ML145151 ML145152 ML145155 ML145156 ML145157 ML145158 PLL Frequency Synthesizer Family - CMOS The devices described in this document are typically used as low–power, phase–locked loop frequency synthesizers. When combined with an external low–pass filter and voltage–controlled oscillator, these devices can provide all the remaining functions for a PLL frequency synthesizer operating up to the device's frequency limit. For higher VCO frequency operation, a down mixer or a prescaler can be used between the VCO and the synthesizer IC. These frequency synthesizer chips can be found in the following and other applications: CATV TV Tuning AM/FM Radios Scanning Receivers Two–Way Radios Amateur Radio ÷R OSC φ CONTROL LOGIC ÷N ÷A ÷ P/P + 1 VCO EXTERNAL COMPONENTS OUTPUT FREQUENCY CONTENTS Page DEVICE DETAIL SHEETS ML145151 Parallel–Input, Single–Modulus ...........................................................................................2 ML145152 Parallel–Input, Dual–Modulus..............................................................................................5 ML145155 Serial–Input, Single–Modulus ..............................................................................................9 ML145156 Serial–Input, Dual–Modulus...............................................................................................13 ML145157 Serial–Input, Single–Modulus ............................................................................................17 ML145158 Serial–Input, Dual–Modulus...............................................................................................20 FAMILY CHARACTERISTICS Maximum Ratings..................................................................................................................................23 DC Electrical Characteristics.................................................................................................................23 AC Electrical Characteristics.................................................................................................................25 Timing Requirements.............................................................................................................................26 Frequency Characteristics ......................................................................................................................27 Phase Detector/Lock Detector Output Waveforms................................................................................27 DESIGN CONSIDERATIONS Phase–Locked Loop – Low–Pass Filter Design ....................................................................................28 Crystal Oscillator Considerations ..........................................................................................................29 Dual–Modulus Prescaling......................................................................................................................30 Page 1 of 35 www.lansdale.com Issue A ML145151 Parallel-Input PLL Frequency Synthesizer Interfaces with Single–Modulus Prescalers Legacy Device: Motorola/Freescale MC145151 The ML145151 is programmed by 14 parallel–input data lines for the N counter and three input lines for the R counter. The device features consist of a reference oscillator, selectable–reference divider, digital–phase detector, and 14–bit programmable divide–by–N counter. • Operating Temperature Range: TA = – 40 to 85°C • Low Power Consumption Through Use of CMOS Technology • 3.0 to 9.0 V Supply Range • On– or Off–Chip Reference Oscillator Operation • Lock Detect Signal • ÷ N Counter Output Available • Single Modulus/Parallel Programming • 8 User–Selectable ÷ R Values: 8, 128, 256, 512, 1024, 2048, 2410, 8192 • ÷ N Range = 3 to 16383 • “Linearized” Digital Phase Detector Enhances Transfer Function Linearity • Two Error Signal Options: Single–Ended (Three–State) or Double–Ended • Chip Complexity: 8000 FETs or 2000 Equivalent Gates Page 2 of 35 www.lansdale.com P DIP 28 = YP PLASTIC DIP CASE 710 28 1 SO 28W = -6P SOG PACKAGE CASE 751F 28 1 CROSS REFERENCE/ORDERING INFORMATION PACKAGE MOTOROLA LANSDALE P DIP 28 MC145151P2 ML145151YP SO 28W MC145151DW2 ML145151-6P Note: Lansdale lead free (Pb) product, as it becomes available, will be identified by a part number prefix change from ML to MLE. PIN ASSIGNMENT fin 1 28 LD VSS 2 27 OSCin VDD 3 26 OSCout PDout 4 25 N11 RA0 5 24 N10 RA1 6 23 N13 RA2 7 22 N12 φR 8 21 T/R φV 9 20 N9 fV 10 19 N8 N0 11 18 N7 N1 12 17 N6 N2 13 16 N5 N3 14 15 N4 Issue A LANSDALE Semiconductor, Inc. ML145151 ML145151 BLOCK DIAGRAM RA2 RA1 RA0 OSCout 14 x 8 ROM REFERENCE DECODER LOCK DETECT 14 LD 14–BIT ÷ R COUNTER OSCin PHASE DETECTOR A PDout 14–BIT ÷ N COUNTER fin VDD PHASE DETECTOR B 14 TRANSMIT OFFSET ADDER T/R φV φR fV N13 N11 N9 N7 N6 N4 N2 N0 NOTE: N0 – N13 inputs and inputs RA0, RA1, and RA2 have pull–up resistors that are not shown. PIN DESCRIPTIONS INPUT PINS f in Frequency Input (Pin 1) Input to the ÷N portion of the synthesizer. f in is typically derived from loop VCO and is AC coupled into the device. For larger amplitude signals (standard CMOS logic levels) DC coupling may be used. RA0 – RA2 Reference Address Inputs (Pins 5, 6, 7) These three inputs establish a code defining one of eight possible divide values for the total reference divider, as defined by the table below. Pull–up resistors ensure that inputs left open remain at a logic 1 and require only a SPST switch to alter data to the zero state. RA2 RA1 RA0 Total Divide Value 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 8 128 256 512 1024 2048 2410 8192 Reference Address Code N0 – N11 N Counter Programming Inputs (Pins 11 – 20, 22 – 25) These inputs provide the data that is preset into the ÷ N counter when it reaches the count of zero. N0 is the least sig- Page 3 of 35 nificant and N13 is the most significant. Pull–up resistors ensure that inputs left open remain at a logic 1 and require only an SPST switch to alter data to the zero state. T/R Transmit/Receive Offset Adder Input (Pin 21) This input controls the offset added to the data provided at the N inputs. This is normally used for offsetting the VCO frequency by an amount equal to the IF frequency of the transceiver. This offset is fixed at 856 when T/R is low and gives no offset when T/R is high. A pull–up resistor ensures that no connection will appear as a logic 1 causing no offset addition. OSCin, OSCout Reference Oscillator Input/Output (Pins 27, 26) These pins form an on–chip reference oscillator when connected to terminals of an external parallel resonant crystal. Frequency setting capacitors of appropriate value must be connected from OSCin to ground and OSCout to ground. OSCin may also serve as the input for an externally generated reference signal. This signal is typically AC coupled to OSCin, but for larger amplitude signals (standard CMOS logic levels) DC coupling may also be used. In the external reference mode, no connection is required to OSCout. OUTPUT PINS PDout Phase Detector A Output (Pin 4) Three–state output of phase detector for use as loop–error signal. Double–ended outputs are also available for this purpose (see ΦV and ΦR). Frequency fV > fR or fV Leading: Negative Pulses Frequency fV < fR or fV Lagging: Positive Pulses Frequency fV = fR and Phase Coincidence: High–Impedance State www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145151 φR,φV Phase Detector B Outputs (Pins 8, 9) These phase detector outputs can be combined externally for a loop–error signal. A single–ended output is also available for this purpose (see PDout). If frequency fV is greater than fR or if the phase of fV is leading, then error information is provided by φV pulsing low. φR remains essentially high. If the frequency fV is less than fR or if the phase of fV is lagging, then error information is provided by φR pulsing low. φV remains essentially high. If the frequency of fV = fR and both are in phase, then both φV and φR remain high except for a small minimum time period when both pulse low in phase. fV N Counter Output (Pin 10) This is the buffered output of the ÷ N counter that is inter- nally connected to the phase detector input. With this output available, the ÷ N counter can be used independently. LD Lock Detector Output (Pin 28) Essentially a high level when loop is locked (fR, fV of same phase and frequency). Pulses low when loop is out of lock. POWER SUPPLY VDD Positive Power Supply (Pin 3) The positive power supply potential. This pin may range from + 3 to + 9 V with respect to VSS. VSS Negative Power Supply (Pin 2) The most negative supply potential. This pin is usuallyground. TYPICAL APPLICATIONS 2.048 MHz OSCin OSCout fin NC NC RA2 RA1 RA0 ML145151 VOLTAGE CONTROLLED OSCILLATOR PDout N13 N12 N11 N10 N9 N8 N7 N6 N5 N4 N3 N2 N1 N0 5 – 5.5 MHz 0 1 1 1 0 0 0 1 0 0 0 = 5 MHz 1 0 1 0 1 1 1 1 1 0 0 = 5.5 MHz Figure 1. 5 MHz to 5.5 MHz Local Oscillator Channel Spacing = 1 kHz LOCK DETECT SIGNAL “1” OSCout RA2 +V REF. OSC. 10.0417 MHz (ON–CHIP OSC. OPTIONAL) OSCin VDD VSS “1” “0” RA1 RA0 LD ML145151 T/R fV PDout φR fV fin CHOICE OF DETECTOR ERROR SIGNALS LOOP FILTER T: 13.0833 – 18.0833 MHz R: 9.5167 – 14.5167 MHz TRANSMIT (ADDS 856 TO ÷ N VALUE) VCO X6 T: 73.3333 – 78.3333 MHz R: 69.7667 – 74.7667 MHz DOWN MIXER “0” “0” “1” RECEIVE TRANSMIT: 440.0 – 470.0 MHz RECEIVE: 418.6 – 448.6 MHz (25 kHz STEPS) CHANNEL PROGRAMMING ÷ N = 2284 TO 3484 X6 60.2500 MHz NOTES: 1. fR = 4.1667 kHz; ÷ R = 2410; 21.4 MHz low side injection during receive. 