FX-500 Low Jitter Frequency Translator FX-500 Description The FX-500 is a complete crystal-based frequency translator used in communications applications where low jitter is paramount. Performance advantages include superior jitter performance, high output frequencies and small package size. Advanced custom ASIC technology results in a highly robust, reliable and predictable device. The device is packaged in a 6 pin J-Lead ceramic package with a hermetic seam welded lid. Features • • • • • • • • • • • Applications Complete Frequency Translator to 77.760 MHz 3.3 Volt or 5.0 Volt Supply Capable of locking to an 8kHz pulse/ BITS clock Tri-State Output allows board test Lock Detect J-lead Ceramic Package Advanced Custom ASIC Technology Absolute Pull Range Performance to ±100 ppm CMOS output Commercial or Industrial Temperature Range EIA Compatible Tape and Reel Packaging • • • • • Frequency Translation, Clock Smoothing Telecom - SONET/SDH/ATM Datacom - DSLAM, DSLAR, Access Nodes Cable Modem Head End Base Station - GSM, CDMA Block Diagram LD (5) VCC (6) FIN (1) ÷ Tri-State (2) Phase Detector & LD Loop Filter VCXO FOUT (4) ÷ GND (3) Figure 1. Functional block diagram 1 of 7 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Rev: 14Aug2009 Performance Specifications Table 1. Electrical Performance Parameter Frequency Input Frequency Capture Range (Ordering Option) Output Frequency Supply 1 Voltage (Ordering Option) Current (No Load) Input Signal Input Low Level Voltage Input High Level Voltage Pulse Width Output 2 Output High Level Voltage Ouput Low Level Voltage Rise Time Fall Time Duty Cycle 3 ≤ 60 MHz > 60MHz Leakage Current of Input Loop Bandwidth (-3dB), 8kHz input Jitter, 8kHz to 77.76MHz rms p-p Symbol Min FIN APR FOUT 0.001 ±50 1.0 VDD VDD IDD 3.0 4.5 VIL VIH VOH VOL tR tF D Typical 3.3 5.0 IC Units 77.76 ±100 77.76 MHz ppm MHz 3.6 5.5 40 V V mA 0.3*VDD V V ns 0.7*VDD 6 0.9*VDD 1.8 1.8 45 40 BW Maximum -1 0.1*VDD 3.0 3.0 V V ns ns 55 60 % % 1 μA 10 Hz 4.7 44 0.003 ps ps UI 1. A 0.1 μF low frequency tantalum bypass capacitor in parallel with a 0.01 μF high frequency ceramic capacitor is recommended. 2. Figure 2 defines the waveform parameters. Figure 3 illustrates the standard test conditions under which these parameters are specified and tested. 3. Duty cycle is defined as (on time÷period), with VS = VDD/2, per figure 2. Duty cycle is measured with a 15pf load per figure 3. 4. Other frequencies may be available, please contact factory. Figure 2. Output Waveform 2 of 7 Figure 3. Output Test Conditions (25 ± 50C ) Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Rev: 14Aug2009 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can permanently damage the device. Functional operation is not implied at these or any other conditions in excess of conditions represented in the operational sections of this data sheet. Exposure to the maximum ratings for the extended periods may adversely affect device reliability. Table 2. Absolute Maximum Ratings Parameter Power Supply Storage Temperature Symbol Ratings Unit VDD TSTR 7 -55 to 125 V 0C Reliability The FX-500 is capable of meeting the following qualification tests Table 3. Environmental Compliance