TI1 LM1971M Overture audio attenuator series digitally controlled 62 db audio attenuator Datasheet

LM1971
www.ti.com
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
LM1971 Overture™ Audio Attenuator Series Digitally Controlled 62 dB Audio Attenuator
with/Mute
Check for Samples: LM1971
FEATURES
DESCRIPTION
•
•
•
•
The LM1971 is a digitally controlled single channel
audio attenuator fabricated on a CMOS process.
Attenuation is variable in 1 dB steps from 0 dB to −62
dB. A mute function disconnects the input from the
output, providing over 100 dB of attenuation.
1
23
3-Wire Serial Interface
Mute Function
Click and Pop Free Attenuation Changes
8-Pin Plastic PDIP and SOIC Packages
Available
APPLICATIONS
•
•
•
•
•
•
Communication Systems
Cellular Phones and Pagers
Personal Computer Audio Control
Electronic Music (MIDI)
Sound Reinforcement Systems
Audio Mixing Automation
KEY SPECIFICATIONS
•
•
•
•
•
Total Harmonic Distortion 0.0008 % (Typ)
Frequency Response > 200 kHz (−3 dB) (Typ)
Attenuation Range (Excluding Mute) 62 dB
(Typ)
Dynamic Range 115 dB (Typ)
Mute Attenuation 102 dB (Typ)
The performance of the device is exhibited by its
ability to change attenuation levels without audible
clicks or pops. In addition, the LM1971 features a low
Total Harmonic Distortion (THD) of 0.0008%, and a
Dynamic Range of 115 dB, making it suitable for
digital audio needs. The LM1971 is available in both
8-pin plastic PDIP or SOIC packages.
The LM1971 is controlled by a TTL/CMOS compatible
3-wire serial digital interface. The active low LOAD
line enables the data input registers while the CLOCK
line provides system timing. Its DATA pin receives
serial data on the rising edge of each CLOCK pulse,
allowing the desired attenuation setting to be
selected.
Typical Application
Figure 1. Typical Audio Attenuator Application Circuit
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Overture is a trademark of dcl_owner.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 1995–2013, Texas Instruments Incorporated
LM1971
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
www.ti.com
Connection Diagram
Figure 2. Dual-In-Line Plastic or Surface Mount Package- Top View
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings (1) (2) (3)
Supply Voltage, VDD
15V
(GND −0.2V) to (VDD +0.2V)
Voltage at any pin
ESD Susceptibility (4)
Soldering Information
3000V
P Package (10s)
260°C
D Package
Vapor Phase (60s)
Infrared (15s)
Power Dissipation (5)
215°C
220°C
150 mW
Junction Temperature
150°C
Storage Temperature
−65°C to +150°C
(1)
(2)
(3)
(4)
(5)
All voltages are measured with respect to the GND pin (pin 3), unless otherwise specified.
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not specify specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Human body model, 100 pF discharged through a 1.5 kΩ resistor.
The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, θJA, and the ambient temperature
TA. The maximum allowable power dissipation is PD = (TJMAX – TA)/θJA or the number given in the Absolute Maximum Ratings,
whichever is lower. For the LM1971N and LM1971M, TJMAX = +150°C, and the typical junction-to-ambient thermal resistance, θJA, when
board mounted is 102° C/W and 167° C/W, respectively.
Operating Ratings (1) (2)
Temperature Range
Thermal Resistance
TMIN ≤ TA ≤ TMAX
167°C/W
P0008E Package, θJA
102°C/W
Supply Voltage
(1)
(2)
2
−40°C ≤ TA ≤ +85°C
D0008A Package, θJA
4.5V to 12V
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not specify specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
All voltages are measured with respect to the GND pin (pin 3), unless otherwise specified.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
LM1971
www.ti.com
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
Electrical Characteristics
(1) (2)
The following specifications apply for VDD = +12V (VREFIN = +6V), VIN = 5.5 Vpk, and f = 1 kHz, unless otherwse specified.
Limits apply for TA = 25°C. Digital inputs are TTL and CMOS compatible.
