[ /Title (CD74 HC123 , CD74 HCT12 3, CD74 HC423 , CD74 HCT42 3) /Subject (High Speed Data sheet acquired from Harris Semiconductor SCHS142 September 1997 CD74HC123, CD74HCT123, CD74HC423, CD74HCT423 High Speed CMOS Logic Dual Retriggerable Monostable Multivibrators with Resets Features Description • Overriding Reset Terminates Output Pulse The Harris CD74HC123, CD74HCT123, CD74HC423 and CD74HCT423 are dual monostable multivibrators with resets. They are all retriggerable and differ only in that the 123 types can be triggered by a negative to positive reset pulse; whereas the 423 types do not have this feature. An external resistor (RX) and an external capacitor (CX) control the timing and the accuracy for the circuit. Adjustment of Rx and CX provides a wide range of output pulse widths from the Q and Q terminals. Pulse triggering on the A and B inputs occur at a particular voltage level and is not related to the rise and fall times of the trigger pulses. • Triggering From the Leading or Trailing Edge • Q and Q Buffered Outputs • Separate Resets • Wide Range of Output-Pulse Widths • Schmitt Trigger on Both A and B Inputs • Fanout (Over Temperature Range) - Standard Outputs . . . . . . . . . . . . . . . 10 LSTTL Loads - Bus Driver Outputs . . . . . . . . . . . . . 15 LSTTL Loads Once triggered, the output pulse width may be extended by retriggering inputs A and B. The output pulse can be terminated by a LOW level on the Reset (R) pin. Trailing edge triggering (A) and leading edge triggering (B) inputs are provided for triggering from either edge of the input pulse. If either Mono is not used each input on the unused device (A, B, and R) must be terminated high or low. • Wide Operating Temperature Range . . . -55oC to 125oC • Balanced Propagation Delay and Transition Times • Significant Power Reduction Compared to LSTTL Logic ICs • HC Types - 2V to 6V Operation - High Noise Immunity: NIL = 30%, NIH = 30%of VCC at VCC = 5V The minimum value of external resistance, Rx is typically 5kΩ. The minimum value external capacitance, CX, is 0pF. The calculation for the pulse width is tW = 0.45 RXCX at VCC = 5V. Ordering Information • HCT Types - 4.5V to 5.5V Operation - Direct LSTTL Input Logic Compatibility, VIL= 0.8V (Max), VIH = 2V (Min) - CMOS Input Compatibility, Il ≤ 1µA at VOL, VOH PART NUMBER Pinout CD74HC123, CD74HCT123, CD74HC423, CD74HCT423 (PDIP, SOIC) TOP VIEW TEMP. RANGE (oC) CD74HC123E -55 to 125 16 Ld PDIP E16.3 CD74HCT123E -55 to 125 16 Ld PDIP E16.3 CD74HC423E -55 to 125 16 Ld PDIP E16.3 CD74HCT423E -55 to 125 16 Ld PDIP E16.3 CD74HC123M -55 to 125 16 Ld SOIC M16.15 CD74HCT123M -55 to 125 16 Ld SOIC M16.15 1A 1 16 VCC 1B 2 15 1RXCX CD74HC423M -55 to 125 16 Ld SOIC M16.15 1R 3 14 1CX CD74HCT423M -55 to 125 16 Ld SOIC M16.15 1Q 4 13 1Q 2Q 5 12 2Q 2CX 6 11 2R 2RXCX 7 10 2B GND 8 9 2A NOTES: 1. When ordering, use the entire part number. Add the suffix 96 to obtain the variant in the tape and reel. 2. Wafer or die for this