TI1 LMK00105SQE Ultra-low jitter lvcmos fanout buffer and level translator Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
LMK00105 Ultra-Low Jitter LVCMOS Fanout Buffer and Level Translator With Universal
Input
1 Features
3 Description
•
•
The LMK00105 is a high-performance, low-noise
LVCMOS fanout buffer which can distribute five ultralow jitter clocks from a differential, single-ended, or
crystal input. The LMK00105 supports synchronous
output enable for glitch-free operation. The ultra lowskew, low-jitter, and high PSRR make this buffer
ideally suited for various networking, telecom, server
and storage area networking, RRU LO reference
distribution, medical and test equipment applications.
1
•
•
•
•
•
•
•
5 LVCMOS Outputs, DC to 200 MHz
Universal Input
– LVPECL
– LVDS
– HCSL
– SSTL
– LVCMOS and LVTTL
Crystal Oscillator Interface
– Crystal Input Frequency: 10 to 40 MHz
Output Skew: 6 ps
Additive Phase Jitter
– 30 fs at 156.25 MHz (12 kHz to 20 MHz)
Low Propagation Delay
Operates With 3.3 or 2.5-V Core Supply Voltage
Adjustable Output Power Supply
– 1.5 V, 1.8 V, 2.5 V, and 3.3 V for Each Bank
24-Pin WQFN Package (4.0 mm × 4.0 mm ×
0.8 mm)
The core voltage can be set to 2.5 or 3.3 V, while the
output voltage can be set to 1.5, 1.8, 2.5 or 3.3 V.
The LMK00105 can be easily configured through pin
programming.
Device Information(1)
PART NUMBER
LMK00105
PACKAGE
BODY SIZE (NOM)
WQFN (24)
4.00 mm × 4.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Functional Block Diagram
2 Applications
•
•
•
•
•
•
•
•
LO Reference Distribution for RRU Applications
SONET, Ethernet, Fibre Channel Line Cards
Optical Transport Networks
GPON OLT/ONU
Server and Storage Area Networking
Medical Imaging
Portable Test and Measurement
High-End A/V
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Diagrams..........................
Specifications.........................................................
1
1
1
2
4
5
6.1
6.2
6.3
6.4
6.5
6.6
5
5
5
5
6
8
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 9
7.1
7.2
7.3
7.4
Overview ................................................................... 9
Functional Block Diagram ......................................... 9
Feature Description................................................... 9
Device Functional Modes........................................ 11
8
Application and Implementation ........................ 12
8.1 Application Information............................................ 12
8.2 Typical Applications ................................................ 14
9
Power Supply Recommendations...................... 20
9.1 Power Supply Filtering ............................................ 20
9.2 Power Supply Ripple Rejection............................... 20
9.3 Power Supply Bypassing ........................................ 21
10 Layout................................................................... 21
10.1 Layout Guidelines ................................................. 21
10.2 Layout Example .................................................... 22
10.3 Thermal Management ........................................... 22
11 Device and Documentation Support ................. 23
11.1
11.2
11.3
11.4
Documentation Support ........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
23
23
24
24
12 Mechanical, Packaging, and Orderable
Information ........................................................... 24
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision F (May 2013) to Revision G
•
Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision E (February 2013) to Revision F
Page
•
Added device name to title of document. ............................................................................................................................... 1
•
Changed all LLP and QFN packages to WQFN throughout document.................................................................................. 1
•
Deleted optional from CLKin* pin description. And changed complimentary to complementary. .......................................... 4
•
Added max limit to Output Skew parameter and added tablenote to parameter in Electrical Characteristics Table............. 6
•
Changed typical value for both conditions of Propagation Delay in the Electrical Characteristics Table. ............................. 6
•
Added Min/Max limits to both conditions of Propagation Delay parameter in Electrical Characteristics Table. .................... 6
•
Changed unit value for the first condition of Part-to-part Skew from ps to ns in the Electrical Characteristics Table. .......... 6
•
Changed both Max values of each Part-to-part Skew condition in Electrical Characteristics Table...................................... 6
•
Changed the Typ value of each Rise/Fall Time condition in the Electrical Characteristics Table. ....................................... 6
•
Deleted VIL table note. ............................................................................................................................................................ 7
•
Added VI_SE parameter and spec limits with corresponding table note to Electrical Characteristics Table. .......................... 7
•
Added CLKin* column to CLKin Input vs. Output States table. Also added fourth row starting with Logic Low under
CLKin column. ...................................................................................................................................................................... 10
•
Changed table title from CLKin input vs. Output States to OSCin Input vs. Output States ................................................. 10
•
Changed third paragraph in Driving the Clock Inputs section to include CLKin* and LVCMOS text. Removed extra
references to other figures. Revised to better correspond with information in Electrical Characteristics Table. ................. 12
•
Deleted Figure 10 (Near End termination) and Figure 11 (Far End termination) from Driving the Clock Inputs section..... 12
•
Changed bypass cap text to signal attenuation text of the fourth paragraph in Driving the Clock Inputs section. .............. 12
•
Changed Single-Ended LVCMOS Input, DC Coupling with Common Mode Biasing image with revised graphic............... 13
•
Deleted sentence in reference to two deleted images. ........................................................................................................ 13
2
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
•
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
Changed link from National packaging site to TI packaging site.......................................................................................... 22
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
3
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
5 Pin Configuration and Diagrams
24
23
22
21
20
19
OE
Vdd
SEL
CLKin
CLKin*
GND
24-Pin
WQFN Package
Top View
1
2
3
4
5
6
DAP
18
17
16
15
14
13
Vddo
CLKout4
GND
CLKout3
Vddo
CLKout2
GND
Vdd
OSCin
OSCout
GND
GND
7
8
9
10
11
12
GND
Vddo
CLKout0
GND
CLKout1
Vddo
Pin Functions
PIN
(1)
4
NAME
NO
DAP
DAP
TYPE
DESCRIPTION
—
The DAP should be grounded
Vddo
2, 6
Power
Power Supply for Bank A (CLKout0 and CLKout 1) CLKout pins.
