AOZ8001DI Ultra-Low Capacitance TVS Diode Array General Description Features The AOZ8001DI is a transient voltage suppressor array designed to protect high speed data lines from ESD and lightning. This device incorporates four surge rated, low capacitance steering diodes and a TVS in a single package. During transient conditions, the steering diodes direct the transient to either the positive side of the power supply line or to ground. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4. The TVS diodes provide effective suppression of ESD voltages: ±15kV (air discharge) and ±8kV (contact discharge). ESD protection for high-speed data lines: – IEC 61000-4-2, level 4 (ESD) immunity test – ±15kV (air discharge) and ±8kV (contact discharge) – IEC 61000-4-5 (Lightning) 5A (8/20µs) – Human Body Model (HBM) ±15kV Small package saves board space Low insertion loss Protects four I/O lines Low capacitance from IO to Ground: 1.0pF Low clamping voltage Low operating voltage: 5.0V The AOZ8001DI comes in a RoHS compliant DFN 1.6mm x 1.6mm package and is rated over a -40°C to +85°C ambient temperature range. It is compatible with both lead free and SnPb assembly techniques. Pb-free device Green product The very small 1.6mm x 1.6mm DFN package makes it ideal for applications where PCB space is a premium. The DFN has a flow through package design for an optimal and user friendly PCB layout design. The small size, low capacitance and high ESD protection makes it ideal for protecting high speed video and data communication interfaces. USB 2.0 power and data line protection Video graphics cards Monitors and flat panel displays Digital Video Interface (DVI) 10/100/1000 Ethernet Notebook computers Applications Typical Application USB Controller USB Controller +5V +5V AOZ8001DI D+ D- 1 6 2 5 3 4 GND D+ D- GND Figure 1. USB 2.0 High Speed Port Rev. 1.0 November 2011 www.aosmd.com Page 1 of 10 AOZ8001DI Ordering Information Part Number Ambient Temperature Range Package Environmental AOZ8001DI -40°C to +85°C DFN 1.6 x 1.6 RoHS Compliant Green Product AOS Green Products use reduced levels of Halogens, and are also RoHS compliant. Please visit www.aosmd.com/web/quality/rohs_compliant.jsp for additional information. Pin Configuration CH1 1 6 NC VN 2 5 VP NC 3 4 CH2 DFN-6 (Top View) Absolute Maximum Ratings Exceeding the Absolute Maximum ratings may damage the device. Parameter Rating VP – VN 6V Peak Pulse Current (IPP), tP = 8/20µs 5A Storage Temperature (TS) -65°C to +150°C ESD Rating per IEC61000-4-2, Contact(1) ESD Rating per IEC61000-4-2, Air ESD Rating per Human Body ±8kV (1) ±15kV Model(2) ±15kV Notes: 1. IEC 61000-4-2 discharge with CDischarge = 150pF, RDischarge = 330¾. 2. Human Body Discharge per MIL-STD-883, Method 3015 CDischarge = 100pF, RDischarge = 1.5k¾. Maximum Operating Ratings Parameter Rating Junction Temperature (TJ) Rev. 1.0 November 2011 -40°C to +125°C www.aosmd.com Page 2 of 10 AOZ8001DI Electrical Characteristics TA = 25°C unless otherwise specified. Specifications in BOLD indicate a temperature range of -40°C to +85°C. Symbol VRWM Parameter Reverse Working Voltage Conditions Min. (4) Reverse Breakdown Voltage IT = 1mA, between pins 5 and 2 IR Reverse Leakage Current VRWM = 5V, between pins 5 and 2 VF Diode Forward Voltage IF = 15mA Cj 5.5 V 6.6 0.70 Channel Clamp Voltage Positive Transients Negative Transient IPP = 1A, tp = 100ns, any I/O pin to Ground Channel Clamp Voltage Positive Transients Negative Transient IPP = 5A, tp = 100ns, any I/O pin to Ground(5)(7) Channel Clamp Voltage Positive Transients Negative Transient IPP = 12A, tp = 100ns, any I/O pin to Ground(5)(7) Junction Capacitance VR = 0V, f = 1MHz, between I/O pins(6) Channel Input Capacitance Matching Units V 1.0 µA 1 V 10.00 -2.00 V V 11.00 -5.00 V V 14.50 -10.50 V V 0.1 0.12 pF 1.0 1.17 pF 0.03 pF 0.85 (5)(7) VR = 0V, f = 1MHz, any I/O pin to Cj Max. Between pin 5 and 2(3) VBR VCL Typ. VR = 0V, f = 1MHz, between I/O Ground(6) pins(5) Notes: 3. The working peak reverse voltage, VRWM, should be equal to or greater than the DC or continuous peak operating voltage level. 