7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. ATLANTIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER 4 3 2 20 REVISION DESCRIPTION A 2151591 -2 DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 5 FINE CRIMP HEIGHT ADJUST A 2151591 -5 SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED FINE CRIMP HEIGHT ADJUST SERVO LATCH PLATE 12 A NON-CRIMP HEIGHT ADJUST 2151591 -7 A FINE CRIMP HEIGHT ADJUST A PNEUMATIC FEED SERVO LATCH PLATE 2151591 -6 7- 2151591 -7 CONVERT TO MECHANICAL FINE CRIMP HEIGHT ADJUST A APPLICATOR STYLE CONVERSION CHART FEED TYPE 4 NONE CRIMP TOOLING KIT - 4 PNEUMATIC FEED - CRIMP WIRE INSUL SIZE 2119950-1 1338685-1 2161326-1 - 2119951-1 - 2119949-1 1338685-1 2119951-1 - 2161326-1 - 2119949-1 1338685-1 2119950-1 5-18022-5 8- 2151591 -5 8- 2151591 -4 5-18022-5 8- 2151591 -5 8- 2151591 -4 5-18022-5 1338685-1 - 5-18022-5 - - 2119641-1 2119799-1 - - 1901094-3 2119653-1 1901094-3 - 2119653-1 2119641-1 - - - - - - - - - - - - - - - - - 2168400-6 2168400-6 - 2119799-1 - (QUANTITY 2) - - - (QUANTITY 2) - - - - - 2063440-1 - - - - - - - - - - - - - - TYPE 1.90 mm [.075] APPLICATOR INSTRUCTIONS 408-10389 - TE TERMINAL TERMINAL DATA: 2.8mm RECEPTACLE UNSEALED TERMINAL NAME: WIRE STRIP LENGTH 4.80-5.60 mm [.189-.220 IN] C TERMINAL APPLICATION SPECIFICATION n 114-13013 - - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 1.19-1.65 mm [.047-.065 IN] - - - - - - - TERMINALS APPLIED TE TERMINAL 1326030-5 TE TERMINAL 1326029-5 C1__DWG_PN_1_0 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 - TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_2_1 - WIRE SIZE 22 AWG 0.35mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 1.04+/-0.05 [.041+/-.002] 1.04+/-0.05 [.041+/-.002] CRIMP HEIGHT REFERENCE SETTING 9.1 W1__DWG_CRIMP_HT_1 9.1 W1__DWG_CRIMP_HT_2 - 9 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - B 1 RECOMMENDED SPARE PARTS 2 GREASE BEARING SURFACES LIGHTLY - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8SERVO FEED WITH "NON-CRIMP HEIGHT ADJUST": 8- 2151591 2151591 2151591 2151591 - -4 -4 -5 -6 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. 6 7 8 9 10 11 A 12 - APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62, 180 FOR -6 ONLY APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 37, 180 GREASE THREADS, GROOVE AND O-RING ON ITEMS 35 & 242. 1 & 242. & 252. 1 MAGNET, ITEM 166 MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. 1 1 CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON THE BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. WHEN ASSEMBLING A NON CRIMP HEIGHT ADJUST APPLICATOR (-6) USE SHIMS FROM ITEM 260 TO ACHIEVE A NOMINAL SHIM HEIGHT OF - 1 1 - -77 -7 1 1 - -6 1 1 - -5 1 1 1 1 1 -2 - 240792-2 2119957-2 8-21084-0 2119640-1 2079988-1 2119641-1 -1 PART NO 1 1 - DRAG, TERMINAL APPLICATOR SHIM PACK O-RING, .676 ID, .070 DIA. MAT. PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI FEED CAM, AIR FEED DESCRIPTION 1 240792-2 1 