AME 600mA CMOS LDO AME8806 / 8809 / 8842 n General Description The AME8806/8809/8842 family of positive, linear regulators feature low quiescent current (30µA typ.) with low dropout voltage, making them ideal for battery applications. The space-saving SOP-8 package is attractive for "Pocket" and "Hand Held" applications. These rugged devices have both Thermal Shutdown, and Current Fold-back to prevent device failure under the "Worst" of operating conditions. In applications requiring a low noise, regulated supply, place a 1000 pF capacitor between Bypass and ground. n Functional Block Diagram IN OUT Overcurrent Shutdown Thermal Shutdown EN BYP R1 AMP The AME8806/8809/8842 is stable with an output capacitance of 2.2µF or greater. n Features R2 Vref=1.215V GND l Very Low Dropout Voltage l Guaranteed 600mA Output l Accurate to within 1.5% n Typical Application l 30µA Quiescent Current l Over-Temperature Shutdown INPUT OUTPUT AME8806 AME8809 l Current Limiting l Short Circuit Current Fold-back BYP l Noise Reduction Bypass Capacitor l Power-Saving Shutdown Mode OUT IN 5V l Space-Saving SOP-8 Package EN GND C1 C2 C3 1µF 1000pF 2.2µF l Factory Pre-set Output Voltages l Low Temperature Coefficient l All AME's Lead Free Products Meet RoHS Standards n Applications INPUT PG l Portable Electronics l Cordless Phones OUTPUT AME8842 l Instrumentation l Wireless Devices OUT IN 5V GND EN C1 C3 1µF 2.2µF l PC Peripherals l Battery Powered Widgets l Electronic Scales Rev.H.02 1 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Pin Configuration SOP-8 Top View 8 7 6 5 AME8806 SOP-8 Top View AME8806 8 7 6 5 1. EN 2. GND 2. IN 3. GND AME8809 2 3 4 3. OUT 4. EN 4. BYP 5. BYP 5. GND 6. GND 1 AME8809 1. IN 7. GND 6. GND 1 2 3 4 7. GND 8. OUT 8. GND * Die Attach: * Die Attach: Conductive Epoxy Conductive Epoxy SOP-8 Top View 8 7 6 5 AME8842 1. PG 2. IN AME8842 3. OUT 4. EN 5. GND 6. GND 1 2 3 4 7. GND 8. GND * Die Attach: Non-Conductive Epoxy 2 Rev.H.02 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Ordering Information AME8806 x x x x x AME8809 x x x x x AME8842 x x x x x Special Feature Number of Pins Package Type Operating Ambient Temperature Range Product Grade or Option Product Grade or Option A: B: C: D: E: F: G: H: I: J: K: L: M: N: O: P: Q: R: S: U: V: W: Y: Z: Rev.H.02 3.3V 3.0V 2.8V 2.5V 3.8V 3.6V 3.5V 2.7V 3.4V 2.85V 3.7V 1.5V 1.8V 2.9V 3.1V 4.1V 4.75V 2.65V 5.0V 3.2V 3.15V 2.3V 1.9V 1.7V 1: 2: 3: 4: 1.3V 2.0V 4.2V 4.0V Operating Ambient Temperature Range E: -40OC to +85OC Package Type H: SOP Number of Pins A: 8 Special Feature Z: Lead Free 3 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Ordering Information Part Number AME8806AEHA AME8806AEHAZ AME8806BEHA AME8806BEHAZ AME8806CEHA AME8806CEHAZ AME8806DEHA AME8806DEHAZ AME8806EEHA Marking* 8806 AEHA yyww 8806 AEHA yyww 8806 BEHA yyww 8806 BEHA yyww 8806 CEHA