2. Frequency values shown are for the 440 – 470 MHz band. Similar implementation applies to the 406 – 440 MHz band. For 470 – 512 MHz, consider reference oscillator frequency X9 for mixer injection signal (90.3750 MHz). Figure 2. Synthesizer for Land Mobile Radio UHF Bands ML145151 Data Sheet Continued on Page 23 Page 4 of 35 www.lansdale.com Issue A ML145152 Parallel-Input PLL Frequency Synthesizer Interfaces with Dual–Modulus Prescalers Legacy Device: Motorola/Freescale MC145152 The ML145152 is programmed by sixteen parallel inputs for the N and A counters and three input lines for the R counter. The device features consist of a reference oscillator, selectable–reference divider, two–output phase detector, 10–bit programmable divide–by–N counter, and 6–bit programmable ÷ A counter. • Operating Temperature Range: TA = – 40 to 85°C • Low Power Consumption Through Use of CMOS Technology • 3.0 to 9.0 V Supply Range • On– or Off–Chip Reference Oscillator Operation • Lock Detect Signal • Dual Modulus/Parallel Programming • 8 User–Selectable ÷ R Values: 8, 64, 128, 256, 512, 1024, 1160, 2048 • ÷ N Range = 3 to 1023, ÷ A Range = 0 to 63 • Chip Complexity: 8000 FETs or 2000 Equivalent Gates • See Application Note AN980 Page 5 of 35 www.lansdale.com P DIP 28 = YP PLASTIC DIP CASE 710 28 1 SO 28W = -6P SOG PACKAGE CASE 751F 28 1 CROSS REFERENCE/ORDERING INFORMATION PACKAGE MOTOROLA LANSDALE P DIP 28 MC145152P2 ML145152YP SO 28W MC145152DW2 ML145152-6P Note: Lansdale lead free (Pb) product, as it becomes available, will be identified by a part number prefix change from ML to MLE. PIN ASSIGNMENT fin 1 28 LD VSS 2 27 OSCin VDD 3 26 OSCout RA0 4 25 A4 RA1 5 24 A3 RA2 6 23 A0 φR 7 22 A2 φV 8 21 A1 MC 9 20 N9 A5 10 19 N8 N0 11 18 N7 N1 12 17 N6 N2 13 16 N5 N3 14 15 N4 Issue A LANSDALE Semiconductor, Inc. ML145152 ML145152 BLOCK DIAGRAM RA2 RA1 RA0 OSCout 12 x 8 ROM REFERENCE DECODER 12 LOCK DETECT 12–BIT ÷ R COUNTER OSCin LD MC CONTROL LOGIC PHASE DETECTOR φV φR fin 6–BIT ÷ A COUNTER A5 A3 A2 A0 10–BIT ÷ N COUNTER N0 N2 N4 N5 N7 N9 NOTE: N0 – N9, A0 – A5, and RA0 – RA2 have pull–up resistors that are not shown. PIN DESCRIPTIONS INPUT PINS f in Frequency Input (Pin 1) Input to the positive edge triggered ÷ N and ÷ A counters. f in is typically derived from a dual–modulus prescaler and is AC coupled into the device. For larger amplitude signals (standard CMOS logic levels) DC coupling may be used. RA0, RA1, RA2 Reference Address Inputs (Pins 4, 5, 6) These three inputs establish a code defining one of eight possible divide values for the total reference divider. The total reference divide values are as follows: RA2 RA1 RA0 Total Divide Value 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 8 64 128 256 512 1024 1160 2048 Reference Address Code N0 – N9 N Counter Programming Inputs (Pins 11 – 20) The N inputs provide the data that is preset into the ÷ N counter when it reaches the count of 0. N0 is the least significant digit and N9 is the most significant. Pull–up resistors ensure that inputs left open remain at a logic 1 and require only a SPST switch to alter data to the zero state. A0 – A5 A Counter Programming Inputs(Pins 23, 21, 22, 24, 25, 10) The A inputs define the number of clock cycles of f in that require a logic 0 on the MC output (see Dual–Modulus Prescaling section). The A inputs all have internal pull–up resisPage 6 of 35 tors that ensure that inputs left open will remain at a logic 1. OSCin, OSCout Reference Oscillator Input/Output (Pins 27, 26) These pins form an on–chip reference oscillator when connected to terminals of an external parallel resonant crystal. Frequency setting capacitors of appropriate value must be connected from OSCin to ground and OSCout to ground. OSCin may also serve as the input for an externally generated reference signal. This signal is typically AC coupled to OSCin, but for larger amplitude signals (standard CMOS logic levels) DC coupling may also be used. In the external reference mode, no connection is required to OSCout. OUTPUT PINS φR,φV Phase Detector B Outputs (Pins 7, 8) These phase detector outputs can be combined externally for a loop–error signal. If the frequency fV is greater than fR or if the phase of fV is leading, then error information is provided by φV pulsing low. φR remains essentially high. If the frequency fV is less than fR or if the phase of fV is lagging, then error information is provided by φR pulsing low. φV remains essentially high. If the frequency of fV = fR and both are in phase, then both φV and φR remain high except for a small minimum time period when both pulse low in phase. MC Dual–Modulus Prescale Control Output (Pin 9) Signal generated by the on–chip control logic circuitry for controlling an external dual–modulus prescaler. The MC level will be low at the beginning of a count cycle and will remain low until the ÷ A counter has counted down from its programmed value. At this time, MC goes high and remains high until the ÷ N counter has counted the rest of the way down from its programmed value (N – A additional counts since both ÷ N and ÷ A are counting down during the first portion of the cycle). MC is then set back low, the counters preset to www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145152 their respective programmed values, and the above sequence repeated. This provides for a total programmable divide value (NT)=N•P+A where P and P + 1 represent the dual–modulus prescaler divide values respectively for high and low MC levels, N the number programmed into the ÷ N counter, and A the number programmed into the ÷ A counter. LD Lock Detector Output (Pin 28) Essentially a high level when loop is locked (fR, fV of same phase and frequency). Pulses low when loop is out of lock. POWER SUPPLY VDD Positive Power Supply (Pin 3) The positive power supply potential. This pin may range from + 3 to + 9 V with respect to VSS. VSS Negative Power Supply (Pin 2) The most negative supply potential. This pin is usuallyground. TYPICAL APPLICATIONS NO CONNECTS “1” “1” “1” LOCK DETECT SIGNAL 10.24 MHz NOTE 1 R2 OSCout RA2 RA1 RA0 LD φR OSCin φV ML145152 +V VDD MC VSS fin N9 N0 A5 C 150 – 175 MHz 5 kHz STEPS R1 – R1 + R2 VCO MC33171 NOTE 2 C A0 ML12017 ÷ 64/65 PRESCALER CHANNEL PROGRAMMING NOTES: 1. Off–chip oscillator optional. 2. The φR and φV outputs are fed to an external combiner/loop filter. See the Phase–Locked Loop — Low–Pass Filter Design page for additional information. The φR and φV outputs swing rail–to–rail. Therefore, the user should be careful not to exceed the common mode input range of the op amp used in the combiner/loop filter. Figure 1. Synthesizer for Land Mobile Radio VHF Bands Page 7 of 35 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. REF. OSC. 15.360 MHz (ON–CHIP OSC. OPTIONAL) ML145152 RECEIVER 2ND L.O. 30.720 MHz NO CONNECTS X2 “1” “1” “1” R2 OSCout RA2 RA1 RA0 +V VDD VSS N9 LD φR OSCin ML145152 NOTE 5 φV MC fin N0 A5 RECEIVER FIRST L.O. 825.030 → 844.980 MHz (30 kHz STEPS) LOCK DETECT SIGNAL C R1 – R1 + R2 X4 NOTE 6 VCO NOTE 7 C A0 TRANSMITTER MODULATION ML12017 ÷ 64/65 PRESCALER NOTE 6 CHANNEL PROGRAMMING X4 NOTE 6 TRANSMITTER SIGNAL 825.030 → 844.980 MHz (30 kHz STEPS) NOTES: 1. Receiver 1st I.F. = 45 MHz, low side injection; Receiver 2nd I.F. = 11.7 MHz, low side injection. 2. Duplex operation with 45 MHz receiver/transmit separation. 3. fR = 7.5 kHz; ÷ R = 2048. 4. Ntotal = N 64 + A = 27501 to 28166; N = 429 to 440; A = 0 to 63. 5. ML145158 may be used where serial data entry is desired. 6. High frequency prescalers may be used for higher frequency VCO and f ref implementations. 7. The φR and φV outputs are fed to an external combiner/loop filter. See the Phase–Locked Loop — Low–Pass Filter Design page for additional information. The φR and φV outputs swing rail–to–rail. Therefore, the user should be careful not to exceed the common mode input range of the op amp used in the combiner/loop filter. Figure 2. 