2119957-2 1 8-21084-0_GATD 1 2119640-1 1 2079988_GATD 1 2119641-1 263 260 252 250 249 248 ITEM NO 1 - 1 1 1 1 - 1 1 1 1 1 1 REF 1 1 1 1 1 1 2 1 3 1 1 4 2 1 1 1 - - 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 - 1 - 1 66 P LTR DESCRIPTION DATE RELEASED 1 1 1 - 1 1 mm MATERIAL - -1 PART NO - 2 1 1 - - - 1 - - 1 - 1 1 1 1 - - - 1 1 - - - 1 1 2 - 1 1 1 2 1 1 1 1 - 1 1 1 1 - 1 2119798-1 1-22279-3 2119758-1 2119082-8 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-5 5-547505-2 854769-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 2079383-4 5-18022-5 21028-2 1338685-1 2168400-1 1-2168083-0 5018030-1 811242-5 690753-2 18023-9 2119652-1 2119653-1 2119656-9 2119370-1 2079383-7 2119645-1 2119957-1 2119644-1 2119085-1 2119092-1 1752356-1 2079383-5 2161328-1 1-1320908-0 2119959-4 455888-3 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 4-1633711-6 2119780-7 238011-9 3-1633962-4 455888-9 8-1633588-3 1 - 1 1 REF REF REF REF - - - 1 - - 1 - 1 1 1 1 1 1 -6 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 - 1 1 1 - 1 - 1 1 2 - - - 1 1 - 1 1 1 - - 1 1 1 - 2 1 1 - 4 2 1 1 1 4 2 1 1 1 4 1 1 1 - 2 1 1 1 4 3 1 - - 1 3 1 1 2 1 3 - 1 2 1 1 1 1 2 - 1 1 - - 1 1 1 2 1 1 1 - - 1 1 1 1 - 1 1 - 1 REF REF 1 - - 1 1 - - 1 1 - 1 REF REF 1 - 1 1 -5 -2 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: & 4 of 4) 1 -77 -7 4.76 . Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 - - ATLANTIC VERSION AMP 4805 REV 31MAR2000 A DWN APVD CC 13JUN2013 TE 2063440-1 F F 1.60 mm [.063] REVISIONS DIST A - APPLICATOR DATA 1 PART NUMBERS REQUIRED - LOC SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 2151591 -1 D 6 TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DETENT PIN SPRING, COMPRESSION RAM, AMP STYLE, SIDE FEED, NON-ADJ. CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, BHSC, RoHS (M4 X 8) SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SHCS, LOW HEAD, RoHS, M4 X 12 SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, AMP STYLE, SIDE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION FA HEAD, ATLANTIC STYLE BOLT, ADJUSTMENT SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE DWN 28MAR2013 CHK 28MAR2013 APVD 28MAR2013 C.CHEN C.CHEN I.CRUZ NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 1 2119082-8 1 2079764 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-5 1 SIMP_5-547505-2 1 854769-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 2079383-4 1 5-18022-5 1 21028-2 1 1338685-1 4 2168400-1 2 1-2168083-0 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2119653 1 2119656-9 1 2119370 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 2119085 1 2119092-1 1 1752356-1 2 2079383-5 1 2161328 1 1-1320908-0 1 2119959-4 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 4-1633711-6 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-7 1 238011-9 1 3-1633962-4 1 455888-9 1 8-1633588-3 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2119758 247 246 245 244 243 242 241 240 239 238 213 198 172 166 164 163 137 136 135 133 119 117 82 77 74 71 67 66 63 62 60 59 58 56 54 53 52 51 50 49 48 47 46 44 41 40 39 38 37 35 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 1-22279-3_SIMP DESCRIPTION PRODUCT SPEC - 1 2119798-1 Ocean Side Feed Applicator - DRAWING NO 2151591 SCALE 1:1 RESTRICTED TO SHEET 1 OF - 4 & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. 