part number is available which meets all electrical specifications. Please contact your local sales office or Harris customer service for ordering information. CAUTION: These devices are sensitive to electrostatic discharge. Users should follow proper IC Handling Procedures. Copyright PKG. NO. PACKAGE © Harris Corporation 1997 1 File Number 1708.1 CD74HC123, CD74HCT123, CD74HC423, CD74HCT423 Functional Diagram 1Cx 14 1Rx VCC 15 1Cx 1RxCx 13 1A 1Q 1 MONO 1 4 1B 1Q 2 1R 2R 3 11 5 9 2Q 2A MONO 2 10 12 2B 2Q 2Cx 2RxCx 6 7 2Cx VCC 2Rx TRUTH TABLE INPUTS A OUTPUTS B R Q Q H X H L H X L H L H L ↑ H ↓ H H X X L L H L H ↑ H X H L H X L H L H L ↑ H ↓ H H X X L L H CD74HC/HCT123 CD74HC/HCT423 NOTE: H = High Voltage Level, L = Low Voltage Level, X = Don’t Care. 2 CD74HC123, CD74HCT123, CD74HC423, CD74HCT423 Absolute Maximum Ratings Thermal Information DC Supply Voltage, VCC . . . . . . . . . . . . . . . . . . . . . . . . -0.5V to 7V DC Input Diode Current, IIK For VI < -0.5V or VI > VCC + 0.5V . . . . . . . . . . . . . . . . . . . . . .±20mA DC Output Diode Current, IOK For VO < -0.5V or VO > VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±20mA DC Output Source or Sink Current per Output Pin, IO For VO > -0.5V or VO < VCC + 0.5V . . . . . . . . . . . . . . . . . . . .±25mA DC VCC or Ground Current, ICC or IGND . . . . . . . . . . . . . . . . . .±50mA Thermal Resistance (Typical, Note 3) θJA (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90 SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . .-65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range (TA) . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC Supply Voltage Range, VCC HC Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2V to 6V HCT Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.5V to 5.5V DC Input or Output Voltage, VI, VO . . . . . . . . . . . . . . . . . 0V to VCC Input Rise and Fall Time 2V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1000ns (Max) 4.5V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500ns (Max) 6V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400ns (Max) CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTE: 3. θJA is measured with the component mounted on an evaluation PC board in free air. DC Electrical Specifications TEST CONDITIONS PARAMETER 25oC -40oC TO 85oC -55oC TO 125oC SYMBOL VI (V) IO (mA) VCC (V) VIH - - 2 1.5 - - 1.5 4.5 3.15 - - 3.15 - 3.15 - V 6 4.2 - - 4.2 - 4.2 - V MIN TYP MAX MIN MAX MIN MAX UNITS - 1.5 - V HC TYPES High Level Input Voltage Low Level Input Voltage High Level Output Voltage CMOS Loads VIL VOH - VIH or VIL High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current - 2 - - 0.5 - 0.5 - 0.5 V 4.5 - - 1.35 - 1.35 - 1.35 V 6 - - 1.8 - 1.8 - 1.8 V -0.02 2 1.9 - - 1.9 - 1.9 - V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -0.02 6 5.9 - - 5.9 - 5.9 - V - - - - - - - - - V -4 4.5 3.98 - - 3.84 - 3.7 - V -5.2 6 5.48 - - 5.34 - 5.2 - V 0.02 2 - - 0.1 - 0.1 - 