yyww 8806 CEHA yyww 8806 DEHA yyww 8806 DEHA yyww 8806 EEHA yyww Output Voltage Package Operating Ambient Temperature Range 3.3V SOP-8 - 40oC to +85oC 3.3V SOP-8 - 40oC to +85oC 3.0V SOP-8 - 40oC to +85oC 3.0V SOP-8 - 40oC to +85oC 2.8V SOP-8 - 40oC to +85oC 2.8V SOP-8 - 40oC to +85oC 2.5V SOP-8 - 40oC to +85oC 2.5V SOP-8 - 40oC to +85oC 3.8V SOP-8 - 40oC to +85oC AME8806EEHAZ 8806 EEHA yyww 3.8V SOP-8 - 40oC to +85oC AME8806FEHA 8806 FEHA yyww 3.6V SOP-8 - 40oC to +85oC AME8806FEHAZ 8806 FEHA yyww 3.6V SOP-8 - 40oC to +85oC Note: yyww represents the date code * A line on top of the first letter represents lead free plating such as 8806 Please consult AME sales office or authorized Rep./Distributor for output voltage and package type availability. 4 Rev.H.02 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Ordering Information (contd.) Part Number AME8806GEHA AME8806GEHAZ AME8806HEHA AME8806HEHAZ AME8806IEHA AME8806IEHAZ AME8806JEHA AME8806JEHAZ AME8806KEHA AME8806KEHAZ AME8806LEHA AME8806LEHAZ AME8806MEHA AME8806MEHAZ Rev.H.02 Marking* 8806 GEHA yyww 8806 GEHA yyww 8806 HEHA yyww 8806 HEHA yyww 8806 IEHA yyww 8806 IEHA yyww 8806 JEHA yyww 8806 JEHA yyww 8806 KEHA yyww 8806 KEHA yyww 8806 LEHA yyww 8806 LEHA yyww 8806 MEHA yyww 8806 MEHA yyww Output Voltage Package Operating Ambient Temperature Range 3.5V SOP-8 - 40oC to +85oC 3.5V SOP-8 - 40oC to +85oC 2.7V SOP-8 - 40oC to +85oC 2.7V SOP-8 - 40oC to +85oC 3.4V SOP-8 - 40oC to +85oC 3.4V SOP-8 - 40oC to +85oC 2.85V SOP-8 - 40oC to +85oC 2.85V SOP-8 - 40oC to +85oC 3.7V SOP-8 - 40oC to +85oC 3.7V SOP-8 - 40oC to +85oC 1.5V SOP-8 - 40oC to +85oC 1.5V SOP-8 - 40oC to +85oC 1.8V SOP-8 - 40oC to +85oC 1.8V SOP-8 - 40oC to +85oC 5 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Ordering Information (contd.) Part Number AME8806NEHA AME8806NEHAZ AME8806OEHA AME8806OEHAZ AME8809AEHA AME8809AEHAZ AME8809BEHA AME8809BEHAZ AME8809CEHA AME8809CEHAZ AME8809DEHA AME8809DEHAZ AME8809EEHA AME8809EEHAZ 6 Marking* 8806 NEHA yyww 8806 NEHA yyww 8806 OEHA yyww 8806 OEHA yyww 8809 AEHA yyww 8809 AEHA yyww 8809 BEHA yyww 8809 BEHA yyww 8809 CEHA yyww 8809 CEHA yyww 8809 DEHA yyww 8809 DEHA yyww 8809 EEHA yyww 8809 EEHA yyww Output Voltage Package Operating Ambient Temperature Range 2.9V SOP-8 - 40oC to +85oC 2.9V SOP-8 - 40oC to +85oC 3.1V SOP-8 - 40oC to +85oC 3.1V SOP-8 - 40oC to +85oC 3.3V SOP-8 - 40oC to +85oC 3.3V SOP-8 - 40oC to +85oC 3.0V SOP-8 - 40oC to +85oC 3.0V SOP-8 - 40oC to +85oC 2.8V SOP-8 - 40oC to +85oC 2.8V SOP-8 - 40oC to +85oC 2.5V SOP-8 - 40oC to +85oC 2.5V SOP-8 - 40oC to +85oC 3.8V SOP-8 - 40oC to +85oC 3.8V SOP-8 - 40oC to +85oC Rev.H.02 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Ordering Information (contd.) Part Number AME8809FEHA AME8809FEHAZ AME8809GEHA AME8809GEHAZ AME8809HEHA AME8809HEHAZ AME8809IEHA AME8809IEHAZ AME8809JEHA