CLKout0
3
Output
LVCMOS Output
GND
1,4,7,11,
12, 16,19
GND
CLKout1
5
Output
LVCMOS Output
Vdd
8,23
Power
Supply for operating core and input buffer
OSCin
9
Input
Input for Crystal
Ground
OSCout
10
Output
Output for Crystal
CLKout2
13
Output
LVCMOS Output
Vddo
14,18
Power
Power Supply for Bank B (CLKout2 to CLKout 4) CLKout pins
CLKout3
15
Output
LVCMOS Output
CLKout4
17
Output
LVCMOS Output
CLKin*
20
Input
Complementary input pin
CLKin
21
Input
Input Pin
SEL
22
Input
Input Clock Selection. This pin has an internal pulldown resistor. (1)
OE
24
Input
Output Enable. This pin has an internal pulldown resistor. (1)
CMOS control input with internal pulldown resistor.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
6 Specifications
6.1 Absolute Maximum Ratings (1)
MIN
MAX
UNIT
Vdd
Core Supply Voltage
–0.3
3.6
V
Vddo
Output Supply Voltage
–0.3
3.6
V
VIN
Input Voltage
–0.3
Vdd + 0.3
V
TL
Lead Temperature (solder 4 s)
260
°C
TJ
Junction Temperature
125
°C
Tstg
Storage temperature
150
°C
(1)
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2500
Charged-device model (CDM), per JEDEC specification JESD22C101 (2)
±1000
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
MIN
TA
Ambient Temperature
Vdd
Core Supply Voltage
Vddo
Output Supply Voltage
(1)
(1)
TYP
MAX
UNIT
–40
25
85
°C
2.375
3.3
3.45
V
1.425
3.3
Vdd
V
Vddo should be less than or equal to Vdd (Vddo ≤ Vdd)
6.4 Thermal Information
LMK00105
THERMAL METRIC
(1)
RTW
UNIT
24 PINS
RθJA
Junction-to-ambient thermal resistance
46.7
RθJC(top)
Junction-to-case (top) thermal resistance
50.3
RθJB
Junction-to-board thermal resistance
25.5
ψJT
Junction-to-top characterization parameter
1.9
ψJB
Junction-to-board characterization parameter
25.6
RθJC(bot)
Junction-to-case (bottom) thermal resistance
13.6
(1)
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
5
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
6.5 Electrical Characteristics
(2.375 V ≤ Vdd ≤ 3.45 V, 1.425 ≤ Vddo ≤ Vdd, -40 °C ≤ TA ≤ 85 °C, Differential inputs. Typical values represent most likely
parametric norms at Vdd = Vddo = 3.3 V, TA = 25 °C, at the Recommended Operation Conditions at the time of product
characterization and are not ensured). Test conditions are: Ftest = 100 MHz, Load = 5 pF in parallel with 50 Ω unless
otherwise stated.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TOTAL DEVICE CHARACTERISTICS
Vdd
Core Supply Voltage
2.375
2.5 or 3.3
3.45
V
Vddo
Output Supply Voltage
1.425 1.5, 1.8, 2.5, or 3.3
Vdd
V
No CLKin
16
25
IVdd
Core Current
Vddo = 3.3 V, Ftest = 100 MHz
24
Vddo = 2.5 V, Ftest = 100 MHz
20
IVddo[n]
Current for Each Output
IVdd + IVddo
Total Device Current with
Loads on all outputs
Vddo = 2.5 V,
OE = High, Ftest = 100 MHz
5
Vddo= 3.3 V,
OE = High, Ftest = 100 MHz
7
OE = Low
0.1
OE = High @ 100 MHz
48
OE = Low
16
mA
mA
mA
POWER SUPPLY RIPPLE REJECTION (PSRR)
100 kHz, 100 mVpp
Ripple Injected on
Vdd, Vddo = 2.5 V
Ripple Induced
Phase Spur Level
PSRR
OUTPUTS
Measured between outputs,
referenced to CLKout0
(2)
Output Skew
tPD
Propagation Delay CLKin to
CLKout (2)
tPD, PP
fCLKout
tRise
Part-to-part Skew
(2) (3)
Output Frequency
(4)
Rise/Fall Time
VCLKoutLow
Output Low Voltage
VCLKoutHigh
Output High Voltage
RCLKout
Output Resistance
(1)
(2)
(3)
(4)
6
dBc
(1)
Skew
tj
-44
RMS Additive Jitter
6
25
ps
CL = 5 pF, RL = 50 Ω
Vdd = 3.3 V; Vddo = 3.3 V
0.85
1.4
2.2
ns
CL = 5 pF, RL = 50 Ω
Vdd = 2.5 V; Vddo = 1.5 V
1.1
1.8
2.8
ns
CL = 5 pF, RL = 50 Ω
Vdd = 3.3 V; Vddo = 3.3 V
0.35
ns
CL = 5 pF, RL = 50 Ω
Vdd = 2.5 V; Vddo = 1.5 V
0.6
ns
200
MHz
DC
Vdd = 3.3 V, Vddo = 1.8 V, CL = 10 pF
250
Vdd = 2.5 V, Vddo = 2.5 V, CL = 10 pF
275
Vdd = 3.3 V, Vddo = 3.3 V, CL = 10 pF
315
ps
0.1
Vddo-0.1
fCLKout = 156.25 MHz,
CMOS input slew rate ≥ 2 V/ns
CL = 5 pF, BW = 12 kHz to 20 MHz
V
50
ohm
30
fs
AC Parameters for CMOS are dependent upon output capacitive loading
Parameter is specified by design, not tested in production.