Symbol
Parameter
Conditions
LM1971
Typical (3)
Limit (4)
Units
(Limits)
IS
Supply Current
Digital Inputs Tied to 6V
1.8
3
mA (max)
THD
Total Harmonic Distortion
VIN = 0.5Vpk@ 0 dB Attenuation
0.0008
0.003
% (max)
eIN
Noise
Input is AC Grounded @ −12 dB
Attenuation
A-Weighted (5)
4.0
DR
Dynamic Range
Referenced to Full Scale = +6 Vpk
115
AM
Mute Attenuation
μV
dB
102
96
dB (min)
Attenuation Step Size Error
0 dB to −62 dB
0.009
0.2
dB (max)
Absolute Attenuation
Attenuation @ 0 dB
Attenuation @ −20 dB
Attenuation @ −40 dB
Attenuation @ −60 dB
Attenuation @ −62 dB
0.1
−20.3
−40.5
−60.6
−62.6
0.5
−19.0
−38.0
−57.0
−59.0
dB (min)
dB (min)
dB (min)
dB (min)
dB (min)
Analog Input Leakage Current
Input is AC Grounded
5.8
100
nA (max)
Frequency Response
20 Hz–100 kHz
±0.1
RIN
AC Input Impedance
Pin 8, VIN = 1.0 Vpk, f = 1 kHz
40
20
60
kΩ (min)
kΩ (max)
IIN
Input Current
@ Pins 4, 5, 6 @ 0V < VIN < 5V
1.0
100
nA (max)
fCLK
Clock Frequency
2
MHz (max)
VIH
High-Level Input Voltage
@ Pins 4, 5, 6
2.0
V (min)
VIL
Low-Level Input Voltage
@ Pins 4, 5, 6
0.8
V (max)
ILEAK
(1)
(2)
(3)
(4)
(5)
3
dB
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is functional, but do not specify specific performance limits. Electrical Characteristics state DC and AC electrical
specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the
Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication
of device performance.
All voltages are measured with respect to the GND pin (pin 3), unless otherwise specified.
Typicals are measured at 25°C and represent the parametric norm.
Limits are specifications that all parts are tested in production to meet the stated values.
Due to production test limitations, there is no limit for the Noise test. Please refer to Figure 5 and Figure 8 in Typical Performance
Characteristics.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
3
LM1971
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
www.ti.com
Pin Descriptions
VREFIN (1): The VREFIN pin provides the reference for the analog input signal. This pin should be biased at half of
the supply voltage, VDD, as shown in Figure 1 and Figure 19.
OUT (2): The attenuated analog output signal comes from this pin.
GND (3): The GND pin references the digital input signals and is the lower voltage reference for the IC.
Typically this pin would be labeled “VSS” but the ground reference for the digital logic input control is tied to
this same point. With a higher pin-count there would generally be separate pins for these functions; VSS
and Logic Ground. It is intended that the LM1971 always be operated using a single voltage supply
configuration, for which pin 3 (GND) should always be at system ground. If a bipolar or split-supply
configuration are desired, level shifting circuitry is needed for the digital logic control pins as they would be
referenced through pin 3 which would be at the negative supply. It is highly recommended, however, that
the LM1971 be used in a unipolar or single-supply configuration.
LOAD (4): The LOAD input accepts a TTL or CMOS level signal. This is the enable pin of the device, allowing
data to be clocked in while this input is low (0V). The GND pin is the reference for this signal.
DATA (5): The DATA input accepts a TTL or CMOS level signal. This pin is used to accept serial data from a
microcontroller that will be latched and decoded to change the channel's attenuation level. The GND pin is
the reference for this signal.
CLOCK (6): The CLOCK input accepts a TTL or CMOS level signal. The clock input is used to load data into the
internal shift register on the rising edge of the input clock waveform. The GND pin is the reference for this
signal.
VDD (7): The positive voltage supply should be placed to this pin.
IN (8): The analog input signal should be placed to this pin.
4
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
LM1971
www.ti.com
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
Typical Performance Characteristics
Supply Current vs
Supply Voltage
Supply Current vs
Temperature
Figure 3.
