147 V µA 100 400 Ω 97.6 98.3 % l 96.9 % of VBFB_REG l 82 86 90 % Falling Low Battery Threshold Voltage % of VBFB_REG l 65 68 71 % Low Battery Threshold Voltage Hysteresis % of VBFB_REG Ratio of Monitored-Current Voltage to Sense Voltage VIN,CLN = 50mV, VIIMON/VIN,CLN VCSP,CSN = 50mV, VIBMON/VCSP,CSN Sense Voltage Offset VCSP,CSN = 50mV, VCSP = 60V or VIN,CLN = 50mV, VIN = 60V (Note 4) 0.5 % 3 % Current Regulation VOS l 19 20 –300 CLN Pin Current 21 V/V 300 µV ±1 µA CSP Pin Current VIGATE = Open, VIID = 0V 90 μA CSN Pin Current VBGATE = Open, VBAT = 0V 45 μA IIL Pull-Up Current for the Input Current Limit Programming Pin l –55 –50 –45 μA ICL Pull-Up Current for the Charge Current Limit Programming Pin l –55 –50 –45 μA ICL_TRKL Pull-Up Current for the Charge Current Limit Programming Pin in Trickle Charge Mode l –5.5 –5.0 –4.5 μA 40 90 140 kΩ VBFB < VLOBAT Input Current Monitor Resistance to GND 40 90 140 kΩ A4, A5 Error Amp Offset for the Current Loops VCL = 0.8V, VIL = 0.8V (See Figure 1) Charge Current Monitor Resistance to GND l –10 0 10 mV Maximum Programmable Current Limit Voltage Range l 0.985 1.0 1.015 V 4000f 3 LTC4000 Electrical Characteristics The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C. VIN = VCLN = 3V to 60V unless otherwise noted (Notes 2, 3). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Charge Termination CX Pin Pull-Up Current VCX = 0.1V l –5.5 –5.0 –4.5 µA VCX,IBMON(OS) CX Comparator Offset Voltage, IBMON Falling VCX = 0.1V l 0.5 10 25 mV VCX,IBMON(HYS) CX Comparator Hysteresis Voltage 5 mV TMR Pull-Up Current VTMR = 0V –5.0 μA TMR Pull-Down Current VTMR = 1.5V 5.0 μA TMR Pin Frequency CTMR = 0.01μF 400 500 600 Hz 2.1 2.5 V tT Charge Termination Time CTMR = 0.1μF l 2.3 2.9 3.5 h tT/tBB Ratio of Charge Terminate Time to Bad Battery CTMR = 0.1μF Indicator Time l 3.95 4 4.05 h/h VNTC(COLD) NTC Cold Threshold VNTC Rising, % of VBIAS l 73 75 77 % VNTC(HOT) NTC Hot Threshold VNTC Falling, % of VBIAS l 33 35 37 % VNTC(HYS) NTC Thresholds Hysteresis % of VBIAS VNTC(OPEN) NTC Open Circuit Voltage % of VBIAS RNTC(OPEN) NTC Open Circuit Input Resistance TMR Threshold for CX Termination l 5 l 45 50 % 55 300 % kΩ Voltage Monitoring and Open Drain Status Pins VVM(TH) VM Input Falling Threshold VVM(HYS) VM Input Hysteresis VM Input Current l 1.181 VVM = 1.2V 1.193 1.204 V 40 mV ±0.1 µA IRST,CHRG,FLT(LKG) Open Drain Status Pins Leakage Current VPIN = 60V VRST,CHRG,FLT(VOL) Open Drain Status Pins Voltage Output Low IPIN = 1mA l ±1 µA Input PowerPath Forward Regulation Voltage VIID,CSP, 3V ≤ VCSP ≤ 60V l 0.1 Input PowerPath Fast Reverse Turn-Off Threshold Voltage VIID,CSP, 3V ≤ VCSP ≤ 60V, VIGATE = VCSP – 2.5V, ∆IIGATE/∆ VIID,CSP ≥ 100μA/mV l Input PowerPath Fast Forward Turn-On Threshold Voltage VIID,CSP, 3V ≤ VCSP ≤ 60V, VIGATE = VIID – 1.5V, ∆IIGATE/∆ VIID,CSP ≥ 100μA/mV l Input Gate Turn-Off Current VIID = VCSP, VIGATE = VCSP – 1.5V –0.3 μA Input Gate Turn-On Current VCSP = VIID – 20mV, VIGATE = VIID – 1.5V 0.3 μA IIGATE(FASTOFF) Input Gate Fast Turn-Off Current VCSP = VIID + 0.1V, VIGATE = VCSP – 5V –0.5 mA IIGATE(FASTON) Input Gate Fast Turn-On Current VCSP = VIID – 0.1V, VIGATE = VIID – 1.5V 0.7 mA VIGATE(ON) Input Gate Clamp Voltage IIGATE = 2µA, VIID = 12V to 60V, VCSP = VIID – 0.5V, Measure VIID – VIGATE l 13 15 V Input Gate Off Voltage IIGATE = – 2μA, VIID = 3V to 59.9V, VCSP = VIID + 0.5V, Measure VCSP – VIGATE l 0.45 0.7 V 0.4 V 8 20 mV –90 –50 –20 mV 40 80 130 mV Input PowerPath Control 4000f 4 LTC4000 Electrical Characteristics The l denotes the specifications which apply over the full operating junction temperature range, otherwise specifications are at TA = 25°C. VIN = VCLN = 3V to 60V unless otherwise noted (Notes 2, 3). SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS Battery PowerPath Control Battery Discharge PowerPath Forward Regulation Voltage VBAT,CSN, 2.8V ≤ VBAT ≤ 60V l 0.1 8 20 mV Battery PowerPath Fast Reverse Turn-Off Threshold Voltage VBAT,CSN, 2.8V ≤ VBAT ≤ 60V, Not Charging, VBGATE = VCSN – 2.5V, ∆IBGATE/∆VBAT,CSN ≥ 100μA/mV l –90 –50 –20 mV Battery PowerPath Fast Forward Turn-On Threshold Voltage VBAT,CSN, 2.8V ≤ VCSN ≤ 60V, VBGATE = VBAT – 1.5V, ∆IBGATE/∆ VBAT,CSN ≥ 100μA/mV l 40 80 130 mV Battery Gate Turn-Off Current VBGATE = VCSN – 1.5V, VCSN ≥ VBAT, VOFB < VOUT(INST_ON) and Charging in Progress, or VCSN = VBAT and Not Charging –0.3 μA Battery Gate Turn-On Current VBGATE = VBAT – 1.5V, VCSN ≥ VBAT, VOFB > VOUT(INST_ON) and Charging in Progress, or VCSN = VBAT – 20mV 0.3 μA IBGATE(FASTOFF) Battery Gate Fast Turn-Off Current VCSN = VBAT + 0.1V and Not Charging, VBGATE = VCSN – 5V –0.5 mA IBGATE(FASTON) Battery Gate Fast Turn-On Current VCSN = VBAT – 0.1V, VBGATE = VBAT – 1.5V 0.7 mA VBGATE(ON) Battery Gate Clamp Voltage IBGATE = 2μA, VBAT = 12V to 60V, VCSN = VBAT – 0.5V, Measure VBAT – VBGATE Battery Gate Off Voltage l IBGATE = – 2μA, VBAT = 2.8V to 60V, VCSN = VBAT + 0.5V and not Charging, Measure VCSN – VBGATE l 13 15 V 0.45 0.7 V 2.9 3.5 V –10 BIAS Regulator Output and Control Pins VBIAS BIAS Output Voltage No Load ΔVBIAS BIAS Output Voltage Load Regulation IBIAS = – 0.5mA –0.5 BIAS Output Short-Circuit Current VBIAS = 0V –12 mA Transconductance of Error Amp CC = 1V 0.5 mA/V l Open Loop DC Voltage Gain of Error Amp CC = Open IITH(PULL_UP) Pull-Up Current on the ITH Pin VITH = 0V, VCC = 0V IITH(PULL_DOWN) Pull-Down Current on the ITH Pin VITH = 0.4V, CC = Open Open Loop DC Voltage Gain of ITH Driver ITH = Open Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2: The LTC4000 is tested under conditions such that TJ ≈ TA. The LTC4000E is guaranteed to meet specifications from 0°C to 85°C junction temperature. Specifications over the –40°C to 125°C operating junction temperature range are assured by design, characterization and correlation with statistical process controls. The LTC4000I is guaranteed over the full –40°C to 125°C operating junction temperature range. Note that the maximum ambient temperature consistent with these specifications is 2.4 80 –6 l 0.5 –5 % dB –4 μA 1 mA 60 dB determined by specific operating conditions in conjunction with board layout, the rated package thermal impedance and other environmental factors. The junction temperature (TJ, in °C) is calculated from the ambient temperature (TA, in °C) and power dissipation (PD, in Watts) according to the following formula: TJ = TA + (PD • θJA), where θJA (in °C/W) is the package thermal impedance. Note 3: All currents into pins are positive; all voltages are referenced to GND unless otherwise noted. Note 4: These parameters are guaranteed by design and are not 100% tested. 4000f 5 LTC4000 Typical Performance Characteristics Input Quiescent Current and Battery Quiescent Current Over Temperature 1.0 Battery Float Voltage Feedback, Output Voltage Regulation Feedback and VM Falling Threshold Over Temperature Battery Only Quiescent Current Over Temperature 100 VIN = VBAT = 15V VCSN = 15.5V IIN 1.20 1.19 VBAT = 60V 10 1.18 IBAT PIN VOLTAGE (V) 0.1 1 IBAT (µA) IIN/IBAT (mA) VBAT = 15V VBAT = 3V 0.1 0.01 1.17 VVM(TH) VOFB_REG 1.16 1.15 1.14 VBFB_REG 1.13 1.12 1.11 0 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 0.001 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4000 G01 4000 G02 Battery Thresholds: Rising Recharge, Instant-On Regulation and Falling Low Battery As a Percentage of Battery Float Feedback Over Temperature 100 –45.0 1.015 1.010 –47.5 IIL/ICL (µA) VOUT(INST_ON) 80 75 70 Maximum Programmable Current Limit Voltage Over Temperature IL and CL Pull-Up Current Over Temperature VRECHRG(RISE) 90 85 –50.0 VLOBAT –55.0 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4000 G04 0.985 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4000 G06 CX Comparator Offset Voltage with VIBMON Falling Over Temperature Current Sense Offset Voltage Over Common Mode Voltage Range 300 VMAX(IN,CLN) = VMAX(CSP, CSN) = 15V 200 100 VOS (µV) VOS(CSP, CSN) 0 VOS(IN, CSN) VOS(CSP, CSN) 0 VOS(IN, CSN) –100 –200 –200 –300 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) –300 4000 G07 VCX,IBMON (mV) 200 VOS (µV) 0.995 4000 G05 Current Sense Offset Voltage Over Temperature –100 1.000 0.990 60 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 100 1.005 –52.5 65 300 4000 G03 VIIMON /VIBMON (V) PERCENT OF VBFB_REG (%) 95 1.10 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 0 10 20 30 40 50 VMAX(IN, CLN) /VMAX(CSP, CSN) (V) 60 4000 G08 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4000 G09 4000f 6 LTC4000 Typical Performance Characteristics Charge Termination Time with 0.1µF Timer Capacitor Over Temperature 3.5 80 VNTC(COLD) 75 3.3 14 12 2.9 2.7 65 60 55 VNTC(OPEN) 50 45 VNTC(HOT) 40 2.5 VIID,CSP / VBAT,CSN (mV) PERCENT OF VBIAS (%) 70 3.1 TT (h) PowerPath Forward Voltage Regulation Over Temperature NTC Thresholds Over Temperature VIGATE (ON)/VBGATE(ON) (V) 0 –30 14.0 13.5 13.0 12.5 12.0 –60 11.5 –90 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 11.0 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4000 G13 4000 G14 BIAS Voltage at 0.5mA Load Over Temperature 1.5 1.4 3.1 VIN = 3V 2.7 450 400 350 300 250 200 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) ITH Pull-Down Current vs VITH 2.0 1.2 1.1 1.0 0.9 0.8 0.7 2.6 500 2.5 VITH = 0.4V 1.3 IITH(PULL-DOWN) (mA) VBIAS (V) VIN = 15V VCSP = VCSN = 15V 550 ITH Pull-Down Current Over Temperature 3.2 VIN = 60V 600 4000 G15 IITH(PULL-DOWN) (mA) VIID,CSP /VBAT,CSN (mV) VIID = VBAT = 15V 14.5 30 2.8 PowerPath Turn-Off Gate Voltage Over Temperature VMAX(IID,CSP), IGATE/VMAX(BAT,CSN),BGATE (mV) 15.0 VIID = VBAT = 15V 2.9 4000 G12 PowerPath Turn-On Gate Clamp Voltage Over Temperature 90 3.0 4 4000 G11 PowerPath Fast Off, Fast On and Forward Regulation Over Temperature 60 VIID = VBAT = 60V 6 0 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 30 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4000 G10 120 VIID = VBAT = 3V 8 2 35 2.3 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) VIID = VBAT = 15V 10 1.5 1.0 0.5 0.6 2.5 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4000 G16 0.5 –60 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 4000 G17 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 VITH (V) 1 4000 G18 4000f 7 LTC4000 Pin Functions (QFN/SSOP) VM (Pin 1/Pin 25): Voltage Monitor Input. High impedance input to an accurate comparator with a 1.193V threshold (typical). This pin controls the state of the RST output pin. Connect a resistor divider (RVM1, RVM2) between the monitored voltage and GND, with the center tap point connected to this pin. The falling threshold of the monitored voltage is calculated as follows: VVM _ RST = RVM1 + RVM2 • 1.193V RVM2 where RVM2 is the bottom resistor between the VM pin and GND. Tie to the BIAS pin if voltage monitoring function is not used. RST (Pin 2/Pin 26): High Voltage Open Drain Reset Output. When the voltage at the VM pin is below 1.193V, this status pin is pulled low. When driven low, this pin can disable a DC/DC converter when connected to the converter’s enable pin. This pin can also drive an LED to provide a visual status indicator of a monitored voltage. Short this pin to GND when not used. IIMON (Pin 3/Pin 27): Input Current Monitor. The voltage on this pin is 20 times (typical) the sense voltage (VIN,CLN) across the input current sense resistor(RIS), therefore providing a voltage proportional to the input current. Connect an appropriate capacitor to this pin to obtain a voltage representation of the time-average input current. Short this pin to GND to disable input current limit feature. IL (Pin 4/Pin 28): Input Current Limit Programming. Connect the input current programming resistor (RIL) to this pin. This pin sources 50µA of current. The regulation loop compares the voltage on this pin with the input current monitor voltage (VIIMON), and drives the ITH pin accordingly to ensure that the programmed input current limit is not exceeded. The input current limit is determined using the following formula: ENC (Pin 5/Pin 1): Enable Charging Pin. High impedance digital input pin. Pull this pin above 1.5V to enable charging and below 0.5V to disable charging. Leaving this pin open causes the internal 1µA pull-up current to pull the pin to 2.5V (typical). IBMON (Pin 6/Pin 2): Battery Charge Current Monitor. The voltage on this pin is 20 times (typical) the sense voltage (VCSP,CSN) across the battery current sense resistor (RCS), therefore providing a voltage proportional to the battery charge current. Connect an appropriate capacitor to this pin to obtain a voltage representation of the time-average battery charge current. Short this pin to GND to disable charge current limit feature. CX (Pin 7/Pin 3): Charge Current Termination Programming. Connect the charge current termination programming resistor (RCX) to this pin. This pin is a high impedance input to a comparator and sources 5μA of current. When the voltage on this pin is greater than the charge current monitor voltage (VIBMON), the CHRG pin turns high impedance indicating that the CX threshold is reached. When this occurs, the charge current is immediately terminated if the TMR pin is shorted to the BIAS pin, otherwise charging continues until the charge termination timer expires. The charge current termination value is determined using the following formula: IC / X = (0.25µA • R CX ) − 0.5mV R CS Where RCS is the sense resistor connected to the CSP and the CSN pins. Note that if RCX = RCL ≤ 19.1kΩ, where RCL is the charge current programming resistor, then the charge current termination value is one tenth the full charge current, more familiarly known as C/10. Short this pin to GND to disable CX termination. ⎛R ⎞ IILIM = 2.5µA • ⎜ IL ⎟ ⎝ RIS ⎠ where RIS is the sense resistor connected to the IN and the CLN pins. Leave the pin open for the maximum input current limit of 50mV/RIS. 4000f 8 LTC4000 Pin Functions (QFN/SSOP) CL (Pin 8/Pin 4): Charge Current Limit Programming. Connect the charge current programming resistor (RCL) to this pin. This pin sources 50µA of current. The regulation loop compares the voltage on this pin with the charge current monitor voltage (VIBMON), and drives the ITH pin accordingly to ensure that the programmed charge current limit is not exceeded. The charge current limit is determined using the following formula: ICLIM ⎛R ⎞ = 2.5µA • ⎜ CL ⎟ ⎝ RCS ⎠ Where RCS is the sense resistor connected to the CSP and the CSN pins. Leave the pin open for the maximum charge current limit of 50mV/RCS. TMR (Pin 9/Pin 5): Charge Timer. Attach 1nF of external capacitance (CTMR) to GND for each 104 seconds of charge termination time and 26 seconds of bad battery indicator time. Short to GND to prevent bad battery indicator time and charge termination time from expiring – allowing a continuous trickle charge and top off float voltage regulation charge. Short to BIAS to disable bad battery detect and enable C/X charging termination. GND (Pins 10, 28, 29/Pins 6, 24): Device Ground Pins. Connect the ground pins to a suitable PCB copper ground plane for proper electrical operation. The QFN package exposed pad must be soldered to PCB ground for rated thermal performance. FLT, CHRG (Pin 11, Pin 12/Pin 7, Pin 8): Charge Status Indicator Pins. These pins are high voltage open drain pull down pins. The FLT pin pulls down when there is an under or over temperature condition during charging or when the voltage on the BFB pin stays below the low battery threshold during charging for a period longer than the bad battery indicator time. The CHRG pin pulls down during a charging cycle. Please refer to the application information section for details on specific modes indicated by the combination of the states of these two pins. Pull up each of these pins with an LED in series with a resistor to a voltage source to provide a visual status indicator. Short these pins to GND when not used. BIAS (Pin 13/Pin 9): 2.9V Regulator Output. Connect a capacitor of at least 470nF to bypass this 2.9V regulated voltage output. Use this pin to bias the resistor divider to set up the voltage at the NTC pin. NTC (Pin 14/Pin 10): Thermistor Input. Connect a thermistor from NTC to GND, and a corresponding resistor from BIAS to NTC. The voltage level on this pin determines if the battery temperature is safe for charging. The charge current and charge timer are suspended if the thermistor indicates a temperature that is unsafe for charging. Once the temperature returns to the safe region, charging resumes. Leave the pin open or connected to a capacitor to disable the temperature qualified charging function. FBG (Pin 15/Pin 11): Feedback Ground Pin. This is the ground return pin for the resistor dividers connected to the BFB and OFB pins. As soon as the voltage at IN is valid (>3V typical), this pin has a 100Ω resistance to GND. When the voltage at IN is not valid, this pin is disconnected from GND to ensure that the resistor dividers connected to the BFB and OFB pins do not continue to drain the battery when the battery is the only available power source. BFB (Pin 16/Pin 12): Battery Feedback Voltage Pin. This pin is a high impedance input pin used to sense the battery voltage level. In regulation, the battery float voltage loop sets the voltage on this pin to 1.136V (typical). Connect this pin to the center node of a resistor divider between the BAT pin and the FBG pin to set the battery float voltage. The battery float voltage can then be obtained as follows: VFLOAT = RBFB2 + RBFB1 • 1.136V RBFB2 BAT (Pin 17/Pin 13): Battery Pack Connection. Connect the battery to this pin. This pin is the anode of the battery ideal diode driver (the cathode is the CSN pin). 4000f 9 LTC4000 Pin Functions (QFN/SSOP) BGATE (Pin 18/Pin 14): External Battery PMOS Gate Drive Output. When not charging, the BGATE pin drives the external PMOS to behave as an ideal diode from the BAT pin (anode) to the CSN pin (cathode). This allows efficient delivery of any required additional power from the battery to the downstream system connected to the CSN pin. When charging a heavily discharged battery, the BGATE pin is regulated to set the output feedback voltage (OFB pin) to 86% of the battery float voltage (0.974V typical). This allows the instant-on feature, providing an immediate valid voltage level at the output when the LTC4000 is charging a heavily discharged battery. Once the voltage on the OFB pin is above the 0.974V typical value, then the BGATE pin is driven low to ensure an efficient charging path from the CSN pin to the BAT pin. CSN (Pin 19/Pin 15): Charge Current Sense Negative Input and Battery Ideal Diode Cathode. Connect a sense resistor between this pin and the CSP pin. The LTC4000 senses the voltage across this sense resistor and regulates it to a voltage equal to 1/20th (typical) of the voltage set at the CL pin. The maximum regulated sense voltage is 50mV. The CSN pin is also the cathode input of the battery ideal diode driver (the anode input is the BAT pin). Tie this pin to the CSP pin if no charge current limit is desired. Refer to the Applications Information section for complete details. CSP (Pin 20/Pin 16): Charge Current Sense Positive Input and Input Ideal Diode Cathode. Connect a sense resistor between this pin and the CSN pin for charge current sensing and regulation. This input should be tied to CSN to disable the charge current regulation function. This pin is also the cathode of the input ideal diode driver (the anode is the IID pin). OFB (Pin 21/Pin 17): Output Feedback Voltage Pin. This pin is a high impedance input pin used to sense the output voltage level. In regulation, the output voltage loop sets the voltage on this feedback pin to 1.193V. Connect this pin to the center node of a resistor divider between the CSP pin and the FBG pin to set the output voltage when battery charging is terminated and all the output load current is provided from the input. The output voltage can then be obtained as follows: VOUT = ROFB2 + ROFB1 • 1.193V ROFB2 When charging a heavily discharged battery (such that VOFB < VOUT(INST_ON)), the battery PowerPath PMOS connected to BGATE is regulated to set the voltage on this feedback pin to 0.974V (approximately 86% of the battery float voltage). The instant-on output voltage is then as follows: VOUT(INST _ ON) = ROFB2 + ROFB1 • 0.974V ROFB2 IGATE (Pin 22/Pin 18): Input PMOS Gate Drive Output. The IGATE pin drives the external PMOS to behave as an ideal diode from the IID pin (anode) to the CSP pin (cathode). IID (Pin 23/Pin 19): Input Ideal Diode Anode. This pin is the anode of the input ideal diode driver (the cathode is the CSP pin). ITH (Pin 24/Pin 20): High Impedance Control Voltage Pin. When any of the regulation loops (input current, charge current, battery float voltage or the output voltage) indicate that its limit is reached, the ITH pin will sink current (up to 1mA) to regulate that particular loop at the limit. In many applications, this ITH pin is connected to the control/compensation node of a DC/DC converter. Without any external pull-up, the operating voltage range on this pin is GND to 2.5V. With an external pull-up, the voltage on this pin can be pulled up to 6V. Note that the impedance connected to this pin affects the overall loop gain. For details, refer to the Applications Information section. 4000f 10 LTC4000 Pin Functions (QFN/SSOP) CC (Pin 25/Pin 21): Converter Compensation Pin. Connect an R-C network from this pin to the ITH pin to provide a suitable loop compensation for the converter used. Refer to the Applications Information section for discussion and procedure on choosing an appropriate R-C network for a particular DC/DC converter. CLN (Pin 26/Pin 22): Input Current Sense Negative Input. Connect a sense resistor between this pin and the IN pin. The LTC4000 senses the voltage across this sense resistor and regulates it to a voltage equal to 1/20th (typical) of the voltage set at the IL pin. Tie this pin to the IN pin if no input current limit is desired. Refer to the Applications Information section for complete details. IN (Pin 27/Pin 23): Input Supply Voltage: 3V to 60V. Supplies power to the internal circuitry and the BIAS pin. Connect the power source to the downstream system and the battery charger to this pin. This pin is also the positive sense pin for the input current limit. Connect a sense resistor between this pin and the CLN pin. Tie this pin to CLN if no input current limit is desired. A local 0.1µF bypass capacitor to ground is recommended on this pin. 4000f 11 LTC4000 Block Diagram RIS CIN RVM1 OUT DC/DC CONVERTER CCLN RC IN CLN RST VM – CIBMON CC ITH CC IID IBMON IGATE CSP CP1 RVM2 1.193V 8mV + + – – + A8 gm = 0.33m A9 gm = 0.33m 60k A1 +– IIMON 8mV gm A11 50µA RIL A4 IL 1V + –gm – gm– BIAS A5 – CBIAS ROFB1 5µA/ 50µA 1V gm+ CL – A7 + – IN LDO, BG, REF BATTERY IDEAL DIODE AND INSTANT-ON DRIVER ITH AND CC DRIVER A10 BGATE ENABLE CHARGING 0.974V 60k RCS CSN LINEAR GATE DRIVER AND VOLTAGE CLAMP A2 INPUT IDEAL DIODE DRIVER BIAS A6 + – REF gm RCL OFB gm BIAS OFB 1.193V CP6 BFB – 0.771V ROFB2 1.136V + BFB + CP4 TOO COLD – – RBFB2 1.109V FBG NTC FAULT + RBFB1 + CP5 NTC SYSTEM LOAD CL CIID – + IN LOGIC CP3 – CP2 BAT – BIAS TOO HOT + CBAT 5µA 10mV –+ BIAS + – RNTC CX BATTERY PACK 2µA TMR CTMR RCX OSCILLATOR GND ENC CHRG FLT 4000 BD R3 Figure 1. LTC4000 