AME8809JEHAZ AME8809KEHA AME8809KEHAZ AME8809LEHA AME8809LEHAZ Rev.H.02 Marking* 8809 FEHA yyww 8809 FEHA yyww 8809 GEHA yyww 8809 GEHA yyww 8809 HEHA yyww 8809 HEHA yyww 8809 IEHA yyww 8809 IEHA yyww 8809 JEHA yyww 8809 JEHA yyww 8809 KEHA yyww 8809 KEHA yyww 8809 LEHA yyww 8809 LEHA yyww Output Voltage Package Operating Ambient Temperature Range 3.6V SOP-8 - 40oC to +85oC 3.6V SOP-8 - 40oC to +85oC 3.5V SOP-8 - 40oC to +85oC 3.5V SOP-8 - 40oC to +85oC 2.7V SOP-8 - 40oC to +85oC 2.7V SOP-8 - 40oC to +85oC 3.4V SOP-8 - 40oC to +85oC 3.4V SOP-8 - 40oC to +85oC 2.85V SOP-8 - 40oC to +85oC 2.85V SOP-8 - 40oC to +85oC 3.7V SOP-8 - 40oC to +85oC 3.7V SOP-8 - 40oC to +85oC 1.5V SOP-8 - 40oC to +85oC 1.5V SOP-8 - 40oC to +85oC 7 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Ordering Information (contd.) Part Number AME8809MEHA AME8809MEHAZ AME8809NEHA AME8809NEHAZ AME8809OEHA AME8809OEHAZ AME8842AEHA AME8842AEHAZ AME8842BEHA AME8842BEHAZ AME8842CEHA AME8842CEHAZ AME8842DEHA AME8842DEHAZ 8 Marking* 8809 MEHA yyww 8809 MEHA yyww 8809 NEHA yyww 8809 NEHA yyww 8809 OEHA yyww 8809 OEHA yyww 8842 AEHA yyww 8842 AEHA yyww 8842 BEHA yyww 8842 BEHA yyww 8842 CEHA yyww 8842 CEHA yyww 8842 DEHA yyww 8842 DEHA yyww Output Voltage Package Operating Ambient Temperature Range 1.8V SOP-8 - 40oC to +85oC 1.8V SOP-8 - 40oC to +85oC 2.9V SOP-8 - 40oC to +85oC 2.9V SOP-8 - 40oC to +85oC 3.1V SOP-8 - 40oC to +85oC 3.1V SOP-8 - 40oC to +85oC 3.3V SOP-8 - 40oC to +85oC 3.3V SOP-8 - 40oC to +85oC 3.0V SOP-8 - 40oC to +85oC 3.0V SOP-8 - 40oC to +85oC 2.8V SOP-8 - 40oC to +85oC 2.8V SOP-8 - 40oC to +85oC 2.5V SOP-8 - 40oC to +85oC 2.5V SOP-8 - 40oC to +85oC Rev.H.02 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Ordering Information (contd.) Part Number AME8842EEHA AME8842EEHAZ AME8842FEHA AME8842FEHAZ AME8842GEHA AME8842GEHAZ AME8842HEHA AME8842HEHAZ AME8842IEHA AME8842IEHAZ AME8842JEHA AME8842JEHAZ AME8842KEHA AME8842KEHAZ Rev.H.02 Marking* 8842 EEHA yyww 8842 EEHA yyww 8842 FEHA yyww 8842 FEHA yyww 8842 GEHA yyww 8842 GEHA yyww 8842 HEHA yyww 8842 HEHA yyww 8842 IEHA yyww 8842 IEHA yyww 8842 JEHA yyww 8842 JEHA yyww 8842 KEHA yyww 8842 KEHA yyww Output Voltage Package Operating Ambient Temperature Range 3.8V SOP-8 - 40oC to +85oC 3.8V SOP-8 - 40oC to +85oC 3.6V SOP-8 - 40oC to +85oC 3.6V SOP-8 - 40oC to +85oC 3.5V SOP-8 - 40oC to +85oC 3.5V SOP-8 - 40oC to +85oC 2.7V SOP-8 - 40oC to +85oC 2.7V SOP-8 - 40oC to +85oC 3.4V SOP-8 - 40oC to +85oC 3.4V SOP-8 - 40oC to +85oC 2.85V SOP-8 - 40oC to +85oC 2.85V SOP-8 - 40oC to +85oC 3.7V SOP-8 - 40oC to +85oC 3.7V SOP-8 - 40oC to +85oC 9 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Ordering Information (contd.) Part Number AME8842LEHA AME8842LEHAZ AME8842MEHA AME8842MEHAZ AME8842NEHA AME8842NEHAZ AME8842OEHA AME8842OEHAZ 10 Marking* 8842 LEHA yyww 8842 LEHA yyww 8842 MEHA yyww 