666–Channel, Computer–Controlled, Mobile Radiotelephone Synthesizer for 800 MHz Cellular Radio Systems ML145152 Data Sheet Continued on Page 23 Page 8 of 35 www.lansdale.com Issue A ML145155 Serial–Input PLL Frequency Synthesizer Interfaces with Single–Modulus Prescalers Legacy Device: Motorola/Freescale MC145155-2 The ML145155 is programmed by a clocked, serial input, 16–bit data stream. The device features consist of a reference oscillator, selectable–reference divider, digital–phase detector, 14–bit programmable divide–by–N counter, and the necessary shift register and latch circuitry for accepting serial input data. • Operating Temperature Range: TA = – 40 to 85°C • Low Power Consumption Through Use of CMOS Technology • 3.0 to 9.0 V Supply Range • On– or Off–Chip Reference Oscillator Operation with Buffered Output • Compatible with the Serial Peripheral Interface (SPI) on CMOS MCUs • Lock Detect Signal • Two Open–Drain Switch Outputs • 8 User–Selectable ÷ R Values: 16, 512, 1024, 2048, 3668, 4096, 6144, 8192 • Single Modulus/Serial Programming • ÷ N Range = 3 to 16383 • “Linearized” Digital Phase Detector Enhances Transfer Function Linearity • Two Error Signal Options: Single–Ended (Three–State) or Double–Ended • Chip Complexity: 6504 FETs or 1626 Equivalent Gates P DIP 18 = VP PLASTIC DIP CASE 707 18 1 20 1 SOG 20W = -6P SOG PACKAGE CASE 751D CROSS REFERENCE/ORDERING INFORMATION MOTOROLA LANSDALE PACKAGE P DIP 18 MC145155P2 ML145155VP SOG 20W MC145155DW2 ML145155-6P Note: Lansdale lead free (Pb) product, as it becomes available, will be identified by a part number prefix change from ML to MLE. PIN ASSIGNMENTS SOG PACKAGE PLASTIC DIP RA1 1 18 RA0 RA1 1 20 RA0 RA2 2 17 OSCin RA2 2 19 OSCin φV 3 16 OSCout φV 3 18 OSCout φR 4 15 REFout φR 4 17 REFout VDD 5 14 SW2 VDD 5 16 NC PDout 6 13 SW1 PDout 6 15 SW2 VSS 7 12 ENB VSS 7 14 SW1 LD 8 11 DATA NC 8 13 ENB fin 9 10 CLK LD 9 12 DATA fin 10 11 CLK NC = NO CONNECTION Page 9 of 35 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145155 ML145155 BLOCK DIAGRAM RA2 RA1 RA0 14 x 8 ROM REFERENCE DECODER LOCK DETECT 14 OSCout LD 14–BIT ÷ R COUNTER OSCin fR fV REFout fin PHASE DETECTOR A PDout 14–BIT ÷ R COUNTER 14 VDD PHASE DETECTOR B φV φR SW2 ENB LATCH LATCH SW1 14 DATA 14–BIT SHIFT REGISTER 2–BIT SHIFT REGISTER CLK RA0, RA1, RA2 Reference Address Inputs (PDIP – Pins 18, 1, 2; SOG – Pins 20, 1, 2) These three inputs establish a code defining one of eight possible divide values for the total reference divider, as defined by the table below: RA2 RA1 RA0 Total Divide Value 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 16 512 1024 2048 3668 4096 6144 8192 Reference Address Code CLK, DATA Shift Register Clock, Serial Data Inputs (PDIP – Pins 10, 11; SOG – Pins 11, 12) Each low–to–high transition clocks one bit into the on–chip 16–bit shift register. The Data input provides programming information for the 14–bit ÷ N counter and the two switch Page 10 of 35 signals SW1 and SW2. The entry format is as follows: SW1 SW2 ÷ N MSB ÷ N COUNTER BITS ÷ N LSB PIN DESCRIPTIONS INPUT PINS f in Frequency Input (PDIP – Pin 9, SOG – Pin 10) Input to the ÷ N portion of the synthesizer. f in is typically derived from loop VCO and is AC coupled into the device. For larger amplitude signals (standard CMOS logic levels) DC coupling may be used. LAST DATA BIT IN (BIT NO. 16) FIRST DATA BIT IN (BIT NO. 1) ENB Latch Enable Input (PDIP – Pin 12, SOG – Pin 13) When high (1), ENB transfers the contents of the shift register into the latches, and to the programmable counter inputs, and the switch outputs SW1 and SW2. When low (0), ENB inhibits the above action and thus allows changes to be made in the shift register data without affecting the counter programming and switch outputs. An on–chip pull–up establishes a continuously high level for ENB when no external signal is applied. ENB is normally low and is pulsed high to transfer data to the latches. OSCin, OSCout Reference Oscillator Input/Output (PDIP – Pins 17, 16; SOG – Pins 19, 18) These pins form an on–chip reference oscillator when connected to terminals of an external parallel resonant crystal. Frequency setting capacitors of appropriate value must be connected from OSCin to ground and OSCout to ground. OSCin may also serve as the input for an externally–generated reference signal. This signal is typically ac coupled to OSCin, but for larger amplitude signals (standard CMOS logic levels) DC coupling may also be used. In the external reference mode, no connection is required to OSCout. www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145155 ML145155 OUTPUT PINS PDout Phase Detector A Output (PDIP, SOG – Pin 6) Three–state output of phase detector for use as loop error signal. Double–ended outputs are also available for this purpose (see φV and φR). Frequency fV > fR or fV Leading: Negative Pulses Frequency fV < fR or fV Lagging: Positive Pulses Frequency fV = fR and Phase Coincidence: High–Impedance State φR, φV Phase Detector B Outputs (PDIP, SOG – Pins 4, 3) These phase detector outputs can be combined externally for a loop–error signal. A single–ended output is also available for this purpose (see PDout). If frequency fV is greater than fR or if the phase of fV is leading, then error information is provided by fV pulsing low. fR remains essentially high. If the frequency fV is less than fR or if the phase of fV is lagging, then error information is provided by fR pulsing low. fV remains essentially high. If the frequency of fV = fR and both are in phase, then both fV and fR remain high except for a small minimum time period when both pulse low in phase. LD Lock Detector Output (PDIP – Pin 8, SOG – Pin 9) Essentially a high level when loop is locked (fR, fV of same phase and frequency). LD pulses low when loop is out of lock. SW1, SW2 Band Switch Outputs (PDIP – Pins 13, 14; SOG – Pins 14, 15) SW1 and SW2 provide latched open–drain outputs corresponding to data bits numbers one and two. These outputs can be tied through external resistors to voltages as high as 15 V, independent of the VDD supply voltage. These are typically used for band switch functions. A logic 1 causes the output to assume a high–impedance state, while a logic 0 causes the output to be low. REFout Buffered Reference Oscillator Output (PDIP, SOG – Pin 15) Buffered output of on–chip reference oscillator or externally provided reference–input signal. POWER SUPPLY VDD Positive Power Supply (PDIP, SOG – Pin 5) The positive power supply potential. This pin may range from + 3 to + 9 V with respect to VSS. VSS Negative Power Supply (PDIP, SOG – Pin 7) The most negative supply potential. This pin is usually ground. TYPICAL APPLICATIONS 4.0 MHz UHF/VHF TUNER OR CATV FRONT END MC120xx PRESCALER fin DATA KEYBOARD ML145155 CLK φR φV – + 1/2 MC1458* ENB CMOS MPU/MCU 3 MC14489 LED DISPLAY * The φR and φV outputs are fed to an external combiner/loop filter. See the Phase–Locked Loop – Low–Pass Filter Design page for additional information. The φR and φV outputs swing rail–to–rail. Therefore, the user should be careful not to exceed the common mode input range of the op amp used in the combiner/loop filter. Figure 1. Microprocessor–Controlled TV/CATV Tuning System with Serial Interface Page 11 of 35 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145155 ML145155 2.56 MHz FM OSC ML12019 ÷20 PRESCALER AM OSC fin DATA KEYBOARD φR φV ML145155 CLK – + 1/2 MC1458* TO AM/FM OSCILLATORS ENB CMOS MPU/MCU TO DISPLAY * The φR and φV outputs are fed to an external combiner/loop filter. See the Phase–Locked Loop – Low–Pass Filter Design page for additional information. The φR and φV outputs swing rail–to–rail. Therefore, the user should be careful not to exceed the common mode input range of the op amp used in the combiner/loop filter. Figure 2. AM/FM Radio Synthesizer Page 12 of 35 www.lansdale.com Issue A ML145156 Serial–Input PLL Frequency Synthesizer Interfaces with Dual–Modulus Prescalers Legacy Device: Motorola/Freescale MC145156-2 The ML145156 is programmed by a clocked, serial input, 19–bit data stream. The device features consist of a reference oscillator, selectable–reference divider, digital–phase detector, 10–bit programmable divide–by–N counter, 7–bit programmable divide–by–A counter, and the necessary shift register and latch circuitry for accepting serial input data. • Operating Temperature Range: TA = – 40 to 85°C • Low Power Consumption Through Use of CMOS Technology • 3.0 to 9.0 V Supply Range • On– or Off–Chip Reference Oscillator Operation with Buffered Output • Compatible with the Serial Peripheral Interface (SPI) on CMOS MCUs • Lock Detect Signal • Two Open–Drain Switch Outputs • Dual Modulus/Serial Programming • 8 User–Selectable ÷ R Values: 8, 64, 128, 256, 640, 1000, 1024, 2048 • ÷ N Range = 3 to 1023, ÷A Range = 0 to 127 • “Linearized” Digital Phase Detector Enhances Transfer Function Linearity • Two Error Signal Options: Single–Ended (Three–State) or Double–Ended • Chip Complexity: 6504 FETs or 1626 Equivalent Gates Page 13 of 35 www.lansdale.com P DIP 20 = RP PLASTIC DIP CASE 738 20 1 SOG 20W = -6P SOG PACKAGE CASE 751D 20 1 CROSS REFERENCE/ORDERING INFORMATION LANSDALE MOTOROLA PACKAGE P DIP 20 MC145156P2 ML145156RP SOG 20W MC145156DW2 ML145156-6P Note: Lansdale lead free (Pb) product, as it becomes available, will be identified by a part number prefix change from ML to MLE. PIN ASSIGNMENT RA1 1 20 RA0 RA2 2 19 OSCin φV 3 18 OSCout φR 4 17 REFout VDD 5 16 TEST PDout 6 15 SW2 VSS 7 14 SW1 MC 8 13 ENB LD 9 12 DATA fin 10 11 CLK Issue A LANSDALE Semiconductor, Inc. ML145156 ML145156 BLOCK DIAGRAM RA2 RA1 RA0 12 x 8 ROM REFERENCE DECODER 12 LOCK DETECT 12–BIT ÷ R COUNTER OSCin LD OSCout fR CONTROL LOGIC REFout fV MC 7–BIT ÷ A COUNTER fin 10–BIT ÷ N COUNTER ÷ ENB A COUNTER LATCH ÷ PDout φV φR SW2 LATCH N COUNTER LATCH 7 DATA PHASE DETECTOR B 10 7 VDD PHASE DETECTOR A SW1 10 7–BIT SHIFT REGISTER 2–BIT SHIFT REGISTER 10–BIT SHIFT REGISTER CLK RA2 RA1 RA0 Total Divide Value 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 8 64 128 256 640 1000 1024 2048 Reference Address Code CLK, DATA Shift Register Clock, Serial Data Inputs (Pins 11, 12) Each low–to–high transition clocks one bit into the on–chip 19–bit shift register. The data input provides programming information for the 10–bit ÷ N counter, the 7–bit ÷ A counter, and the two switch signals SW1 and SW2. The entry format is as follows: Page 14 of 35 SW1 SW2 ÷A ÷ RA0, RA1, RA2 Reference Address Inputs (Pins 20, 1, 2) These three inputs establish a code defining one of eight possible divide values for the total reference divider, as defined by the table below: ÷ f in Frequency Input (Pin 10) Input to the positive edge triggered ÷ N and ÷ A counters. f in is typically derived from a dual–modulus prescaler and is AC coupled into the device. For larger amplitude signals (standard CMOS logic levels), DC coupling may be used. N COUNTER BITS MSB N LSB A COUNTER BITS ÷N MSB PIN DESCRIPTIONS A LSB INPUT PINS LAST DATA BIT IN (BIT NO. 19) FIRST DATA BIT IN (BIT NO. 1) ENB Latch Enable Input (Pin 13) When high (1), ENB transfers the contents of the shift register into the latches, and to the programmable counter inputs, and the switch outputs SW1 and SW2. When low (0), ENB inhibits the above action and thus allows changes to be made in the shift register data without affecting the counter programming and switch outputs. An on–chip pull–up establishes a continuously high level for ENB when no external signal is applied. ENB is normally low and is pulsed high to transfer data to the latches. OSCin, OSCout Reference Oscillator Input/Output (Pins 19, 18) These pins form an on–chip reference oscillator when connected to terminals of an external parallel resonant crystal. Frequency setting capacitors of appropriate value must be connected from OSCin to ground and OSCout to ground. OSCin may also serve as the input for an externally–generated reference signal. This signal is typically AC coupled to OSCin, but for larger amplitude signals (standard CMOS logic levels) DC coupling may also be used. In the external reference mode, no connection is required to OSCout. TEST Factory Test Input (Pin 16) Used in manufacturing. Must be left open or tied to VSS. www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145156 ML145156 OUTPUT PINS PDout Phase Detector A Output (Pin 6) Three–state output of phase detector for use as loop–error signal. Double–ended outputs are also available for this purpose (see φV and φR). Frequency fV > fR or fV Leading: Negative Pulses Frequency fV < fR or fV Lagging: Positive Pulses Frequency fV = fR and Phase Coincidence: High–Impedance State respective programmed values, and the above sequence repeated. This provides for a total programmable divide value (NT) = N • P + A where P and P + 1 represent the dual–modulus prescaler divide values respectively for high and low MC levels, N the number programmed into the ÷ N counter, and A the number programmed into the ÷ A counter. LD Lock Detector Output (Pin 9) Essentially a high level when loop is locked (fR, fV of same phase and frequency). LD pulses low when loop is out of lock. φR, φV Phase Detector B Outputs (Pins 4, 3) These phase detector outputs can be combined externally for a loop–error signal. A single–ended output is also available for this purpose (see PDout). If frequency fV is greater than fR or if the phase of fV is leading, then error information is provided by φV pulsing low. φR remains essentially high. If the frequency fV is less than fR or if the phase of fV is lagging, then error information is provided by φR pulsing low. φV remains essentially high. If the frequency of fV = fR and both are in phase, then both φV and φR remain high except for a small minimum time period when both pulse low in phase. SW1, SW2 Band Switch Outputs (Pins 14, 15) SW1 and SW2 provide latched open–drain outputs corresponding to data bits numbers one and two. These outputs can be tied through external resistors to voltages as high as 15 V, independent of the VDD supply voltage. These are typically used for band switch functions. A logic 1 causes the output to assume a high–impedance state, while a logic 0 causes the output to be low. MC Dual–Modulus Prescale Control Output (Pin 8) Signal generated by the on–chip control logic circuitry forcontrolling an external dual–modulus prescaler. The MC levelwill be low at the beginning of a count cycle and will remainlow until the ÷ A counter has counted down from its programmed value. At this time, MC goes high and remains highuntil the ÷ N counter has counted the rest of the way downfrom its programmed value (N – A additional counts since both ÷ N and ÷ A are counting down during the first portion of the cycle). MC is then set back low, the counters preset to their POWER SUPPLY Page 15 of 35 REFout Buffered Reference Oscillator Output (Pin 17) Buffered output of on–chip reference oscillator or externally provided reference–input signal. VDD Positive Power Supply (Pin 5) The positive power supply potential. This pin may range from + 3 to + 9 V with respect to VSS. VSS Negative Power Supply (Pin 7) The most negative supply potential. This pin is usuallyground. www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145156 ML145156 TYPICAL APPLICATIONS + 12 V LOCK DETECT SIGNAL 3.2 MHz NOTES 1 AND 2 +V OSCin OSCout RA2 RA1 RA0 LD SW1 SW2 PDout VDD ML145156 VSS REFout KEY– BOARD CLK DATA φR fin ENB FM B + + 12 V AM B + OPTIONAL LOOP ERROR SIGNAL – VCO φV MC + 1/2 MC1458 NOTE 3 CMOS MPU/MCU ML12019 ÷ 20/21 DUAL MODULUS PRESCALER TO DISPLAY DRIVER (e.g., MC14489) NOTES: 1. For AM: channel spacing = 5 kHz, ÷ R = ÷ 640 (code 100). 2. For FM: channel spacing = 25 kHz, ÷ R = ÷ 128 (code 010). 3. The φR and φV outputs are fed to an external combiner/loop filter. See the Phase–Locked Loop – Low–Pass Filter Design page for additional information. The φR and φV outputs swing rail–to–rail. Therefore, the user should be careful not to exceed the common mode input range of the op amp used in the combiner/loop filter. Figure 1. AM/FM Radio Broadcast Synthesizer 3.2 MHz (NOTE 3) NAV = 01 COM = 10 +V OSCin OSCout RA2 RA1 RA0 VDD REFout R/T LD SW1 SW2 PDout ML145156 VSS CLK DATA ENB fin VCO RANGE NAV: 97.300 – 107.250 MHz COM–T: 118.000 – 135.975 MHz COM–R: 139.400 – 157.375 MHz LOCK DETECT SIGNAL MC φR – φV + VCO MC33171 NOTE 5 CMOS MPU/MCU ML12016 (NOTES 2 AND 4) ÷ 40/41 DUAL MODULUS PRESCALER CHANNEL SELECTION TO DISPLAY DRIVER (e.g., MC14489) NOTES: 1. For NAV: fR = 50 kHz, ÷ R = 64 using 10.7 MHz lowside injection, N total = 1946 – 2145. For COM–T: fR = 25 kHz, ÷ R = 128, Ntotal = 4720 – 5439. For COM–R: f R = 25 kHz, ÷ R = 128, using 21.4 MHz highside injection, Ntotal = 5576 – 6295. 2. A ÷ 32/33 dual modulus approach is provided by substituting an ML12015 for the ML12016. The devices are pin equivalent. 3. A 6.4 MHz oscillator crystal can be used by selecting ÷ R = 128 (code 010) for NAV and ÷ R = 256 (code 011) for COM. . 4. ML12013 + MC10131 combination may also be used to form the ÷ 40/41 prescaler 5. The φR and φV outputs are fed to an external combiner/loop filter. See the Phase–Locked Loop – Low–Pass Filter Design page for additional information. The φR and φV outputs swing rail–to–rail. Therefore, the user should be careful not to exceed the common mode input range of the op amp used in the combiner/loop filter. Figure 2. Avionics Navigation or Communication Synthesizer ML145156 Data Sheet Continued on Page 23 Page 16 of 35 www.lansdale.com Issue A ML145157 Serial–Input PLL Frequency Synthesizer Interfaces with Single–Modulus Prescalers Legacy Device: Motorola/Freescale MC145157-2 The ML145157 has a fully programmable 14–bit reference counter, as well as a fully programmable ÷ N counter. The counters are programmed serially through a common data input and latched into the appropriate counter latch, according to the last data bit (control bit) entered. • Operating Temperature Range: TA = – 40 to 85°C • Low Power Consumption Through Use of CMOS Technology • 3.0 to 9.0 V Supply Range • Fully Programmable Reference and ÷ N Counters • ÷ R Range = 3 to 16383 • ÷ N Range = 3 to 16383 • fV and fR Outputs • Lock Detect Signal • Compatible with the Serial Peripheral Interface (SPI) on CMOS MCUs • “Linearized” Digital Phase Detector • Single–Ended (Three–State) or Double–Ended Phase Detector Outputs • Chip Complexity: 6504 FETs or 1626 Equivalent Gates Page 17 of 35 www.lansdale.com P DIP 16 = EP PLASTIC DIP CASE 648 16 1 SOG 16 = -5P SOG PACKAGE CASE 751G 16 1 CROSS REFERENCE/ORDERING INFORMATION PACKAGE MOTOROLA LANSDALE P DIP 16 MC145157P2 ML145157EP SOG 20W MC145157DW2 ML145157-5P Note: Lansdale lead free (Pb) product, as it becomes available, will be identified by a part number prefix change from ML to MLE. PIN ASSIGNMENT OSCin 1 16 φR OSCout 2 15 φV fV 3 14 REFout VDD 4 13 fR PDout 5 12 S/Rout VSS 6 11 ENB LD 7 10 DATA fin 8 9 CLK Issue A LANSDALE Semiconductor, Inc. ML145157 ML145157 BLOCK DIAGRAM 14–BIT SHIFT REGISTER 14 ENB REFERENCE COUNTER LATCH 14 OSCin 14–BIT LOCK DETECT PHASE DETECTOR A REFout 14–BIT ÷ N COUNTER fin LD ÷ R COUNTER OSCout 14 ÷ N COUNTER LATCH DATA fR PHASE DETECTOR B PDout φV φR fV 14 1–BIT CONTROL S/R 14–BIT SHIFT REGISTER S/Rout CLK PIN DESCRIPTIONS INPUT PINS fin Frequency Input (Pin 8) Input frequency from VCO output. A rising edge signal on this input decrements the ÷ N counter. This input has an inverter biased in the linear region to allow use with AC coupled signals as low as 500 mV p–p. For larger amplitude signals (standard CMOS logic levels), DC coupling may be used. MSB LSB CONTROL CLK, DATA Shift Clock, Serial Data Inputs (Pins 9, 10) Each low–to–high