Figure 4.
Noise Floor
Analog Measurement
THD + N
vs
Freq and Amp
Figure 5.
Figure 6.
THD + N
vs
Freq and Amp
Noise Floor Spectrum by FFT
Figure 7.
Figure 8.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
5
LM1971
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
6
THD + N
vs
Amplitude
THD + N
vs
Amplitude
Figure 9.
Figure 10.
Mute Attenuation
vs Frequency
THD
vs
Freq by FFT
Figure 11.
Figure 12.
THD
vs
Freq by FFT
Output Impedance vs
Attenuation Level
Figure 13.
Figure 14.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
LM1971
www.ti.com
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
APPLICATION INFORMATION
SERIAL DATA FORMAT
The LM1971 uses a 3-wire serial communication format that is easily controlled by a microcontroller. The timing
for the 3-wire set, comprised of DATA, CLOCK, and LOAD is shown in Figure 15. As depicted in Figure 15, the
LOAD line is to go low at least 150 ns before the rising edge of the first clock pulse and is to remain low
throughout the transmission of the 16 data bits. The serial data is composed of an 8-bit address, which must
always be set to 0000 0000 to select the single audio channel, and 8 bits for attenuation setting. For both
address data and attenuation setting data, the MSB is sent first with the address data preceding the attenuation
data. Please refer to Figure 16 to confirm the serial data format transfer process.
Table 1 shows the various Address and Data byte values for different attenuation settings. Note that Address
bytes other than 0000 0000 are ignored.
μPOT SYSTEM ARCHITECTURE
The μPot's digital interface is essentially a shift register where serial data is shifted in, latched, and then
decoded. Once new data is shifted in, the LOAD line goes high, latching in the new data. The data is then
decoded and the appropriate switch is activated to set the desired attenuation level. This process is continued
each and every time an attenuation change is made. When the µPot is powered up, it is placed into the Mute
mode.
μPOT DIGITAL COMPATIBILITY
The μPot's digital interface section is compatible with TTL or CMOS logic. The shift register inputs act upon a
threshold of two diode drops above the ground level (Pin 3) or approximately 1.4V.
Table 1. Attenuator Register Set Description
Address Register (Byte 0)
MSB LSB
A7–A0
0000 0000
Channel 1
0000 0001
Ignored
0000 0010
Ignored
Data Register (Byte 1)
Contents
Attenuation (dB)
MSB LSB
D7–D0
0000 0000
0.0
0000 0001
1.0
0000 0010
2.0
0000 0011
3.0
:::::
::
0001 0000
16.0
0001 0001
17.0
0001 0010
18.0
0001 0011
19.0
:::::
::
0011 1101
61.0
0011 1110
62.0
0011 1111
96 (Mute)
0100 0000
96 (Mute)
:::::
::
1111 1110
96 (Mute)
1111 1111
96 (Mute)
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
7
LM1971
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
www.ti.com
*Note: Load and clock falling edges can be coincident, however, the clock falling edge cannot be delayed more than
20 ns from the falling edge of load. It is preferrable that the falling edge of clock occurs before the falling edge of load.
Figure 15. Timing Diagram
Figure 16. Serial Data Format Transfer Process
μPOT LADDER ARCHITECTURE
The μPot contains a chain of R1/R2 resistor dividers in a ladder form, as shown in Figure 17. Each R1 is actually
a series of 8 resistors, with a CMOS switch that taps into the resistor chain according to the attenuation level
chosen. For any given attenuation setting, there is only one CMOS switch closed (no paralleling of ladders). The
input impedance therefore remains constant, while the output impedance changes as the attenuation level
changes. It is important to note that the architecture is a series of resistor dividers, and not a straight, tapped
resistor, so the μPot is not a variable resistor; it is a variable voltage divider.
Figure 17. Resistor Ladder Architecture
8
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
LM1971
www.ti.com
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
ATTENUATION STEP SCHEME
The fundamental attenuation step scheme for the LM1971 is shown in Figure 18. It is also possible to obtain any
integer value attenuation step through programming, in addition to the 2 dB and 4 dB steps shown in Figure 18.