Functional Block Diagram 4000f 12 LTC4000 Operation Overview The LTC4000 is designed to simplify the conversion of any externally compensated DC/DC converter into a high performance battery charger with PowerPath control. It only requires the DC/DC converter to have a control or external-compensation pin (usually named VC or ITH) whose voltage level varies in a positive monotonic way with its output. The output variable can be either output voltage or output current. For the following discussion, refer to the Block Diagram in Figure 1. The LTC4000 includes four different regulation loops: input current, charge current, battery float voltage and output voltage (A4-A7). Whichever loop requires the lowest voltage on the ITH pin for its regulation controls the external DC/DC converter. The input current regulation loop ensures that the programmed input current limit (using a resistor at IL) is not exceeded at steady state. The charge current regulation loop ensures that the programmed battery charge current limit (using a resistor at CL) is not exceeded. The float voltage regulation loop ensures that the programmed battery stack voltage (using a resistor divider from BAT to FBG via BFB) is not exceeded. The output voltage regulation loop ensures that the programmed system output voltage (using a resistor divider from CSP to FBG via OFB) is not exceeded. The LTC4000 also provides monitoring pins for the input current and charge current at the IIMON and IBMON pins respectively. The LTC4000 features an ideal diode controller at the input from the IID pin to the CSP pin and a PowerPath controller at the output from the BAT pin to the CSN pin. The output PowerPath controller behaves as an ideal diode controller when not charging. When charging, the output PowerPath controller has two modes of operation. If VOFB is greater than VOUT(INST_ON), BGATE is driven low. When VOFB is less than VOUT(INST_ON), a linear regulator implements the instant-on feature. This feature provides regulation of the BGATE pin so that a valid voltage level is immediately available at the output when the LTC4000 is charging an over-discharged, dead or short faulted battery. The state of the ENC pin determines whether charging is enabled. When ENC is grounded, charging is disabled and the battery float voltage loop is disabled. Charging is enabled when the ENC pin is left floating or pulled high (≥1.5V) The LTC4000 offers several user configurable battery charge termination schemes. The TMR pin can be configured for either C/X termination, charge timer termination or no termination. After a particular charge cycle terminates, the LTC4000 features an automatic recharge cycle if the battery voltage drops below 97.6% of the programmed float voltage. Trickle charge mode drops the charge current to one tenth of the normal charge current (programmed using a resistor from the CL pin to GND) when charging into an over discharged or dead battery. When trickle charging, a capacitor on the TMR pin can be used to program a time out period. When this bad battery timer expires and the battery voltage fails to charge above the low battery threshold (VLOBAT), the LTC4000 will terminate charging and indicate a bad battery condition through the status pins (FLT and CHRG). The LTC4000 also includes an NTC pin, which provides temperature qualified charging when connected to an NTC thermistor thermally coupled to the battery pack. To enable this feature, connect the thermistor between the NTC and the GND pins, and a corresponding resistor from the BIAS pin to the NTC pin. The LTC4000 also provides a charging status indicator through the FLT and the CHRG pins. Aside from biasing the thermistor-resistor network, the BIAS pin can also be used for a convenient pull up voltage. This pin is the output of a low dropout voltage regulator that is capable of providing up to 0.5mA of current. The regulated voltage on the BIAS pin is available as soon as the IN pin is within its operating range (≥3V). Input Ideal Diode The input ideal diode feature provides low loss conduction and reverse blocking from the IID pin to the CSP pin. This reverse blocking prevents reverse current from the output (CSP pin) to the input (IID pin) which causes unnecessary drain on the battery and in some cases may result in unexpected DC/DC converter behavior. 4000f 13 LTC4000 Operation The ideal diode behavior is achieved by controlling an external PMOS connected to the IID pin (drain) and the CSP pin (source). The controller (A1) regulates the external PMOS by driving the gate of the PMOS device such that the voltage drop across IID and CSP is 8mV (typical). When the external PMOS ability to deliver a particular current with an 8mV drop across its source and drain is exceeded, the voltage at the gate clamps at VIGATE(ON) and the PMOS behaves like a fixed value resistor (RDS(ON)). Input Current Regulation and Monitoring One of the loops driving the ITH and CC pins is the input current regulation loop (Figure 2). This loop prevents the input current sensed through the input current sense resistor (RIS) from exceeding the programmed input current limit. RIS IN LOAD CCLN (OPTIONAL) A8 IN CLN + – CIN A8 gm = 0.33m IIMON BIAS CIIMON (OPTIONAL) LTC4000 60k 50µA RIL 1V IL CC + – – A4 CC – + RC ITH TO DC/DC 4000 FO2 Figure 2. Input Current Regulation Loop Battery Charger Overview In addition to the input current regulation loop, the LTC4000 regulates charge current, battery voltage and output voltage. When a battery charge cycle begins, the battery charger first determines if the battery is over-discharged. If the battery feedback voltage is below VLOBAT, an automatic trickle charge feature uses the charge current regulation loop to set the battery charge current to 10% of the programmed full scale value. If the TMR pin is connected to a capacitor or open, the bad battery detection timer is enabled. When this bad battery detection timer expires and the battery voltage is still below VLOBAT, the battery charger automatically terminates and indicates, via the FLT and CHRG pins, that the battery was unresponsive to charge current. Once the battery voltage is above VLOBAT, the charge current regulation loop begins charging in full power constantcurrent mode. In this case, the programmed full charge current is set with a resistor on the CL pin. Depending on available input power and external load conditions, the battery charger may not be able to charge at the full programmed rate. The external load is always prioritized over the battery charge current. The input current limit programming is always observed, and only additional power is available to charge the battery. When system loads are light, battery charge current is maximized. Once the float voltage is achieved, the battery float voltage regulation loop takes over from the charge current regulation loop and initiates constant voltage charging. In constant voltage charging, charge current slowly declines. Charge termination can be configured with the TMR pin in several ways. If the TMR pin is tied to the BIAS pin, C/X termination is selected. In this case, charging is terminated when constant voltage charging reduces the charge current to the C/X level programmed at the CX pin. Connecting a capacitor to the TMR pin selects the charge timer termination and a charge termination timer is started at the beginning of constant voltage charging. Charging terminates when the termination timer expires. When continuous charging at the float voltage is desired, tie the TMR pin to GND to disable termination. Upon charge termination, the PMOS connected to BGATE behaves as an ideal diode from BAT to CSN. The diode function prevents charge current but provides current to the system load as needed. If the system load can be completely supplied from the input, the battery PMOS turns off. While terminated, if the input current limit is not in regulation, the output voltage regulation loop takes over to ensure that the output voltage at CSP remains in control. The output voltage regulation loop regulates the voltage at the CSP pin such that the output feedback voltage at the OFB pin is 1.193V. If the system load requires more power than is available from the input, the battery ideal diode controller provides supplemental power from the battery. When the battery voltage discharges below 97.1% of the float voltage (VBFB < VRECHRG(FALL)), the automatic recharge feature initiates a new charge cycle. 4000f 14 LTC4000 Operation Charge Current Regulation The first loop involved in a normal charging cycle is the charge current regulation loop (Figure 3). As with the input current regulation loop, this loop also drives the ITH and CC pins. This loop ensures that the charge current sensed through the charge current sense resistor (RCS) does not exceed the programmed full charge current. + – IBMON CSN LTC4000 A9 gm = 0.33m 60k BIAS RCL BFB + – FBG 1.136V A6 CC CC – + RC ITH TO DC/DC Figure 4. Battery Float Voltage Regulation Loop with FBG ROFB1 CSP LTC4000 4000 FO4 BAT PMOS CCSP CIBMON (OPTIONAL) RBFB2 BAT TO SYSTEM RIS CSP RBFB1 50µA AT NORMAL 1V 5µA AT TRICKLE ROFB2 CSP LTC4000 OFB + – FBG 1.193V A7 CC CC – + RC ITH TO DC/DC CC + – – A5 CC – + 4000 FO5 RC ITH TO DC/DC CL 4000 FO3 Figure 3. Charge Current Regulation Loop Battery Voltage Regulation Once the float voltage is reached, the battery voltage regulation loop takes over from the charge current regulation loop (Figure 4). The float voltage level is programmed using the feedback resistor divider between the BAT pin and the FBG pin with the center node connected to the BFB pin. Note that the ground return of the resistor divider is connected to the FBG pin. The FBG pin disconnects the resistor divider load when VIN < 3V to ensure that the float voltage resistor divider does not consume battery current when the battery is the only available power source. For VIN ≥ 3V, the typical resistance from the FBG pin to GND is 100Ω. Output Voltage Regulation When charging terminates and the system load is completely supplied from the input, the PMOS connected to BGATE is turned off. In this scenario, the output voltage regulation loop takes over from the battery float voltage regulation loop (Figure 5). The output voltage regulation loop regulates the voltage at the CSP pin such that the output feedback voltage at the OFB pin is 1.193V. Figure 5. Output Voltage Regulation Loop with FBG Battery Instant-On and Ideal Diode The LTC4000 controls the external PMOS connected to the BGATE pin with a controller similar to the input ideal diode controller driving the IGATE pin. When not charging, the PMOS behaves as an ideal diode between the BAT (anode) and the CSN (cathode) pins. The controller (A2) regulates the external PMOS to achieve low loss conduction by driving the gate of the PMOS device such that the voltage drop from the BAT pin to the CSN pin is 8mV. When the ability to deliver a particular current with an 8mV drop across the PMOS source and drain is exceeded, the voltage at the gate clamps at VBGATE(ON) and the PMOS behaves like a fixed value resistor (RDS(ON)). The ideal diode behavior allows the battery to provide current to the load when the input supply is in current limit or the DC/DC converter is slow to react to an immediate load increase at the output. In addition to the ideal diode behavior, BGATE also allows current to flow from the CSN pin to the BAT pin during charging. There are two regions of operation when current is flowing from the CSN pin to the BAT pin. The first is when charging into a battery whose voltage is below the instant-on threshold (VOFB < VOUT(INST_ON)). In