AME AME8804 n General Description The AME8804 family of positive, linear regulators feature low ground current (35µA typ.) with low dropout voltage, making them ideal for battery applications. The space-saving SOT-26/TSOT-26 and SOT-25/TSOT-25 packages are attractive for "Pocket" and "Hand Held" applications. These rugged devices have both Thermal Shutdown, and Current Fold-back to prevent device failure under the "Worst" operating conditions. The SOT-26/TSOT-26 version also features a "Power Good" detector, which pulls low when the output is out of regulation. 300mA CMOS LDO n Functional Block Diagram IN OUT Overcurrent Shutdown Thermal Shutdown EN Vref x110% AMP PG ADJ The AME8804 is stable with an output capacitance of 2.2µF or greater. n Features Vref x90% Vref =1.215V l Very Low Dropout Voltage GND l Guaranteed 300mA Output l Accurate to within 1.5% l Typical 35µA Ground Current l Over-Temperature Shutdown n Typical Application l Current Limiting l Short Circuit Current Fold-back l Power Good Detector (6 pin version only) l Power-Saving Shutdown Mode IN PG l Space-Saving SOT-26/TSOT-26 and SOT-25 / TSOT-25 l Adjustable Output Voltages l Low Temperature Coefficient l All AME's Lead Free Products Meet RoHS Standards C1 5V OUT OUT EN IN AME8804 GND ADJ C2 R1 100p 1µF C3 2.2µF R2 n Applications l Instrumentation l Portable Electronics V OUT = 1.215 (R1 +R2)/R2 C2 is unnecessary when R1 or R2 < 20K PG pin is only available in the SOT-26 package option l Wireless Devices l Cordless Phones l PC Peripherals l Battery Powered Widgets l Electronic Scales Rev.K.04 1 AME AME8804 300mA CMOS LDO n Pin Configuration SOT-26/TSOT-26 Top View 6 5 4 AME8804 SOT-25 /TSOT-25 Top View AME8804AEEY 5 4 1. IN 1. IN 2. GND 2. GND 3. EN AME8804 4. PG 2 3 6. OUT 3. EN 4. ADJ 5. ADJ 1 AME8804AEEV 5. OUT 1 2 3 * Die Attach: * Die Attach: Non-Conductive Epoxy Conductive Epoxy SOT-25 /TSOT-25 Top View 5 4 AME8804BEEVADJ 1. EN 2. GND AME8804 3. IN 4. OUT 5. ADJ 1 2 3 * Die Attach: Conductive Epoxy n Pin Description Pin Name IN GND 2 Pin Description Input voltage pin. It should be decoupled with 1µF or greater capacitor. Ground connection pin. EN Enable pin. When pulled low, the PMOS pass transistor turns off, current consuming less than 1µA. PG Power-Good output. This open-drain output is low when OUT is out of regulation. OUT LDO voltage regulator output pin. It should be decoupled with a 1µF or greater value low ESR ceramic capacitor. ADJ Feedback output voltage for adjustable device. Rev.K.04 AME AME8804 300mA CMOS LDO n Ordering Information AME8804 x x x x x Special Feature Number of Pins Package Type Operating Ambient Temperature Range Product Grade or Option Product Grade Operating Ambient or Option Temperature Range A: ADJ E: -40OC to +85OC Package Type E: SOT-2X Number of Pins V: 5 Y: 6 Special Feature L: Low Profile Y: Lead Free & Low Profile Z: Lead