6 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. 1 REVISIONS DIST 66 P LTR A DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 D 247 38 2 249 246 260 44 7 252 245 35 244 7 63 166 238 242 8 2 2 6 82 172 3.99 0.50 [ 0.157 0.019 ] 1 34 REF 1 C 2 52 56 3 51 SERVO LATCH PLATE 4 REF 50 137 TERMINAL SUPPORT LOCATION 1 4 28 5 41 135 198 66 164 A 2 11 33 67 213 24 30 10 A 77 58 74 19 SERVO FEEDER NOT INCLUDED B 2 8 136 133 2 163 59 240 2 243 53 C - D 39 A - - 40 56 PNEUMATIC APVD 62 6 59 250 DWN 37 6 239 DATE SEE SHEET 1 - FEED TYPE MECHANICAL DESCRIPTION 20 117 REF B 21 9 29 1 12 ITEM 30 LOCATED AT FRONT HOLES 241 263 CAM POSITIONS 47 1 30 REF 29 REF 11 11 119 30mm STROKE 30mm STROKE 30mm STROKE 13 46 32 34 54 8 1 60 54 10 1 FEED TRACK POSITION GUIDE BY INSULATION BARREL 248 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. 49 40mm STROKE MECHANICAL POST FEED AMP 4805 REV 31MAR2000 49 40mm STROKE MECHANICAL PRE FEED 49 40mm STROKE AIR FEED DIMENSIONS: ATLANTIC VERSION Shown on sheets 1 of 4 & 2 of 4 (Pacific version shown on sheets 3 of 4 mm & 4 of 4) MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 28MAR2013 CHK 28MAR2013 APVD 28MAR2013 C.CHEN C.CHEN I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 3 Ocean Side Feed Applicator - DRAWING NO 2151591 SCALE 1:1 RESTRICTED TO SHEET 2 OF & 4 ARE NOT REQUIRED FOR ATLANTIC VERSION - 4 REV A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT 20 RELEASED FOR PUBLICATION BY TYCO ELECTRONICS CORPORATION. PACIFIC VERSION TERMINATOR INTERFACE ADAPTER PART NUMBER 4 3 2 20 REVISION DESCRIPTION A 2- 2151591 -2 DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 5 SET UP GAUGE 2119599-1 ALL RIGHTS RESERVED. 2- 2151591 -1 D 6 FEED TYPE FINE CRIMP HEIGHT ADJUST A FINE CRIMP HEIGHT ADJUST PNEUMATIC FEED SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED PNEUMATIC 2- 2151591 -5 A FINE CRIMP HEIGHT ADJUST 2- 2151591 -7 A FINE CRIMP HEIGHT ADJUST NONE A CONVERT TO MECHANICAL SERVO LATCH PLATE 7- 2151591 -7 APPLICATOR STYLE CONVERSION CHART CRIMP TOOLING KIT - SERVO LATCH PLATE SMART APPLICATOR MECHANICAL FEED 4 PNEUMATIC FEED - - CRIMP WIRE INSUL SIZE 2119950-1 1338685-1 2161326-1 - 2119951-1 2119949-1 2119951-1 2161326-1 2119949-1 2119950-1 - - 5-18022-5 - 8- 2151591 -5 8- 2151591 -4 1338685-1 5-18022-5 - 8- 2151591 -5 - 8- 2151591 -4 1338685-1 5-18022-5 1338685-1 5-18022-5 - - - - 2119641-2 2119799-1 - - 1901094-3 2119653-2 1901094-3 - 2119653-2 2119641-2 - - - - 2168400-6 2168400-6 - - 2119799-1 - (QUANTITY 2) - - - - - (QUANTITY 2) - - - - - 2063440-1 - - - - - - - - TYPE APPLICATOR