this region of operation, the controller regulates the voltage at the CSP pin 4000f 15 LTC4000 Operation to be approximately 86% of the final float voltage level (VOUT(INST_ON)). This feature provides a CSP voltage significantly higher than the battery voltage when charging into a heavily discharged battery. This instant-on feature allows the LTC4000 to provide sufficient voltage at the output (CSP pin), independent of the battery voltage. The second region of operation is when the battery feedback voltage is greater than or equal to the instant-on threshold (VOUT(INST_ON)). In this region, the BGATE pin is driven low and clamped at VBGATE(ON) to allow the PMOS to turn completely on, reducing any power dissipation due to the charge current. Battery Temperature Qualified Charging The battery temperature is measured by placing a negative temperature coefficient (NTC) thermistor close to the battery pack. The comparators CP3 and CP4 implement the temperature detection as shown in the Block Diagram in Figure 1. The rising threshold of CP4 is set at 75% of VBIAS (cold threshold) and the falling threshold of CP3 is set at 35% of VBIAS (hot threshold). When the voltage at the NTC pin is above 75% of VBIAS or below 35% of VBIAS then the LTC4000 pauses any charge cycle in progress. When the voltage at the NTC pin returns to the range of 40% to 70% of VBIAS, charging resumes. When charging is paused, the external charging PMOS turns off and charge current drops to zero. If the LTC4000 is charging in the constant voltage mode and the charge termination timer is enabled, the timer pauses until the thermistor indicates a return to a valid temperature. If the battery charger is in the trickle charge mode and the bad battery detection timer is enabled, the bad battery timer pauses until the thermistor indicates a return to a valid temperature. Input UVLO and Voltage Monitoring The regulated voltage on the BIAS pin is available as soon as VIN ≥ 3V. When VIN ≥ 3V, the FBG pin is pulled low to GND with a typical resistance of 100Ω and the rest of the chip functionality is enabled. When the IN pin is high impedance and a battery is connected to the BAT pin, the BGATE pin is pulled down with a 2μA (typical) current source to hold the battery PMOS gate voltage at VBGATE(ON) below VBAT. This allows the battery to power the output. The total quiescent current consumed by LTC4000 from the battery when IN is not valid is typically ≤ 10µA. Besides the internal input UVLO, the LTC4000 also provides voltage monitoring through the VM pin. The RST pin is pulled low when the voltage on the VM pin falls below 1.193V (typical). On the other hand, when the voltage on the VM pin rises above 1.233V (typical), the RST pin is high impedance. One common use of this voltage monitoring feature is to ensure that the converter is turned off when the voltage at the input is below a certain level. In this case, connect the RST pin to the DC/DC converter chip select or enable pin (see Figure 6). RIS IN RVM1 IN VM IN CLN – DC/DC CONVERTER EN RST CP1 RVM2 1.193V + LTC4000 4000 FO6 Figure 6. Input Voltage Monitoring with RST Connected to the EN Pin of the DC/DC Converter 4000f 16 LTC4000 Applications Information Input Ideal Diode PMOS Selection The input external PMOS is selected based on the expected maximum current, power dissipation and reverse voltage drop. The PMOS must be able to withstand a gate to source voltage greater than VIGATE(ON) (15V maximum) or the maximum regulated voltage at the IID pin, whichever is less. A few appropriate external PMOS for a number of different requirements are shown at Table 1. Table 1. PMOS RDS(ON) AT VGS = 10V (Ω) MAX ID (A) SiA923EDJ 0.054 4.5 –20 Vishay Si9407BDY 0.120 4.7 –60 Vishay Si4401BDY 0.014 10.5 –40 Vishay Si4435DDY 0.024 11.4 –30 Vishay SUD19P06-60 0.060 18.3 –60 Vishay Si7135DP 0.004 60 –30 Vishay PART NUMBER MAX VDS (V) MANUFACTURER Note that in general the larger the capacitance seen on the IGATE pin, the slower the response of the ideal diode driver. The fast turn off and turn on current is limited to –0.5mA and 0.7mA typical respectively (IIGATE(FASTOFF) and IIGATE(FASTON)). If the driver can not react fast enough to a sudden increase in load current, most of the extra current is delivered through the body diode of the external PMOS. This increases the power dissipation momentarily. It is important to ensure that the PMOS is able to withstand this momentary increase in power dissipation. Input Current Limit Setting and Monitoring The regulated input current limit is set using a resistor at the IL pin according to the following formula: RIS = VIL 20 • IILIM The input current through the sense resistor is available for monitoring through the IIMON pin. The voltage on the IIMON pin varies with the current through the sense resistor as follows: VIIMON = 20 • IRIS • RIS = 20 • ( VIN – VCLN ) The regulation voltage level at the IIMON pin is clamped at 1V with an accurate internal reference. At 1V on the IIMON pin, the input current limit is regulated at the following value: IILIM(MAX)(A) = 0.050V RIS (Ω) When this maximum current limit is desired, leave the IL pin open or set it to a voltage >1.05V such that amplifier A4 can regulate the IIMON voltage accurately to the internal reference of 1V. If the input current is noisy, add a filter capacitor to the CLN pin to reduce the AC content. For example, when using a buck DC/DC converter, the use of a CCLN capacitor is strongly recommended. Where the highest accuracy is important, pick the value of CCLN such that the AC content is less than or equal to 50% of the average voltage across the sense resistor. The voltage on the IIMON pin can be filtered further by putting a capacitor on the pin (CIIMON). The voltage on the IIMON pin is also the feedback input to the input current regulation error amplifier. Any capacitor connected to this pin places a pole in the input current regulation loop. Therefore, this filter capacitor should NOT be arbitrarily large as it will slow down the overall compensated loop. For details on loop compensation please refer to the Compensation section. where VIL is the voltage on the IL pin. The IL pin is internally pulled up with an accurate current source of 50µA. Therefore an equivalent formula to obtain the input current limit is: RIL = ILIM • RIS R ⇒ IILIM = IL • 2.5µA 2.5µA RIS 4000f 17 LTC4000 Applications Information Charge Current Limit Setting and Monitoring The regulated full charge current is set according to the following formula: RCS VCL = 20 • ICLIM where VCL is the voltage on the CL pin. The CL pin is internally pulled up with an accurate current source of 50µA. Therefore, an equivalent formula to obtain the input current limit is: RCL •R I R = CLIM CS ⇒ ICLIM = CL • 2.5µA 2.5µA RCS The charge current through the sense resistor is available for monitoring through the IBMON pin. The voltage on the IBMON pin varies with the current through the sense resistor as follows: VIBMON = 20 • IRCS • RCS = 20 • ( VCSP – VCSN ) Similar to the IIMON pin, the regulation voltage level at the IBMON pin is clamped at 1V with an accurate internal reference. At 1V on the IBMON pin, the charge current limit is regulated to the following value: 0.050V ICLIM(MAX)(A) = RCS (Ω) When this maximum charge current limit is desired, leave the CL pin open or set it to a voltage >1.05V such that amplifier A5 can regulate the IBMON pin voltage accurately to the internal reference of 1V. When the output current waveform of the DC/DC converter or the system load current is noisy, it is recommended that a capacitor is connected to the CSP pin (CCSP). This is to reduce the AC content of the current through the sense resistor (RCS). Where the highest accuracy is important, pick the value of CCSP such that the AC content is less than or equal to 50% of the average voltage across the sense resistor. Similar to the IIMON pin, the voltage on the IBMON pin is filtered further by putting a capacitor on the pin (CIBMON). This filter capacitor should not be arbitrarily large as it will slow down the overall compensated charge current regulation loop. For details on the loop compensation, refer to the Compensation section. Battery Float Voltage Programming When the value of RBFB1 is much larger than 100Ω, the final float voltage is determined using the following formula: ⎛V ⎞ RBFB1 = ⎜ FLOAT – 1⎟RBFB2 ⎝ 1.136V ⎠ When higher accuracy is important, a slightly more accurate final float voltage can be determined using the following formula: ⎛R ⎞ ⎛R ⎞ +R VFLOAT = ⎜ BFB1 BFB2 • 1.136V ⎟ – ⎜ BFB1 • VFBG ⎟ RBFB2 ⎝ ⎠ ⎝ RBFB2 ⎠ where VFBG is the voltage at the FBG pin during float voltage regulation, which accounts for all the current from all resistor dividers that are connected to this pin (RFBG = 100Ω typical). Low Battery Trickle Charge Programming and Bad Battery Detection When charging into an over-discharged or dead battery (VBFB < VLOBAT), the pull-up current at the CL pin is reduced to 10% of the normal pull-up current. Therefore, the trickle charge current is set using the following formula: RCL = ICLIM(TRKL) • RCS 0.25µA ⇒ ICLIM(TRKL) = 0.25µA • RCL RCS Therefore, when 50µA•RCL is less than 1V, the following relation is true: ICLIM(TRKL) = ICLIM 10 Once the battery voltage rises above the low battery voltage threshold, the charge current level rises from the trickle charge current level to the full charge current level. The LTC4000 also features bad battery detection. This detection is disabled if the TMR pin is grounded or tied to BIAS. However, when a capacitor is connected to the 4000f 18 LTC4000 Applications Information TMR pin, a bad battery detection timer is started as soon as trickle charging starts. If at the end of the bad battery detection time the battery voltage is still lower than the low battery threshold, charging is terminated and the part indicates a bad battery condition by pulling the FLT pin low and leaving the CHRG pin high impedance. The bad battery detection time can be programmed according to the following formula: CTMR (nF) = tBADBAT (h) • 138.5 Note that once a bad battery condition is detected, the condition is latched. In order to re-enable charging, remove the battery and connect a new battery whose voltage causes BFB to rise above the recharge battery threshold (VRECHRG(RISE)). Alternatively toggle the ENC pin or remove and reapply power to IN. C/X Detection, Charge Termination and Automatic Recharge Once the constant voltage charging is reached, there are two ways in which charging can terminate. If the TMR pin is tied to BIAS, the battery charger terminates as soon as the charge current drops to the level programmed by the CX pin. The C/X current termination level is programmed according to the following formula: RCX = IC/ X • RCS (0.25µA • RCX ) − 0.5mV + 0.5mV ⇒ IC/X = 0.25µA RCS where RCS is the charge current sense resistor connected between the CSP and the CSN pins. When the voltage at BFB is higher than the recharge threshold (97.6% of float), the C/X comparator is enabled. In order to ensure proper C/X termination coming out of a paused charging condition, connect a capacitor on the CX pin according to the following formula: CCX = 100CBGATE where CBGATE is the total capacitance connected to the BGATE pin. For example, a typical capacitance of 1nF requires a capacitor greater than 100nF connected to the CX pin to ensure proper C/X termination behavior. If a capacitor is connected to the TMR pin, as soon as the constant voltage charging is achieved, a charge termination timer is started. When the charge termination timer expires, the charge cycle terminates. The total