Toggles Series G3B Keylocks Programmable Illuminated PB Pushbuttons Rockers General Specifications Electrical Capacity (Resistive Load) C Logic Level: Other Ratings Contact Resistance: Insulation Resistance: Dielectric Strength: Mechanical Life: Electrical Life: Nominal Operating Force: Travel: Materials & Finishes Actuator: Case: Sealing Rings: Movable Contacts: Stationary Contacts: Base: Terminals: Rotaries Slides Tactiles Tilt Touch Indicators Accessories Supplement Ultra-Miniature Process Sealed SMT Pushbuttons Environmental Data Operating Temperature Range: Humidity: Vibration: Shock: Installation Mounting: Coplanarity: Processing Soldering: Cleaning: Standards & Certifications Flammability Standard: C52 0.4VA maximum @ 28V AC/DC maximum (Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V) Note: Find additional explanation of operating range in Supplement section. 80 milliohms maximum 500 megohms minimum @ 500V DC 500V AC minimum for 1 minute minimum 50,000 operations minimum 50,000 operations minimum 2.0N Pretravel: .024” (0.6mm); Overtravel: .019” (0.5mm); Total Travel: .043” (1.1mm) Polyphenylene sulfide (UL94V-0) Polyphenylene sulfide (UL94V-0) Nitrile butadiene rubber Phosphor bronze with gold plating Phosphor bronze with gold plating Polyphenylene sulfide (UL94V-0) Phosphor bronze with gold plating –30°C through +85°C (–22°F through +185°F) 90 ~ 95% humidity for 96 hours @ 40°C (104°F) 10 ~ 500Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning in 1 minute; 3 right angled directions for 2 hours 50G (490m/s2) acceleration (tested in 6 right angled directions, with 5 shocks in each direction) It is recommended that the body of models for upright mounting without bracket be fastened to a panel or similar support for protection of solder joints from mechanical stress. See specifications in Terms & Acronyms in Supplement section. Reflow Soldering Recommended. See Profile B in Supplement section. Manual Soldering: See Profile B in Supplement section. Automated cleaning. See Cleaning specifications in Supplement section. UL94V-0 actuator, case & base The G3B Series pushbuttons have not been tested for UL recognition or CSA certification. These switches are designed for use in a low-voltage, low-current, logic-level circuit. When used as intended in a logic-level circuit, the results do not produce hazardous energy. www.nkk.com Toggles Series G3B Rockers Distinctive Characteristics Ultra-miniature size allows high density mounting, and extremely light weight of 0.6 gram makes these switches ideal for handheld equipment. C Programmable Illuminated PB Tape-reel and stick-tube packaging allow rapid automated placement of surface mount devices. Tape-reel packaging meets EIA-481-D Standard. Pushbuttons Ultra-Miniature Process Sealed SMT Pushbuttons Keylocks Heat resistant resin used for housing, base, and plunger allows vapor phase and infrared convection reflow soldering. Slides Rotaries Combination of design features achieves total seal and allows automated processing techniques, including flux cleaning procedures: one-piece bushing and housing, rubber seals surrounding actuator and base, epoxy at joint of case and base, and molded-in, epoxy-sealed terminals. Tactiles Award-winning STC contact mechanism with benefits