transition of the clock shifts one bit of data into the on–chip shift registers. The last data bit entered determines which counter storage latch is activated; a logic 1selects the reference counter latch and a logic 0 selects the ÷ N counter latch. The entry format is as follows: FIRST DATA BIT INTO SHIFT REGISTER ENB Latch Enable Input (Pin 11) A logic high on this pin latches the data from the shift register into the reference divider or ÷ N latches depending on the control bit. The reference divider latches are activated if the control bit is at a logic high and the ÷ N latches are activated if Page 18 of 35 the control bit is at a logic low. A logic low on this pin allows the user to change the data in the shift registers without affecting the counters. ENB is normally low and is pulsed high to transfer data to the latches. OSCin, OSCout Reference Oscillator Input/Output (Pins 1, 2) These pins form an on–chip reference oscillator when connected to terminals of an external parallel resonant crystal. Frequency setting capacitors of appropriate value must be connected from OSCin to ground and OSCout to ground. OSCin may also serve as the input for an externally–generated reference signal. This signal is typically AC coupled to OSCin, but for larger amplitude signals (standard CMOS logic levels) DC coupling may also be used. In the external reference mode, no connection is required to OSCout. OUTPUT PINS PDout Single–Ended Phase Detector A Output (Pin 5) This single–ended (three–state) phase detector output produces a loop–error signal that is used with a loop filter to control a VCO. Frequency fV > fR or fV Leading: Negative Pulses Frequency fV < fR or fV Lagging: Positive Pulses Frequency fV = fR and Phase Coincidence: High–Impedance State φR, φV Double–Ended Phase Detector B Outputs (Pins 16, 15) These outputs can be combined externally for a loop–error signal. A single–ended output is also available for this purpose (see PDout). www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145157 ML145157 If frequency fV is greater than fR or if the phase of fV is leading, then error information is provided by φV pulsing low. φR remains essentially high. If the frequency fV is less than fR or if the phase of fV is lagging, then error information is provided by φR pulsing low. φV remains essentially high. If the frequency of fV = fR and both are in phase, then both φV and φR remain high except for a small minimum time period when both pulse low in phase. fR, fV RCounter Output, N Counter Output (Pins 13, 3) Buffered, divided reference and f in frequency outputs. The fR and fV outputs are connected internally to the ÷ R and ÷ N counter outputs respectively, allowing the counters to be used independently, as well as monitoring the phase detector inputs. LD Lock Detector Output (Pin 7) This output is essentially at a high level when the loop is locked (fR, fV of same phase and frequency), and pulses low when loop is out of lock. Page 19 of 35 REFout Buffered Reference Oscillator Output (Pin 14) This output can be used as a second local oscillator, reference oscillator to another frequency synthesizer, or as the system clock to a microprocessor controller. S/Rout Shift Register Output (Pin 12) This output can be connected to an external shift register to provide band switching, control information, and counter programming code checking. POWER SUPPLY VDD Positive Power Supply (Pin 4) The positive power supply potential. This pin may range from +3 to +9 V with respect to VSS. VSS Negative Power Supply (Pin 6) The most negative supply potential. This pin is usually ground. www.lansdale.com Issue A ML145158 Serial–Input PLL Frequency Synthesizer Interfaces with Dual–Modulus Prescalers Legacy Device: Motorola/Freescale MC145158-2 The ML145158 has a fully programmable 14–bit reference counter, as well as fully programmable ÷ N and ÷ A counters. The counters are programmed serially through a common data input and latched into the appropriate counter latch, according to the last data bit (control bit) entered. • Operating Temperature Range: TA = – 40 to 85°C • Low Power Consumption Through Use of CMOS Technology • 3.0 to 9.0 V Supply Range • Fully Programmable Reference and ÷ N Counters • ÷ R Range = 3 to 16383 • ÷ N Range = 3 to 1023 • Dual Modulus Capability; ÷ A Range = 0 to 127 • fV and fR Outputs • Lock Detect Signal • Compatible with the Serial Peripheral Interface (SPI) on CMOS MCUs • “Linearized” Digital Phase Detector • Single–Ended (Three–State) or Double–Ended Phase Detector Outputs • Chip Complexity: 6504 FETs or 1626 Equivalent Gates P DIP 16 = EP PLASTIC DIP CASE 648 16 1 SOG 16 = -5P SOG PACKAGE CASE 751G 16 1 CROSS REFERENCE/ORDERING INFORMATION LANSDALE MOTOROLA PACKAGE P DIP 16 MC145158P2 ML145158EP SOG 16 MC145158DW2 ML145158-5P Note: Lansdale lead free (Pb) product, as it becomes available, will be identified by a part number prefix change from ML to MLE. PIN ASSIGNMENT Page 20 of 35 www.lansdale.com OSCin 1 16 φR OSCout 2 15 φV fV 3 14 REFout VDD 4 13 fR PDout 5 12 MC VSS 6 11 ENB LD 7 10 DATA fin 8 9 CLK Issue A LANSDALE Semiconductor, Inc. ML145158 ML145158 BLOCK DIAGRAM 14–BIT SHIFT REGISTER 14 ENB fR REFERENCE COUNTER LATCH LOCK DETECT 14 14–BIT ÷ R COUNTER OSCin OSCout PHASE DETECTOR A CONTROL LOGIC REFout 7–BIT ÷ A COUNTER fin 10–BIT ÷ N COUNTER ÷ ÷ A COUNTER LATCH 7 1–BIT CONTROL S/R PHASE DETECTOR B 10 7 DATA LD N COUNTER LATCH PDout φV φR fV 10 7–BIT S/R MC 10–BIT S/R CLK CLK, DATA Shift Clock, Serial Data Inputs (Pins 9, 10) Each low–to–high transition of the CLK shifts one bit of data into the on–chip shift registers. The last data bit entered determines which counter storage latch is activated; a logic 1 selects the reference counter latch and a logic 0 selects the ÷ A, ÷ N counter latch. The data entry format is as follows: MSB LSB CONTROL ÷R FIRST DATA BIT INTO SHIFT REGISTER Page 21 of 35 MSB LSB CONTROL INPUT PINS f in Frequency Input (Pin 8) Input frequency from VCO output. A rising edge signal on this input decrements the ÷ A and ÷ N counters. This input has an inverter biased in the linear region to allow use with AC coupled signals as low as 500 mV p–p. For larger amplitude signals (standard CMOS logic levels), DC coupling may be used. ÷N MSB LSB ÷A PIN DESCRIPTIONS FIRST DATA BIT INTO SHIFT REGISTER ENB Latch Enable Input (Pin 11) A logic high on this pin latches the data from the shift register into the reference divider or ÷ N, ÷ A latches depending on the control bit. The reference divider latches are activated if the control bit is at a logic high and the ÷ N, ÷ A latches are activated if the control bit is at a logic low. A logic low on this pin allows the user to change the data in the shift registers without affecting the counters. ENB is normally low and is pulsed high to transfer data to the latches. OSCin, OSCout Reference Oscillator Input/Output (Pins 1, 2) These pins form an on–chip reference oscillator when connected to terminals of an external parallel resonant crystal. Frequency setting capacitors of appropriate value must be connected from OSCin to ground and OSCout to ground. OSCin may also serve as the input for an externally–generated reference signal. This signal is typically AC coupled to OSCin, but for larger amplitude signals (standard CMOS logic levels) DC coupling may also be used. In the external reference mode, no connection is required to OSCout. www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML145158 ML145158 OUTPUT PINS PDout Phase Detector A Output (Pin 5) This single–ended (three–state) phase detector output produces a loop–error signal that is used with a loop filter to control a VCO. Frequency fV > fR or fV Leading: Negative Pulses Frequency fV < fR or fV Lagging: Positive Pulses Frequency fV = fR and Phase Coincidence: High–Impedance State φR, φV Phase Detector B Outputs (Pins 16, 15) Double–ended phase detector outputs. These outputs can be combined externally for a loop–error signal. A single–ended output is also available for this purpose (see PDout). If frequency fV is greater than fR or if the phase of fV is leading, then error information is provided by φV pulsing low. φR remains essentially high. If the frequency fV is less than fR or if the phase of fV is lagging, then error information is provided by φR pulsing low. φV remains essentially high. If the frequency of fV = fR and both are in phase, then both φV and φR remain high except for a small minimum time period when both pulse low in phase. MC Dual–Modulus Prescaler Control Output (Pin 12) This output generates a signal by the on–chip control logic circuitry for controlling an external dual–modulus prescaler. The MC level is low at the beginning of a count cycle and remains low until the ÷ A counter has counted down from its programmed value. At this time, MC goes high and remains high until the ÷ N counter has counted the rest of the way down from its programmed value (N – A additional counts since both ÷ N and ÷ A are counting down during the first portion of the cycle). MC is then set back low, the counters preset to their respective programmed values, and the above sequence repeated. This provides for a total programmable divide value (NT) = N • P + A where P and P + 1 represent the dual–modu- Page 