8842 MEHA yyww 8842 NEHA yyww 8842 NEHA yyww 8842 OEHA yyww 8842 OEHA yyww Output Voltage Package Operating Ambient Temperature Range 1.5V SOP-8 - 40oC to +85oC 1.5V SOP-8 - 40oC to +85oC 1.8V SOP-8 - 40oC to +85oC 1.8V SOP-8 - 40oC to +85oC 2.9V SOP-8 - 40oC to +85oC 2.9V SOP-8 - 40oC to +85oC 3.1V SOP-8 - 40oC to +85oC 3.1V SOP-8 - 40oC to +85oC Rev.H.02 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Absolute Maximum Ratings Parameter Maximum Unit 8 V P D / (V IN - VO) A GND - 0.3 to V IN + 0.3 V Input Voltage Output Current Input, Output Voltage B* ESD Classification Caution: Stress above the listed absolute maximum rating may cause permanent damage to the device. *HBM B: 2000V~3999V n Recommended Operating Conditions Parameter Symbol Rating Unit Ambient Temperature Range TA - 40 to +85 o Junction Temperature Range TJ - 40 to +125 o C C n Thermal Information Parameter Package Die Attach Symbol Conductive Epoxy Thermal Resistance (Junction to Case) *SOP-8 Non-Conductive Epoxy SOP-8 Non-Conductive Epoxy θJA SOP-8 Non-Conductive Epoxy o C/W o C/W N/A 150 θJC N/A Conductive Epoxy Internal Power Dissipation Unit 60 Conductive Epoxy Thermal Resistance (Junction to Ambient) Maximum 810 PD mW N/A Maximum Junction Temperature 150 o C Solder Iron(10 Sec)** 350 o C * Measure θJC on center of molding compound if IC has no tab. ** MIL-STD-202G 210F Rev.H.02 11 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Electrical Specifications TA = 25OC unless otherwise noted Parameter Symbol Input Voltage V IN Output Voltage Accuracy VO Test Condition IO =1mA Min Typ Max Units Note 1 7 V -1.5 1.5 % 1.3V<=V O(NOM)<=1.4V Dropout Voltage V DROPOUT IO=600mA 1.4V<V O(NOM)<=2.0V V O =V O(NOM) -2.0% 2.0V<V O(NOM)<=2.8V 1900 See chart 2.8V<V O(NOM) 1400 mV 800 600 IO V O >1.2V 600 Current Limit ILIM V O >1.2V 600 Short Circuit Current ISC V O <0.8V 300 600 mA Quiescent Current IQ IO =0mA 30 50 µA Ground Pin Current IGND IO =1mA to 600mA 35 Output Current Line Regulation Load Regulation Over Temperature Shutdown Over Temperature Hysterisis V O Temperature Coefficient Power Supply Rejection Output Voltage Noise REG LINE REGLOAD mA 800 mA µA 1.3V <= V O <= 1.4V -0.2 0.2 IO =1mA 1.4V < V O <= 2.0V -0.15 0.15 V IN =V O+1 to V O +2 2.0V <= V O < 4.0V -0.1 0.02 0.1 V O >= 4.0V -0.4 0.2 0.4 0.2 1 IO =1mA to 600mA % % 150 o C OTH 30 o C TC 30 OTS PSRR eN IO =100mA f=1kHz 75 CO =2.2µF ceramic f=10kHz 55 CB Y P=0.01 µF f=100kHz 30 f=10Hz to 100kHz IO =10mA, Co=2.2µF 30 ppm/o C dB µVrms CB Y P=0.01 µF V EH V IN =2.7V to 7V 2.0 Vin V V EL V IN =2.7V to 7V 0 0.4 V IEH V EN =V IN , V IN =2.7V to 7V 0.1 µA IEL V EN =0V, V IN =2.7V to 7V 0.5 µA Shutdown Supply Current ISD V IN =5V, V O=0V, V EN <V EL 1 µA PG Leakage Current ILC V PG =7V 1 µA PG Voltage Rating V PG V O in regulation 7 V PG Voltage Low V OL ISINK=0.4mA 0.4 V EN Input Threshold