Intersil LP3991TL-2.5 300ma linear voltage regulator for digital application Datasheet

LP3991
300mA Linear Voltage Regulator for Digital Applications
General Description
Features
Operating from a minimum input voltage of 1.65V, the LP3991
regulator has been designed to provide fixed stable output
voltages for load currents up to 300mA. This device is suitable
where accurate, low voltages are required from low input voltage sources and is therefore suitable for post regulation of
switched mode regulators. In such applications, significant
improvements in performance and EMI can be realized, with
little reduction in overall efficiency. The LP3991 will provide
fixed outputs as low as 1.2V from a wide input range of 1.65V
to 4.0V Using the enable pin, the device may be controlled to
provide a shutdown state, in which negligible supply current
is drawn.
The LP3991 is designed to be stable with space saving ceramic capacitors as small as 0402 case size.
Performance is specified for a -40°C to 125°C junction temperature range.
For output voltage options please contact your local NSC
sales office.
■
■
■
■
■
■
■
■
■
■
Operation from 1.65V to 4.0V Input
1% accuracy at room temperature
Output Voltage from 1.2V to 2.8V
125mV Dropout at 300mA load
50µA Quiescent Current at 1mA Load
Inrush Current controlled to 600mA
PSRR 65dB at 1kHz
100µs Start-Up time for 1.5V VOUT
Stable with Ceramic Capacitors as small as 0402
Thermal-Overload and Short-Circuit Protection
Package
4 pin micro SMD (0.963mm x 1.446mm)
For other package options contact your NSC sales office.
Applications
■ Post DC/DC Regulator
■ Battery Operated Devices
■ Hand-Held Information Appliances
Typical Application Circuit
20110002
© 2007 National Semiconductor Corporation
201100
www.national.com
LP3991 300mA Linear Voltage Regulator for Digital Applications
December 13, 2007
LP3991
Pin Descriptions
Packages
Pin No.
Symbol
Name and Function
B1
VOUT
Voltage output. A Low ESR Ceramic Capacitor should be
connected from this pin to GND. (See Application Information)
Connect this output to the load circuit.
A1
GND
Common Ground. Connect to Pad.
A2
VEN
Enable Input; Enables the Regulator when ≥ 0.95V.
Disables the Regulator when ≤ 0.4V.
Enable Input has an internal 1.2MΩ pull-down resistor to GND.
B2
VIN
Voltage Supply Input. A 1.0µF capacitor should be connected
from this pin to GND.
Connection Diagram
4 Bump Thin Micro SMD, Large Bump
20110006
See NS package number TLA04
Ordering Information (4-Bump Micro SMD)
Only available as Lead Free.
Output Voltage (V)
Grade
LP3991 Supplied as 1000 Units, Tape
and Reel
LP3991 Supplied as 3000 Units, Tape
and Reel
0.8
STD
LP3991TL-0.8
LP3991TLX-0.8
1.2
STD
LP3991TL-1.2
LP3991TLX-1.2
1.3
STD
LP3991TL-1.3
LP3991TLX-1.3
1.5
STD
LP3991TL-1.5
LP3991TLX-1.5
1.8
STD
LP3991TL-1.8
LP3991TLX-1.8
2.0
STD
LP3991TL-2.0
LP3991TLX-2.0
2.5
STD
LP3991TL-2.5
LP3991TLX-2.5
2.8
STD
LP3991TL-2.8
LP3991TLX-2.8
3.0
STD
LP3991TL-3.0
LP3991TLX-3.0
www.national.com
2
LP3991
Absolute Maximum Ratings
(Notes 1, 2)
Operating Ratings
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
(Note 1)
Input Voltage Range
Recommended Load Current
Junction Temperature
Ambient Temperature TARange
(Note 6)
VIN, VOUT, Pins: Voltage to GND
-0.3 to 6.5V
VEN Pin: Voltage to GND
-0.3 to (VIN + 0.3V) to 6.5V
(max)
Junction Temperature
150°C
Lead/Pad Temp. (Note 3)
Micro SMD
260°C
Storage Temperature
-65 to 150°C
Continuous Power Dissipation
Internally Limited
(Note 4)
ESD (Note 5)
Human Body Model
2KV
Machine Model
200V
Thermal Properties
1.65 to 4.0V
300mA
-40°C to 125°C
-40°C to 85°C
(Note 1)
Junction To Ambient Thermal
Resistance(Note 7)
θJA JEDEC Board
(Note 8)
88°C/W
θJA 4 Layer Board
160°C/W
Electrical Characteristics
Unless otherwise noted, VEN =950mV, VIN = VOUT + 0.5V, or 1.8V, whichever is higher. CIN = 1µF, IOUT = 1.0mA, COUT =4.7µF.