unavailable in conventional mechanisms: smoother, positive detent actuation, increased contact stability and unparalleled logic-level reliability. (Additional STC details in Terms & Acronyms; see Supplement section.) Tilt Gull-wing terminals provide mechanical stability during soldering and simplified solder joint inspection. Touch Coplanarity: all considered surfaces must lie between two parallel planes that area maximum distance apart of .0059” (0.15mm). (Additional coplanarity details in Terms and Acronyms in the Supplement section.) Supplement Accessories Indicators Actual Size www.nkk.com C53 Series G3B Toggles Ultra-Miniature Process Sealed SMT Pushbuttons TYPICAL SWITCH ORDERING EXAMPLE C 1 5 A Poles 1 SPDT 2 DPDT A ON Gull Wing for Upright Mount B Gull Wing for Upright with Bracket H Gull Wing for Right Angle .130” (3.3mm) Long (ON) Colors P Plunger Circuits 5 B Terminals Black B White C Red Slip-on Cap .157” (4.0mm) Diameter X (For installation after processing only) Packaging No Partitioned Tray for Upright & Code Right Angle - Any Quantity Rotaries A Optional Caps ( ) = Momentary Keylocks Programmable Illuminated PB Pushbuttons Rockers G3B R Tape-Reel for Right Angle Only 500 Pieces/Reel S Stick-Tube for Upright Mount 50 Pieces/Stick Process Compatible Cap .157” (4.0mm) Diameter (Combines with R or S packaging only) Y Slides Packaging details at end of G3B Series DESCRIPTION FOR TYPICAL ORDERING EXAMPLE Tactiles G3B15AB .130” (3.3mm) Long Plunger Gull Wing Terminals for Upright with Bracket Mount Tilt Packaged in Partitioned Tray POLES & CIRCUITS Touch Indicators Accessories Supplement SPDT ON-(ON) Circuit Plunger Position ( ) = Momentary Normal Down Connected Terminals Normal Throw & Schematics Down Note: Pole Model SP G3B15 ON (ON) 5-6 5-4 SPDT DP G3B25 ON (ON) 5-6 2-3 5-4 2-1 DPDT C54 Terminal numbers are not actually on the switch. 5 (COM) 5 www.nkk.com 6 4 4 (COM) 6 1 2 3 Series G3B Toggles Ultra-Miniature Process Sealed SMT Pushbuttons PLUNGER & OPTIONAL CAPS Available with bulk packaging only. Cap must be installed after processing. (2.0) Dia .079 (3.3) .130 (4.0) Dia .157 (3.8) .150 (2.4) .094 Finish: Glossy Factory assembled. Available with tape-reel or stick-tube packaging only. Actual Size Material: Polyamide Process Compatible Cap .157” (4.0mm) Diameter Caution: Pulling force specification for this cap is not warranted after reflow processing. Material: Polyamide Finish: Glossy A Cap Colors Available: B Black C White Red TYPICAL SWITCH DIMENSIONS Single & Double Pole Support Legs (8.5) 5 COM .335 6 (2.0) Dia .079 (0.7) .028 Slot (1.5) .059 (3.3) .130 4 2 5 6 3 (0.1) .004 (7.6) .299 (7.6) .299 Single & Double PoleUpright Mounting with Bracket (0.25) Typ .010 (4.0) Dia .157 (3.8) .150 Support Legs 1 (11.0) 5 COM .433 6 (2.0) Dia .079 (0.7) .028 Slot (1.5) .059 (3.3) .130 (9.0) .354 (0.5) Typ .020 (0.9) Typ .035 (0.1) .004 (1.2) Typ .047 (3.8) .150 (1.2) Typ .047 4 (5.08) .200 (5.0) .197 G3B25AP 4 2 5COM 6 3 (11.0) .433 (0.5) Typ .020 (0.9) Typ .035 Tilt (8.5) .335 (0.5) Typ .020 (0.5) Typ .020 (9.0) .354 COM Rotaries 1 4 (5.08) .200 (0.6) Typ .024 Keylocks (4.0) Dia .157 (5.0) .197 Upright Mounting (0.25) Typ .010 C Tactiles (0.6) Typ .024 Rockers Y Pushbuttons AT4063 Slip-on Cap .157” (4.0mm) Diameter X Programmable