EN Input Bias Current 12 0.5 Note1:VIN(min)=VOUT+VDROPOUT Note2: To prevent the Short Circuit Current protection feature from being prematurely activated, the input voltage must be applied before a current source load is applied. Rev.H.02 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Detailed Description The AME8806/8809/8842 family of CMOS regulators contain a PMOS pass transistor, voltage reference, error amplifier, over-current protection, and thermal shutdown. The P-channel pass transistor receives data from the error amplifier, over-current shutdown, and thermal protection circuits. During normal operation, the error amplifier compares the output voltage to a precision reference. Over-current and Thermal shutdown circuits become active when the junction temperature exceeds 150oC, or the current exceeds 600mA. During thermal shutdown, the output voltage remains low. Normal operation is restored when the junction temperature drops below 120oC. All capacitors should be placed in close proximity to the pins. A "Quiet" ground termination is desirable. This can be achieved with a "Star" connection. n Enable The Enable pin normally floats high. When actively, pulled low, the PMOS pass transistor shuts off, and all internal circuits are powered down. In this state, the quiescent current is less than 1µA. This pin behaves much like an electronic switch. The AME8806/8809/8842 switches from voltage mode to current mode when the load exceeds the rated output current. This prevents over-stress. The AME8806/8809/ 8842 also incorporates current foldback to reduce power dissipation when the output is short circuited. This feature becomes active when the output drops below 0.8 volts, and reduces the current flow by 65%. Full current is restored when the voltage exceeds 0.8 volts. n External Capacitors The AME8806/8809/8842 is stable with an output capacitor to ground of 2.2µF or greater. Ceramic capacitors have the lowest ESR, and will offer the best AC performance. Conversely, Aluminum Electrolytic capacitors exhibit the highest ESR, resulting in the poorest AC response. Unfortunately, large value ceramic capacitors are comparatively expensive. One option is to parallel a 0.1µF ceramic capacitor with a 10µF Aluminum Electrolytic. The benefit is low ESR, high capacitance, and low overall cost. A second capacitor is recommended between the input and ground to stabilize Vin. The input capacitor should be at least 0.1µF to have a beneficial effect. A third capacitor can be connected between the BYPASS pin and GND. This capacitor can be a low cost Polyester Film variety between the value of 0.001 ~ 0.01µF. A larger capacitor improves the AC ripple rejection, but also makes the output come up slowly. This "Soft" turn-on is desirable in some applications to limit turn-on surges. Rev.H.02 13 AME 600mA CMOS LDO AME8806 / 8809 / 8842 Ground Current vs. Input Voltage Load Step (1mA-600mA) 45 Vo(10mV/DIV) 85 OC 35 30 25 O Output CL=2.2µF CIN=2.2µF 25 C 20 IL(200mA/DIV) Ground Current (µ A) 40 15 10 5 0 0 1 2 3 4 5 6 7 ILoad 0 8 TIME (20mS/DIV) Input Voltage (V) Drop Out Voltage vs. Output Voltage Power Supply Rejection Ratio 0 1200 ILOAD=600mA 800 600 400 100mA CL=2.2µF Tantalum Tantalum C BYP =0 -20 PSRR (dB) Drop Out Voltage (mV) -10 1000 -30 -40 -50 10mA 100mA -60 200 -70 100 µ A 100 µ A 1mA -80 0 1 2 3 4 5 10 6 1K Output Voltage (V) 100K 10M Frequency (Hz) Safe Operating Area Power Supply Rejection Ratio -20 100mA 600 PSRR (dB) Output Current (mA) -30 100 1mA -40 -50 100mA -60 -70 10 0.1 1.0 Input-Output Voltage Differential (V) 14 CL=2.2µF Tantalum CBYP=1000pF 8.0 -80 10 10mA 100µA 100µA 1K 100K 10M Frequency (Hz) Rev.H.02 AME 600mA CMOS LDO AME8806 / 8809 / 8842 Overtemperature Shutdown I OUT (200mA/DIV) Vo (1mV DIV) Noise Measurement TIME (20ms/DIV) Short Circuit Response IOUT (200mV/DIV) VOUT (1V/DIV) VOUT (1V/DIV) CLOAD=2.2µF CIN=1µF RLOAD<100mΩ TIME (2mS/DIV) Chip Enable Transient Response Line Transient Response CL=2µF RL=10Ω 0 0 TIME (1mS/DIV) VIN(1V/DIV) TIME (2mS/DIV) VOUT (10mV/DIV) IOUT (200mA/DIV) CLOAD=2.2µF CIN=1.0µF RLOAD=3.3Ω VOUTNOM=3.3V Output (1V/DIV) Enable (2V/DIV) 0 TIME (0.5Sec/DIV) Current Limit Response Rev.H.02 0 R LOAD=6.6 Ω VOUT (1V/DIV) CL=2.2µF No Filter CLOAD=2.2µF ILOAD=1mA VOUTDC=3.3V VINDC=4.5V TIME (200mS/DIV) 15 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Tape and Reel Dimension SOP-8 P PIN 1 W AME AME Carrier Tape, Number of Components Per Reel and Reel Size 16 Package Carrier Width (W) Pitch (P) Part Per Full Reel Reel Size SOP-8 12.0±0.1 mm 4.0±0.1 mm 2500pcs 330±1 mm Rev.H.02 AME 600mA CMOS LDO AME8806 / 8809 / 8842 n Package Dimension SOP-8 Side View Top View SYMBOLS C E H PIN 1 θ D MAX MIN MAX A 1.35 1.75 0.05315 0.0689 A1 0.10 0.30 0.00394 0.01181 1.473 REF 0.33 0.51 0.01299 0.02008 C 0.19 0.25 0.00748 0.00984 D 4.80 5.33 0.18898 0.20984 E 3.80 4.00 0.14961 0.15748 1.27 BSC e A 0.05000 BSC L 0.40 1.27 0.01575 0.05000 H 5.80 6.30 0.22835 0.24803 y - 0.10 θ 0 o 8 o 0 o 0.00394 8o A1 A2 7o(4X) 0.05799 REF B e Front View INCHES MIN A2 L MILLIMETERS B Rev.H.02 17 www.ame.com.tw E-Mail: [email protected] Life Support Policy: These products of AME, Inc. are not authorized for use as critical components in life-support devices or systems, without the express written approval of the president of AME, Inc. AME, Inc. reserves the right to make changes in the circuitry and specifications of its devices and advises its customers to obtain the latest version of relevant information. AME, Inc. , November 2008 Document: 2006/2095-DS8806/8809/8842-H.02 Corporate Headquarter AME, Inc. 2F, 302 Rui-Guang Road, Nei-Hu District Taipei 114, Taiwan. Tel : 886 2 2627-8687 Fax: 886 2 2659-2989