0.1 V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 0.02 6 - - 0.1 - 0.1 - 0.1 V - - - - - - - - - V 4 4.5 - - 0.26 - 0.33 - 0.4 V 5.2 6 - - 0.26 - 0.33 - 0.4 V II VCC or GND - 6 - - ±0.1 - ±1 - ±1 µA ICC VCC or GND 0 6 - - 8 - 80 - 160 µA 3 CD74HC123, CD74HCT123, CD74HC423, CD74HCT423 DC Electrical Specifications (Continued) TEST CONDITIONS SYMBOL VI (V) IO (mA) High Level Input Voltage VIH - - Low Level Input Voltage VIL - High Level Output Voltage CMOS Loads VOH VIH or VIL PARAMETER VCC (V) 25oC -40oC TO 85oC -55oC TO 125oC MIN TYP MAX MIN MAX MIN MAX UNITS 4.5 to 5.5 2 - - 2 - 2 - V - 4.5 to 5.5 - - 0.8 - 0.8 - 0.8 V -0.02 4.5 4.4 - - 4.4 - 4.4 - V -4 4.5 3.98 - - 3.84 - 3.7 - V 0.02 4.5 - - 0.1 - 0.1 - 0.1 V 4 4.5 - - 0.26 - 0.33 - 0.4 V ±0.1 - ±1 - ±1 µA HCT TYPES High Level Output Voltage TTL Loads Low Level Output Voltage CMOS Loads VOL VIH or VIL Low Level Output Voltage TTL Loads Input Leakage Current Quiescent Device Current Additional Quiescent Device Current Per Input Pin: 1 Unit Load II VCC and GND 0 5.5 - ICC VCC or GND 0 5.5 - - 8 - 80 - 160 µA ∆ICC VCC -2.1 - 4.5 to 5.5 - 100 360 - 450 - 490 µA NOTE: For dual-supply systems theoretical worst case (VI = 2.4V, VCC = 5.5V) specification is 1.8mA. HCT Input Loading Table INPUT UNIT LOADS All 0.35 NOTE: Unit Load is ∆ICC limit specified in DC Electrical Table, e.g. 360µA max at 25oC. Prerequisite for Switching Specifications 25oC PARAMETER SYMBOL -40oC TO 85oC -55oC TO 125oC VCC (V) MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS 2 100 - - 125 - - 150 - - ns 4.5 20 - - 25 - - 30 - - ns 6 17 - - 21 - - 26 - - ns 2 100 - - 125 - - 150 - - ns 4.5 20 - - 25 - - 30 - - ns 6 17 - - 21 - - 26 - - ns HC TYPES Minimum Input, Pulse Width tWL A B tWH 4 CD74HC123, CD74HCT123, CD74HC423, CD74HCT423 Prerequisite for Switching Specifications (Continued) 25oC PARAMETER R A and B Hold Time Reset Removal Time Retrigger Time Number -55oC TO 125oC SYMBOL VCC (V) MIN TYP MAX MIN TYP MAX MIN TYP MAX UNITS tWL 2 100 - - 125 - - 150 - 150 ns 4.5 20 - - 25 - - 30 - 30 ns 6 17 - - 21 - - 26 - 26 ns 2 50 - - 65 - - 75 - 75 ns 4.5 10 - - 13 - - 15 - 15 ns 6 9 - - 11 - - 13 - 13 ns 2 50 - - 65 - - 75 - 75 ns 4.5 10 - - 13 - - 15 - 15 ns 6 9 - - 11 - - 13 - 13 ns 5 - - - - - - - - - ns - 50 - - 63 - - 76 - ns 40 - 50 38.7 - 51.3 38.2 - 51.8 µs tH tREM trT RX = 10KΩ, CX = 0 Output Pulse Width -40oC TO 85oC tW 5 Q or Q RX = 10KΩ, CX = 10nF HCT TYPES Minimum Input, Pulse Width tWL 5 A 20 - - 25 - - 30 - - ns B tWH 20 - - 25 - - 30 - - ns R tWL 20 - - 25 - - 30 - - ns - - ns - ns A and B Hold Time tH 5 10 - - 13 - - 15 tREM 5 10 - - 13 - - 15 RX = 10KΩ, CX = 0 trT 5 - 50 - - 63 - - 76 - ns Output Pulse Width Q or Q tW 5 40 - 50 38.7 - 51.3 38.2 - 51.8 µs Reset Removal Time Retrigger Time Number (Note 4) RX = 10KΩ, CX = 10nF NOTE: 4. Time to trigger depends on the values of RX and CX. The output pulse width can only be extended when the time between the activegoing edges of the trigger input pulses meet the minimum retrigger time requirement. 