Typical values and limits appearing in normal type apply for TA = 25°C. Limits appearing in boldface type apply over the full junction
temperature range for operation, −40 to +125°C. (Note 9)
Symbol
VIN
ΔVOUT
Parameter
Input Voltage
Conditions
Typ
(Note 10)
Limit
Min
Max
1.65
3.6
(Note 16)
Output Voltage Tolerance
4.0
VIN = VIN(NOM) to 3.6V
ILOAD = 1 to 300mA
VIN = VOUT(NOM) +0.5V to 3.6V,
IOUT = 1mA
V
-1.0
-3.0
1.0
3.0
-2.5
2.5
%
0.05
1
%/V
10
60
µV/mA
Temperature
(TJ)=
-25°C to +85°C
Line Regulation Error
Units
0.8V ≤ VOUT ≤ 2.8V
VDO
Load Regulation Error
IOUT = 1mA to 300mA
Dropout Voltage(Note 11)
1.8 ≤ VOUT ≤ 2.5V
VOUT > 2.5V
IOUT = 150mA
55
90
IOUT = 300mA
110
180
IOUT = 150mA
40
80
IOUT = 300mA
75
160
ILOAD
Minimum Load Current
(Note 12)
IQ
Quiescent Current
VEN = 950mV, IOUT = 0mA
0
VEN = 950mV, IOUT = 300mA
VEN = 0.4V
ISC
Short Circuit Current Limit
IOUT
Maximum Output Current
PSRR
Power Supply Rejection Ratio
(Note 14)
en
TSHUTDOWN
VIN = 3.6V (Note 13)
100
120
225
0.001
1.0
900
300
f = 1kHz, IOUT = 1mA to 300mA
65
Output noise Voltage (Note 14)
BW = 10Hz to 100kHz,
VIN = 4.2V, COUT = 4.7µF
280
Thermal Shutdown
Temperature
160
Hysteresis
20
3
mA
50
550
mV
µA
mA
mA
dB
µVRMS
°C
www.national.com
LP3991
Electrical Characteristics con't.
Unless otherwise noted, VEN =950mV, VIN = VOUT + 0.5V, or 1.8V, whichever is higher. CIN = 1µF, IOUT = 1.0mA, COUT =4.7µF.
Typical values and limits appearing in normal type apply for TA = 25°C. Limits appearing in boldface type apply over the full junction
temperature range for operation, −40 to +125°C. (Note 9)
Symbol
Parameter
Conditions
Typ
Limit
Min
Max
Units
Enable Control Characteristics
IEN
(Note 15)
Maximum Input Current at
VEN Input
VEN = 0V, VIN = 3.6V
VIL
Low Input Threshold
VIN = 1.65V to 3.6V
VIH
High Input Threshold
VIN = 1.65V to 3.6V
VEN = VIN = 3.6V
0.001
3
µA
5.5
V
0.4
V
0.95
Timing Characteristics
TON
Turn On Time (Note 14)
To 95% Level
VIN(MIN) to 3.6V
VOUT ≤ 2.0V
100
VOUT > 2.0V
140
Line Transient Response |δVOUT| Trise = Tfall = 30µs (Note 14)
δVIN = 600mV
Transient
Response
IIR
140
IOUT = 300mA to 1mA
80
IOUT = 0mA to 200mA
110
IOUT = 1mA to 200mA
80
110
IOUT = 200mA to 1mA
60
IOUT = 0mA to 150mA
100
IOUT = 1mA to 150mA
70
IOUT = 150mA to 1mA
50
In-Rush Current (Note 14)
mV
(pk - pk)
6
Load Transient Response |δVOUT| Trise = Tfall = 1µs IOUT = 0 mA to 300mA
(Note 14)
IOUT = 1mA to 300mA
Overshoot on Start-up
µs
mV
0
2
%
600
1000
mA
Note 1: Absolute Maximum Ratings are limits beyond which damage can occur. Operating Ratings are conditions under which operation of the device is
guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical
Characteristics tables.