charge termination time can be programmed according to the following formula: CTMR (nF) = t TERMINATE (h) • 34.6 If the TMR pin is grounded, charging never terminates and the battery voltage is held at the float voltage. Note that regardless of which termination behavior is selected, the CHRG and FLT pins will both assume a high impedance state as soon as the charge current falls below the programmed C/X level. After the charger terminates, the LTC4000 automatically restarts another charge cycle if the battery feedback voltage drops below 97.1% of the programmed final float voltage (VRECHRG(FALL)). When charging restarts, the CHRG pin pulls low and the FLT pin remains high impedance. Output Voltage Regulation Programming The output voltage regulation level is determined using the following formula: ⎛V ⎞ ROFB1 = ⎜ OUT − 1⎟ • ROFB2 ⎝ 1.193 ⎠ As in the battery float voltage calculation, when higher accuracy is important, a slightly more accurate output is determined using the following formula: ⎛R ⎞ ⎞ ⎛R +R VOUT = ⎜ OFB1 OFB2 • 1.193V ⎟ – ⎜ OFB1 • VFBG ⎟ ROFB2 ⎝ ⎠ ⎠ ⎝ ROFB2 where VFBG is the voltage at the FBG pin during output voltage regulation, which accounts for all the current from all resistor dividers that are connected to this pin. 4000f 19 LTC4000 Applications Information Battery Instant-On and Ideal Diode External PMOS Consideration On the other hand, when the battery voltage is above the low battery threshold but still below the instant-on threshold, the power dissipation can be calculated as follows: The instant-on voltage level is determined using the following formula: PINST _ ON = [0.86 • VFLOAT – VBAT ] • ICLIM ROFB1 + ROFB2 • 0.974V ROFB2 Note that ROFB1 and ROFB2 are the same resistors that program the output voltage regulation level. Therefore, the output voltage regulation level is always 122.5% of the instant-on voltage level. where ICLIM is the full scale charge current limit. VOUT(INST _ ON) = For example, when charging a 3-cell Lithium Ion battery with a programmed full charged current of 1A, the float voltage is 12.6V, the bad battery voltage level is 8.55V and the instant-on voltage level is 10.8V. During instant-on operation and in the trickle charge mode, the worst case maximum power dissipation in the PMOS is 1.08W. When the battery voltage is above the bad battery voltage level, then the worst case maximum power dissipation is 2.25W. During instant-on operation, it is critical to consider the charging PMOS power dissipation. When the battery voltage is below the low battery threshold (VLOBAT), the power dissipation in the PMOS can be calculated as follows: When overheating of the charging PMOS is a concern, it is recommended that the user add a temperature detection circuit that pulls down on the NTC pin. This pauses charging whenever the external PMOS temperature is too high. A sample circuit that performs this temperature detection function is shown in Figure 7. PTRKL = [0.86 • VFLOAT – VBAT ] • ICLIM(TRKL) where ICLIM(TRKL) is the trickle charge current limit. TO SYSTEM CSP RCS LTC4000 VISHAY CURVE 2 NTC RESISTOR THERMALLY COUPLED WITH CHARGING PMOS RNTC2 CSN BGATE M2 R4 = RNTC2 AT 25°C BAT BIAS R3 CBIAS 162k 2N7002L NTC Li-Ion BATTERY PACK RNTC1 LTC1540 – + RISING TEMPERATURE THRESHOLD SET AT 90°C 20k VOLTAGE HYSTERESIS CAN BE PROGRAMMED FOR TEMPERATURE HYSTERESIS 86mV ≈ 10°C 4000 F07 Figure 7. Charging PMOS Overtemperature Detection Circuit Protecting PMOS from Overheating 4000f 20 LTC4000 Applications Information Similar to the input external PMOS, the charging external PMOS must be able to withstand a gate to source voltage greater than VBGATE(ON) (15V maximum) or the maximum regulated voltage at the CSP pin, whichever is less. Consider the expected maximum current, power dissipation and instant-on voltage drop when selecting this PMOS. The PMOS suggestions in Table 1 are an appropriate starting point depending on the application. Float Voltage, Output Voltage and Instant-On Voltage Dependencies The formulas for setting the float voltage, output voltage and instant-on voltage are repeated here: RBFB1 + RBFB2 • 1.136V RBFB2 +R R = OFB1 OFB2 • 1.193V ROFB2 VFLOAT = VOUT VOUT(INST _ ON) = ROFB1 + ROFB2 • 0.974V ROFB2 In the typical application, VOUT is set higher than VFLOAT to ensure that the battery is charged fully to its intended float voltage. On the other hand, VOUT should not be programmed too high since VOUT(INST_ON), the minimum voltage on CSP, depends on the same resistors ROFB1 and ROFB2 that set VOUT. As noted before, this means that the output voltage regulation level is always 122.5% of the instant-on voltage. The higher the programmed value of VOUT(INST_ON), the larger the operating region when the charger PMOS is driven in the linear region where it is less efficient. If ROFB1 and ROFB2 are set to be equal to RBFB1 and RBFB2 respectively, then the output voltage is set at 105% of the float voltage and the instant-on voltage is set at 86% of the float voltage. Figure 8 shows the range of possible output voltages that can be set for VOUT(INST_ON) and VOUT with respect to VFLOAT to ensure the battery can be fully charged in an ideal scenario. Taking into account possible mismatches between the resistor dividers as well as mismatches in the various regulation loops, VOUT should not be programmed to be less than 105% of VFLOAT to ensure that the battery can be fully charged. This automatically means that the instant-on voltage level should not be programmed to be less than 86% of VFLOAT. POSSIBLE OUTPUT VOLTAGE RANGE 105% NOMINAL OUTPUT VOLTAGE NOMINAL FLOAT VOLTAGE POSSIBLE INSTANT-ON VOLTAGE RANGE 100% MINIMUM PRACTICAL OUTPUT VOLTAGE 100% 100% 86% NOMINAL INSTANT-ON VOLTAGE 75% MINIMUM PRACTICAL INSTANT-ON VOLTAGE 81.6% 4000 F08 Figure 8. Possible Voltage Ranges for VOUT and VOUT(INST_ON) in Ideal Scenario 4000f 21 LTC4000 Applications Information Battery Temperature Qualified Charging To use the battery temperature qualified charging feature, connect an NTC thermistor, RNTC, between the NTC pin and the GND pin, and a bias resistor, R3, from the BIAS pin to the NTC pin (Figure 9). Thermistor manufacturer datasheets usually include either a temperature lookup table or a formula relating temperature to the resistor value at that corresponding temperature. BIAS CBIAS R3 LTC4000 NTC BAT NTC RESISTOR THERMALLY COUPLED WITH BATTERY PACK RNTC 4000 F09 Figure 9. NTC Thermistor Connection In a simple application, R3 is a 1% resistor with a value equal to the value of the chosen NTC thermistor at 25°C (R25). In this simple setup, the LTC4000 will pause charging when the resistance of the NTC thermistor drops to 0.54 times the value of R25. For a Vishay Curve 2 thermistor, this corresponds to approximately 41.5°C. As the temperature drops, the resistance of the NTC thermistor rises. The LTC4000 is also designed to pause charging when the value of the NTC thermistor increases to three times the value of R25. For a Vishay Curve 2 thermistor, this corresponds to approximately –1.5°C. With Vishay Curve 2 thermistor, the hot and cold comparators each have approximately 5°C of hysteresis to prevent oscillation about the trip point. The hot and cold threshold can be adjusted by changing the value of R3. Instead of simply setting R3 to be equal to R25, R3 is set according to one of the following formulas: R3 = Notice that with only one degree of freedom (i.e. adjusting the value of R3), the user can only use one of the formulas above to set either the cold or hot threshold but not both. If the value of R3 is set to adjust the cold threshold, the value of the NTC resistor at the hot threshold is then equal to 0.179 • RNTC at cold_threshold. Similarly, if the value of R3 is set to adjust the hot threshold, the value of the NTC resistor at the cold threshold is then equal to 5.571 • RNTC at cold_threshold. Note that changing the value of R3 to be larger than R25 will move both the hot and cold threshold lower and vice versa. For example, using a Vishay Curve 2 thermistor whose nominal value at 25°C is 100k, the user can set the cold temperature to be at 5°C by setting the value of R3 = 75k, which automatically then sets the hot threshold at approximately 50°C. It is possible to adjust the hot and cold threshold independently by introducing another resistor as a second degree of freedom (Figure 10). The resistor RD in effect reduces the sensitivity of the resistance between the NTC pin and ground. Therefore, intuitively this resistor will move the hot threshold to a hotter temperature and the cold threshold to a colder temperature. BIAS R3 LTC4000 CBIAS NTC RD BAT NTC RESISTOR THERMALLY COUPLED WITH BATTERY PACK RNTC 4000 F10 Figure 10. NTC Thermistor Connection with Desensitizing Resistor RD RNTC at cold_ threshold 3 or R3 = 1.857 • RNTC at hot _ threshold 4000f 22 LTC4000 Applications Information The value of R3 and RD can now be set according to the following formula: R at cold_ threshold – RNTC at hot _ threshold R3 = NTC 2.461 RD = 0.219 • RNTC at cold_ threshold – 1.219 • RNTC at hot _ threshold Note the important caveat that this method can only be used to desensitize the thermal effect on the thermistor and hence push the hot and cold temperature thresholds apart from each other. When using the formulas above, if the user finds that a negative value is needed for RD, the two temperature thresholds selected are too close to each other and a higher sensitivity thermistor is needed. For example, this method can be used to set the hot and cold thresholds independently to 60°C and –5°C. Using a Vishay Curve 2 thermistor whose nominal value at 25°C is 100k, the formula results in R3 = 130k and RD = 41.2k for the closest 1% resistors values. To increase thermal sensitivity such that the valid charging temperature band is much smaller than 40°C, it is possible to put a PTC (positive thermal coefficient) resistor in series with R3 between the BIAS pin and the NTC pin. This PTC resistor also needs to be thermally coupled with the battery. Note that this method increases the number of thermal sensing connections to the battery pack from one wire to three wires. The exact value of the nominal PTC resistor required can be calculated using a similar method as described above, keeping in mind that the threshold at the NTC pin is always 75% and 35% of VBIAS. Leaving the NTC pin floating or connecting it to a capacitor disables all NTC functionality. The FLT and CHRG Indicator Pins The FLT and CHRG pins in the LTC4000 provide status indicators. Table 2 summarizes the mapping of the pin states to the part status. Table 2. FLT and CHRG Status Indicator FLT CHRG 0 0 NTC Over Ranged – Charging Paused STATUS 1 0 Charging Normally 0 1 Charging Terminated and Bad Battery Detected 1 1 VIBMON < (VC/X – 10mV) where 1 indicates a high impedance state and 0 indicates a low impedance pull-down state. Note that VIBMON < (VCX – 10mV) corresponds to charge termination only if the C/X termination is selected. If the charger timer termination is selected, constant voltage charging may continue for the remaining charger timer period even after the indicator pins indicate that VIBMON < (VCX – 10mV). This is also true when no termination is selected, constant voltage charging will continue even after the indicator pins indicate that VIBMON < (VCX – 10mV). The BIAS Pin For ease of use the LTC4000 provides a low dropout voltage regulator output on the BIAS pin. Designed to provide up to 0.5mA of current at 2.9V, this pin requires at least 470nF of low ESR bypass capacitance for stability. Use the BIAS pin as the pull-up source for the NTC resistor networks, since