INSTRUCTIONS 408-10389 - - - TE TERMINAL TERMINAL DATA: 2.8mm RECEPTACLE UNSEALED TERMINAL NAME: WIRE STRIP LENGTH 4.80-5.60 mm [.189-.220 IN] C TERMINAL APPLICATION SPECIFICATION n 114-13013 - - TE CRIMP SPECIFICATION - INSULATION DIAMETER RANGE - 1.19-1.65 mm [.047-.065 IN] - - - - - TERMINALS APPLIED TE TERMINAL 1326030-5 TE TERMINAL C1__DWG_PN_1_0 1326029-5 C1__DWG_PN_1_1 C1__DWG_PN_2_0 TE TERMINAL C1__DWG_PN_3_0 TE TERMINAL - C1__DWG_PN_4_0 - C1__DWG_PN_2_1 - WIRE SIZE 22 AWG 0.35mm2 CRIMP HEIGHT mm [INCH] W1__DWG_WGAUGE_1 W1__DWG_WGAUGE_2 1.04+/-0.05 [.041+/-.002] 1.04+/-0.05 [.041+/-.002] CRIMP HEIGHT REFERENCE SETTING W1__DWG_CRIMP_HT_1 W1__DWG_CRIMP_HT_2 9.1 9.1 - 9 - W1__FA_SETTING_1 - W1__FA_SETTING_2 - 1 B 2 - *WARNING ON INSTALLATION, SET WIRE DISC, ITEM 40 TO LARGEST WIRE SIZE SETTING. USE OF SETTINGS BELOW MINIMUM REQUIRED CRIMP HEIGHT SETTING WILL CAUSE DAMAGE TO CRIMP TOOLING. RECOMMENDED SPARE PARTS - GREASE BEARING SURFACES LIGHTLY - 3. LUBRICATE DAILY PER THE APPLICATOR INSTRUCTION SHEET SUPPLIED WITH THE APPLICATOR. 4 - APPLICATOR SPECIFIC DATA TO BE ENTERED INTO BLANK MEMORY CHIP AT ASSEMBLY. SEE BELOW FOR PART NUMBER: MECHANICAL FEED WITH "SMART APPLICATOR" CONVERSION: 8PNEUMATIC FEED WITH "SMART APPLICATOR" CONVERSION: 8SERVO FEED WITH "FINE CRIMP HEIGHT ADJUST": 8- - 2151591 -4 2151591 -4 2151591 -5 - 5. ADJUSTMENT OF THE STRIPPER MAY BE REQUIRED WHEN MOVING THE APPLICATOR BETWEEN BENCH AND LEADMAKER APPLICATIONS. APPLY PART NUMBER 1-23419-5 LOCTITE TO THREADS OF ITEMS 62, 180 7 GREASE THREADS, GROOVE AND O-RING ON ITEMS 139 8 9 10 11 A - SPARE FEED CAM STORAGE LOCATION REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - 1 1 1 - - 1 1 - 1 1 - 1 1 1 1 1 1 - -77 -27 -25 -22 -21 240792-2 2119782-1 2119640-1 2079988-1 PART NO DRAG, TERMINAL FINE ADJUST HEAD ASM, PACIFIC STYLE PUSH ROD, AIR FEED BUSHING, LCH5-12, MISUMI DESCRIPTION 1 240792-2 1 2119782 1 2119640-1 1 2079988_GATD - 263 251 250 249 - ITEM NO Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 1 1 1 1 - 1 1 1 P LTR DESCRIPTION DATE SEE SHEET 1 1 1 1 1 1 1 - 2 1 REF - - - 1 - - 1 - 1 1 1 - - - - - 1 - - - 1 1 2 - 1 1 1 - 1 1 1 1-22279-3 2119082-8 2079764-1 2119083-1 7-18023-7 2168400-6 2119580-1 2063440-1 2119740-2 1901094-3 21045-3 994969-1 994970-2 240638-1 8-21084-1 2119641-2 2119798-2 2079383-8 2168400-5 2119653-2 1-2119656-0 2119650-1 2119092-2 3-23627-7 2119799-1 SEE NOTE 4 1633743-1 1-18028-2 2119944-1 455888-5 5-547505-2 854769-4 2119956-1 2119740-1 2168078-1 2119793-1 992763-5 5-18022-5 21028-2 1338685-1 1-2168083-0 5018030-1 811242-5 690753-2 18023-9 2119652-1 2079383-7 2119645-1 2119957-1 2119644-1 1752356-1 2079383-5 2161328-1 1-1320908-0 2119959-4 455888-3 1320928-2 2168083-2 1-18028-2 2119533-1 2119806-1 3-22280-3 1-356885-4 2119805-1 318707-1 4-1633711-6 2119780-7 238011-9 3-1633962-4 455888-9 8-1633588-3 1 - 1 1 REF REF REF - - 1 1 1 - 1 - 1 1 1 1 1 1 1 1 1 - 1 1 1 - - 1 1 1 - - 1 1 1 - - 1 1 1 - 