Note 2: All Voltages are with respect to the potential at the GND pin.
Note 3: For further information on these packages please refer to the following application notes,AN-1112 Micro SMD Wafer Level Chip Scale Package.
Note 4: Internal thermal shutdown circuitry protects the device from permanent damage.
Note 5: The human body model is 100pF discharged through a 1.5kΩ resistor into each pin. The machine model is a 200pF capacitor discharged directly into
each pin.
Note 6: The maximum ambient temperature (TA(max)) is dependant on the maximum operating junction temperature (TJ(max-op) = 125°C), the maximum power
dissipation of the device in the application (PD(max)), and the junction to ambient thermal resistance of the part / package in the application (θJA), as given by the
following equation: TA(max) = TJ(max-op) - (θJA × PD(max)).
Note 7: Junction to ambient thermal resistance is dependant on the application and board layout. In applications where high maximum power dissipation is
possible, special care must be paid to thermal dissipation issues in board design.
Note 8: Full details can be found in JESD61-7
Note 9: All limits are guaranteed. All electrical characteristics having room-temperature limits are tested during production at TJ = 25°C or correlated using
Statistical Quality Control methods. Operation over the temperature specification is guaranteed by correlating the electrical characteristics to process and
temperature variations and applying statistical process control.
Note 10: VIN(MIN) = VOUT(NOM) + 0.5V or 1.65V, whichever is greater. (See post DC/DC convertor example in application information section).
Note 11: Dropout voltage is voltage difference between input and output at which the output voltage drops to 100mV below its nominal value. This parameter is
only specified for output voltages above 1.8V.
Note 12: The device maintains the regulated output voltage without a load.
Note 13: Short circuit current is measured with VOUT pulled to 0V.
Note 14: This electrical specification is guaranteed by design.
Note 15: Enable Pin has an internal 1.2MΩ typical, resistor connected to GND.
Note 16: The device will operate with input voltages up to 4.0V. However special care should be taken in relation to thermal dissipation and the need to derate
the maximum allowable ambient temperature. See (Notes 6, 7)
www.national.com
4
LP3991
Output Capacitor, Recommended Specifications
Parameter
COUT
Output Capacitor
Conditions
Capacitance
(Note 17)
ESR
Typ
Limit
Min
VOUT ≥ 1.5V
4.7
2
VOUT < 1.5V
(Note 18)
2.2
1.6
5
Max
Units
µF
500
mΩ
Note 17: The capacitor tolerance should be 30% or better over temperature. The full operating conditions for the application should be considered when selecting
a suitable capacitor to ensure that the minimum value of capacitance is always met. Recommended capacitor type is X7R or X5R. (See capacitor section in
Applications Hints)
Note 18: On lower voltage options, 2.2µF output capacitor may be used but some degradation in load transient (10 -15%) can be expected, compared to a 4.7µF.
5
www.national.com
LP3991
Typical Performance Characteristics.
Unless otherwise specified, CIN = 1.0µF Ceramic, COUT = 4.7µF
Ceramic, VIN = VOUT(NOM) + 0.5V or 1.8V whichever is greater, TA = 25°C, VOUT(NOM) = 1.5V , Shutdown pin is tied to VIN.
Output Voltage Change vs Temperature
Output Voltage vs Minimum Input Voltage
20110010
20110009
Ground Current vs Load Current
Ground Current vs VIN. ILOAD = 1mA
20110011
20110012
Dropout Voltage
Dropout Voltage vs Output Voltage
20110015
20110014
www.national.com
6
Unless otherwise specified, CIN = 1.0µF Ceramic,
COUT = 4.7µF Ceramic, VIN = VOUT(NOM) + 0.5V or 1.8V whichever is greater, TA = 25°C, VOUT(NOM) = 1.5V , Shutdown pin is tied
to VIN.