4. VBR is measured at the pulse test current IT. 5. Measurements performed with no external capacitor on VP (pin 5 floating). 6. Measurements performed with VP biased to 3.3 Volts (pin 5 @ 3.3V). 7. Measurements performed using a 100ns Transmission Line Pulse (TLP) system. Rev. 1.0 November 2011 www.aosmd.com Page 3 of 10 AOZ8001DI Typical Performance Characteristics Typical Variation of CIN vs VR Clamping Voltage vs. Peak Pulse Current (f = 1MHz, T = 25∞C) (tperiod = 100ns, tr = 1ns) 15 Clamping Voltage, VCL (V) 1.25 1.0 0.75 Vp = 3.3V 0.50 0.25 14 13 12 11 10 9 0 0 1 2 3 4 5 0 Input Voltage (V) Forward Voltage vs. Forward Current 2 4 6 8 Peak Pulse Current, IPP (A) Insertion Loss (dB) Forward Voltage (V) 10 8 6 4 2 0 2 4 6 8 12 (Vp = 3.3V) 12 0 10 I/O – Gnd Insertion Loss (S21) vs. Frequency (tperiod = 100ns, tr = 1ns) 10 1 0 -1 -2 -3 -4 -5 -6 -7 -8 -9 -10 12 1 10 100 1000 Forward Current (A) Frequency (MHz) Analog Crosstalk (I/O–I/O) vs. Frequency ESD Response (8kV Contact per IEC61000-4-2) 20 Insertion Loss (dB) Input Capacitance (pF) 1.5 0 -20 -40 -60 -80 10 100 1000 Frequency (MHz) Rev. 1.0 November 2011 www.aosmd.com Page 4 of 10 AOZ8001DI Application Information The AOZ8001DI TVS is design to protect two data lines from fast damaging transient over-voltage by clamping it to a reference. When the transient on a protected data line exceed the reference voltage the steering diode is forward bias thus, conducting the harmful ESD transient away from the sensitive circuitry under protection. PCB Layout Guidelines Printed circuit board layout is the key to achieving the highest level of surge immunity on power and data lines. The location of the protection devices on the PCB is the simplest and most important design rule to follow. The AOZ8001DI devices should be located as close as possible to the noise source. The placement of the AOZ8001DI devices should be used on all data and power lines that enter or exit the PCB at the I/O connector. In most systems, surge pulses occur on data and power lines that enter the PCB through the I/O connector. Placing the AOZ8001DI devices as close as possible to the noise source ensures that a surge voltage will be clamped before the pulse can be coupled into adjacent PCB traces. In addition, the PCB should use the shortest possible traces. A short trace length equates to low impedance, which ensures that the surge energy will be dissipated by the AOZ8001DI device. Long signal traces will act as antennas to receive energy from fields that are produced by the ESD pulse. By keeping line lengths as short as possible, the efficiency of the line to act as an antenna for ESD related fields is reduced. Minimize interconnecting line lengths by placing devices with the most interconnect as close together as possible. The protection circuits should shunt the surge voltage to either the reference or chassis ground. Shunting the surge voltage directly to the IC’s signal ground can cause ground bounce. The clamping performance of TVS diodes on a single ground PCB can be improved by minimizing the impedance with relatively short and wide ground traces. The PCB layout and IC package parasitic inductances can cause significant overshoot to the TVS’ clamping voltage. The inductance of the PCB can be reduced by using short trace lengths and multiple