22 of 35 lus prescaler divide values respectively for high and low modulus control levels, N the number programmed into the ÷ N counter, and A the number programmed into the ÷ A counter. Note that when a prescaler is needed, the dual–modulus version offers a distinct advantage. The dual–modulus prescaler allows a higher reference frequency at the phase detector input, increasing system performance capability, and simplifying the loop filter design. fR, fV R Counter Output, N Counter Output (Pins 13, 3) Buffered, divided reference and fin frequency outputs. The fR and fV outputs are connected internally to the ÷ R and ÷ N counter outputs respectively, allowing the counters to be used independently, as well as monitoring the phase detector inputs. LD Lock Detector Output (Pin 7) This output is essentially at a high level when the loop is locked (fR, fV of same phase and frequency), and pulses low when loop is out of lock. REFout Buffered Reference Oscillator Output (Pin 14) This output can be used as a second local oscillator, reference oscillator to another frequency synthesizer, or as the system clock to a microprocessor controller. POWER SUPPLY VDD Positive Power Supply (Pin 4) The positive power supply potential. This pin may range from + 3 to + 9 V with respect to VSS. VSS Negative Power Supply (Pin 6) The most negative supply potential. This pin is usuallyground. www.lansdale.com # LANSDALE Semiconductor, Inc. ML1451xx ML14515X FAMILY CHARACTERISTICS AND DESCRIPTIONS - CONTINUED MAXIMUM RATINGS* (Voltages Referenced to VSS) Symbol Value Unit – 0.5 to + 10.0 V – 0.5 to VDD + 0.5 V – 0.5 to + 15 V Input or Output Current (DC or Transient), per Pin ± 10 mA IDD, ISS Supply Current, VDD or VSS Pins ± 30 mA PD Power Dissipation, per Package† 500 mW Tstg Storage Temperature – 65 to + 150 C 260 C VDD Vin, Vout Vout Iin, Iout TL Parameter DC Supply Voltage Input or Output Voltage (DC or Transient) except SW1, SW2 Output Voltage (DC or Transient), SW1, SW2 (Rpull–up = 4.7 kΩ) Lead Temperature, 1 mm from Case for 10 seconds These devices contain protection circuitry to protect against damage due to high static voltages or electric fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to these high–impedance circuits. For proper operation, Vin and Vout should be constrained to the range VSS (Vin or Vout) VDD except for SW1 and SW2. SW1 and SW2 can be tied through external resistors to voltages as high as 15 V, independent of the supply voltage. Unused inputs must always be tied to an appropriate logic voltage level (e.g., either V SS or VDD), except for inputs with pull–up devices. Unused outputs must be left open. * Maximum Ratings are those values beyond which damage to the device may occur. Functional operation should be restricted to the limits in the Electrical Characteristics tables or Pin Descriptions section. †Power Dissipation Temperature Derating: Plastic DIP: – 12 mW/ C from 65 to 85 C SOG Package: – 7 mW/ C from 65 to 85 C ELECTRICAL CHARACTERISTICS (Voltages Referenced to VSS) Symbol VDD Parameter Test Condition Power Supply Voltage Range – 40 C 25 C 85 C VDD V Min Max Min Max Min Max Unit – 3 9 3 9 3 9 V Iss Dynamic Supply Current fin = OSCin = 10 MHz, 1 V p–p AC coupled sine wave R = 128, A = 32, N = 128 3 5 9 – – – 3.5 10 30 – – – 3 7.5 24 – – – 3 7.5 24 mA ISS Quiescent Supply Current (not including pull–up current component) Vin = VDD or VSS Iout = 0 µA 3 5 9 – – – 800 1200 1600 – – – 800 1200 1600 – – – 1600 2400 3200 µA Vin Input Voltage – f in, OSCin Input AC coupled sine wave – 500 – 500 – 500 – mV p–p VIL LowLevel Input V oltage – f in, OSCin Vout Vout Vout 2.1 V 3.5 V 6.3 V Input DC coupled square wave 3 5 9 – – – 0 0 0 – – – 0 0 0 – – – 0 0 0 V VIH High–Level Input Voltage – f in, OSCin Vout Vout Vout 0.9 V 1.5 V 2.7 V Input DC coupled square wave 3 5 9 3.0 5.0 9.0 – – – 3.0 5.0 9.0 – – – 3.0 5.0 9.0 – – – V VIL Low–Level Input Voltage – except f in, OSCin 3 5 9 – – – 0.9 1.5 2.7 – – – 0.9 1.5 2.7 – – – 0.9 1.5 2.7 V VIH High–Level Input Voltage – except f in, OSCin 3 5 9 2.1 3.5 6.3 – – – 2.1 3.5 6.3 – – – 2.1 3.5 6.3 – – – V Iin Input Current (fin, OSCin) Vin = VDD or VSS 9 ±2 ± 50 ±2 ± 25 ±2 ± 22 µA IIL Input Leakage Current (Data, CLK, ENB – without pull–ups) Vin = VSS 9 – – 0.3 – – 0.1 – – 1.0 µA IIH Input Leakage Current (all inputs except fin, OSCin) Vin = VDD 9 – 0.3 – 0.1 – 1.0 µA (continued) Page 23 of 35 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx DC ELECTRICAL CHARACTERISTICS (continued) 25 C 85 C Min Max Min Max Min Max Unit 9 – 20 – 400 – 20 – 200 – 20 – 170 µA – – 10 – 10 – 10 pF Symbol Parameter IIL Pull–up Current (all inputs with pull–ups) Cin Input Capacitance VOL Low–Level Output Voltage – OSCout Iout 0 µA Vin = VDD 3 5 9 – – – 0.9 1.5 2.7 – – – 0.9 1.5 2.7 – – – 0.9 1.5 2.7 V VOH High–Level Output Voltage – OSCout Iout 0 µA Vin = VSS 3 5 9 2.1 3.5 6.3 – – – 2.1 3.5 6.3 – – – 2.1 3.5 6.3 – – – V VOL Low–Level Output Voltage – Other Outputs Iout 0 µA 3 5 9 – – – 0.05 0.05 0.05 – – – 0.05 0.05 0.05 – – – 0.05 0.05 0.05 V VOH High–Level Output Voltage – Other Outputs Iout 0 µA 3 5 9 2.95 4.95 8.95 – – – 2.95 4.95 8.95 – – – 2.95 4.95 8.95 – – – V Drain–to–Source Breakdown Voltage – SW1, SW2 Rpull–up = 4.7 kΩ – 15 – 15 – 15 – V IOL Low–Level Sinking Current – MC Vout = 0.3 V Vout = 0.4 V Vout = 0.5 V 3 5 9 1.30 1.90 3.80 – – – 1.10 1.70 3.30 – – – 0.66 1.08 2.10 – – – mA IOH High–Level Sourcing Current – MC Vout = 2.7 V Vout = 4.6 V Vout = 8.5 V 3 5 9 – 0.60 – 0.90 – 1.50 – – – – 0.50 – 0.75 – 1.25 – – – – 0.30 – 0.50 – 0.80 – – – mA IOL Low–Level Sinking Current – LD Vout = 0.3 V Vout = 0.4 V Vout = 0.5 V 3 5 9 0.25 0.64 1.30 – – – 0.20 0.51 1.00 – – – 0.15 0.36 0.70 – – – mA IOH High–Level Sourcing Current – LD Vout = 2.7 V Vout = 4.6 V Vout = 8.5 V 3 5 9 – 0.25 – 0.64 – 1.30 – – – – 0.20 – 0.51 – 1.00 – – – – 0.15 – 0.36 – 0.70 – – – mA IOL Low–Level Sinking Current – SW1, SW2 Vout = 0.3 V Vout = 0.4 V Vout = 0.5 V 3 5 9 0.80 1.50 3.50 – – – 0.48 0.90 2.10 – – – 0.24 0.45 1.05 – – – mA IOL Low–Level Sinking Current – Other Outputs Vout = 0.3 V Vout = 0.4 V Vout = 0.5 V 3 5 9 0.44 0.64 1.30 – – – 0.35 0.51 1.00 – – – 0.22 0.36 0.70 – – – mA IOH High–Level Sourcing Current – Other Outputs Vout = 2.7 V Vout = 4.6 V Vout = 8.5 V 3 5 9 – 0.44 – 0.64 – 1.30 – – – – 0.35 – 0.51 – 1.00 – – – – 0.22 – 0.36 – 0.70 – – – mA IOZ Output Leakage Current – PDout Vout = VDD or VSS Output in Off State 9 – ± 0.3 – ± 0.1 – ± 1.0 µA IOZ Output Leakage Current – SW1, SW2 Vout = VDD or VSS Output in Off State 9 – ± 0.3 – ± 0.1 – ± 3.0 µA Cout Output Capacitance – PDout PDout – Three–State – – 10 – 10 – 10 pF V(BR)DSS Page 24 of 35 Test Condition – 40 C VDD V Vin = VSS www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 10 ns) VDD V Guaranteed Limit 255C Guaranteed Limit – 40 to 85°C Maximum Propagation Delay, fin to MC (Figures 1 and 4) 3 5 9 110 60 35 120 70 40 ns Maximum Propagation Delay, ENB to SW1, SW2 (Figures 1 and 5) 3 5 9 160 80 50 180 95 60 ns Output Pulse Width, φR, φV, and LD with fR in Phase with fV (Figures 2 and 4) 3 5 9 25 to 200 20 to 100 10 to 70 25 to 260 20 to 125 10 to 80 ns tTLH Maximum Output Transition Time, MC (Figures 3 and 4) 3 5 9 115 60 40 115 75 60 ns tTHL Maximum Output Transition Time, MC (Figures 3 and 4) 3 5 9 60 34 30 70 45 38 ns tTLH, tTHL Maximum Output Transition Time, LD (Figures 3 and 4) 3 5 9 180 90 70 200 120 90 ns tTLH, tTHL Maximum Output Transition Time, Other Outputs (Figures 3 and 4) 3 5 9 160 80 60 175 100 65 ns Symbol Parameter tPLH, tPHL tPHL tw Unit SWITCHING WAVEFORMS VDD INPUT 50% – V SS OUTPUT tw tPHL tPLH 50% φR, φV, LD* 50% * fR in phase with fV. Figure 1. Figure 2. tTLH ANY OUTPUT tTHL 90% 10% Figure 3. TEST POINT TEST POINT OUTPUT DEVICE UNDER TEST OUTPUT DEVICE UNDER TEST CL* * Includes all probe and fixture capacitance. Figure 4. Test Circuit Page 25 of 35 VDD 15 kΩ CL* * Includes all probe and fixture capacitance. Figure 5. Test Circuit www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx TIMING REQUIREMENTS (Input tr = tf = 10 ns unless otherwise indicated) Symbol Parameter VDD V Guaranteed Limit 25 C Guaranteed Limit – 40 to 85 C Unit fclk Serial Data Clock Frequency, Assuming 25% Duty Cycle NOTE: Refer to CLK t w(H) below (Figure 6) 3 5 9 DC to 5.0 DC to 7.1 DC to 10 DC to 3.5 DC to 7.1 DC to 10 MHz tsu Minimum Setup Time, Data to CLK (Figure 7) 3 5 9 30 20 18 30 20 18 ns th Minimum Hold Time, CLK to Data (Figure 7) 3 5 9 40 20 15 40 20 15 ns tsu Minimum Setup Time, CLK to ENB (Figure 7) 3 5 9 70 32 25 70 32 25 ns trec Minimum Recovery Time, ENB to CLK (Figure 7) 3 5 9 5 10 20 5 10 20 ns tw(H) Minimum Pulse Width, CLK and ENB (Figure 6) 3 5 9 50 35 25 70 35 25 ns Maximum Input Rise and Fall Times – Any Input (Figure 8) 3 5 9 5 4 2 5 4 2 µs tr, tf SWITCHING WAVEFORMS tw(H) DATA – VDD CLK, ENB CLK Figure 6. tr ENB tf – VDD 90% 10% th VSS 1 * 4 fclk *Assumes 25% Duty Cycle. ANY OUTPUT VSS tsu 50% VSS – VDD 50% 50% FIRST CLK LAST CLK tsu trec 50% PREVIOUS DATA LATCHED – VDD VSS – VDD VSS Figure 7. Figure 8. Page 26 of 35 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx FREQUENCY CHARACTERISTICS (Voltages References to VSS, CL = 50 pF, Input tr = tf =10 ns unless otherwise indicated) Symbol fi Parameter Input Frequency (fin, OSCin) – 