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 2 - 1 1 1 1 - 1 1 1 - - 1 1 1 - 2 1 1 1 1 2 1 1 1 1 2 1 1 1 - 2 3 1 1 - 1 3 - 1 2 1 3 - 1 2 1 3 1 1 2 1 1 1 - 2 1 1 1 1 1 1 1 1 - 1 1 1 1 - 1 1 - 1 REF 1 - - 1 - - - 1 1 - 1 REF - 1 1 - - 1 1 - - 1 1 1 - 1 1 1 1 4 - 1 1 1 4 - 1 1 1 4 - - 1 1 4 1 1 1 1 - 1 1 1 1 1 1 THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. DIMENSIONS: mm & 2 of 4) 1 DWN APVD - - MATERIAL - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - SPRING, COMPRESSION CAM, SNAIL, INSULATION ADJUSTMENT WASHER, WAVE SPRING, CREST-TO-CREST RETAINER, INSULATION DIAL SCR, SKT HD CAP M3 X 4.0 SHCS, LOW HEAD, RoHS, M5 X 16 MECHANICAL FEED ASSEMBLY AIR FEED MODULE TAG,IDENTIFICATION SPACER, FEEDER RING, RETAIN, EXTERN, 3/16 CRESCENT MAGNET, RARE EARTH HIGH ENERGY COUNTER, MAGNETIC SPRING, FEED FINGER O-RING, .801 ID, .070 DIA. MAT. FEED CAM, AIR FEED DETENT PIN SCR, BHSC, RoHS (M4 X 16) SHCS, LOW HEAD, RoHS, M4 X 20 FEED CAM, POST FEED APPLICATOR BASIC ASSEMBLY, SF RAM, ASIAN STYLE, SIDE FEED BOLT, ADJUSTMENT PIN, RETAIN, GRVD, 3/16 X .854 HOLDER,FEED FINGER, AF MEMORY CHIP, PROGRAMMED SERVO FEED LATCH ASM WASHER, FLAT, REG M4 FEED FINGER ASSEMBLY,SF SPACER, CRIMPER SPRING, COMPRESSION HOLDER, INS DOCUMENTATION PACKAGE TAG,IDENTIFICATION SCREW, DRIVE, RH, RoHS, 2 x .188 LIMITER, ADJUSTMENT BOLT SCR, SET, SOC, CONE POINT, M3 x 4.0 SCR, HEX HD CAP, M4 X 6.0 PIN, SLOTTED SPRING .062 X .250 PAWL, FEED SCR, SKT HD CAP, RoHS, M4 X 10 NUT, HEX, REG, RoHS, M3 BUMPER, HOLD DOWN SPACER, TONKER SCR, SKT HD CAP M4 X 6.0 FEED CAM, PRE FEED SCR, BHSC, RoHS (M8 X 25) DISC, NUMBERED FA WIRE ADJUSTMENT APPLICATOR SHIM PACK RAM WASHER, PRECISION SUPPORT, TERMINAL SCR, BHSC, RoHS (M4 X 20) HEX HEAD, FLANGED, M5 x 8mm LONG SPACER, STRIP GUIDE ASSEMBLY, STRIP GUIDE SPACER, CRIMPER STRIP GUIDE SCR, SKT HD CAP, RoHS, M4 X 8.0 WASHER, FLAT, REG M4 STRIPPER, SIDE FEED INSERT, SHEAR SPRING, COMPRESSION STOP, SHEAR SHEAR HOLDER, FRONT FLOATING SHEAR, FRONT ANVIL, COMBINATION DEPRESSOR, SHEAR BLOCK, CRIMPER SPACER CRIMPER, INSULATION F PREMIUM SPACER, CRIMPER CRIMPER, WIRE PART NO -77 -27 -25 -22 -21 PACIFIC VERSION AMP 4805 REV 31MAR2000 - 1 & 152. CRIMP HEIGHT REFERENCE SETTING WAS THE SETTING USED WHEN THE APPLICATOR WAS QUALIFIED AT THE FACTORY. ADJUSTMENT MAY BE NECESSARY WHEN RUNNING APPLICATOR IN THE FIELD. - & 242. MAGNET MUST BE ORIENTED CORRECTLY IN ORDER TO PROPERLY ACTUATE THE COUNTER. TO CONVERT THE APPLICATOR TO A NON-CARRIER CUTTING STYLE, REMOVE ITEM 13 AND ATTACH TO THE LOCATION ON BACK SIDE OF THE HOUSING. REFER TO INSTRUCTION SHEET FOR ADDITIONAL INFORMATION. - 1 6 66 - 2063440-1 - 1.90 mm [.075] A PART NUMBERS REQUIRED F F 1.60 mm [.063] REVISIONS DIST - - APPLICATOR DATA LOC 1 DWN 28MAR2013 CHK 28MAR2013 APVD 28MAR2013 C.CHEN C.CHEN I.CRUZ NAME SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 1 2119083 1 7-18023-7 2 2168400-6 1 2119580-1 1 2063440-1 1 2119740-2 .. 