Part-to-part skew is calculated as the difference between the fastest and slowest tPD across multiple devices.
Specified by characterization.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
Electrical Characteristics (continued)
(2.375 V ≤ Vdd ≤ 3.45 V, 1.425 ≤ Vddo ≤ Vdd, -40 °C ≤ TA ≤ 85 °C, Differential inputs. Typical values represent most likely
parametric norms at Vdd = Vddo = 3.3 V, TA = 25 °C, at the Recommended Operation Conditions at the time of product
characterization and are not ensured). Test conditions are: Ftest = 100 MHz, Load = 5 pF in parallel with 50 Ω unless
otherwise stated.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
DIGITAL INPUTS (OE, SEL0, SEL1)
VLow
Input Low Voltage
VHigh
Input High Voltage
IIH
High Level Input Current
IIL
Low Level Input Current
Vdd = 2.5 V
0.4
Vdd = 2.5 V
1.3
Vdd = 3.3 V
1.6
V
50
-5
5
uA
CLKin/CLKin* INPUT CLOCK SPECIFICATIONS (5) (6)
IIH
High Level Input Current
VCLKin = Vdd
IIL
Low Level Input Current
VCLKin = 0 V
VIH
Input High Voltage
VIL
Input Low Voltage
Differential Input Common
Mode Input Voltage (7)
VCM
20
–20
uA
uA
Vdd
GND
V
VID = 150 mV
0.5
Vdd1.2
VID = 350 mV
0.5
Vdd1.1
VID = 800 mV
0.5
Vdd0.9
0.3
2
0.15
1.5
V
DC
200
MHz
10
40
MHz
VI_SE
Single-Ended Input Voltage
Swing (2)
CLKinX driven single-ended (AC or DC
coupled), CLKinX* AC coupled to GND
or externally biased within VCM range
VID
Differential Input Voltage
Swing
CLKin driven differentially
V
Vpp
OSCin/OSCout PINS
(4)
fOSCin
Input Frequency
fXTAL
Crystal Frequency Input
Range
COSCin
Shunt Capacitance
VIH
Input High Voltage
(5)
(6)
(7)
(8)
Single-Ended Input, OSCout floating
Fundamental Mode Crystal
ESR < 200 Ω ( fXtal ≤ 30 MHz )
ESR < 120 Ω ( fXtal > 30 MHz )
(4) (8)
1
Single-Ended Input, OSCout floating
pF
2.5
V
See Differential Voltage Measurement Terminology for definition of VOD and VID.
Refer to application note AN-912 Common Data Transmission Parameters and their Definitions for more information.
When using differential signals with VCM outside of the acceptable range for the specified VID, the clock must be AC coupled.
The ESR requirements stated are what is necessary in order to ensure that the Oscillator circuitry has no start up issues. However,
lower ESR values for the crystal might be necessary in order to stay below the maximum power dissipation requirements for that crystal.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
7
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
6.6 Typical Characteristics
Unless otherwise specified: Vdd = Vddo = 3.3 V, TA = 20 °C, CL = 5 pF, CLKin driven differentially, input slew rate ≥ 2 V/ns.
450
RMS JITTER (fs)
400
-40 C
25 C
85 C
CLKin Source
-140
Fclk-100 MHz
Int. BW=1-20 MHz
NOISE FLOOR (dBc/Hz)
500
350
300
250
200
150
100
-145
-40 C
25 C
85 C
CLKin Source
Fclk=100 MHz
Foffset=20 MHz
-150
-155
-160
-165
50
0
-170
0.5
1.0
1.5
2.0
2.5
3.0
DIFFERENTIAL INPUT SLEW RATE (V/ns)
Figure 1. RMS Jitter vs. CLKin Slew Rate @ 100 MHz
0.5
1.0
1.5
2.0
2.5
3.0
DIFFERENTIAL INPUT SLEW RATE (V/ns)
Figure 2. Noise Floor vs. CLKin Slew Rate @ 100 MHz
3.5
Vddo=1.5 V
Vddo=1.8 V
Vddo=2.5 V
Vddo=3.3 V
OUTPUT SWING (V)
3.0
LVCMOS Output
CLKin Source
2.5
Rterm=50
2.0
1.5
1.0
0.5
0.0
Test conditions: LVCMOS Input, slew rate ≥ 2 V/ns, CL = 5 pF in
parallel with 50 Ω, BW = 1 MHz to 20 MHz
Figure 3. LVCMOS Phase Noise @ 100 MHz
CURRENT (mA)
15
0
200
400
600
800
1000
FREQUENCY (MHz)
Figure 4. LVCMOS Output Swing vs. Frequency
Vddo = 1.5 V
Vddo = 1.8 V
Vddo = 2.5 V
Vddo = 3.3 V
Cload = 10 pF
10
5
0
0
100
150
200
250
FREQUENCY (MHz)
Figure 5. Iddo per Output vs Frequency
8
50
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
7 Detailed Description
7.1 Overview
The LMK00105 is a 5 output LVCMOS clock fanout buffer with low additive jitter that can operate up to 200 MHz.