Load Transient, VOUT = 1.5V
Load Transient, VOUT = 1.2V
20110018
20110021
Line Transient, ILOAD = 1mA
Line Transient, ILOAD = 300mA
20110019
20110020
Enable Characteristics
Short Circuit Current
20110022
20110023
7
www.national.com
LP3991
Typical Performance Characteristics con't.
LP3991
Typical Performance Characteristics con't.
Unless otherwise specified, CIN = 1.0µF Ceramic,
COUT = 4.7µF Ceramic, VIN = VOUT(NOM) + 0.5V or 1.8V whichever is greater, TA = 25°C, VOUT(NOM) = 1.5V , Shutdown pin is tied
to VIN.
Power Supply Rejection Ratio
Power Supply Rejection Ratio
20110025
20110026
Noise Density
20110028
www.national.com
8
EXTERNAL CAPACITORS
In common with most regulators, the LP3991 requires external capacitors for regulator stability. The LP3991 is specifically designed for portable applications requiring minimum
board space and smallest components. These capacitors
must be correctly selected for good performance.
INPUT CAPACITOR
An input capacitor is required for stability. It is recommended
that a 1.0µF capacitor be connected between the LP3991 input pin and ground (this capacitance value may be increased
without limit).
This capacitor must be located a distance of not more than
1cm from the input pin and returned to a clean analogue
ground. Any good quality ceramic, tantalum, or film capacitor
may be used at the input.
Important: Tantalum capacitors can suffer catastrophic failures due to surge current when connected to a lowimpedance source of power (like a battery or a very large
capacitor). If a tantalum capacitor is used at the input, it must
be guaranteed by the manufacturer to have a surge current
rating sufficient for the application.
There are no requirements for the ESR (Equivalent Series
Resistance) on the input capacitor, but tolerance, temperature, and voltage coefficients must be considered when selecting the capacitor to ensure the capacitance will remain ≊
1.0µF over the entire operating temperature range.
OUTPUT CAPACITOR
Correct selection of the output capacitor is critical to ensure
stable operation in the intended application.
The output capacitor must meet all the requirements specified
in the recommended capacitor table over all conditions in the
application. these conditions include DC bias, frequency and
temperature. Unstable operation will result if the capacitance
drops below the minimum specified value.
The LP3991 is designed specifically to work with very small
ceramic output capacitors. For voltage options of 1.5V and
higher, A 4.7µF ceramic capacitor (dielectric type X7R or
X5R) with an ESR between 5mΩ to 500mΩ, is suitable in the
LP3991 application circuit. However, on lower VOUT options a
2.2µF may be employed with only a small increase in load
transient.
Other ceramic types such as Y5V and Z5U are less suitable
owing to their inferior temperature characteristics. (See section on Capacitor Characteristics).
It is also recommended that the output capacitor is placed
within 1cm of the output pin and returned to a clean, low
impedance, ground connection.
It is possible to use tantalum or film capacitors at the device
output, VOUT, but these are not as attractive for reasons of
size and cost (see the section Capacitor Characteristics).
20110040
FIGURE 1. Effect of DC bias on Capacitance Value.
As an example Figure 1 shows a typical graph showing a
comparison of capacitor case sizes in a Capacitance vs. DC
Bias plot. As shown in the graph, as a result of the DC Bias
condition, the capacitance value may drop below the minimum capacitance value given in the recommended capacitor
table. Note that the graph shows the capacitance out of spec
for the 0402 case size capacitor at higher bias voltages. It is
therefore recommended that the capacitor manufacturers'
specifications for the nominal value capacitor are consulted
for all conditions as some capacitor sizes (e.g. 0402) may not
be suitable in the actual application. Ceramic capacitors have
the lowest ESR values, thus making them best for eliminating
high frequency noise. The ESR of a typical 4.7µF ceramic
capacitor is in the range of 20mΩ to 40mΩ, which easily
meets the ESR requirement for stability for the LP3991. The
temperature performance of ceramic capacitors varies by
type. Capacitor type X7R is specified with a tolerance of ±15%
over the temperature range -55°C to +125°C. The X5R has a
similar tolerance over the reduced temperature range of -55°
C to +85°C. Some large value ceramic capacitors (4.7µF) are
manufactured with Z5U or Y5V temperature characteristics,
which can result in the capacitance dropping by more than
50% as the temperature varies from 25°C to 85°C. Therefore
X7R or X5R types are recommended in applications where
the temperature will change significantly above or below 25°
C.