Free n Ordering Information Marking* Output Voltage Package Operating Ambient Temperature Range AME8804AEEY AAUww Adjustable SOT-26 - 40oC to +85oC AME8804AEEYL AAUww Adjustable TSOT-26 - 40oC to +85oC AME8804AEEYY AAUww Adjustable TSOT-26 - 40oC to +85oC AME8804AEEYZ AAUww Adjustable SOT-26 - 40oC to +85oC AME8804AEEV AJCww Adjustable SOT-25 - 40oC to +85oC AME8804AEEVL AJCww Adjustable TSOT-25 - 40oC to +85oC AME8804AEEVY AJCww Adjustable TSOT-25 - 40oC to +85oC AME8804AEEVZ AJCww Adjustable SOT-25 - 40oC to +85oC Part Number Note: ww represents the date code and pls refer to Date Code Rule on Package Dimension. * A line on top of the first letter represents lead free plating such as AAUww Please consult AME sales office or authorized Rep./Distributor for output voltage and package type availability. Rev.K.04 3 AME AME8804 300mA CMOS LDO n Ordering Information (contd.) AME8804 x x x x xxx x Special Feature Output Voltage Number of Pins Package Type Operating Ambient Temperature Range Pin Configuration Pin Configuration B: 1. EN 2. GND (TSOT-25) 3. IN 4. OUT 5. ADJ Operating Ambient Temperature Range Package Type Number of Pins Output Voltage E: -40OC to +85OC E: SOT-2X V: 5 ADJ: Adjustable (SOT-25) Special Feature Z: Lead Free Y: Lead Free & Low Profile n Ordering Information Part Number Marking* Output Voltage Package Operating Ambient Temperature Range AME8804BEEVADJZ BJIww Adjustable SOT-25 - 40oC to +85oC AME8804BEEVADJY BJIww Adjustable TSOT-25 - 40oC to +85oC Note: ww represents the date code and pls refer to Date Code Rule on Package Dimension. * A line on top of the first letter represents lead free plating such as BJIww Please consult AME sales office or authorized Rep./Distributor for output voltage and package type availability. 4 Rev.K.04 AME AME8804 300mA CMOS LDO n Absolute Maximum Ratings Parameter Maximum Unit Input Voltage -0.3 to +8 V EN Voltage -0.3 to +8 V Output Voltage -0.3 to VIN + 0.3 V PG Voltage -0.3 to VIN + 0.3 V Output Current PD / (V IN - VOUT) mA B* ESD Classification Caution: Stress above the listed absolute maximum rating may cause permanent damage to the device. * HBM B:2000V~3999V n Recommended Operating Conditions Parameter Symbol Rating Unit Ambient Temperature Range TA - 40 to +85 o Junction Temperature Range TJ - 40 to +125 o Storage Temperature Range TSTG - 65 to +150 o C C C n Thermal Information Parameter Thermal Resistance* (Junction to Case) Thermal Resistance (Junction to Ambient) Internal Power Dissipation Package SOT-25 TSOT-25 SOT-26 TSOT-26 SOT-25 TSOT-25 SOT-26 TSOT-26 SOT-25 TSOT-25 SOT-26 TSOT-26 Die Attach Symbol Conductive Epoxy Non-Conductive Epoxy 81 140 o C/W 260 θJA 280 Conductive Epoxy Non-Conductive Epoxy Unit θJC Conductive Epoxy Non-Conductive Epoxy Maximum 400 PD mW 400 Maximum Junction Temperature 150 o C Solder Iron (10 Sec)** 350 o C * Measure θJC on center of molding