1 1901094-3 2 21045-3 1 994969-1_GATD 1 COUNTER_994970 1 240638 1 8-21084-1_GATD 1 2119641-2 1 2119798-2 1 2079383-8 4 2168400-5 1 2119653-2 1 1-2119656-0 1 2119650 1 2119092-2 1 3-23627-7 1 2119799 1 1901689_EMPTY_OCEAN_SF .. 1 1633743-1 1 1-18028-2 1 2119944-1 1 455888-5 1 SIMP_5-547505-2 1 854769-4 1 2119956-1 1 2119740-1 2 2168078-1 1 2119793 3 992763-5 1 5-18022-5 1 21028-2 1 1338685-1 2 1-2168083-0 1 5018030-1 1 811242-5_OLD 1 690753-2 3 18023-9 1 2119652 1 2079383-7 1 2119645 1 2119957-1 1 2119644-1 1 1752356-1 2 2079383-5 1 2161328 1 1-1320908-0 1 2119959-4 1 455888-3 1 1320928-2 1 2168083-2 1 1-18028-2 1 2119533 1 2119806 1 SIMP_3-22280-3 1 1-356885-4 1 2119805-1 1 318707-1 1 4-1633711-6 .. 1 ITEM_7 .. 1 ITEM_6 1 2119780-7 1 238011-9 1 3-1633962-4 1 455888-9 1 8-1633588-3 ITEM NO Harrisburg, PA 17105-3608 - WEIGHT 1 2079764 246 244 243 242 241 240 239 238 213 198 172 166 164 163 152 151 145 144 143 142 141 140 139 137 136 135 133 119 117 82 77 74 71 67 66 63 62 59 58 56 53 52 51 50 49 48 41 40 39 38 34 33 32 30 29 28 24 21 20 19 13 12 11 10 9 8 7 6 5 4 3 2 1 TE Connectivity APPLICATION SPEC - 1 2119082-8 DESCRIPTION PRODUCT SPEC - 1 1-22279-3_SIMP Ocean Side Feed Applicator - DRAWING NO 2151591 SCALE 1:1 RESTRICTED TO SHEET 3 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A D C B A 7 8 THIS DRAWING IS UNPUBLISHED. C COPYRIGHT RELEASED FOR PUBLICATION 5 4 3 2 20 LOC A ALL RIGHTS RESERVED. BY TYCO ELECTRONICS CORPORATION. 20 6 1 REVISIONS DIST 66 P LTR DESCRIPTION DATE SEE SHEET 1 - DWN APVD - - - FEED TYPE MECHANICAL 62 6 40 A DIMENSIONING AND TOLERANCING PER ASME Y14.5M-2009 D 251 145 38 239 246 39 59 7 56 140 152 250 249 8 238 A 2 166 242 2 6 63 50 163 2 243 53 2 D 244 7 139 PNEUMATIC 2 3.99 [ 0.157 ] REF 8 34 59 REF 136 82 137 C 1 52 172 56 TERMINAL SUPPORT LOCATION 1 C 2 51 3 SERVO LATCH PLATE 4 28 5 41 240 133 4 135 198 164 66 2 67 11 A 33 SERVO FEEDER NOT INCLUDED 58 19 10 74 20 9 21 29 117 REF 77 213 A 24 30 B 1 B 1 12 241 13 1 11 ITEM 30 LOCATED AT FRONT HOLES 263 30 CAM POSITIONS 30mm STROKE REF 29 30mm STROKE 30mm STROKE 141 142 REF 32 34 143 8 1 144 143 10 1 119 11 151 FEED TRACK POSITION GUIDE BY INSULATION BARREL 48 A A THIS DRAWING IS A CONTROLLED DOCUMENT FOR TYCO ELECTRONICS CORPORATION IT IS SUBJECT TO CHANGE AND THE CONTROLLING ENGINEERING ORGANIZATION SHOULD BE CONTACTED FOR THE LATEST REVISION. PACIFIC VERSION 49 MECHANICAL POST FEED 49 MECHANICAL PRE FEED 49 AIR FEED Shown on sheets 3 of 4 & 4 of 4 (Atlantic version shown on sheets 1 of 4 DIMENSIONS: mm & 2 of 4) MATERIAL AMP 4805 REV 31MAR2000 - TOLERANCES UNLESS OTHERWISE SPECIFIED: 0.1 0.02 0.005 0.0005 0 PLC 1 PLC 2 PLC 3 PLC 4 PLC ANGLES FINISH - DWN 28MAR2013 CHK 28MAR2013 APVD 28MAR2013 C.CHEN C.CHEN I.CRUZ TE Connectivity Harrisburg, PA 17105-3608 NAME PRODUCT SPEC - APPLICATION SPEC - - WEIGHT SIZE - A1 CAGE CODE 00779 Customer Accessible Production Drawing SHEETS 1 Ocean Side Feed Applicator - DRAWING NO 2151591 SCALE 1:1 RESTRICTED TO SHEET 4 OF - 4 & 2 ARE NOT REQUIRED FOR PACIFIC VERSION REV A