layers with separate ground and power planes. One effective method to minimize loop problems is to incorporate a ground plane in the PCB design. The AOZ8001DI ultra-low capacitance TVS is designed to protect four high speed data transmission lines from transient over-voltages by clamping them to a fixed reference. The low inductance and construction minimizes voltage overshoot during high current surges. When the voltage on the protected line exceeds the reference voltage the internal steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. Good circuit board layout is critical for the suppression of ESD induced transients. The following guidelines are recommended: 1. Place the TVS near the IO terminals or connectors to restrict transient coupling. 2. Fill unused portions of the PCB with ground plane. 3. Minimize the path length between the TVS and the protected line. 4. Minimize all conductive loops including power and ground loops. 5. The ESD transient return path to ground should be kept as short as possible. 6. Never run critical signals near board edges. 7. Use ground planes whenever possible. 8. Avoid running critical signal traces (clocks, resets, etc.) near PCB edges. 9. Separate chassis ground traces from components and signal traces by at least 4mm. 10. Keep the chassis ground trace length-to-width ratio <5:1 to minimize inductance. 11. Protect all external connections with TVS diodes. Connector Protected IC D+ D+ D- DFlow Through Layout Rev. 1.0 November 2011 www.aosmd.com Page 5 of 10 AOZ8001DI AOZ8001DI VCC Reset AOZ8001DI Clock SIM I/O GND SIM Card Port Connection TPBIASx AOZ8001DI TPAx+ TPAx- IEEE 1394 PHY IEEE 1394 Connector AOZ8001DI TPBx+ TPBx- GND IEEE1394 Port Connection Rev. 1.0 November 2011 www.aosmd.com Page 6 of 10 AOZ8001DI AOZ8001DI TRD0+ TRD0- AOZ8001DI TRD1+ TRD1- Ethernet Controller AOZ8001DI RJ45 Connector TRD2+ TRD2- AOZ8001DI TRD3+ TRD3- 10/100 Ethernet Port Connection Rev. 1.0 November 2011 www.aosmd.com Page 7 of 10 AOZ8001DI Package Dimensions, DFN 1.6 x 1.6 D e b 6 E L 1 TOP VIEW e1 Pin 1 ID BOTTOM VIEW A A1 SIDE VIEW c RECOMMENDED LAND PATTERN Dimensions in millimeters 0.50 1.25 Symbols A Min. 0.50 A1 b c 0.00 0.22 D 1.55 1.55 E e 0.45 e1 L 0.30 Nom. 0.55 Max. 0.60 0.02 0.05 0.25 0.28 1.52 REF. 1.60 1.60 1.65 1.65 0.50 BSC 0.225 1.0 REF 0.275 0.325 UNIT: mm Notes: 1. Dimensions and tolerancing conform to ASME Y14.5M-1994. 2. All dimensions are in millimeters. Rev. 1.0 November 2011 www.aosmd.com Page 8 of 10 AOZ8001DI Tape and Reel Dimensions, DFN 1.6 x 1.6 Carrier Tape P2 P1 D1 D0 E1 K0 E2 E B0 5 Max. A0 P0 T Feeding Direction UNIT: mm Package DFN 1.6x1.6 A0 1.78 ±0.05 B0 1.78 ±0.05 K0 0.69 ±0.05 D0 ø1.50 ±0.10 D1 E E1 ø0.50 8.00 1.75 ±0.05 +0.30 / -0.10 ±0.10 E2 3.50 ±0.05 P0 4.00 ±0.10 P1 4.00 ±0.10 P2 2.00 ±0.05 T 0.20 ±0.02 Reel W1 S M K N G R H W UNIT: mm Tape Size Reel Size 8mm ø178 M ø178.0 ±1.0 N ø60.0 ±1.0 W 11.80 ±0.5 W1 9.0 ±0.5 H ø13.0 +0.5 / –0.2 S 2.40 ±0.10 K 10.25 ±0.2 E ø9.8 R — Leader / Trailer & Orientation Trailer Tape 300mm Min. Rev. 1.0 November 2011 Components Tape Orientation in Pocket www.aosmd.com Leader Tape 500mm Min. Page 9 of 10 AOZ8001DI Part Marking AOZ8001DI (DFN 1.6 x 1.6) F Product Number Code Assembly Lot Code Week Code This datasheet contains preliminary data; supplementary data may be published at a later date. Alpha & Omega Semiconductor reserves the right to make changes at any time without notice. LIFE SUPPORT POLICY ALPHA & OMEGA SEMICONDUCTOR PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. Rev. 1.0 November 2011 2. A critical component in any component of a life support, device, or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.aosmd.com Page 10 of 10