Tantalum capacitors are less desirable than ceramic for use
as output capacitors because they are more expensive when
comparing equivalent capacitance and voltage ratings in the
NO-LOAD STABILITY
The LP3991 will remain stable and in regulation with no external load. This is an important consideration in some circuits, for example CMOS RAM keep-alive applications.
CAPACITOR CHARACTERISTICS
The LP3991 is designed to work with ceramic capacitors on
the input and output to take advantage of the benefits they
offer. For capacitance values around 4.7µF, ceramic capaci-
9
www.national.com
LP3991
tors give the circuit designer the best design options in terms
of low cost and minimal area.
For both input and output capacitors, careful interpretation of
the capacitor specification is required to ensure correct device
operation. The capacitor value can change greatly dependant
on the conditions of operation and capacitor type.
In particular, to ensure stability, the output capacitor selection
should take account of all the capacitor parameters, to ensure
that the specification is met within the application. Capacitance value can vary with DC bias conditions as well as
temperature and frequency of operation. Capacitor values will
also show some decrease over time due to aging. The capacitor parameters are also dependant on the particular case
size with smaller sizes giving poorer performance figures in
general.
Application Information
LP3991
1µF to 4.7µF range. Another important consideration is that
tantalum capacitors have higher ESR values than equivalent
size ceramics. This means that while it may be possible to find
a tantalum capacitor with an ESR value within the stable
range, it would have to be larger in capacitance (which means
bigger and more costly) than a ceramic capacitor with the
same ESR value. It should also be noted that the ESR of a
typical tantalum will increase about 2:1 as the temperature
goes from 25°C down to -40°C, so some guard band must be
allowed.
micro SMD MOUNTING
The micro SMD package requires specific mounting techniques which are detailed in the National Semiconductor
Application Note (AN-1112). Referring to the section Surface
Mount Technology (SMT) Assenbly Considerations, it should
be noted that the pad style which must be used with the 4 pin
package is NSMD (non-solder mask defined) type.
For best results during assembly, alignment ordinals on the
PCB may be used to facilitate placement of the micro SMD
device.
ENABLE CONTROL
The LP3991 features an active high Enable pin, VEN, which
turns the device on when pulled high. When not enabled the
regulator output is off and the device typically consumes 2nA.
If the application does not require the Enable switching feature, the VEN pin should be tied to VIN to keep the regulator
output permanently on.
To ensure proper operation, the signal source used to drive
the VEN input must be able to swing above and below the
specified turn-on/off voltage thresholds listed in the Electrical
Characteristics section under VIL and VIH.
micro SMD LIGHT SENSITIVITY
Exposing the micro SMD device to direct sunlight may cause
mis-operation of the device. Light sources such as halogen
lamps can affect the electrical performance if brought near to
the device.
The wavelengths which have most detrimental effect are reds
and infra-reds, which means that fluorescent lighting, used
inside most buildings will have little effect on performance.
20110036
FIGURE 2. LP3991 Used as a Post DC/DC regulator
POST-BUCK REGULATOR
Linear Post-Regulation can be an effective way to reduce ripple and switching noise from DC/DC convertors while still
maintaining a reasonably high overall efficiency.
The LP3991 is particularly suitable for this role due to its low
input voltage requirements. In addition, there is often no need
for a separate input capacitor for the LP3991 as it can share
the output cap of the DC/DC convertor.
Care of PCB layouts involving switching regulators is
paramount. In particular, the ground paths for the LDO should
be routed separately from the switcher ground and star connected close to the battery. Routing of the switch pin of the
DC/DC convertor must be kept short to minimize radiated
EMI. A low pass filter such as a ferrite bead or common mode
choke on the battery input leads can further reduce radiated
EMI.
Figure 2 shows a typical example using an LM3673, 350mA
DC/DC buck regulator with a nominal output of 1.8V and a
1.5V LP3991. The overall efficiency will be greater than 70%
over the full Li-Ion battery voltage range. Maximum efficiency
is achieved by minimizing the difference between VIN and
VOUT of the LP3991. The LP3991-1.5 will remain in regulation
down to an input voltage of 1.65V, so, in this case, a 1.8V
buck with 5% tolerance is adequate for all conditions of temperature and load.
www.national.com
MAXIMUM SUPPLY VOLTAGE AND THERMAL
CONSIDERATIONS
Maximum recommended input voltage is 3.6V. The device
may be operated at 4.0V VIN if proper care is given to the
board design in regard to thermal dissipation. As a guide
please refer to the following table for ambient temperature at
2 input voltages and 2 load currents for the example board
types.
θJA
VIN
VOUT
IOUT
PD
Ambient
Temp.
88ºC/W
3.6V
2.8V
160mA
0.130W
113ºC
250mA
0.200W
107ºC
4.0V
2.8V
160mA
0.190W
108ºC
250mA
0.300W
98ºC
160mA
0.130W
104ºC
250mA
0.200W
93ºC
160mA
0.190W
94ºC
250mA
0.300W
77ºC
160ºC/W
3.6V
4.0V
10
2.8V
2.8V
LP3991
Physical Dimensions inches (millimeters) unless otherwise noted
4 Bump Thin micro SMD, Large Bump
NS Package Number TLA04ZTA
The Dimensions for X1, X2 and X3 as given as:
X1 = 0.963mm ± 0.030mm
X2 = 1.446mm ± 0.03mm
X3 = 0.60mm ± 0.075mm
11
www.national.com
LP3991 300mA Linear Voltage Regulator for Digital Applications
Notes
For more National Semiconductor product information and proven design tools, visit the following Web sites at:
Products
Design Support
Amplifiers
www.national.com/amplifiers
WEBENCH
www.national.com/webench
Audio
www.national.com/audio
Analog University
www.national.com/AU
Clock Conditioners
www.national.com/timing
App Notes
www.national.com/appnotes
Data Converters
www.national.com/adc
Distributors
www.national.com/contacts
Displays
www.national.com/displays
Green Compliance
www.national.com/quality/green
Ethernet
www.national.com/ethernet
Packaging
www.national.com/packaging
Interface
www.national.com/interface
Quality and Reliability
www.national.com/quality
LVDS
www.national.com/lvds
Reference Designs
www.national.com/refdesigns
Power Management
www.national.com/power
Feedback
www.national.com/feedback
Switching Regulators
www.national.com/switchers
LDOs
www.national.com/ldo
LED Lighting
www.national.com/led
PowerWise
www.national.com/powerwise
Serial Digital Interface (SDI)
www.national.com/sdi
Temperature Sensors
www.national.com/tempsensors
Wireless (PLL/VCO)
www.national.com/wireless
THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION
(“NATIONAL”) PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY
OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO
SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS,
IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS
DOCUMENT.
TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT
NATIONAL’S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL
PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR
APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND
APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE
NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS.
EXCEPT AS PROVIDED IN NATIONAL’S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO
LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE
AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY
RIGHT.
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR
SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and
whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected
to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform
can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other
brand or product names may be trademarks or registered trademarks of their respective holders.
Copyright© 2007 National Semiconductor Corporation
For the most current product information visit us at www.national.com
National Semiconductor
Americas Customer
Support Center
Email:
[email protected]
Tel: 1-800-272-9959
www.national.com
National Semiconductor Europe
Customer Support Center
Fax: +49 (0) 180-530-85-86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +49 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
National Semiconductor Asia
Pacific Customer Support Center
Email: [email protected]
National Semiconductor Japan
Customer Support Center
Fax: 81-3-5639-7507
Email: [email protected]
Tel: 81-3-5639-7560
Similar pages