Parameter Conditions Mechanical Shock Mechanical Vibration Lead Solderability Gross and Fine Leak MIL-STD-883, M2002/TEST A MIL-STD-883, M2007/TESTA MIL-STD-883, M2003 MIL-STD-883, M1014 Handling Precautions Although ESD protection circuitrry has been designed into the the FX-424, proper precautions should be taken when handling and mounting. VI employs a human body model and a charged-device model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance=1.5Kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes Table 4. Predicted ESD R$atings Model Human Body Model Charged Device Model 3 of 7 Minimum 1000 V 1000 V Conditions MIL-STD 883, Method 3015 JEDEC, JESD22-C101 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Rev: 14Aug2009 Table 5. Reflow Profile (IPC/JEDEC J-STD-020C) Parameter Symbol Value tS 60 sec Min, 180 sec Max PreHeat Time RUP 3 0C/sec Max tL 60 sec Min, 150 sec Max tAMB-P 480 sec Max tP 20 sec Min, 40 sec Max RDN 6 0C/sec Max Ramp Up Time Above 217 0C Time To Peak Temperature Time At 260 0C Ramp Down The device has been qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the PbFree small body requirements. The temperatures refer to the topside of the package, measured on the package body surface. The FX-500 device is hermetically sealed so an aqueous wash is not an issue. Figure 4. Suggested IR Profile Table 6. Tape and Reel Information Tape Dimensions (mm) Reel Dimensions (mm) A B C D E F G H I J K L #/Reel 24 11.5 1.5 4 12 1.78 21 13 100 5 25 330 200 Figure 5. Tape and Reel 4 of 7 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Rev: 14Aug2009 FX500 YWW CCC-CCCC XX-XX Y = Year WW = Week C = Option Codes XX = FREQUENCY CODE (SEE ORDERING INFO) Inch [mm] Figure 6. Outline Drawing and Pad Layout Table 7. Pin Functions Pin # Symbol Function 1 fIN Input Frequency ! 2 Tri-State 3 GND Case and Electrical Ground 4 fo Output Frequiency 2 5 LD 6 VDD Logic Low = Output Disable LOgic High = Output Enabled Lock Detect Power Supply Voltage 1. Tristate is driven to logic high or logic low; there is no internal pull up or pull down resistor. 2. LD is an open collector output requiring a 30k ohm pullup resistor to VDD. LD output is logic high under locked condition, logic low for no input at fIN, and for “out-of-lock” condition LD transitions between logic low and logic high at the phase detector 5 of 7 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Rev: 14Aug2009 Ordering Information Table 8. Standard Frequencies 0.0010 A1 1.0000 BB 9.2160 CH 19.6990 DK 32.7680 H3 49.1520 J7 0.0020 AR 1.0240 B2 9.7200 C8 19.7190 DH 33.0000 H7 49.4080 J2 0.0032 AG 1.2150 BU 9.7500 CE 19.9219 ED 33.3330 HC 50.0000 JD 0.0040 A2 1.2288 BK 9.8304 C1 20.0000 E2 34.3680 H6 50.0480 KD 0.0080 A3 1.2500 BG 10.0000 C4 20.1416 E3 34.5600 HB 51.2000 LL 0.0095 AU 1.3333 BF 10.2300 DP 20.4800 E4 36.8640 HG 51.8400 J4 0.0100 A6 1.5000 BE 10.2400 DM 20.5444 EF 37.0560 H4 52.0000 JP 0.0156 AL 1.5360 BV 10.4143 DV 20.7135 E1 37.1250 H9 53.3300 JU 0.0157 AD 1.5440 B3 10.4582 DU 20.8286 EB 37.5000 HK 54.7460 JL 0.0158 AC 1.9200 B1 10.4872 DN 20.8286 EG 38.8800 H5 55.0000 JX 0.0160 A4 2.0000 B8 10.9490 DG 20.9165 EH 39.0625 HH 60.0000 JR 0.0240 BX 2.0480 B4 10.9500 