40 C 25 C 85 C VDD V Min Max Min Max Min Max Unit R ≥ 8, A ≥ 0, N ≥ 8 Vin = 500 mV p–p AC coupled sine wave 3 5 9 – – – 6 15 15 – – – 6 15 15 – – – 6 15 15 MHz R ≥ 8, A ≥ 0, N ≥ 8 Vin = 1 V p–p AC coupled sine wave 3 5 9 – – – 12 22 25 – – – 12 20 22 – – – 7 20 22 MHz R ≥ 8, A ≥ 0, N ≥ 8 Vin = VDD to VSS DC coupled square wave 3 5 9 – – – 13 25 25 – – – 12 22 25 – – – 8 22 25 MHz Test Condition NOTE: Usually, the PLL's propagation delay from fin to MC plus the setup time of the prescaler determines the upper frequency limit of the system. The upper frequency limit is found with the following formula: f = P / (tP + tset) where f is the upper frequency in Hz, P is the lower of the dual modulus prescaler ratios, tP is the fin to MC propagation delay in seconds, and t set is the prescaler setup time in seconds. For example, with a 5 V supply, the fin to MC delay is 70 ns. If the MC12028A prescaler is used, the setup time is 16 ns. Thus, if the 64/65 ratio is utilized, the upper frequency limit is f = P / (tP + tset) = 64/(70 + 16) = 744 MHz. fR REFERENCE OSC ÷ R VH VL VH fV FEEDBACK (fin ÷ N) * VL VH HIGH IMPEDANCE PDout VL VH φR VL VH φV VL VH LD VL VH = High Voltage Level. VL = Low Voltage Level. * At this point, when both fR and fV are in phase, the output is forced to near mid–supply. NOTE: The PDout generates error pulses during out–of–lock conditions. When locked in phase and frequency the output is high and the voltage at this pin is determined by the low–pass filter capacitor. Figure 9. Phase Detector/Lock Detector Output Waveforms Page 27 of 35 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx DESIGN CONSIDERATIONS PHASE–LOCKED LOOP – LOW–PASS FILTER DESIGN A) PDout φR – VCO R1 ωn = C ζ = φV – F(s) = B) PDout VCO R1 φR – R2 φV – C ωn = R2 PDout – φR φV Nωn 2KφKVCO 1 R1sC + 1 KφKVCO NC(R1 + R2) ζ = 0.5 ωn ( R2C + F(s) = C) KφKVCO NR1C R1 ωn = C _ +A VCO R1 ζ = N KφKVCO ) R2sC + 1 (R1 + R2)sC + 1 KφKVCO NCR1 ωnR2C 2 ASSUMING GAIN A IS VERY LARGE, THEN: R2 C F(s) = R2sC + 1 R1sC NOTE: Sometimes R1 is split into two series resistors, each R1 ÷ 2. A capacitor C C is then placed from the midpoint to ground to further filter φV and φR. The value of C C should be such that the corner frequency of this network does not significantly affect ωn. The φR and φV outputs swing rail–to–rail. Therefore, the user should be careful not to exceed the common mode input range of the op amp used in the combiner/loop filter. DEFINITIONS: N = Total Division Ratio in feedback loop Kφ (Phase Detector Gain) = VDD/4π for PDout Kφ (Phase Detector Gain) = VDD/2π for φV and φR 2π∆fVCO KVCO (VCO Gain) = ∆VVCO for a typical design wn (Natural Frequency) Damping Factor: ζ ≅ 1 2πfr 10 (at phase detector input). RECOMMENDED READING: Gardner, Floyd M., Phaselock Techniques (second edition). New York, Wiley–Interscience, 1979. Manassewitsch, Vadim, Frequency Synthesizers: Theory and Design (second edition). New York, Wiley–Interscience, 1980. Blanchard, Alain, Phase–Locked Loops: Application to Coherent Receiver Design. New York, Wiley–Interscience, 1976. Egan, William F., Frequency Synthesis by Phase Lock. New York, Wiley–Interscience, 1981. Rohde, Ulrich L., Digital PLL Frequency Synthesizers Theory and Design. Englewood Cliffs, NJ, Prentice–Hall, 1983. Berlin, Howard M., Design of Phase–Locked Loop Circuits, with Experiments. Indianapolis, Howard W. Sams and Co., 1978. Kinley, Harold, The PLL Synthesizer Cookbook. Blue Ridge Summit, PA, Tab Books, 1980. AN535, Phase–Locked Loop Design Fundamentals, Motorola Semiconductor Products, Inc., 1970. AR254, Phase–Locked Loop Design Articles, Motorola Semiconductor Products, Inc., Reprinted with permission from Electronic Design, 1987. Page 28 of 35 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx CRYSTAL OSCILLATOR CONSIDERATIONS The following options may be considered to provide a reference frequency to Motorola's or Lansdale’s CMOS frequency synthesizers. Use of a Hybrid Crystal Oscillator Commercially available temperature–compensated crystal oscillators (TCXOs) or crystal–controlled data clock oscillators provide very stable reference frequencies. An oscillator capable of sinking and sourcing 50 µA at CMOS logic levels may be direct or DC coupled to OSCin. In general, the highest frequency capability is obtained utilizing a direct–coupled square wave having a rail–to–rail (VDD to VSS) voltage swing. If the oscillator does not have CMOS logic levels on the outputs, capacitive or AC coupling to OSCin may be used. OSCout, an unbuffered output, should be left floating. For additional information about TCXOs and data clock oscillators, please consult the latest version of the eem Electronic Engineers Master Catalog, the Gold Book, or similar publications. Design an Off–Chip Reference The user may design an off–chip crystal oscillator using ICs specifically developed for crystal oscillator applications, such as the ML12061 MECL device. The reference signal from the MECL device is AC coupled to OSCin. For large amplitude signals (standard CMOS logic levels), DC coupling is used. OSCout, an unbuffered output, should be left floating. In general, the highest frequency capability is obtained with a direct–coupled square wave having rail–to–rail voltage swing. Use of the On–Chip Oscillator Circuitry The on–chip amplifier (a digital inverter) along with an appropriate crystal may be used to provide a reference source frequency. A fundamental mode crystal, parallel resonant at the desired operating frequency, should be connected as shown in Figure 10. FREQUENCY SYNTHESIZER Rf OSCin C1 R1* OSCout C2 * May be deleted in certain cases. See text. Figure 10. Pierce Crystal Oscillator Circuit For VDD = 5.0 V, the crystal should be specified for a loading capacitance, CL, which does not exceed 32 pF for frequencies to approximately 8.0 MHz, 20 pF for frequencies in the area of 8.0 to 15 MHz, and 10 pF for higher frequencies. These are guidelines that provide a reasonable compromise between IC capacitance, drive capability, swamping variations in stray and IC input/output capacitance, and realistic CL values. The shunt load capacitance, CL, presented across the crystal can be estimated to be: Page 29 of 35 CL = CinCout + Ca + Co + C1 • C2 C1 + C2 Cin + Cout where Cin = Cout = Ca = CO = 5 pF (see Figure 11) 6 pF (see Figure 11) 1 pF (see Figure 11) the crystal's holder capacitance (see Figure 12) C1 and C2 = external capacitors (see Figure 10) Ca Cin Cout Figure 11. Parasitic Capacitances of the Amplifier RS 1 2 LS CS 1 2 CO 1 Re Xe 2 NOTE: Values are supplied by crystal manufacturer (parallel resonant crystal). Figure 12. Equivalent Crystal Networks The oscillator can be “trimmed” on–frequency by making a portion or all of C1 variable. The crystal and associated components must be located as close as possible to the OSCin and OSCout pins to minimize distortion, stray capacitance, stray inductance, and startup stabilization time. In some cases, stray capacitance should be added to the value for Cin and Cout. Power is dissipated in the effective series resistance of the crystal, Re, in Figure 12. The drive level specified by the crystal manufacturer is the maximum stress that a crystal can withstand without damage or excessive shift in frequency. R1 in Figure 10 limits the drive level. The use of R1 may not be necessary in some cases (i.e., R1 = 0 Ω). To verify that the maximum DC supply voltage does not overdrive the crystal, monitor the output frequency as a function of voltage at OSCout. (Care should be taken to minimize loading.) The frequency should increase very slightly as the DC supply voltage is increased. An overdriven crystal will decrease in frequency or become unstable with an increase in supply voltage. The operating supply voltage must be reduced or R1 must be increased in value if the overdriven condition exists. The user should note that the oscillator start–up time is proportional to the value of R1. Through the process of supplying crystals for use with CMOS inverters, many crystal manufacturers have developed expertise in CMOS oscillator design with crystals. Discussions with such manufacturers can prove very helpful (see Table 1). www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx Table 1. Partial List of Crystal Manufacturers United States Crystal Corp. Crystek Crystal Statek Corp. Fox Electronics NOTE: Lansdale and Motorola do not recommend one supplier over another and in no way suggests that this is a complete listing of crystal manufacturers. RECOMMENDED READING Technical Note TN–24, Statek Corp. Technical Note TN–7, Statek Corp. E. Hafner, “The Piezoelectric Crystal Unit – Definitions and Method of Measurement”, Proc. IEEE, Vol. 57, No. 2 Feb.,1969. D. Kemper, L. Rosine, “Quartz Crystals for FrequencyControl”, Electro–Technology, June, 1969. P. J. Ottowitz, “A Guide to Crystal Selection”, Electronic Design, May, 1966. DUAL–MODULUS PRESCALING OVERVIEW The technique of dual–modulus prescaling is well established as a method of achieving high performance frequency synthesizer operation at high frequencies. Basically, the approach allows relatively low–frequency programmable counters to be used as high–frequency programmable counters with speed capability of several hundred MHz. This is possible