All higher attenuation step schemes can have clickless and popless performance. Although it is possible to “skip”
attenuation points by not sending all of the data, clickless and popless performance will suffer. It is highly
recommended that all of the data points should be sent for each attenuation level. This ensures flawless
operation and performance when making steps larger than 1 dB.
Figure 18. LM 1971 Channel Attenuation
vs Digital Step Value
(1 dB, 2 dB, and 4 dB Steps)
INPUT IMPEDANCE
The input impedance of a μPot is constant at a nominal 40 kΩ. Since the LM1971 is a single-supply operating
device, it is necessary to have both input and output coupling caps as shown in Figure 1. To ensure full lowfrequency response, a 1 μF coupling cap should be used.
OUTPUT IMPEDANCE
The output impedance of a μPot varies typically between 25 kΩ and 35 kΩ and changes nonlinearly with step
changes. Since a μPot is made up of a resistor ladder network with logarithmic attenuation, the output
impedance is nonlinear. Due to this configuration, a μPot cannot be considered as a linear potentiometer; it is a
logarithmic attenuator.
The linearity of a μPot cannot be measured directly without a buffer because the input impedance of most
measurement systems is not high enough to provide the required accuracy. The lower impedance of the
measurement system would load down the output and an incorrect reading would result. To prevent loading, a
JFET input op amp should be used as the buffer/amplifier.
OUTPUT BUFFERING
There are two performance issues to be aware of that are related to a μPot's output stage. The first concern is to
prevent audible clicks with attenuation changes, while the second is to prevent loading and subsequent linearity
errors. The output stage of a μPot needs to be buffered with a low input bias current op amp to keep DC shifts
inaudible. Additionally, the output of μPot needs to see a high impedance to keep linearity errors low.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
9
LM1971
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
www.ti.com
Attenuation level changes cause changes in the output impedance of a μPot. Output impedance changes in the
presence of a large input bias current for a buffer/amplifier will cause a DC shift to occur. Neglecting amplifier
gains and speaker sensitivities, the audibility of a DC shift is dependent upon the output impedance change
times the required input bias current. As an example, a 5 kΩ impedance change times a 1 μA bias current results
in a 5 mV DC shift; a level that is barely audible without any music material in the system. An op amp with a bias
current of 200 pA for the same 5 kΩ change results in an inaudible 1 μV DC shift. Since the worst case output
impedance changes are on the order of several kΩ, a bias current much less than 1 μA is required for highest
performance. In order to further quantify DC shifts, please refer to Figure 14 in Typical Performance
Characteristics and relate worst case impedance changes to the selected buffer/amplifier input bias current.
Without the use of a high input impedance (> 1 MΩ) op amp for the buffer/amplifier, loading will occur that
causes linearity errors in the signal. To ensure the highest level of performance, a JFET or CMOS input high
input impedance op amp is required.
One common application that requires gain at the output of a μPot is input signal volume control. Depending
upon the input source material, the LM1971 provides a means of controlling the input signal level. With a supply
voltage range of 4.5V to 12V, the LM1971 has the ability of controlling fairly inconsistent input source signal
levels. Using an op amp with gain at the μPot's output, as shown in Figure 20, will also allow the system dynamic
range to be increased. JFET op amps like the LF351 and the LF411 are well suited for this application. If active
half-supply buffering is also desired, dual op amps like the LF353 and the LF412 could be used.
For low voltage supply applications, op amps like the CMOS LMC6041 are preferred. This part has a supply
operating range from 4.5V–15.5V and also comes in a surface mount package.
μPOT HALF-SUPPLY REFERENCING
The LM1971 operates off of a single supply, with half-supply biasing supplied at the VREFIN terminal (Pin 1). The
easiest and most cost effective method of providing this half-supply is a simple resistor divider and bypass
capacitor network shown in Figure 1. The capacitor not only stabilizes the half-supply node by “holding” the
voltage nearly constant, but also decouples high frequency signals on the supply to ground. Signal feedthrough,
power supply ripple and fluctuations that are not properly filtered could cause the performance of the LM1971 to
be degraded.