It features a 2:1 input multiplexer with a crystal oscillator input, single supply or dual supply (lower power)
operation, and pin-programmable device configuration. The device is offered in a 24-pin WQFN package.
7.2 Functional Block Diagram
7.3 Feature Description
7.3.1 Vdd and Vddo Power Supplies
Separate core and output supplies allow the output buffers to operate at the same supply as the Vdd core supply
(3.3 V or 2.5 V) or from a lower supply voltage (3.3 V, 2.5 V, 1.8 V, or 1.5 V). Compared to single-supply
operation, dual supply operation enables lower power consumption and output-level compatibility.
Bank A (CLKout0 and CLKout1) and Bank B (CLKout2 to CLKout4) may also be operated at different Vddo
voltages, provided neither Vddo voltage exceeds Vdd.
NOTE
Care should be taken to ensure the Vddo voltage does not exceed the Vdd voltage to
prevent turning-on the internal ESD protection circuitry.
DO NOT DISCONNECT OR GROUND ANY OF THE Vddo PINS because the Vddo pins
are internally connected within an output bank.
7.3.2 Clock Input
The LMK00105 has one differential input, CLKin/CLKin* and OSCin, that can be driven in different manners that
are described in the following sections.
7.3.2.1 Selection of Clock Input
Clock input selection is controlled using the SEL pin as shown in Table 1. Refer to Clock Inputs for clock input
requirements. When CLKin is selected, the crystal circuit is powered down. When OSCin is selected, the crystal
oscillator will start-up and its clock will be distributed to all outputs. Refer to Crystal Interface for more
information. Alternatively, OSCin may be driven by a single ended clock, up to 200 MHz, instead of a crystal.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
9
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
Table 1. Input Selection
SEL
Input
0
CLKin, CLKin*
1
OSCin (Crystal Mode)
7.3.2.1.1 CLKin/CLKin* Pins
The LMK00105 has a differential input (CKLin/CLKin*) which can be driven single-ended or differentially. It can
accept AC or DC coupled 3.3V/2.5V LVPECL, LVDS, or other differential and single ended signals that meet the
input requirements in Electrical Characteristics and when using differential signals with VCM outside of the
acceptable range for the specified VID, the clock must be AC coupled. Refer to Clock Inputs for more details on
driving the LMK00105 inputs.
In the event that a Crystal mode is not selected and the CLKin pins do not have an AC signal applied to them,
Table 2 following will be the state of the outputs.
Table 2. CLKin Input vs. Output States
CLKin
CLKin*
Output State
Open
Open
Logic Low
Logic Low
Logic Low
Logic Low
Logic High
Logic Low
Logic High
Logic Low
Logic High
Logic Low
7.3.2.1.2 OSCin/OSCout Pins
The LMK00105 has a crystal oscillator which will be powered up when OSCin is selected. Alternatively, OSCin
may be driven by a single ended clock, up to 200 MHz, instead of a crystal. Refer to Crystal Interface for more
information. If Crystal mode is selected and the pins do not have an AC signal applied to them, Table 3 will be
the state of the outputs. If Crystal mode is selected an open state is not allowed on OSCin, as the outputs may
oscillate due to the crystal oscillator circuitry.
Table 3. OSCin Input vs. Output States
OSCin
Output State
Open
Not Allowed
Logic Low
Logic High
Logic High
Logic Low
7.3.3 Clock Outputs
The LMK00105 has 5 LVCMOS outputs.
7.3.3.1 Output Enable Pin
When the output enable pin is held High, the outputs are enabled. When it is held Low, the outputs are held in a
Low state as shown in Table 4.
Table 4. Output Enable Pin States
OE
Outputs
Low
Disabled (Hi-Z)
High
Enabled
The OE pin is synchronized to the input clock to ensure that there are no runt pulses. When OE is changed from
Low to High, the outputs will initially have an impedance of about 400 Ω to ground until the second falling edge of
the input clock and starting with the second falling edge of the input clock, the outputs will buffer the input. If the
OE pin is taken from Low to High when there is no input clock present, the outputs will either go high or low and
stay a that state; they will not oscillate. When the OE pin is taken from High to Low the outputs will be Low after
the second falling edge of the clock input and then will go to a Disabled (Hi-Z) state starting after the next rising
edge.
10
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
7.3.3.2 Using Less than Five Outputs
Although the LMK00105 has 5 outputs, not all applications will require all of these. In this case, the unused
outputs should be left floating with a minimum copper length to minimize capacitance. In this way, this output will
consume minimal output current because it has no load.
NOTE
For best soldering practices, the minimum trace length should extend to include the pin
solder mask. This way during reflow, the solder has the same copper area as connected
pins. This allows for good, uniform fillet solder joints helping to keep the IC level during
reflow.