the internal reference for the NTC circuitry is based on a ratio of the voltage on the BIAS pin. Furthermore, various 100k pull-up resistors can be conveniently connected to the BIAS pin. 4000f 23 LTC4000 Applications Information Setting the Input Voltage Monitoring Resistor Divider The falling threshold voltage level for this monitoring function can be calculated as follows: ⎛V ⎞ RVM1 = ⎜ VM _ RST – 1⎟ • R VM2 ⎝ 1.193V ⎠ where RVM1 and RVM2 form a resistor divider connected between the monitored voltage and GND, with the center tap point connected to the VM pin as shown in Figure 6. The rising threshold voltage level can be calculated similarly. Compensation In order for the LTC4000 to control the external DC/DC converter, it has to be able to overcome the sourcing bias current of the ITH or VC pin of the DC/DC converter. The typical sinking capability of the LTC4000 at the ITH pin is 1mA at 0.4V with a maximum voltage range of 0V to 6V. It is imperative that the local feedback of the DC/DC converter be set up such that during regulation of any of the LTC4000 loops this local loop is out of regulation and sources as much current as possible from its ITH/VC pin. For example for a DC/DC converter regulating its output voltage, it is recommended that the converter feedback divider is programmed to be greater than 110% of the output voltage regulation level programmed at the OFB pin. There are four feedback loops to consider when setting up the compensation for the LTC4000. As mentioned before these loops are: the input current loop, the charge current loop, the float voltage loop and the output voltage loop. All of these loops have an error amp (A4-A7) followed by another amplifier (A10) with the intermediate node driving the CC pin and the output of A10 driving the ITH pin as shown in Figure 11. The most common compensation network of a series capacitor (CC) and resistor (RC) between the CC pin and the ITH pin is shown here. Each of the loops has slightly different dynamics due to differences in the feedback signal path. The analytic description of each of the loops is included in the Appendix section. In most situations, an alternative empirical approach to compensation, as described here, is more practical. A4-A7 gm4-7 = 0.2m + – LTC4000 RO4-7 CC A10 gm10 = 0.1m – + CC RC ITH RO10 4000 F11 Figure 11. Error Amplifier Followed by Output Amplifier Driving CC and ITH Pins Empirical Loop Compensation Based on the five analytical expressions given in the Appendix section, and the transfer function from the ITH pin to the input and output current of the external DC/DC converter, the user can analytically determine the complete loop transfer function of each of the loops. Once these are obtained, it is a matter of analyzing the gain and phase bode plots to ensure that there is enough phase and gain margin at unity crossover with the selected values of RC and CC for all operating conditions. Even though it is clear that an analytical compensation method is possible, sometimes certain complications render this method difficult to tackle. These complications include the lack of easy availability of the switching converter transfer function from the ITH or VC control node to its input or output current, and the variability of parameter values of the components such as the ESR of the output capacitor or the RDS(ON) of the external PFETs. Therefore a simpler and more practical way to compensate the LTC4000 is provided here. This empirical method involves injecting an AC signal into the loop, observing the loop transient response and adjusting the CC and RC values to quickly iterate towards the final values. Much of the detail of this method is derived from Application Note 19 which can be found at www.linear.com using AN19 in the search box. Figure 12 shows the recommended setup to inject an AC-coupled output load variation into the loop. A function generator with 50Ω output impedance is coupled through a 50Ω/1000µF series RC network to the regulator output. 4000f 24 LTC4000 Applications Information SWITCHING CONVERTER GND ITH 1k 0.015µF RC CC CLN ITH CC IOUT CSP LTC4000 IN A 10k B 1500pF 50Ω 1W 1000µF (OBSERVE POLARITY) SCOPE GROUND CLIP CSN GND BAT BGATE 50Ω GENERATOR f = 50Hz VIN 4000 F12 Figure 12. Empirical Loop Compensation Setup Generator frequency is set at 50Hz. Lower frequencies may cause a blinking scope display and higher frequencies may not allow sufficient settling time for the output transient. Amplitude of the generator output is typically set at 5VP-P to generate a 100mAP-P load variation. For lightly loaded outputs (IOUT < 100mA), this level may be too high for small signal response. If the positive and negative transition settling waveforms are significantly different, amplitude should be reduced. Actual amplitude is not particularly important because it is the shape of the resulting regulator output waveform which indicates loop stability. A 2-pole oscilloscope filter with f = 10kHz is used to block switching frequencies. Regulators without added LC output filters have switching frequency signals at their outputs which may be much higher amplitude than the low frequency settling waveform to be studied. The filter frequency is high enough for most applications to pass the settling waveform with no distortion. Oscilloscope and generator connections should be made exactly as shown in Figure 12 to prevent ground loop errors. The oscilloscope is synced by connecting the channel B probe to the generator output, with the ground clip of the second probe connected to exactly the same place as channel A ground. The standard 50Ω BNC sync output of the generator should not be used because of ground loop errors. It may also be necessary to isolate either the generator or oscilloscope from its third wire (earth ground) connection in the power plug to prevent ground loop errors in the scope display. These ground loop errors are checked by connecting channel A probe tip to exactly the same point as the probe ground clip. Any reading on channel A indicates a ground loop problem. Once the proper setup is made, finding the optimum values for the frequency compensation network is fairly straightforward. Initially, CC is made large (≥1μF) and RC is made small (≈10k). This nearly always ensures that the regulator will be stable enough to start iteration. Now, if the regulator output waveform is single-pole over damped (see the waveforms in Figure 13), the value of CC is reduced in steps of about 2:1 until the response becomes slightly under damped. Next, RC is increased in steps of 2:1 to introduce a loop zero. This will normally improve damping and allow the value of CC to be further reduced. Shifting back and forth between RC and CC variations will allow one to quickly find optimum values. 4000f 25 LTC4000 Applications Information GENERATOR OUTPUT REGULATOR OUTPUT WITH LARGE CC, SMALL RC WITH REDUCED CC, SMALL RC EFFECT OF INCREASED RC FURTHER REDUCTION IN CC MAY BE POSSIBLE IMPROPER VALUES WILL CAUSE OSCILLATIONS 4000 F13 Figure 13. Typical Output Transient Response at Various Stability Level If the regulator response is under damped with the initial large value of CC, RC should be increased immediately before larger values of CC are tried. This will normally bring about the over damped starting condition for further iteration. The optimum values for RC and CC normally means the smallest value for CC and the largest value for RC which still guarantee well damped response, and which result in the largest loop bandwidth and hence loop settling that is as rapid as possible. The reason for this approach is that it minimizes the variations in output voltage caused by input ripple voltage and output load transients. A switching regulator which is grossly over damped will never oscillate, but it may have unacceptably large output transients following sudden changes in input voltage or output loading. It may also suffer from excessive overshoot problems on startup or short circuit recovery. To guarantee acceptable loop stability under all conditions, the initial values chosen for RC and CC should be checked under all conditions of input voltage and load current. The simplest way of accomplishing this is to apply load currents of minimum, maximum and several points in between. At each load current, input voltage is varied from minimum to maximum while observing the settling waveform. If large temperature variations are expected for the system, stability checks should also be done at the temperature extremes. There can be significant temperature variations in several key component parameters which affect stability; in particular, input and output capacitor value and their ESR, and inductor permeability. The external converter parametric variations also need some consideration especially the transfer function from the ITH/VC pin voltage to the output variable (voltage or current). The LTC4000 parameters that vary with temperature include the transconductance and the output resistance of the error amplifiers (A4-A7). For modest temperature variations, conservative over damping under worst-case room temperature conditions is usually sufficient to guarantee adequate stability at all temperatures. One measure of stability margin is to vary the selected values of both RC and CC by 2:1 in all four possible combinations. If the regulator response remains reasonably well damped under all conditions, the regulator can be considered fairly tolerant of parametric variations. Any tendency towards an under damped (ringing) response indicates that a more conservative compensation may be needed. 4000f 26 LTC4000 Applications Information Design Example In this design example, the LTC4000 is paired with the LT3845 buck converter to create a 10A, 3-cell LiFePO4 battery charger. The circuit is shown on the front page and is repeated here in Figure 14. • RCL is set at 24.9kΩ such that the voltage at the CL pin is 1.25V. Similar to the IIMON pin, the regulation voltage on the IBMON pin is clamped at 1V with an accurate internal reference. Therefore, the charge current limit is set at 10A according to the following formula: • The input voltage monitor falling threshold is set at 14.3V according to the following formula: 0.050V 0.050V = = 10A RCS 5mΩ • The trickle charge current level is consequently set at 1.25A, according to the following formula: ⎛ 14.3V ⎞ RVM1 = ⎜ − 1⎟ • 100kΩ ≈ 1.10MΩ ⎝ 1.193V ⎠ • The IL pin is left open such that the voltage on this pin is >1.05V. The regulation voltage on the IIMON pin is clamped at 1.0V with an accurate internal reference. Therefore, the input current limit is set at 10A according to the following formula: R IS = ICLIM(MAX) = 0.050V = 5mΩ 10A ICLIM(TRKL) = 0.25µA • 24.9kΩ = 1.25A 5mΩ • The battery float voltage is set at 10.8V according to the following formula: ⎞ ⎛ 10.8 RBFB1 = ⎜ − 1⎟ • 133kΩ ≈ 1.13MΩ ⎝ 1.136 ⎠ • The bad battery detection time is set at 43 minutes according to the following formula: CTMR (nF) = tBADBAT (h) • 138.5 = 15V TO 60V 5mΩ IN LT3845 SHDN ITH CC IID IGATE CSP BAT 127k LTC4000 FBG 133k BFB IIMON 10nF 1.13M NTC IBMON 10nF Si7135DP CSN OFB ENC CHRG FLT 3.0V 5mΩ BGATE VM 100k 1.15M 47nF 1µF 1.10M 12V, 15A 100µF 14.7k RST CLN IN Si7135DP OUT VC 43 • 138.5 = 100nF 60 TMR IL 0.1µF CL 22.1k 10k GND BIAS CX 22.1k 10k 10.8V FLOAT 10A MAX CHARGE CURRENT 3-CELL Li-Ion BATTERY PACK 1µF NTHS0603 N02N1002J 4000 F14 Figure 14. 