compound if IC has no tab. ** MIL-STD-202G 210F Rev.K.04 5 AME AME8804 300mA CMOS LDO n Electrical Specifications TA = 25OC, VIN=5V unless otherwise noted Parameter Symbol Input Voltage VIN Output Voltage Accuracy VO Dropout Voltage Output Current Current Limit Short Circuit Current, Note2 Ground Pin Current Line Regulation Load Regulation Over Temperature Shutdown Over Temperature Hysterisis VO Temperature Coefficient Power Supply Rejection VDROPOUT -1.5 1.5 % 1300 See 400 chart 300 2.0V<VO(NOM) <=2.8V VO>1.2V 300 ISC VO<0.8V 150 IGND IO=1mA to 300mA 35 REGLOAD OTS IO=5mA mA 450 mA 300 mA µA 0.15 % 0.02 0.1 % 0.2 1 VO < 2.0V VIN =VO+1 to VO+2 VO >= 2.0V IO=1mA to 300mA mV % 150 o OTH 30 o TC 30 PSRR IADJ ADJ Reference Voltage VREF Shutdown Output Voltage V ILIM REGLINE Units 7 300 ADJ Input Bias Current Shutdown Supply Current VO=VO(NOM) -2.0% Typ Max Note 1 1.5V<VO(NOM) <=2.0V IO=300mA IO eN EN Input Bias Current IO=1mA Min 2.8V<VO(NOM) <3.8V VO>1.2V Output Voltage Noise EN Input Threshold Test Condition C ppm/oC f=100Hz 60 f=1kHz 50 f=10kHz 20 Co=2.2µF 30 µVrms 1 µA IO=100mA CO=2.2µF f=10Hz to 100kHz IO=10mA,CBYP=0µF C dB 1.2 1.215 1.23 V VEH VIN =2.7V to 7V 2.0 Vin V VEL VIN =2.7V to 7V 0 0.4 V IEH VEN =VIN , VIN =2.7V to 7V 0.1 µA IEL VEN =0V, VIN =2.7V to 7V 0.5 µA ISD VIN =5V, VO=0V, VEN <VEL VO,SD IO=35µA,VEN <VEL Output Under Voltage VUV Output Over Voltage VOV PG Leakage Current 0.5 0 1 µA 0.1 V 85 %VO(NOM) 115 ILC VPG=7V 1 %VO(NOM) µA PG Voltage Rating VPG VO in regulation 7 V PG Voltage Low VOL ISINK=0.4mA 0.4 V Note1: V IN(MIN)=VOUT+VDROPOUT Note2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input voltage must be applied before a current source load is applied. 6 Rev.K.04 AME AME8804 300mA CMOS LDO n Detailed Description n Enable The AME8804 family of CMOS regulators contain a PMOS pass transistor, voltage reference, error amplifier, over-current protection, thermal shutdown, and Power Good detection circuitry. The Enable pin normally floats high. When actively, pulled low, the PMOS pass transistor shuts off, and all internal circuits are powered down. In this state, the quiescent current is less than 1µA. This pin behaves much like an electronic switch. The P-channel pass transistor receives data from the error amplifier, over-current shutdown, and thermal protection circuits. During normal operation, the error amplifier compares the output voltage to a precision reference. Over-current and Thermal shutdown circuits become active when the junction temperature exceeds 150oC, or the current exceeds 300mA. During thermal shutdown, the output voltage remains low. Normal operation is restored when the junction temperature drops below 120oC. The AME8804 switches from voltage mode to current mode when the load exceeds the rated output current. This prevents over-stress. The AME8804 also incorporates current foldback