7.4 Device Functional Modes
LMK00105 can be driven by a clock input or a crystal according to SEL pin. Refer to Selection of Clock Input for
more information.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
11
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
8 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
8.1.1 Clock Inputs
The LMK00105 has a differential input (CLKin/CLKin*) that can accept AC or DC coupled 3.3V/2.5V LVPECL,
LVDS, and other differential and single ended signals that meet the input requirements specified in Electrical
Characteristics. The device can accept a wide range of signals due to its wide input common mode voltage
range (VCM) and input voltage swing (VID)/dynamic range. AC coupling may also be employed to shift the input
signal to within the VCM range.
To achieve the best possible phase noise and jitter performance, it is mandatory for the input to have a high slew
rate of 2 V/ns (differential) or higher. Driving the input with a lower slew rate will degrade the noise floor and jitter.
For this reason, a differential input signal is recommended over single-ended because it typically provides higher
slew rate and common-mode noise rejection.
While it is recommended to drive the CLKin/CLKin* pair with a differential signal input, it is possible to drive it
with a single-ended clock provided it conforms to the Single-Ended Input specifications for CLKin pins listed in
the Electrical Characteristics. For large single-ended input signals, such as 3.3 V or 2.5 V LVCMOS, a 50 Ω load
resistor should be placed near the input for signal attenuation to prevent input overdrive as well as for line
termination to minimize reflections. The CLKin input has an internal bias voltage of about 1.4 V, so the input can
be AC coupled as shown in Figure 6. The output impedance of the LVCMOS driver plus Rs should be close to
50 Ω to match the characteristic impedance of the transmission line and load termination.
RS 0.1 PF
0.1 PF
50:Trace
50:
CMOS
Driver
LMK
Input
0.1 PF
Figure 6. Preferred Configuration: Single-Ended LVCMOS Input, AC Coupling
A single-ended clock may also be DC coupled to CLKin as shown in Figure 7. A 50-Ω load resistor should be
placed near the CLKin input for signal attenuation and line termination. Because half of the single-ended swing of
the driver (VO,PP / 2) drives CLKin, CLKin* should be externally biased to the midpoint voltage of the attenuated
input swing ((VO,PP / 2) × 0.5). The external bias voltage should be within the specified input common voltage
(VCM) range. This can be achieved using external biasing resistors in the kΩ range (RB1 and RB2) or another lownoise voltage reference. This will ensure the input swing crosses the threshold voltage at a point where the input
slew rate is the highest.
12
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
Application Information (continued)
CMOS
Driver
VO,PP
Rs
VO,PP/2
VCC
50:Trace
VBB ~ (VO,PP/2) x 0.5
50:
LMK
Input
RB1
VCC
RB2
0.1 PF
Figure 7. Single-Ended LVCMOS Input, DC Coupling With Common Mode Biasing
If the crystal oscillator circuit is not used, it is possible to drive the OSCin input with an single-ended external
clock as shown in Figure 8. The input clock should be AC coupled to the OSCin pin, which has an internally
generated input bias voltage, and the OSCout pin should be left floating. While OSCin provides an alternative
input to multiplex an external clock, it is recommended to use either differential input (CLKin) since it offers
higher operating frequency, better common mode, improved power supply noise rejection, and greater
performance over supply voltage and temperature variations.
Figure 8. Driving OSCin With a Single-Ended External Clock
8.1.2 Clock Outputs
The LMK00105 LVCMOS driver output impedance (Ro) is nominally 50 ohms and well-matched to drive a 50
ohm transmission line (Zo), as shown as below. If driving a transmission line with higher characteristic
impedance than 50 ohms, a series resistor (Rs) should be placed near the driver to provide source termination,
where Rs = Zo – Ro.
The LMK00105 has two output banks, Bank A and Bank B, which are separately powered by independent Vddo
supply pins. The Vddo supply pins for Bank A and Bank B are not connected together internally, and may be
supplied with different voltages. This allows the LMK00105 outputs to easily interface to multiple receivers with
different input threshold or input supply voltage (Vddi) requirements without the need for additional voltage
divider networks.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
13
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
Application Information (continued)
Figure 9. LMK00105 Output Termination
8.2 Typical Applications
8.2.1 Typical Application Block Diagram
Figure 10. Typical Application Block Diagram
14
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
Typical Applications (continued)
8.2.1.1 Design Requirements
In the example application shown in Figure 10, the LMK00105 is used to fan-out a 3.3-V LVCMOS oscillator to
three receiver devices with the following characteristics:
• The CPU input accepts a DC-coupled 3.3-V LVCMOS input clock. The LMK00105 has an internal 50-Ω series
termination, thus the receiver is connected directly to the output.
• The FPGA input also requires a 3.3-V LVCMOS input clock, like the CPU.
• The PLL input requires a single-ended voltage swing less than 2 Vpp, so 1.8-V LVCMOS input signaling is
needed. The PLL receiver requires AC coupling since it has internal input biasing to set its own common
mode voltage level.
8.2.1.2 Detailed Design Procedure
Refer to Clock Inputs to properly interface the 3.3-V LVCMOS oscillator output to the CLKin input buffer of the
LMK00105.
See Figure 9 for output termination schemes depending on the receiver application. Since the CPU/FPGA inputs
and PLL input require different input voltage levels, the LMK00105 output banks are supplied from separate
Vddo rails of 3.3 V and 1.8 V for CLKout0/1 (Bank A) and CLKout2 (Bank B), respectively.