48V to 10.8V at 10A Buck Converter Charger for Three LiFePO4 Cells 4000f 27 LTC4000 Applications Information • The charge termination time is set at 2.9 hours according to the following formula: CTMR (nF) = t TERMINATE (h) • 34.6 = 2.9 • 34.6 = 100nF • The C/X current termination level is programmed at 1A according to the following formula: RCX = (1A • 5mΩ) + 0.5mV ≈ 22.1kΩ 0.25µA Note that in this particular solution, the timer termination is selected since a capacitor connects to the TMR pin. Therefore, this C/X current termination level only applies to the CHRG indicator pin. • The output voltage regulation level is set at 12V according to the following formula: ⎞ ⎛ 12 ROFB1 = ⎜ − 1⎟ • 127kΩ ≈ 1.15MΩ ⎝ 1.193 ⎠ • The instant-on voltage level is consequently set at 9.79V according to the following formula: VINST _ ON = • The range of valid temperature for charging is set at –1.5°C to 41.5°C by picking a 10k Vishay Curve 2 NTC thermistor that is thermally coupled to the battery, and connecting this in series with a regular 10k resistor to the BIAS pin. • For compensation, the procedure described in the empirical loop compensation section is followed. As recommended, first a 1µF CC and 10k RC is used, which sets all the loops to be stable. For an example of typical transient responses, the charge current regulation loop when VOFB is regulated to VOUT(INST_ON) is used here. Figure 15 shows the recommended setup to inject a DC-coupled charge current variation into this particular loop. The input to the CL pin is a square wave at 70Hz with the low level set at 120mV and the high level set at 130mV, corresponding to a 1.2A and 1.3A charge current (100mA charge current step). Therefore, in this particular example the trickle charge current regulation stability is examined. Note that the nominal trickle charge current in this example is programmed at 1.25A (RCL = 24.9kΩ). 1150kΩ + 127kΩ • 0.974V = 9.79V 127kΩ The worst-case power dissipation during instant-on operation can be calculated as follows: • During trickle charging: B A 10k 1500pF 1k LTC4000 PTRKL = [0.86 • VFLOAT – VBAT ] • ICLIM _ TRKL = [0.86 • 10.8] • 1A = 9.3W IBMON 0.015µF CL SQUARE WAVE GENERATOR f = 60Hz 4000 F15 • And beyond trickle charging: PINST _ ON = [0.86 • VFLOAT – VBAT ] • ICLIM = [0.86 • 10.8 – 7.33] • 10A = 19.3W Figure 15. Charge Current Regulation Loop Compensation Setup Therefore, depending on the layout and heat sink available to the charging PMOS, the suggested PMOS over temperature detection circuit included in Figure 7 may need to be included. For the complete application circuit, please refer to Figure 25. 4000f 28 LTC4000 Applications Information With CC = 1µF, RC = 10k at VIN = 20V, VBAT = 7V, VCSP regulated at 9.8V and a 0.2A output load condition at CSP, the transient response for a 100mA charge current step observed at IBMON is shown in Figure 16. 10 15 5 10 0 5 VIBMON (mV) 5mV/DIV VIBMON (mV) 5mV/DIV 15 The transient response now indicates an overall under damped system. As noted in the empirical loop compensation section, the value of RC is now increased iteratively until RC = 20k. The transient response of the same loop with CC = 22nF and RC = 20k is shown in Figure 18. –5 –10 –15 –20 –15 –10 5 0 5ms/DIV –5 10 15 20 –15 –20 –15 –10 Figure 16. Transient Response of Charge Current Regulation Loop Observed at IBMON When VOFB is Regulated to VOUT(INST_ON) with CC = 1µF, RC = 10k for a 100mA Charge Current Step The transient response shows a small overshoot with slow settling indicating a fast minor loop within a well damped overall loop. Therefore, the value of CC is reduced iteratively until CC = 22nF. The transient response of the same loop with CC = 22nF and RC = 10k is shown in Figure 17. 15 VIBMON (mV) 5mV/DIV 10 5 0 –5 –10 –5 5 0 5ms/DIV 10 15 20 –5 –10 25 4000 F16 –15 –20 –15 –10 0 25 4000 F17 Figure 17. Transient Response of Charge Current Regulation Loop Observed at IBMON When VOFB is Regulated to VOUT(INST_ON) with CC = 22nF, RC = 10k for a 100mA Charge Current Step –5 5 0 5ms/DIV 10 15 20 25 4000 F18 Figure 18. Transient Response of Charge Current Regulation Loop Observed at IBMON When VOFB is Regulated to VOUT(INST_ON) with CC = 22nF, RC = 20k for a 100mA Charge Current Step Note that the transient response is close to optimum with some overshoot and fast settling. If after iteratively increasing the value of RC, the transient response again indicates an over damped system, the step of reducing CC can be repeated. These steps of reducing CC followed by increasing RC can be repeated continuously until one arrives at a stable loop with the smallest value of CC and the largest value of RC. In this particular example, these values are found to be CC = 22nF and RC = 20kΩ. After arriving at these final values of RC and CC, the stability margin is checked by varying the values of both RC and CC by 2:1 in all four possible combinations. After which the setup condition is varied, including varying the input voltage level and the output load level and the transient response is checked at these different setup conditions. Once the desired responses on all different conditions are obtained, the values of RC and CC are noted. 4000f 29 LTC4000 Applications Information This same procedure is then repeated for the other four loops: the input current regulation, the output voltage regulation, the battery float voltage regulation and finally the charge current regulation when VOFB > VOUT(INST_ON). Note that the resulting optimum values for each of the loops may differ slightly. The final values of CC and RC are then selected by combining the results and ensuring the most conservative response for all the loops. This usually entails picking the largest value of CC and the smallest value of RC based on the results obtained for all the loops. In this particular example, the value of CC is finally set to 47nF and RC = 14.7kΩ. Board Layout Considerations In the majority of applications, the most important parameter of the system is the battery float voltage. Therefore, the user needs to be extra careful when placing and routing the feedback resistor RBFB1 and RBFB2. In particular, the battery sense line connected to RBFB1 and the ground return line for the LTC4000 must be Kelvined back to where the battery output and the battery ground are located respectively. Figure 19 shows this Kelvin sense configuration. For accurate current sensing, the sense lines from RIS and RCS (Figure 19) must be Kelvined back all the way to the sense resistors terminals. The two sense lines of each resistor must also be routed close together and away from noise sources to minimize error. Furthermore, current filtering capacitors should be placed strategically to ensure that very little AC current is flowing through these sense resistors as mentioned in the applications section. The decoupling capacitors CIN and CBIAS must be placed as close to the LTC4000 as possible. This allows as short a route as possible from CIN to the IN and GND pins, as well as from CBIAS to the BIAS and GND pins. In a typical application, the LTC4000 is paired with an external DC/DC converter. The operation of this converter often involves high dV/dt switching voltage as well as high currents. Isolate these switching voltages and currents from the LTC4000 section of the board as much as possible by using good board layout practices. These include separating noisy power and signal grounds, having a good low impedance ground plane, shielding whenever necessary, and routing sensitive signals as short as possible and away from noisy sections of the board. SWITCHING CONVERTER GND ITH SYSTEM LOAD RC CC ITH CC CLN RIS IID IGATE CSP RCS LTC4000 IN CSN BGATE BAT RBFB1 BFB VIN RBFB2 GND FBG 4000 F19 Figure 19. Kelvin Sense Lines Configuration for LTC4000 4000f 30 LTC4000 Applications Information Appendix—The Loop Transfer Functions The Input Current Regulation Loop When a series resistor (RC) and capacitor (CC) is used as the compensation network as shown in Figure 11, the transfer function from the input of A4-A7 to the ITH pin is simply as follows: The feedback signal for the input current regulation loop is the sense voltage across the input current sense resistor (RIS). where gm4-7 is the transconductance of error amplifier A4A7, typically 0.5mA/V; gm10 is the output amplifier (A10) transconductance, RO4-7 is the output impedance of the error amplifier, typically 50mΩ; and RO10 is the effective output impedance of the output amplifier, typically 10mΩ with the ITH pin open circuit. Note this simplification is valid when gm10 • RO10 • RO4-7 • CC = AV10 • RO4-7 • CC is much larger than any other poles or zeroes in the system. Typically AV10 • RO4-7 = 5 • 1010 with the ITH pin open circuit. The exact value of gm10 and RO10 depends on the pull-up current and impedance connected to the ITH pin respectively. This voltage is amplified by a factor of 20 and compared to the voltage on the IL pin by the transconductance error amplifier (A4). This amplifier then drives the output transconductance amplifier (A10) to appropriately adjust the voltage on the ITH pin driving the external DC/DC converter to regulate the input current across the sense resistor (RIS). This loop is shown in detail in Figure 20. The simplified loop transmission is: ⎤ ⎡⎛ 1 ⎞ ⎢ ⎜RC – ⎟ CCs + 1⎥ gm10 ⎠ ⎝ ⎥• LIC (s) = gm4 ⎢ ⎥ ⎢ CCs ⎥ ⎢ ⎦ ⎣ ⎤ ⎡ 20R (R2 IS CIIMON s + 1) ⎥ • Gmip (s) ⎢ ⎢⎣ (R1+ R2) CIIMONs + 1 ⎥⎦ where Gmip(s) is the transfer function from VITH to the input current of the external DC/DC converter. In most applications, compensation of the loops involves picking the right values of RC and CC. Aside from picking the values of RC and CC, the value of gm10 may also be adjusted. The value of gm10 can be adjusted higher by increasing the pull-up current into the ITH pin and its value can be approximated as: gm10 I + 5µA = ITH 50mV The higher the value of gm10, the smaller the lower limit of the value of RC would be. This lower limit is to prevent the presence of the right half plane zero. Even though all the loops share this transfer function from the error amplifier input to the ITH pin, each of the loops has a slightly different dynamic due to differences in the feedback signal path. RIS IN IIN CIN IIMON R2 20k IN CLN + – ⎤ ⎡⎛ 1 ⎞ s + 1 C ⎥ ⎢ ⎜RC – ⎟ C gm10 ⎠ VITH ⎝ ⎥ ⎢ (s) = gm4-7 ⎥ ⎢ RO4-7 • CCs VFB ⎥ ⎢ ⎦ ⎣ A8 gm8 = 0.33m BIAS CIIMON R1 60k LTC4000 A4 gm4 = 0.5m 50µA 1V IL + – – RO4 CC A10 gm10 = 0.1m – + CC RC ITH RO10 RIL 4000 F20 Figure 20. Simplified Linear Model of the Input Current Regulation Loop 4000f 31 LTC4000 Applications Information The Output Voltage Regulation Loop The Battery Float Voltage Regulation Loop The feedback signal for the output voltage regulation loop is the voltage on the OFB pin, which is connected to the center node of the resistor divider between the output voltage (connected to CSP) and the FBG pin. This voltage is compared to an internal reference (1.193V typical) by the transconductance error amplifier A7. This amplifier then drives the output transconductance amplifier (A10) to appropriately adjust the voltage on the ITH pin driving the external DC/DC converter to regulate the output voltage observed by the OFB pin. This loop is shown in detail in Figure 21. The battery float voltage regulation loop is very similar to the output float voltage regulation loop. Instead of observing the voltage at the OFB pin, the battery float voltage regulation loop observes the voltage at the BFB pin. LTC4000 INPUT CC A10 gm10 = 0.1m – + ITH RO10 A7 gm7 = 0.5m RO7 CC RC + – + – Gmop(s) LOAD CSP ROFB1 OFB 1.193V CL RL One significant difference is that while the value of RL in the output voltage loop can vary significantly, the output resistance of the battery float voltage loop is a small constant value approximately equal to the sum of the on-resistance of the external PFET (RDS(ON)) and the series internal resistance of the battery (RBAT). This approximation is valid for any efficient system such that most of the output power from the battery is delivered to the system load and not dissipated on the battery internal resistance or the charging PFET on-resistance. For a typical system, minimum RL is at least five times larger than RDS(ON) + RBAT and RBFB is at least 106 times larger than RBAT. Figure 22 shows the detail of the battery float voltage regulation loop. LTC4000 ROFB2 FBG – + INTERNALLY PULLED HIGH 4000 F21 ⎡⎛ ⎤ 1 ⎞ ⎢ ⎜R C – ⎟ CCs + 1⎥ gm10 ⎠ ⎝ ⎥• L OV (s) = gm7 ⎢ ⎢ ⎥ CCs ⎢ ⎥ ⎣ ⎦ RO6 CC RC ITH RO10 A7 gm6 = 0.5m Figure 21. Simplified Linear Model of the Output Voltage Regulation Loop The simplified loop transmission is as follows: INPUT CC A10 gm10 = 0.1m + – + – Gmop(s) LOAD BAT RBFB1 BFB RCS CL RL RDS(ON) 1.136V RBFB2 FBG RBAT INTERNALLY PULLED HIGH 4000 F22 Figure 22. Simplified Linear Model of the Battery Float Voltage Regulation Loop ⎡R ⎤ ⎡ ⎤ RL OFB2 • ⎢ ⎥ ⎢ ⎥ • Gmo p (s) ⎣ R OFB ⎦ ⎣ RL • CL s + 1⎦ where Gmop(s) is the transfer function from VITH to the output current of the external DC/DC converter, and ROFB = ROFB1 + ROFB2. 