to reduce power dissipation when the output is short circuited. This feature becomes active when the output drops below 0.8volts, and reduces the current flow by 65%. Full current is restored when the voltage exceeds 0.8 volts. n Power Good The AME8804 (SOT-26/TSOT-26 package only) includes the Power Good feature. When the output is not within +10% of the specified voltage, it pulls low. This can occur under the following conditions: 1) Input Voltage too low. 2) During Over-Temperature. 3) During Over-Current. 4) If output is pulled up. (Note: PG pin is an open-drain output.) n External Capacitors The AME8804 is stable with an output capacitor to ground of 2.2µF or greater. Ceramic capacitors have the lowest ESR, and will offer the best AC performance. Conversely, Aluminum Electrolytic capacitors exhibit the highest ESR, resulting in the poorest AC response. Unfortunately, large value ceramic capacitors are comparatively expensive. One option is to parallel a 0.1µF ceramic capacitor with a 10µF Aluminum Electrolytic. The benefit is low ESR, high capacitance, and low overall cost. A second capacitor is recommended between the input and ground to stabilize Vin. The input capacitor should be at least 0.1µF to have a beneficial effect. All capacitors should be placed in close proximity to the pins. A "Quiet" ground termination is desirable. This can be achieved with a "Star" connection. Rev.K.04 7 AME AME8804 300mA CMOS LDO Ground Current vs. Input Voltage Load Step (1mA-300mA) 45 VO (5mV/DIV) 85 C 35 30 25 O 25 C 20 15 10 5 0 0 1 2 3 4 5 C L =2.2µF C IN =2.2µF Output O IL(200mA/DIV) Ground Current (µ A) 40 6 7 I Load 0 8 TIME(20mS/DIV) Input Voltage (V) Power Supply Rejection Ratio Chip Enable Transient Response Enable (2V/DIV) 0 -10 -30 C L=2µF R L=10Ω 0 -40 -50 10mA 100mA -60 -70 100 µ A 100 µ A 1mA Output (1V/DIV) PSRR (dB) 100mA CL=2.2µF Tantalum Tantalum C BYP=0 -20 0 -80 10 1K 100K 10M TIME (1mS/DIV) Frequency (Hz) 1200 1000 1000 800 IO=100mA 600 IO =200mA 400 IO=300mA 0 1.31.5 VOUT=1.3V 800 600 2 3 Output Voltage (V) 4 VOUT=1.5V VOUT=1.8V 400 200 200 8 Drop Out Voltage vs. Load Current 1200 Dropout Voltage (mV) Drop Out Voltage (m V) Drop Out Voltage vs. Output Voltage 0 Top to Bottom VOUT=3.0V VOUT=3.3V VOUT =2.3V VOUT=3.5V VOUT =2.5V VOUT =2.8V 50 100 V OUT=3.8V V OUT=4.0V 150 200 250 300 Load Current (mA) Rev.K.04 AME AME8804 300mA CMOS LDO Safe Operating Area Vo (1mV/ DIV) Output Current (mA) Noise Measurment SOT-26 300 SOT-25 100 10 0.1 TIME (20mS/DIV) I OUT (200mA/DIV) 0 R LOAD=6.6 Ω VOUT (1V/DIV) 0 0 0 TIME (2mS/DIV) TIME (0.5Sec/DIV) Line Transient Response VIN(1V/DIV) Current Limit Response RLOAD=3.3Ω 0 TIME (2mS/DIV) VOUT (10mV/DIV) 0 VOUT(1V/DIV) IOUT (200mA/DIV) 8.0 Overtemperature Shutdown R LOAD =100 Ω R SHORT =0.1 Ω Vout (1V/DIV) ILoad (400mA/DIV) Short Circuit Response Rev.K.04 1.0 Input-Output Voltage Differential (V) C LOAD =2.2µF I LOAD =1mA V OUTDC =3.3V V INDC =4.5V TIME (200mS/DIV) 9 AME AME8804 300mA CMOS LDO Stability vs. ESR vs. ILoad Stability vs. ESR vs. ILoad 10000 10000 Unstable Region Unstable Region 1000 1000 CL=1µF 10 Stable Region CL=2µF 100 ESR ( Ω ) ESR ( Ω ) 100 10 1 1 0.1 0.1 Stable Region Untested Region Untested Region 0.01 0.01 0 50 100 150 0 200 50 150 200 ILOAD (mA) ILOAD (mA) Stability vs. ESR vs. ILoad Stability vs. ESR vs. ILoad 10000 10000 Unstable Region Unstable Region 1000 1000 C L=10µF C L=3µF 10 100 ESR ( Ω ) 100 ESR ( Ω ) 100 Stable Region 10 Stable Region 1 1 0.1 Untested Region Untested Region 0.1 0.01 0.001 0.01 0 50 100 150 ILOAD (mA) 10 200 0 50 100 150 200 ILOAD (mA) Rev.K.04 AME AME8804 300mA CMOS LDO n External Resistor Divider Table R1 (K Ohm) 1 2 5 10 20 50 100 200 500 1000 R2(K Ohm)=(1.215*R1(K Ohm))/(Vout-1.215) Vout 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 14.29 9.00 6.57 5.17 4.26 3.63 3.16 2.79 2.51 2.27 2.08 1.91 1.77 1.65 1.55 1.46 1.37 1.30 1.23 1.17 1.12 1.07 1.03 0.98 0.95 0.91 0.88 0.85 0.82 0.79 0.77 0.74 0.72 0.70 0.68 0.66 28.59 18.00 13.14 10.34 8.53 7.25 6.31 5.59 5.01 4.54 4.15 3.83 3.55 3.31 3.10 2.91 2.75 2.60 2.47 2.35 2.24 2.14 2.05 1.97 1.89 1.82 1.75 1.69 1.64 1.58 1.53 1.49 1.44 1.40 1.36 1.32 71.47 45.00 32.84 25.85 21.32 18.13 15.78 13.97 12.53 11.36 10.38 9.57 8.87 8.27 7.74 7.28 6.86 6.50 6.17 5.87 5.60 5.35 5.13 4.92 4.73 4.55 4.39 4.23 4.09 3.96 3.83 3.72 3.61 3.50 3.40 3.31 142.94 90.00 65.68 51.70 42.63 36.27 31.56 27.93 25.05 22.71 20.77 19.13 17.74 16.53 15.48 14.55 13.73 12.99 12.34 11.74 11.20 10.70 10.25 9.84 9.46 9.10 8.77 8.47 8.18 7.92 7.67 7.43 7.21 7.00 6.81 6.62 285.88 180.00 131.35 103.40 85.26 72.54 63.12 55.86 50.10 45.42 41.54 38.27 35.47 33.06 30.96 29.10 27.46 25.99 24.67 23.48 22.40 21.41 20.51 19.68 18.91 18.20 17.55 16.93 16.36 15.83 15.33 14.86 14.42 14.01 13.61 13.24 714.71 450.00 328.38 258.51 213.16 181.34 157.79 139.66 125.26 113.55 103.85 95.67 88.69 82.65 77.39 72.75 68.64 64.97 61.68 58.70 55.99 53.52 51.27 49.19 47.28 45.51 43.86 42.33 40.91 39.58 38.33 37.16 36.05 35.01 34.03 33.11 517.02 426.32 362.69 315.58 279.31 250.52 227.10 207.69 191.34 177.37 165.31 154.78 145.51 137.29 129.95 123.35 117.39 111.98 107.05 102.53 98.38 94.55 91.01 87.73 84.67 81.82 79.15 76.66 74.31 72.11 70.03 68.07 66.21 852.63 725.37 631.17 558.62 501.03 454.21 415.38 382.68 354.74 330.61 309.55 291.02 274.58 259.89 246.70 234.78 223.96 214.10 205.06 196.76 189.11 182.02 175.45 169.34 163.64 158.31 153.31 148.62 144.21 140.06 136.13 132.43 826.53 773.89 727.54 686.44 649.73 616.75 586.96 559.91 535.24 512.66 491.90 472.76 455.06 438.63 423.34 409.09 395.77 383.28 371.56 360.53 350.14 340.34 331.06 877.26 846.69 818.18 791.53 766.56 743.12 721.07 700.29 680.67 662.13 3.10 0.64 1.29 3.22 6.45 12.89 32.23 64.46 128.91 322.28 644.56 Rev.K.04 11 AME AME8804 300mA CMOS LDO n External Resistor Divider Table (contd.) R1 (K Ohm) 1 2 5 10 20 50 100 200 500 1000 R2(K Ohm)=(1.215*R1(K Ohm))/(Vout-1.215) Vout 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 0.63 0.61 0.60 0.58 0.57 0.56 0.54 0.53 0.52 0.51 0.50 0.49 0.48 0.47 0.46 0.45 0.44 0.44 0.43 0.42 0.41 0.41 0.40 0.39 0.39 0.38 0.38 0.37 0.36 0.36 0.35 0.35 0.34 0.34 0.33 0.33 0.33 1.26 1.22 1.19 1.17 1.14 1.11 1.09 1.06 1.04 1.02 1.00 0.98 0.96 0.94 0.92 0.91 0.89 0.87 0.86 0.84 0.83 0.81 0.80 0.79 0.78 0.76 0.75 0.74 0.73 0.72 0.71 0.70 0.69 0.68 0.67 0.66 0.65 3.14 3.06 2.99 2.91 2.85 2.78 2.72 2.66 2.60 2.55 2.49 2.44 2.40 2.35 2.31 2.26 2.22 2.18 2.14 2.11 2.07 2.04 2.00 1.97 1.94 1.91 1.88 1.85 1.82 1.79 1.77 1.74 1.72 1.69 1.67 1.65 1.63 6.28 6.12 5.97 5.83 5.69 5.56 5.44 5.32 5.20 5.09 4.99 4.89 4.79 4.70 4.61 4.53 4.44 4.36 4.29 4.21 4.14 4.07 4.00 3.94 3.88 3.81 3.76 3.70 3.64 3.59 3.54 3.49 3.44 3.39 3.34 3.30 3.25 12.56 12.24 11.94 11.65 11.38 11.12 10.87 10.63 10.41 10.19 9.98 9.78 9.59 9.40 9.22 9.05 8.88 8.73 8.57 8.42 8.28 8.14 8.01 7.88 7.75 7.63 7.51 7.40 7.29 7.18 7.07 6.97 6.87 6.78 6.69 6.59 6.51 31.40 30.60 29.85 29.14 28.45 27.80 27.18 26.59 26.02 25.47 24.95 24.45 23.96 23.50 23.06 22.63 22.21 21.81 21.43 21.06 20.70 20.35 20.02 19.69 19.38 19.07 18.78 18.49 18.22 17.95 17.69 17.43 17.19 16.95 16.71 16.49 16.27 62.79 61.21 59.71 58.27 56.91 55.61 54.36 53.17 52.03 50.94 49.90 48.89 47.93 47.00 46.11 45.25 44.42 43.63 42.86 42.11 41.40 40.70 40.03 39.38 38.76 38.15 37.56 36.99 36.43 35.89 35.37 34.86 34.37 33.89 33.43 32.97 32.53 125.58 122.42 119.41 116.55 113.82 111.21 108.72 106.35 104.07 101.89 99.79 97.79 95.86 94.00 92.22 90.50 88.85 87.25 85.71 84.23 82.79 81.41 80.07 78.77 77.51 76.30 75.12 73.97 72.86 71.79 70.74 69.73 68.74 67.78 66.85 65.94 65.06 313.95 306.05 298.53 291.37 284.54 278.03 271.81 265.86 260.17 254.72 249.49 244.47 239.64 235.01 230.55 226.26 222.12 218.13 214.29 210.57 206.98 203.52 200.16 196.92 193.78 190.74 187.79 184.93 182.16 179.47 176.86 174.32 171.85 169.46 167.13 164.86 162.65 627.91 612.09 597.05 582.73 569.09 556.06 543.62 531.73 520.34 509.43 498.97 488.93 479.29 470.02 461.10 452.51 444.24 436.27 428.57 421.14 413.97 407.04 400.33 393.84 387.56 381.48 375.58 369.86 364.32 358.94 353.71 348.64 343.71 338.91 334.25 329.72 325.30 5.00 0.32 0.64 1.61 3.21 6.42 16.05 32.10 64.20 160.50 321.00 Note: Small load (greater than 2 mA) is necessary as R1 or R2 is larger than 50 Kohm. Otherwise, output voltage probably cannot be pulled down to 0 V on disable mode. 12 Rev.K.04 AME AME8804 300mA CMOS LDO n Date Code Rule Marking Date Code Year A A A W W xxx0 A A A W W xxx1 A A A W W xxx2 A A A W W xxx3 A A A W W xxx4 A A A W W xxx5 A A A W W xxx6 A A A W W xxx7 A A A W W xxx8 A A A W W xxx9 n Tape and Reel Dimension SOT-25 P W AME AME PIN 1 Carrier Tape, Number of Components