Unused outputs can be left floating.
See Power Supply Recommendations for recommended power supply filtering and decoupling/bypass
techniques.
8.2.1.3 Application Curves
The LMK00105 was tested using multiple low-jitter XO clock sources to evaluate the impact of the buffer’s
additive phase noise/jitter. The plots on the left show the phase noise of the clock source, while the plots on the
right show the total output phase noise from LMK00105 contributed by both the clock source noise and buffer
additive noise. Note that the phase noise “hump” around 80 kHz offset on the phase noise plots is correlated to
the XO source, which is attributed to power supply noise at this frequency.
Figure 11. Phase Noise of 125-MHz Clock Source
Figure 12. LMK00105 Clock Output
A low-noise 125 MHz XO clock source with 45.6 fs RMS jitter (Figure 11) was used to drive the LMK00105,
resulting in in a total output phase jitter of 81.6 fs RMS (Figure 12) integrated from 12 kHz to 20 MHz. The
resultant additive jitter of the buffer is 67.7 fs RMS computed using the “Square-Root of the Difference of
Squares” method.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
15
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
Typical Applications (continued)
Figure 13. Phase Noise of 100-MHz Clock Source
Figure 14. LMK00105 Clock Output
A low-noise 100 MHz XO clock source with 43.5 fs RMS jitter (Figure 13) was used to drive the LMK00105,
resulting in a total output phase jitter of 103.1 fs RMS (Figure 14) integrated from 12 kHz to 20 MHz. The
resultant additive jitter of the buffer is 93.4 fs RMS computed using the “Square-Root of the Difference of
Squares” method.
Figure 15. Phase Noise of 50-MHz Clock Source
Figure 16. LMK00105 Clock Output
A divide-by-2 circuit was used with the low-noise 100-MHz XO to generate a 50-MHz clock source with 174.9fs
RMS jitter (Figure 15), resulting in a total output phase jitter of 201.6 fs RMS (Figure 16) integrated from 12 kHz
to 20 MHz.
In this case, the total output phase noise/jitter is highly correlated to the clock source phase noise and jitter,
which prevents us from computing the true additive jitter of the buffer using the “Square-Root of the Difference of
Squares” method. To accurately specify the additive jitter of the buffer at this frequency, a clock source with
lower noise (compared to the DUT) would be needed for this measurement.
16
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
Typical Applications (continued)
Figure 17. Phase Noise of 25-MHz Clock Source
Figure 18. LMK00105 Clock Output
A divide-by-4 circuit was used with the low-noise 100 MHz XO to generate a 25-MHz clock source with 134.5 fs
RMS (Figure 17), resulting in a total output phase jitter of 138.2 fs RMS (Figure 18) integrated from 12 kHz to 5
MHz.
In this case, the total output phase noise and jitter is highly correlated to the clock source phase noise and jitter,
which prevents us from computing the true additive jitter of the buffer using the “Square-Root of the Difference of
Squares” method. To accurately specify the additive jitter of the buffer at this frequency, a clock source with
lower noise (compared to the DUT) would be needed for this measurement.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
17
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
Typical Applications (continued)
8.2.2 Crystal Interface
C1
OSCin
XTAL
RLIM
OSCout
LMK00105
The LMK00105 has an integrated crystal oscillator circuit that supports a fundamental mode, AT-cut crystal. The
crystal interface is shown in Figure 19.
C2
Figure 19. Crystal Interface
8.2.2.1 Design Requirements
The value of capacitor and resistor depend on the crystal. Each crystal is specified with a load capacitance and
resistor is used to avoid over driving the crystal.
The example crystal specifications are given in Table 5.
Table 5. Example 25-MHz Crystal Electrical Specifications
NO.
ITEM
SYMBOL
ELECTRICAL SPECIFICATION
MIN
F0
TYP
MAX
25
UNIT
1
Nominal Frequency
MHz
2
Mode of Vibration
3
Frequency Tolerance
4
Load Capacitance
CL
9
5
Drive Level
DL
6
Equivalent Series Resistance
R1
7
Shunt Capacitance
C0
2.1 ± 15%
pF
8
Motional Capacitance
C1
9.0 ± 15%
fF
Fundamental
ΔF/F0
9
Motional Inductance
L
10
Frequency Stability
TC
11
C0/C1 Rate
–15
15
ppm
100
300
µW
9
50
pF
4.6 ± 15%
–20
Ω
mH
20
ppm
250
Based on the OSCin shunt capacitance and stray capacitance, C1 and C2 are chosen as 6.8 pF to make the
load capacitance (CL) to be 9 pF. Suggested value of RLIM is 1.5 kΩ. Refer to Detailed Design Procedure for the
derivation.