4000f 32 LTC4000 Applications Information In Figure 22 the battery is approximated to be a signal ground in series with the internal battery resistance RBAT. Therefore, the simplified loop transmission is as follows: ⎤ ⎡⎛ 1 ⎞ ⎢ ⎜RC – ⎟ CCs + 1⎥ gm10 ⎠ ⎝ ⎥• LBV (s) = gm6 ⎢ ⎥ ⎢ CCs ⎥ ⎢ ⎦ ⎣ ⎡RBFB2 ⎤ ⎡ ⎤ RLB ⎢ ⎥•⎢ ⎥ • Gmop (s) ⎣ RBFB ⎦ ⎣RLB • CL s + 1⎦ where Gmop(s) is the transfer function from VITH to the output current of the external DC/DC converter, RBFB = RBFB1 + RBFB2, and RLB = RL//(RDS(ON) + RCS + RBAT) represents the effective output resistance from the LOAD node to GND. The Battery Charge Current Regulation Loop The simplified loop transmission is: ⎤ ⎡⎛ 1 ⎞ ⎢ ⎜RC – ⎟ CCs + 1⎥ gm10 ⎠ ⎝ ⎥• LCC (s) = gm5 ⎢ ⎥ ⎢ CCs ⎥ ⎢ ⎦ ⎣ ⎡ (R2 • CIBMONs + 1) ⎤ RL 20RCS • ⎢ • ⎥• ⎢⎣ (R1+ R2) CIBMONs + 1⎥⎦ Rf + RL ⎤ ⎡ 1 ⎥ • Gmop (s) ⎢ ⎢⎣ (RL Rf ) CL s + 1⎥⎦ where Gmop(s) is the transfer function from VITH to the output current of the external DC/DC converter, Rf = RCS + RDS(ON) + RBAT, and RL//Rf represents the effective resistance value resulting from the parallel combination of RL and Rf. CC RC RO10 CC ITH LTC4000 INPUT A10 gm10 = 0.1m + – RO5 A5 gm5 = 0.5m + – – Due to the presence of the instant-on feature, description of the charge current regulation loop has to be divided into two separate operating regions. These regions of operation depend on whether the voltage on the OFB pin is higher or lower than the instant-on threshold (VOUT(INST_ON)). In this operating region, the external charging PFET’s gate is driven low and clamped at VBGATE(ON). The detail of this loop is shown in Figure 23. – + This final regulation loop combines certain dynamic characteristics that are found in all the other three loops. The feedback signal for this charge current regulation loop is the sense voltage across the charge current sense resistor (RCS). This voltage is amplified by a factor of 20 and compared to the voltage on the CL pin by the transconductance error amplifier (A5). In a familiar fashion, this amplifier drives the output transconductance amplifier (A10) to appropriately adjust the voltage on the ITH pin driving the external DC/DC converter to regulate the input current across the sense resistor (RCS). The Battery Charge Current Regulation Loop when VOFB > VOUT(INST_ON) BIAS A8 gm8 = 0.33m 1V 50µA/ 5µA R1 60k R2 20k + – Gmop(s) RL CL CSP RCS CSN RDS(ON) CL RCL IBMON CIBMON BAT 4000 F23 RBAT Figure 23. Simplified Linear Model of the Charge Current Regulation Loop with the External Charging PFET Driven On 4000f 33 LTC4000 Applications Information The Battery Charge Current Regulation Loop when VOFB is Regulated to VOUT(INST_ON) The simplified loop transmission is: When the battery voltage is below the instant-on level, the external charging PFET is driven linearly to regulate the voltage at the output (connected to the CSP pin). The output voltage is regulated such that the voltage at the OFB pin is equal to the instant-on threshold (VOUT(INST_ON)). If this external PFET regulation is fast compared to the unity crossover frequency of the battery charge current regulation loop, then the voltage at the output can be considered a small signal ground. However, in the LTC4000 the external PFET regulation is purposely made slow to allow for a broader selection of possible PFETs to be used. Therefore, the linear model of the PFET has to be included in the analysis of the charge current regulation loop. The detail of this loop is shown in Figure 24. CC RC RO10 CC ITH LTC4000 – + + – RO5 A5 gm5 = 0.5m + – – BIAS A8 gm8 = 0.33m 1V 50µA/ 5µA R1 60k R2 20k + – CL RCL IBMON CIBMON ⎡ ⎤ 1 •⎢ ⎥• R fIDC + RL ⎢⎣ (RL R fIDC ) CL s + 1⎥⎦ RL ⎡ ⎤ Cg ⎢ ⎥ s+1 gmEXT ⎢ ⎥ • Gmo p (s) ⎢⎛R + R ⎥ ⎞ Cg BAT CS ⎢⎜ s + 1⎥ ⎟ ⎢⎣ ⎝ R fIDC ⎠ gmEXT ⎥⎦ RL RCS CSN Cg CL Gmop(s) CSP ⎡ (R2 • C ⎤ IBMONs + 1) 20R CS • ⎢ ⎥• ⎢⎣ (R1+ R2 ) CIBMONs + 1⎥⎦ where Gmop(s) is the transfer function from VITH to the output current of the external DC/DC converter, gmEXT is the small signal transconductance of the output PFET, RflDC = RCS + 1/gmEXT + RBAT and RL//RflDC represents the effective resistance value resulting from the parallel combination of RL and RflDC. INPUT A10 gm10 = 0.1m ⎡⎛ ⎤ 1 ⎞ ⎢ ⎜R C – ⎟ CCs + 1⎥ gm10 ⎠ ⎝ ⎥• L CC2 (s) = gm5 ⎢ ⎢ ⎥ CCs ⎢ ⎥ ⎣ ⎦ 1 gmEXT BAT 4000 F24 RBAT Figure 24. Simplified Linear Model of the Charge Current Regulation Loop with the External Charging PFET Linearly Regulated 4000f 34 LTC4000 Typical Applications VIN 15V TO 60V 10A MAX 5mΩ 2.2µF BSC123NO8NS3 47µF VIN TG WÜRTH ELEKTRONIC 74435561100 10µH SW BG CSS B160 1.5nF Si7135DP 3mΩ BSC123NO8NS3 0.1µF BURST_EN SYNC VOUT 12V, 15A 33µF ×3 BOOST BAS521 SGND 1.15M VCC 1µF LT3845A 1N4148 182k VFB fSET 49.9k 16.2k SENSE+ 5mΩ – SHDN VC SENSE 14.7k RST ITH NTHS0603 N02N1002J 47nF CC IID IGATE CSP CSN BGATE CLN IN 1.10M 10nF 1µF BAT OFB VM 100k BZX84C3VO LTC4000 ENC CHRG FLT 127k FBG 133k IIMON 10nF IBMON 10nF Si7135DP IL CL CX TMR 24.9k 0.1µF BFB NTC GND BIAS 22.1k 1µF 162k 10k 10k IN+ 1.13M RNTC 2N7002L V+ OUT NTHS0603 N02N1002J IN– 20k LTC1540 HYST 3-CELL LiFePO4 BATTERY PACK 38.3k REF V– GND 1M 4000 F25 Figure 25. 48V to 10.8V at 10A Buck Converter 3-Cell LiFePO4 Battery Charger with 2.9h Termination Timer, 1.25A Trickle Charge Current and Charging PFET Thermal Protection 4000f 35 LTC4000 Typical Applications VIN 6V TO 18V 15A MAX 3.3mΩ 2.5mΩ 150µF 22µF ×4 PA1494.362NL 3.3µH 10Ω 1nF 10Ω INTVCC Si7135DP BSC027N04 SENSE+ 22µF ×5 BOOST INTVCC PLLINMODE 100k INTVCC LTC3786 RUN SS 0.1µF FREQ 0.1µF 150µF SW BG PGOOD 4.7µF 1.87M BSC027N04 TG VBIAS 232k VFB GND VOUT 22V, 5A BAS140W SENSE– ITH 12.1k 10mΩ 28.7k 22nF RST CLN IN ITH IID CC IGATE CSP CSN BGATE Si7135DP 10nF 1µF 383k VM 100k BAT OFB LTC4000 ENC CHRG FLT 107k FBG 107k IIMON 10nF IBMON 10nF CX IL CL GND BIAS TMR BFB NTC 4000 F26 22.1k 10µF 10k 22.1k 1µF NTHS0603 N02N1002J 1.87M RNTC 5-CELL Li-Ion BATTERY PACK TENERGY SSIP PACK 30104 Figure 26. 6V to 21V at 5A Boost Converter 5-Cell Li-Ion Battery Charger with C/10 Termination and 0.55A Trickle Charge Current 4000f 36 VIN 18V TO 72V 2.2µF ×2 0.1µF 15.8k 221k FS VCC 681Ω 13.6k 0.04Ω VCC 150pF ISO1 PS2801-1-K BAS516 3.01k 68Ω BAS516 • • • BAS516 1.5k VOUT PDS1040 VOUT 10nF 24.9k 47nF VM 150k IN 10nF IIMON IBMON IL CL ENC CHRG FLT RST ITH CC 100k 100µF ×3 22.1k TMR 100nF LTC4000 CLN 1µF 20mΩ CX NTC FBG BFB OFB BAT BGATE CSN CSP IGATE GND BIAS 22.1k IID SiA923EDJ Figure 27. 18V to 72VIN to 4.2V at 2.0A Isolated Flyback Single-Cell Li-Ion Battery Charger with 2.9h Timer Termination and 0.22A Trickle Charge Current SYNC GND FB OC ITH ISENSE FDC2512 1µF GATE MMBTA42 VCC LTC3805-5 75k SSFLT RUN PDZ6.8B 6.8V 221k TR1 PA1277NL 1µF 10k 115k 115k 309k RNTC 309k 10nF 4000 F27 NTHS0603 N02N1002J SINGLE-CELL Li-Ion BATTERY PACK SiA923EDJ 25mΩ VSYS 4.4V, 2.5A LTC4000 Typical Applications 4000f 37 LTC4000 Package Description UFD Package 28-Lead Plastic QFN (4mm × 5mm) (Reference LTC DWG # 05-08-1712 Rev B) 0.70 ±0.05 4.50 ± 0.05 3.10 ± 0.05 2.50 REF 2.65 ± 0.05 3.65 ± 0.05 PACKAGE OUTLINE 0.25 ±0.05 0.50 BSC 3.50 REF 4.10 ± 0.05 5.50 ± 0.05 RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 4.00 ± 0.10 (2 SIDES) 0.75 ± 0.05 R = 0.05 TYP PIN 1 NOTCH R = 0.20 OR 0.35 × 45° CHAMFER 2.50 REF R = 0.115 TYP 27 28 0.40 ± 0.10 PIN 1 TOP MARK (NOTE 6) 1 2 5.00 ± 0.10 (2 SIDES) 3.50 REF 3.65 ± 0.10 2.65 ± 0.10 (UFD28) QFN 0506 REV B 0.200 REF 0.00 – 0.05 0.25 ± 0.05 0.50 BSC BOTTOM VIEW—EXPOSED PAD NOTE: 1. DRAWING PROPOSED TO BE MADE A JEDEC PACKAGE OUTLINE MO-220 VARIATION (WXXX-X). 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 4000f 38 LTC4000 Package Description GN Package 28-Lead Plastic SSOP (Narrow .150 Inch) (Reference LTC DWG # 05-08-1641) .386 – .393* (9.804 – 9.982) .045 ± .005 28 27 26 25 24 23 22 21 20 19 18 17 1615 .254 MIN .033 (0.838) REF .150 – .165 .229 – .244 (5.817 – 6.198) .0165 ± .0015 .150 – .157** (3.810 – 3.988) .0250 BSC 1 RECOMMENDED SOLDER PAD LAYOUT .015 ± .004 × 45° (0.38 ± 0.10) .0075 – .0098 (0.19 – 0.25) 2 3 4 5 6 7 8 9 10 11 12 13 14 .0532 – .0688 (1.35 – 1.75) .004 – .0098 (0.102 – 0.249) 0° – 8° TYP .016 – .050 (0.406 – 1.270) NOTE: 1. CONTROLLING DIMENSION: INCHES INCHES 2. DIMENSIONS ARE IN (MILLIMETERS) .008 – .012 (0.203 – 0.305) TYP .0250 (0.635) BSC GN28 (SSOP) 0204 3. DRAWING NOT TO SCALE *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 4000f Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 39 LTC4000 Typical Application 5.6Ω IHLP6767GZ ER4R7M01 4.7µH 390pF 3.6Ω B240A VIN 6V TO 36V 12.5A MAX 4mΩ Q2 270µF Q4 B240A Q5 0.22µF TG1 SW1 0.01Ω Q3 Si7135DP 1.24k BG1 SENSE+ SENSE– BG2 SW2 BOOST1 VOUT 15V, 5A 330µF ×2 0.22µF 0.01Ω 1.24k 3.3µF ×5 1800pF 22µF ×2 TG2 BOOST2 DFLS160 DFLS160 INTVCC INTVCC 10µF MODE/PLLIN VIN 1µF 100k LTC3789 VINSNS PGOOD 309k IOSENSE+ IOSENSE– VOUTSNS BZT52C5V6 121k FREQ EXTVCC ILIM 154k VFB RUN ITH SS SGND 10µF PGND1 8.06k 0.01µF 10mΩ 14.7k RST CLN IN ITH 100nF CC IID IGATE CSP CSN BGATE VM 100k Q2: SiR422DP Q3: SiR496DP Q4: SiR4840BDY Q5: SiR496DP BAT OFB LTC4000 ENC CHRG FLT BZX84C3VO 26.7k FBG 118k IIMON 10nF Si7135DP 10nF 1µF 365k IBMON IL 10nF CL TMR CX BFB NTC GND BIAS 1.37M 4-CELL LiFePO4 BATTERY PACK 4000 F28 18.2k 0.1µF 22.1k 1µF RNTC 10k NTHS0603 N02N1002J Figure 28. 6V to 36VIN to 14.4V at 4.5A Buck Boost Converter 4-Cell LiFePO4 Battery Charger with 2.9h Timer Termination and 0.45A Trickle Charge Current Related Parts PART NUMBER DESCRIPTION COMMENTS LTC3789 High Efficiency, Synchronous, 4 Switch Buck-Boost Controller Improved LTC3780 with More Features LT3845 High Voltage Synchronous Current Mode Step-Down Controller with Adjustable Operating Frequency For Medium/High Power, High Efficiency Supplies LT3650 High Voltage 2A Monolithic Li-Ion Battery Charger 3mm × 3mm DFN-12 and MSOP-12 Packages LT3651 High Voltage 4A Monolithic Li-Ion Battery Charger 4A Synchronous Version of LT3650 Family LT3652/LT3652HV Power Tracking 2A Battery Chargers Multi-Chemistry, Onboard Termination LTC4009 High Efficiency, Multi-Chemistry Battery Charger Low Cost Version of LTC4008, 4mm × 4mm QFN-20 LTC4012 High Efficiency, Multi-Chemistry Battery Charger with PowerPath Control Similar to LTC4009 Adding PowerPath Control LT3741 High Power, Constant Current, Constant Voltage, Step-Down Controller Thermally Enhanced 4mm × 4mm QFN and 20-Pin TSSOP 4000f 40 Linear Technology Corporation LT 0411 • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7417 (408) 432-1900 ● FAX: (408) 434-0507 ● www.linear.com LINEAR TECHNOLOGY CORPORATION 2011