DJ 21.0051 EJ 39.3216 HD 61.3800 KY 0.0250 BR 2.3040 BD 11.1840 DF 22.0000 E9 39.8438 HJ 61.4400 J5 0.0320 BW 2.4576 BJ 12.2880 D8 22.1048 EK 40.0000 JF 62.2080 J8 0.0400 AP 2.5000 BM 12.3077 DY 22.2171 E5 40.2831 KK 62.5000 J9 0.0441 AA 2.5575 B9 12.3520 D1 22.5792 E8 40.9600 J1 62.9145 LE 0.0480 AB 3.0880 B6 12.8000 D2 24.0000 EC 41.0889 KM 63.3600 JJ 0.0481 AV 3.2400 BL 13.0000 D3 24.5760 E6 41.6571 KP 63.8976 JN 0.0500 BT 3.2500 BC 13.5000 DT 24.7040 E7 41.8329 KT 64.0000 JT 0.0640 A5 3.3750 BH 14.8352 DL 25.0000 F7 42.0000 JB 64.1520 JH 0.0800 A9 3.8400 B7 15.0000 D4 25.1658 F8 42.0102 KV 65.5360 J6 0.1000 AH 4.0000 BN 15.0336 DR 25.6000 F6 42.5000 JC 66.0000 JA 0.1280 AX 4.0960 B5 15.3600 DW 25.9200 F2 42.6600 JZ 70.0000 KB 0.2430 A8 5.0000 C6 16.0000 D9 26.0000 F3 44.2095 KX 70.6560 KC 0.2560 AM 5.1200 CD 16.3840 D5 27.0000 F4 44.4343 LF 71.6100 KF 0.3200 AW 6.1440 CG 17.1840 DE 27.6480 FB 44.6218 JW 73.7280 K8 0.3840 AY 6.2914 CC 18.4320 D7 28.7040 F1 44.7360 J3 74.1250 K1 0.4000 AF 6.2915 CF 18.5280 DC 29.4912 F5 44.9280 JE 74.1758 KA 0.4800 AK 6.3120 C7 18.7500 EE 29.5000 F9 45.1584 JG 74.2500 K7 0.5000 BP 6.4800 C2 19.2000 DD 30.0000 HE 45.8240 JM 75.0000 KH 0.5120 AJ 6.7500 CB 19.3927 DX 30.7200 H1 46.0379 LG 76.8000 K4 0.6555 AE 7.6800 C9 19.4400 D6 30.8800 HF 46.7200 JK 77.7600 K2 0.7720 AT 7.7760 C5 19.5313 DZ 31.2500 H8 46.8750 JY 0.9600 A7 8.1920 C3 19.6608 DB 32.0000 H2 48.0000 JV Note 1: Other frequencies are available upon request, please contact VI for details SS is code for non-standard frequencies, list the frequency after the part number. Note 2: Not all combinations are possible. Note 3: Output frequency must be equal to or greater than the input frequency. The ratio of fo/fIN must be an integer. Also, the output frequency must be equal to greater than 100 kHz. 6 of 7 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Rev: 14Aug2009 Ordering Information F X - 5 0 0 - E A E - K N N N - XX - XX Output Frequency (See Above) Product Family FX: Frequency Translator Input Frequency (See Above) Package 500: 9.0 x 14 x 4.5 mm Input D: 5.0 Vdc ±10% E: 3.3 Vdc ±10% Performance Options N: Standard A: Improved Phase Noise Output A: CMOS Loop Filter BW N: Internal Loop Filter Operating Temperature E: -40 to 85 °C T: 0 to 70 °C Absolute Pull Range K: ± 50 ppm P: ± 80 ppm S: ± 100 ppm Factory Use N: Standard Note: Not all combinations will be availabe - check with the factory to determine the optimum configuration for your application For Additional Information, Please Contact USA: Europe: Asia: Vectron International 267 Lowell Road Hudson, NH 03051 Tel: 1.888.328.7661 Fax: 1.888.329.8328 Vectron International Landstrasse, D-74924 Neckarbischofsheim, Germany Tel: +49 (0) 3328.4784.17 Fax: +49 (0) 3328.4784.30 Vectron International 1F-2F, No 8 Workshop, No 308 Fenju Road WaiGaoQiao Free Trade Zone Pudong, Shanghai, China 200131 Tel: 86.21.5048.0777 Fax: 86.21.5048.1881 Disclaimer Vectron International reserves the right to make changes to the product(s) and or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. 7 of 7 Vectron International • 267 Lowell Road, Hudson, NH 03051 • Tel: 1-88-VECTRON-1 • http://www.vectron.com Rev: 14Aug2009