5 CD74HC123, CD74HCT123, CD74HC423, CD74HCT423 Switching Specifications CL = 50pF, Input tr, tf = 6ns, RX = 10KΩ, CX = 0 -40oC TO 85oC 25oC PARAMETER SYMBOL TEST CONDITIONS tPHL CL = 50pF -55oC TO 125oC VCC (V) MIN TYP MAX MIN MAX MIN MAX UNITS 2 - - 300 - 375 - 450 ns 4.5 - - 60 - 75 - 90 ns CL = 15pF 5 - 25 - - - - - ns CL = 50pF 6 - - 51 - 64 - 76 ns CL = 50pF 2 - - 320 - 400 - 480 ns 4.5 - - 64 - 80 - 96 ns CL = 15pF 5 - 26 - - - - - ns CL = 50pF 6 - - 54 - 68 - 82 ns CL = 50pF 2 - - 215 - 270 - 325 ns 4.5 - - 43 - 54 - 65 ns 6 - - 37 - 46 - 55 ns 2 - - 75 - 95 - 110 ns 4.5 - - 15 - 19 - 22 ns 6 - - 13 - 16 - 19 ns - 45 - - - - - µs - ±2 - - - - - % HC TYPES Trigger Propagation Delay A, B, R to Q A, B, R to Q Reset Propagation Delay tPHL tPHL, tPLH R to Q or Q Output Transition Time Output Pulse Width tTHL, tTLH - CL = 50pF - 5 RX = 10KΩ, CX = 10pF Pulse Width Match Between Circuits In the Same Package - - 5 RX = 10KΩ, CX = 10pF Power Dissipation Capacitance CPD CL = 15pF 5 - - - - - - - pF Input Capacitance CIN CL = 50pF - 10 - 10 - 10 - 10 pF NOTES: 5. CPD is used to determine the dynamic power consumption, per multivibrator. 6. PD = (CPD + CX) VCC2 fi ∑(CL VCC2 fO) where fi = input frequency, fO = Output Frequency, CL = Output Load Capacitance, I CX = External Capacitance VCC = Supply Voltage assuming fi « -----tW 6 CD74HC123, CD74HCT123, CD74HC423, CD74HCT423 Test Circuits and Waveforms A B = LOW A A = HIGH B = LOW A = HIGH B B R R VS VS tW tW tW VS Q VS Q tW tW tW FIGURE 1. OUTPUT PULSE CONTROL USING RESET INPUT (R) PULSE FOR 123 tW FIGURE 2. OUTPUT PULSE CONTROL USING RESET INPUT (R) FOR 423 A B tW B (R = HIGH) A trT Q VS tW tW tW NOTE: Output pulse control using retrigger pulse for 123 and 423. 8 6 4 2 0.9 EXTERNAL CAPACITANCE (CX) = 10nF 0.8 103 8 6 4 2 102 101 Ω 0k RX Ω 0k 8 6 4 2 RX 8 6 4 2 103 = =1 4 68 2 4 68 2 4 68 2 105 104 106 EXTERNAL CAPACITANCE (CX) - pF 0.6 HCT 0.5 0.4 0.3 DC SUPPLY VOLTAGE (VCC) = 5V AMBIENT TEMPERATURE (TA) = 25oC 2 EXTERNAL RESISTANCE (RX) = 10kΩ TO 100kΩ AMBIENT TEMPERATURE (TA) = 25oC 0.7 10 “K” FACTOR OUTPUT PULSE WIDTH (µs) FIGURE 3. TRIGGERING OF ONE SHOT BY INPUT A OR INPUT B FOR A PERIOD tW 0.2 0.1 4 68 107 FIGURE 4. TYPICAL OUTPUT PULSE WIDTH AS A FUNCTION OF CX FOR RX = 10kΩ AND 100kΩ 1 2 3 4 5 6 7 8 9 DC SUPPLY VOLTAGE (VCC) - VOLTS 10 11 FIGURE 5. TYPICAL “K” FACTOR AS A FUNCTION OF VCC 7 IMPORTANT NOTICE Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those pertaining to warranty, patent infringement, and limitation of liability. TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER’S RISK. In order to minimize risks associated with the customer’s applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. TI’s publication of information regarding any third party’s products or services does not constitute TI’s approval, warranty or endorsement thereof. Copyright 1998, Texas Instruments Incorporated