8.2.2.2 Detailed Design Procedure
The load capacitance (CL) is specific to the crystal, but usually on the order of 18 to 20 pF. While CL is specified
for the crystal, the OSCin input capacitance (CIN = 1 pF typical) of the device and PCB stray capacitance (CSTRAY
~ 1 to 3 pF) can affect the discrete load capacitor values, C1 and C2. For the parallel resonant circuit, the discrete
capacitor values can be calculated as follows:
CL = (C1 * C2) / (C1 + C2) + CIN + CSTRAY
(1)
Typically, C1 = C2 for optimum symmetry, so Equation 1 can be rewritten in terms of C1only:
CL = C12 / (2 * C1) + CIN + CSTRAY
(2)
Finally, solve for C1:
C1 = (CL - CIN - CSTRAY) * 2
18
(3)
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
Electrical Characteristics provides crystal interface specifications with conditions that ensure start-up of the
crystal, but it does not specify crystal power dissipation. The designer will need to ensure the crystal power
dissipation does not exceed the maximum drive level specified by the crystal manufacturer. Overdriving the
crystal can cause premature aging, frequency shift, and eventual failure. Drive level should be held at a sufficient
level necessary to start-up and maintain steady-state operation.
The power dissipated in the crystal, PXTAL, can be computed by:
PXTAL = IRMS2 * RESR * (1 + C0 / CL)2
(4)
Where:
• IRMS is the RMS current through the crystal.
• RESR is the maximum equivalent series resistance specified for the crystal.
• CL is the load capacitance specified for the crystal.
• C0 is the minimum shunt capacitance specified for the crystal.
IRMS can be measured using a current probe (e.g. Tektronix CT-6 or equivalent) placed on the leg of the crystal
connected to OSCout with the oscillation circuit active.
As shown in Figure 19, an external resistor, RLIM, can be used to limit the crystal drive level if necessary. If the
power dissipated in the selected crystal is higher than the drive level specified for the crystal with RLIM shorted,
then a larger resistor value is mandatory to avoid overdriving the crystal. However, if the power dissipated in the
crystal is less than the drive level with RLIM shorted, then a zero value for RLIM can be used. As a starting point, a
suggested value for RLIM is 1.5 kΩ.
Figure 20 shows the LMK00105 output phase noise performance in crystal mode with the 25-MHz crystal
specified in Table 5.
8.2.2.3 Application Curves
Figure 20. Output Phase Noise in Crystal Mode with 25-MHz Crystal
(230.6 fs RMS jitter, 12 kHz to 5 MHz)
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
19
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
9 Power Supply Recommendations
9.1 Power Supply Filtering
It is recommended, but not required, to insert a ferrite bead between the board power supply and the chip power
supply to isolate the high-frequency switching noises generated by the clock driver, preventing them from leaking
into the board supply. Choosing an appropriate ferrite bead with very low DC resistance is important, because it
is imperative to provide adequate isolation between the board supply and the chip supply. It is also imperative to
maintain a voltage at the supply terminals that is greater than the minimum voltage required for proper operation.
Figure 21. Power-Supply Decoupling
9.2 Power Supply Ripple Rejection
In practical system applications, power supply noise (ripple) can be generated from switching power supplies,
digital ASICs or FPGAs, etc. While power supply bypassing will help filter out some of this noise, it is important to
understand the effect of power supply ripple on the device performance. When a single-tone sinusoidal signal is
applied to the power supply of a clock distribution device, such as LMK00105, it can produce narrow-band phase
modulation as well as amplitude modulation on the clock output (carrier). In the singleside band phase noise
spectrum, the ripple-induced phase modulation appears as a phase spur level relative to the carrier (measured in
dBc).
For the LMK00105, power supply ripple rejection (PSRR), was measured as the single-sideband phase spur
level (in dBc) modulated onto the clock output when a ripple signal was injected onto the Vddo supply. The PSRR
test setup is shown in Figure 22.
Ripple
Source
Vcco
Clock
Source
Power
Supplies
Bias-Tee
IN+
IC
IN-
Vcc
OUT
Limiting
Amp
DUT Board
OUT
Phase Noise
Analyzer
Scope
Measure 100 mVPP
ripple on Vcco at IC
Measure single
sideband phase spur
power in dBc
Figure 22. PSRR Test Setup
A signal generator was used to inject a sinusoidal signal onto the Vddo supply of the DUT board, and the peak-topeak ripple amplitude was measured at the Vddo pins of the device. A limiting amplifier was used to remove
amplitude modulation on the differential output clock and convert it to a single-ended signal for the phase noise
analyzer. The phase spur level measurements were taken for clock frequencies of 100 MHz under the following
power supply ripple conditions:
20
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
Power Supply Ripple Rejection (continued)
•
•
Ripple amplitude: 100 mVpp on Vddo = 2.5 V
Ripple frequency: 100 kHz
Assuming no amplitude modulation effects and small index modulation, the peak-to-peak deterministic jitter (DJ)
can be calculated using the measured single-sideband phase spur level (PSRR) as follows:
DJ (ps pk-pk) = [(2 * 10(PSRR/20)) / (π * fclk)] * 1012
(5)
9.3 Power Supply Bypassing
The Vdd and Vddo power supplies should have a high frequency bypass capacitor, such as 100 pF, placed very
close to each supply pin. Placing the bypass capacitors on the same layer as the LMK00105 improves input
sensitivity and performance. All bypass and decoupling capacitors should have short connections to the supply
and ground plane through a short trace or via to minimize series inductance.
10 Layout
10.1 Layout Guidelines
10.1.1 Ground Planes
Solid ground planes are recommended as they provide a low-impedance return paths between the device and its
bypass capacitors and its clock source and destination devices. Avoid return paths of other system circuitry (for
example, high-speed/digital logic) from passing through the local ground of the device to minimize noise
coupling, which could induce added jitter and spurious noise.
10.1.2 Power Supply Pins
Follow the power supply schematic and layout example described in Power Supply Bypassing.