A more stable half-supply node can be obtained by actively buffering the resistor divider network with a voltage
follower as shown in Figure 19. Supply fluctuations are then isolated by the high input impedance/low output
impedance mismatch associated with effective filtering. Since the LM1971 is a single channel device, using a
dual JFET input op amp is optimum for both output buffering and half-supply biasing.
A 10 μF capacitor or larger is recommended for better half-supply stabilization. For added rejection of higher
frequency power supply fluctuations, a smaller capacitor (0.01 μF–0.1 μF) could be added in parallel to the 10 μF
capacitor.
Figure 19. Higher Performance
Active Half-Supply Buffering
10
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
LM1971
www.ti.com
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
Figure 20. Active Reference with Active Gain Buffering
LOGARITHMIC GAIN AMPLIFIER
The μPot is capable of being used in the feedback loop of an op amp to create a gain controlled amplifier as
shown in Figure 21. In this configuration the attenuation levels from Table 1 become gain levels with the largest
possible gain value being 62 dB. For most applications, 62 dB of gain will cause signal clipping to occur.
However, this can be controlled through programming. It is important to note that when in mute mode the input is
disconnected from the output, thus placing the amplifier in open-loop gain state. In this mode, the amplifier will
behave as a comparator. Care should be taken with the programming and design of this type of circuit. To
provide the best overall performance, a high input impedance, low input bias current op amp should be used.
Figure 21. Logarithmic Gain Amplifier Circuit
MUTE FUNCTION
A major feature of the LM1971 is its ability to mute the input signal to an attenuation level of 102 dB. This is
accomplished internally by physically disconnecting the output from the input while also grounding the output pin
through approximately 2 kΩ.
The mute function is obtained during power-up of the device or by sending any binary data of 0011 1111 and
above serially to the device. The device may be placed into mute at any time during operation, allowing the
designer to make the mute command accessible to the end-user.
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
11
LM1971
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
www.ti.com
DC INPUTS
Although the μPot was designed to be used as an attenuator for signals within the audio spectrum, it is also
capable of tracking and attenuating an input DC voltage. The device will track voltages to either supply rail.
One point to remember about DC tracking is that with a buffer at the output of the μPot, the resolution of DC
tracking will depend upon the gain configuration of that output buffer and its supply voltage. Also, the output
buffer's supply voltage does not have to be the same as the μPot's supply voltage. Giving the buffer some gain
can provide more resolution when tracking small DC voltages.
12
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
LM1971
www.ti.com
SNAS104B – FEBRUARY 1995 – REVISED APRIL 2013
REVISION HISTORY
Changes from Revision A (April 2013) to Revision B
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 12
Submit Documentation Feedback
Copyright © 1995–2013, Texas Instruments Incorporated
Product Folder Links: LM1971
13
PACKAGE OPTION ADDENDUM
www.ti.com
18-Oct-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM1971M
ACTIVE
SOIC
D
8
95
TBD
Call TI
Call TI
-40 to 85
LM19
71M
LM1971M/NOPB
ACTIVE
SOIC
D
8
95
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
LM19
71M
LM1971MX
ACTIVE
SOIC
D
8
2500
TBD
Call TI
Call TI
-40 to 85
LM19
71M
LM1971MX/NOPB
ACTIVE
SOIC
D
8
2500
Green (RoHS
& no Sb/Br)
SN | CU SN
Level-1-260C-UNLIM
-40 to 85
LM19
71M
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
18-Oct-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Oct-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM1971MX
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
LM1971MX/NOPB
SOIC
D
8
2500
330.0
12.4
6.5
5.4
2.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Oct-2013
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM1971MX
SOIC
D
8
2500
367.0
367.0
35.0
LM1971MX/NOPB
SOIC
D
8
2500
367.0
367.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Texas Instruments:
LM1971M LM1971M/NOPB LM1971MX LM1971MX/NOPB
Similar pages