Per Reel and Reel Size Rev.K.04 Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size SOT-25 8.0±0.1 mm 4.0±0.1 mm 3000pcs 180±1 mm 13 AME AME8804 300mA CMOS LDO n Tape and Reel Dimension TSOT-25 P W AME AME PIN 1 Carrier Tape, Number of Components Per Reel and Reel Size Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size TSOT-25 8.0±0.1 mm 4.0±0.1 mm 3000pcs 180±1 mm SOT-26 P W AME AME PIN 1 Carrier Tape, Number of Components Per Reel and Reel Size 14 Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size SOT-26 8.0±0.1 mm 4.0±0.1 mm 3000pcs 180±1 mm Rev.K.04 AME AME8804 300mA CMOS LDO n Tape and Reel Dimension TSOT-26 P W AME AME PIN 1 Carrier Tape, Number of Components Per Reel and Reel Size Rev.K.04 Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size TSOT-26 8.0±0.1 mm 4.0±0.1 mm 3000pcs 180±1 mm 15 AME AME8804 300mA CMOS LDO n Package Dimension SOT-25 Top View Side View D θ1 SYMBOLS MILLIMETERS MIN 1.20REF E H A PIN 1 L S1 0.0472REF 0.15 0.0000 0.0059 b 0.30 0.55 0.0118 0.0217 D 2.70 3.10 0.1063 0.1220 E 1.40 1.80 0.0551 0.0709 1.90 BSC 2.60 θ1 0.07480 BSC 3.00 0.37BSC L A MAX 0.00 H Front View MIN A1 e e MAX INCHES 0o 0.10236 0.11811 0.0146BSC 10o 0o 10o 0.95BSC 0.0374BSC MILLIMETERS INCHES A1 S1 b SOT-26 Top View Side View D e θ1 SYMBOLS MIN 1.20REF E H A L PIN 1 0.0000 0.0059 b 0.30 0.55 0.0118 0.0217 D 2.70 3.10 0.1063 0.1220 E 1.40 1.80 0.0551 0.0709 θ1 1.90 BSC 2.60 S1 0.0748 BSC 3.00 0.37REF 0 o 10 0.95REF 0.10236 0.11811 0.0146REF o 0 o 10 o 0.0374REF A1 A 16 0.0472REF 0.15 L b MAX 0.00 H Front View MIN A1 e S1 MAX Rev.K.04 AME AME8804 300mA CMOS LDO n Package Dimension TSOT-25 Top View Side View D H E θ1 PIN 1 L S1 SYMBOLS MAX MIN MAX A+A1 0.90 1.25 0.0354 0.0492 b 0.30 0.50 0.0118 0.0197 D 2.70 3.10 0.1063 0.1220 E 1.40 1.80 0.0551 0.0709 e L 1 Front View INCHES MIN H e MILLIMETERS 2.40 3.00 0.35BSC 0o 10o 0.07480 BSC 0.09449 0.11811 0.0138BSC 0o 10o 0.95BSC 0.0374BSC MILLIMETERS INCHES A1 A S1 1.90 BSC b TSOT-26 Top View Side View θ1 E H D e L PIN 1 SYMBOLS MIN MAX MIN MAX A+A1 0.90 1.25 0.0354 0.0492 b 0.30 0.50 0.0118 0.0197 D 2.70 3.10 0.1063 0.1220 E 1.40 1.80 0.0551 0.0709 e H S1 L ◊1 Front View 2.40 3.00 0.35BSC 0o 10o 0.95BSC 0.07480 BSC 0.09449 0.11811 0.0138BSC 0o 10o 0.0374BSC b Rev.K.04 A1 A S1 1.90 BSC 17 www.ame.com.tw E-Mail: [email protected] Life Support Policy: These products of AME, Inc. are not authorized for use as critical components in life-support devices or systems, without the express written approval of the president of AME, Inc. AME, Inc. reserves the right to make changes in the circuitry and specifications of its devices and advises its customers to obtain the latest version of relevant information. AME, Inc. , January 2012 Document: 2006/2095-DS8804-K.04 Corporate Headquarter AME, Inc. 8F, 12, WenHu St., Nei Hu Taipei, Taiwan. 114 Tel: 886 2 2627-8687 Fax: 886 2 2659-2989