with out the sacrifice in system resolution and performance that results if a fixed (single–modulus) divider is used for the prescaler. In dual–modulus prescaling, the lower speed counters must be uniquely configured. Special control logic is necessary to select the divide value P or P + 1 in the prescaler for the required amount of time (see modulus control definition). Lansdale's dual–modulus frequency synthesizers contain this feature and can be used with a variety of dual–modulusprescalers to allow speed, complexity and cost to be tailored to the system requirements. Prescalers having P, P + 1 divide values in the range of ÷ 3/÷4 to ÷128/÷ 129 can be controlled by most Lansdale frequency synthesizers. Several dual–modulus prescaler approaches suitable for use with the MC145152 (Motorola), ML145156, or ML145158 are: ML12009 ML12011 ML12013 ML12015 ML12016 ML12017 ML12018 MC12028A MC12034 MC12038 ML12052 ML12054A Page 30 of 35 ÷ 5/÷ 6 ÷ 8/÷ 9 ÷ 10/÷ 11 ÷ 32/÷ 33 ÷ 40/÷ 41 ÷ 64/÷ 65 ÷ 128/÷ 129 ÷ 32/33 or ÷ 64/65 ÷32/33 or ÷64/65 ÷127/128 or ÷255/256 ÷ 64/65 or ÷ 128/129 ÷ 64/65 or ÷ 128/129 440 MHz 500 MHz 500 MHz 225 MHz 225 MHz 225 MHz 520 MHz 1.1 GHz 2.0 GHz 1.1 GHz 1.1 GHz 2.0 GHz DESIGN GUIDELINES The system total divide value, N total (NT) will be dictated by the application: N is the number programmed into the ÷ N counter, A is the NT = frequency into the prescaler =N• P+A frequency into the phase detector number programmed into the ÷ A counter, P and P + 1 are the two selectable divide ratios available in the dual–modulus prescalers. To have a range of NT values in sequence, the ÷ A counter is programmed from zero through P – 1 for a particular value N in the ÷ N counter. N is then incremented to N + 1 and the ÷ A is sequenced from 0 through P – 1 again. There are minimum and maximum values that can be achieved for NT. These values are a function of P and the size of the ÷ N and ÷ A counters. The constraint N ≥ A always applies. If Amax = P – 1, then Nmin ≥ P – 1. Then NT min = (P – 1) P + A or (P – 1) P since A is free to assume the value of 0. NTmax = Nmax • P + Amax To maximize system frequency capability, the dual–modulus prescaler output must go from low to high after each group of P or P + 1 input cycles. The prescaler should divide by P when its modulus control line is high and by P + 1 when its MC is low. For the maximum frequency into the prescaler (fVCOmax), the value used for P must be large enough such that: 1.fVCOmax divided by P may not exceed the frequency capability of f in (input to the ÷ N and ÷ A counters). 2.The period of fVCO divided by P must be greater than the sum of the times: a. Propagation delay through the dual–modulus prescaler. b. Prescaler setup or release time relative to its MC signal. c. Propagation time from f in to the MC output for the frequency synthesizer device. A sometimes useful simplification in the programming code can be achieved by choosing the values for P of 8, 16, 32, or 64. For these cases, the desired value of NT results when NT in binary is used as the program code to the ÷ N and ÷ A counters treated in the following manner: 1.Assume the ÷A counter contains “a” bits where 2a ≥P. 2.Always program all higher order ÷A counter bits above “a” to 0. www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx 3. Assume the ÷N counter and the ÷A counter (with all the higher order bits above “a” ignored) combined into a single binary counter of n + a bits in length (n = number of divider stages in the ÷N counter). The MSB of this “hypothetical” counter is to correspond to the MSB of ÷ N and the LSB is to correspond to the LSB of ÷ A. The system divide value, NT, now results when the value of NT in binary is used to program the “new” n + a bit counter. By using the two devices, several dual–modulus values are achievable (shown in Figure 13). MC DEVICE A DEVICE B DEVICE A ML12009 MC10131 ÷ 20/÷ 21 MC10138 ÷ 50/÷ 51 DEVICE B ML12011 ML12013 ÷ 32/÷ 33 ÷ 80/÷ 81 ÷ 40/÷ 41 ÷ 100/÷ 101 NOTE: ML12009, ML12011, and ML12013 are pin equivalent. ML12015, ML12016, and ML12017 are pin equivalent. Figure 13. Dual–Modulus Values Page 31 of 35 www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx OUTLINE DIMENSIONS P DIP 16 = EP PLASTIC DIP CASE 648–08 (ML145157EP, ML145158EP) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL. –A– 16 9 B F C DIM A B C D F G H J K L M S L S –T– SEATING PLANE K H G D M J 16 PL 0.25 (0.010) M T A M INCHES MIN MAX 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 BSC 0.050 BSC 0.008 0.015 0.110 0.130 0.295 0.305 0° 10° 0.020 0.040 MILLIMETERS MIN MAX 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 BSC 1.27 BSC 0.21 0.38 2.80 3.30 7.50 7.74 0° 10° 0.51 1.01 P DIP 18 = VP PLASTIC DIP CASE 707–02 (ML145155VP) 18 NOTES: 1. POSITIONAL TOLERANCE OF LEADS (D), SHALL BE WITHIN 0.25 (0.010) AT MAXIMUM MATERIAL CONDITION, IN RELATION TO SEATING PLANE AND EACH OTHER. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 10 B A L C N F H Page 32 of 35 D G SEATING PLANE K M J www.lansdale.com DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 22.22 23.24 6.10 6.60 3.56 4.57 0.36 0.56 1.27 1.78 2.54 BSC 1.02 1.52 0.20 0.30 2.92 3.43 7.62 BSC 0° 15° 0.51 1.02 INCHES MIN MAX 0.875 0.915 0.240 0.260 0.140 0.180 0.014 0.022 0.050 0.070 0.100 BSC 0.040 0.060 0.008 0.012 0.115 0.135 0.300 BSC 0° 15° 0.020 0.040 Issue A LANSDALE Semiconductor, Inc. ML1451xx OUTLINE DIMENSIONS P DIP 20 = RP PLASTIC DIP CASE 738–03 (ML145156RP) -A20 11 1 10 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. B C -T- L DIM A B C D E F G J K L M N K SEATING PLANE M E G N F J 20 PL 0.25 (0.010) D 20 PL 0.25 (0.010) M T A M T B M M INCHES MIN MAX 1.010 1.070 0.240 0.260 0.150 0.180 0.015 0.022 0.050 BSC 0.050 0.070 0.100 BSC 0.008 0.015 0.110 0.140 0.300 BSC 15° 0° 0.020 0.040 MILLIMETERS MIN MAX 25.66 27.17 6.10 6.60 3.81 4.57 0.39 0.55 1.27 BSC 1.27 1.77 2.54 BSC 0.21 0.38 2.80 3.55 7.62 BSC 0° 15° 1.01 0.51 SOG 20 = -6P SOG PACKAGE CASE 751D–04 (MC145155-6P, MC145156-6P) NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.150 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOW ABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. –A– 20 11 –B– 10X P 0.010 (0.25) 1 M B M 10 20X D 0.010 (0.25) M T A B S J S F R C –T– 18X Page 33 of 35 G K SEATING PLANE X 45° DIM A B C D F G J K M P R MILLIMETERS MIN MAX 12.65 12.95 7.40 7.60 2.35 2.65 0.35 0.49 0.50 0.90 1.27 BSC 0.25 0.32 0.10 0.25 0° 7° 10.05 10.55 0.25 0.75 INCHES MIN MAX 0.499 0.510 0.292 0.299 0.093 0.104 0.014 0.019 0.020 0.035 0.050 BSC 0.010 0.012 0.004 0.009 0° 7° 0.395 0.415 0.010 0.029 M www.lansdale.com Issue A LANSDALE Semiconductor, Inc. ML1451xx OUTLINE DIMENSIONS P DIP 28 = YP PLASTIC DIP CASE 710–02 (ML145151YP, ML145152YP) 28 NOTES: 1. POSITIONAL TOLERANCE OF LEADS (D), SHALL BE WITHIN 0.25mm (0.010) AT MAXIMUM MATERIAL CONDITION, IN RELATION TO SEATING PLANE AND EACH OTHER. 2. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 3. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 15 B 1 14 A DIM A B C D F G H J K L M N L C N H G M K D F J SEATING PLANE MILLIMETERS MIN MAX 36.45 37.21 13.72 14.22 3.94 5.08 0.36 0.56 1.02 1.52 2.54 BSC 1.65 2.16 0.20 0.38 2.92 3.43 15.24 BSC 0° 15° 0.51 1.02 INCHES MIN MAX 1.435 1.465 0.540 0.560 0.155 0.200 0.014 0.022 0.040 0.060 0.100 BSC 0.065 0.085 0.008 0.015 0.115 0.135 0.600 BSC 0° 15° 0.020 0.040 SO 28W = -6P SOG PACKAGE CASE 751F–04 (ML145151-6P, ML145152–6P) -A28 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. 15 14X -B1 P 0.010 (0.25) M B M 14 28X D 0.010 (0.25) M T A S B M S R X 45° C -T26X -T- G K SEATING PLANE F J Page 34 of 35 www.lansdale.com DIM A B C D F G J K M P R MILLIMETERS MIN MAX 17.80 18.05 7.60 7.40 2.65 2.35 0.49 0.35 0.90 0.41 1.27 BSC 0.32 0.23 0.29 0.13 8° 0° 10.05 10.55 0.25 0.75 INCHES MIN MAX 0.701 0.711 0.292 0.299 0.093 0.104 0.014 0.019 0.016 0.035 0.050 BSC 0.009 0.013 0.005 0.011 0° 8° 0.395 0.415 0.010 0.029 Issue A LANSDALE Semiconductor, Inc. ML1451xx OUTLINE DIMENSIONS SOG 20 = -5P SOG PACKAGE CASE 751G–02 (ML145157-5P, ML145158-5P) –A– 16 9 –B– 8X P 0.010 (0.25) 1 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOW ABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. M B M 8 16X J D 0.010 (0.25) M T A S B S F R X 45° C –T– 14X G K SEATING PLANE M DIM A B C D F G J K M P R MILLIMETERS MIN MAX 10.15 10.45 7.40 7.60 2.35 2.65 0.35 0.49 0.50 0.90 1.27 BSC 0.25 0.32 0.10 0.25 0° 7° 10.05 10.55 0.25 0.75 INCHES MIN MAX 0.400 0.411 0.292 0.299 0.093 0.104 0.014 0.019 0.020 0.035 0.050 BSC 0.010 0.012 0.004 0.009 0° 7° 0.395 0.415 0.010 0.029 Lansdale Semiconductor reserves the right to make changes without further notice to any products herein to improve reliability, function or design. Lansdale does not assume any liability arising out of the application or use of any product or circuit described herein; neither does it convey any license under its patent rights nor the rights of others. Typical ” parameters which may be provided in Lansdale data sheets and/or specifications can vary in different applications, and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by the customer’s technical experts. Lansdale Semiconductor is a registered trademark of Lansdale Semiconductor, Inc. Page 35 of 35 www.lansdale.com Issue A