Illuminated PB .130” (3.3mm) Long Plunger Slides A (7.6) .299 (7.6) .299 (3.8) Typ .150 Right Angle Mounting (4.0) Dia .157 Indicators (2.54) Typ (1.25) Typ .100 .049 (11.0) .433 (2.0) Dia .079 (0.5) Typ .020 (0.9) Typ .035 (0.55) .022 Single Pole Double Pole (5.55) .219 (5.55) .219 (0.25) Typ .010 (8.5) .335 6 (0.25) .010 5 4 COM 6 3 5 2 4 1 (0.1) .004 www.nkk.com Accessories (9.0) .354 COM (0.1) .004 Supplement Slot (1.5) .059 (3.3) .130 Touch G3B15AB G3B15AH C55 Toggles Series G3B (1.7) Typ .067 (2.54) Typ .100 Single Pole Double Throw (0.635) .025 (0.7) Typ .028 (1.7) Typ .067 (2.54) Typ .100 4 Rotaries (0.635) .025 (0.7) Typ .028 6 Support Pads (6.0) .236 (2.54) Typ .100 1 2 (0.635) Typ .025 (0.7) Typ .028 (6.0) .236 Partitioned Tray for Upright & Right Angle Slides Any quantity Touch Tilt Tactiles If the G3 upright models are ordered in less than 50-piece increments or the right angle models in less than 500-piece increments, the switches are packaged in a partitioned tray. No code is required. R Tape-Reel for Right Angle Indicators 500 pieces per reel Accessories Switches must be ordered in 500-piece increments when tape-reel packaging is selected. Supplement This packaging meets EIA-481-D Standard for “16mm and 24mm Embossed Carrier Taping of Surface Mount Components for Automatic Handling.” C56 (6.0) .236 (3.8) .150 www.nkk.com (9.75) .384 (1.55) Typ .061 (1.1) Typ .043 Right Angle Mounting (1.1) Typ .043 (9.75) .384 2 3 6 (6.0) .236 (9.75) .384 (1.55) Typ .061 (3.8) .150 (1.7) Typ .067 (2.54) Typ .100 4 5 (0.635) .025 (0.7) Typ .028 (3.0) .118 6 (1.55) Typ .061 (1.1) Typ .043 1 4 5 3 6 Support Pads (5.08) .200 6 (1.7) Typ .067 4 (1.1) Typ .043 5 PACKAGING No Code (3.8) .150 4 (5.08) .200 5 (0.635) Typ .025 (0.7) Typ .028 Upright Mounting with Bracket (1.7) Typ .067 (2.54) Typ .100 5 C Double Pole Double Throw Upright Mounting Keylocks Programmable Illuminated PB Pushbuttons Rockers Pad Layouts for Surface Mount Terminals Ultra-Miniature Process Sealed SMT Pushbuttons (9.75) .384 (1.55) Typ .061 (3.8) .150 1 4 2 5 3 6 (1.7) Typ .067 (1.27) Typ .050 (0.635) Typ .025 (0.7) Typ .028 (3.0) .118 Series G3B Toggles Ultra-Miniature Process Sealed SMT Pushbuttons PACKAGING (CONTINUED) 50 pieces per stick Switches must be ordered in 50-piece increments when stick-tube packaging is selected. Programmable Illuminated PB C Tape-Reel Packaging for Right Angle Mount Keylocks Each tape-reel of 550 pockets contains 500 switches. Minimum Leader Length: 7.87” (200mm) Minimum Trailer Length: 1.97” (50mm) Overall Dia (330.0) 13.0 (21.0) Dia .827 (2.0) .079 (24.0) .945 (11.5) .453 Part No. (0.4) .016 (6.0) .236 (17.8) .701 (2.1) Dia Typ .083 (2.0) .079 Direction of Feed Tape Dimensions Tilt Reel Dimensions (13.9) .547 (8.6) .339 (1.5) R .059 Terminal #1 (24.4) .961 Rotaries (1.5) Dia Typ .059 Slides (78.49) Dia 3.090 (13.0) Dia .512 (2.0) Typ .079 (4.0) Typ .157 (16.0) Typ .630 Tactiles (1.75) .069 (2.0) Typ .079 Pushbuttons Rockers Stick-Tube for Upright Mount S Stick-Tube Packaging for Upright Mount (7.7) .303 Indicators L = Length Touch Each stick-tube contains 50 switches. G3B Upright (code P) Accessories (15.3) .602 18.31” (465mm) G3B Upright with Bracket (code B) (9.8) .386 L Supplement 21.26” (540mm) Stick-Tube Dimensions www.nkk.com C57