10.1.3 Differential Input Termination
• Place input termination resistors as close as possible to the CLKin/CLKin* pins.
• Avoid or minimize vias in the 50-Ω input traces to minimize impedance discontinuities. Intra-pair skew should
be also be minimized on the differential input traces.
• If not used, CLKin/CLKin* inputs may be left floating.
10.1.4 Output Termination
• Place series termination resistors as close as possible to the CLKoutX outputs at the launch of the controlled
impedance traces.
• Avoid or minimize vias in the 50-Ω traces to minimize impedance discontinuities.
• Any unused CLKoutX output should be left floating and not routed.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
21
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
10.2 Layout Example
2.6 mm, min
0.2 mm, typ
1.0 mm,
typ
Figure 23. Recommended Land and Via Pattern
10.3 Thermal Management
For reliability and performance reasons the die temperature should be limited to a maximum of 125°C. That is, as
an estimate, TA (ambient temperature) plus device power consumption times θJA should not exceed 125°C.
The package of the device has an exposed pad that provides the primary heat removal path as well as excellent
electrical grounding to a printed circuit board. To maximize the removal of heat from the package a thermal land
pattern including multiple vias to a ground plane must be incorporated on the PCB within the footprint of the
package. The exposed pad must be soldered down to ensure adequate heat conduction out of the package.
A recommended land and via pattern is shown in Figure 23. More information on soldering WQFN packages and
gerber footprints can be obtained: www.ti.com/packaging.
To minimize junction temperature it is recommended that a simple heat sink be built into the PCB (if the ground
plane layer is not exposed). This is done by including a copper area of about 2 square inches on the opposite
side of the PCB from the device. This copper area may be plated or solder coated to prevent corrosion but
should not have conformal coating (if possible), which could provide thermal insulation. The vias shown in
Figure 23 should connect these top and bottom copper layers and to the ground layer. These vias act as “heat
pipes” to carry the thermal energy away from the device side of the board to where it can be more effectively
dissipated.
22
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
LMK00105
www.ti.com
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Differential Voltage Measurement Terminology
The differential voltage of a differential signal can be described by two different definitions causing confusion
when reading datasheets or communicating with other engineers. This section will address the measurement and
description of a differential signal so that the reader will be able to understand and discern between the two
different definitions when used.
The first definition used to describe a differential signal is the absolute value of the voltage potential between the
inverting and noninverting signal. The symbol for this first measurement is typically VID or VOD depending on if an
input or output voltage is being described.
The second definition used to describe a differential signal is to measure the potential of the noninverting signal
with respect to the inverting signal. The symbol for this second measurement is VSS and is a calculated
parameter. Nowhere in the IC does this signal exist with respect to ground, it only exists in reference to its
differential pair. VSS can be measured directly by oscilloscopes with floating references, otherwise this value can
be calculated as twice the value of VOD as described in the first section
Figure 24 illustrates the two different definitions side-by-side for inputs and Figure 25 illustrates the two different
definitions side-by-side for outputs. The VID and VOD definitions show VA and VB DC levels that the noninverting
and inverting signals toggle between with respect to ground. VSS input and output definitions show that if the
inverting signal is considered the voltage potential reference, the noninverting signal voltage potential is now
increasing and decreasing above and below the noninverting reference. Thus the peak-to-peak voltage of the
differential signal can be measured.
VID and VOD are often defined in volts (V) and VSS is often defined as volts peak-to-peak (VPP).
VID Definition
VSS Definition for Input
Noninverting Clock
VIH
VCM
VSS
VID
VIL
Inverting Clock
VID = | VIH ± VIL |
VSS = 2·VID
GND
Figure 24. Two Different Definitions for Differential Input Signals
VOD Definition
VSS Definition for Output
Noninverting Clock
VOH
VOS
VOL
VSS
VOD
Inverting Clock
VOD = | VOH - VOL |
VSS = 2·VOD
GND
Figure 25. Two Different Definitions for Differential Output Signals
11.2 Trademarks
All trademarks are the property of their respective owners.
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
23
LMK00105
SNAS579G – MARCH 2012 – REVISED DECEMBER 2014
www.ti.com
11.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
24
Submit Documentation Feedback
Copyright © 2012–2014, Texas Instruments Incorporated
Product Folder Links: LMK00105
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2014
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LMK00105SQ/NOPB
ACTIVE
WQFN
RTW
24
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
K00105
LMK00105SQE/NOPB
ACTIVE
WQFN
RTW
24
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
K00105
LMK00105SQX/NOPB
ACTIVE
WQFN
RTW
24
4500
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 85
K00105
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2014
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Oct-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
LMK00105SQ/NOPB
WQFN
RTW
24
LMK00105SQE/NOPB
WQFN
RTW
LMK00105SQX/NOPB
WQFN
RTW
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
1000
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
24
250
178.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
24
4500
330.0
12.4
4.3
4.3
1.3
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
9-Oct-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMK00105SQ/NOPB
WQFN
RTW
24
1000
210.0
185.0
35.0
LMK00105SQE/NOPB
WQFN
RTW
24
250
210.0
185.0
35.0
LMK00105SQX/NOPB
WQFN
RTW
24
4500
367.0
367.0
35.0
Pack Materials-Page 2
MECHANICAL DATA
RTW0024A
SQA24A (Rev B)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated