CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead @Super low ESR, high temperature resistance @Large capacitance & Improved high ripple current capability @Rated voltage range : 2.5 to 25Vdc @2000 hours at 105C @Suitable for DC-DC converters, voltage regulators and decoupling applications For computer motherboards @Pb-free design ?SPECIFICATIONS Items Characteristics Category Temperature Range -55 to +105C Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current *Note 2.5 to 25Vdc P20% (M) Rated voltageB1.15V I=0.2CV (max.) Where, I : Leakage current (MA), C : Nominal capacitance (MF), V : Rated voltage (Vdc) Dissipation Factor (tane) 0.12 max. Low Temperature Characteristics Endurance Bias Humidity Test Surge Voltage Test Failure Rate (at 20C, 120Hz) (at 105C) (at 20C after 2 minutes) (at 20C, 120Hz) Max. impedance ratio at 100kHz to the 20C value Z(-25C)/Z(+20C)[1.15 Z(-55C)/Z(+20C)[1.25 The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2000 hours at 105C. Appearance No significant damage Capacitance change [P20% of the initial measured value D.F. (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to DC voltage at 60C, 90 to 95% RH for 500 hours. Appearance No significant damage Capacitance change [P20% of the initial measured value D.F. (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The capacitors shall be subjected to 1000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change [P20% of the initial measured value D.F. (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value 1% per 1000 hours maximum (Confidence level 60% at 105C) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105C. ?DIMENSIONS [mm] ?MARKING @Terminal Code : E FP0.5 EX) 4V820MF F0.6 FD+0.5max. Coated Case PS18M 820 4V fD L F L+1.5 max. 15min. 8 11.5 3.5 10 12.5 5.0 4min. (1/2) CAT. No. E1001E CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead ?PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PS- AAA E AA AAA M AAA S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 270MF:271,1500MF:152) Lead forming·Taping code Terminal code Voltage code (ex. 4V:4R0,6.3V:6R3,10V:100) Series code Category Please refer to "A guide to global code (conductive polymer type)" ?STANDARD RATINGS WV(Vdc) 2.5 4 6.3 10 16 20 25 Cap(µF) 680 1500 560 820 390 680 270 470 180 330 100 150 68 100 Case size fDbL(mm) ESR (momax/20c, 100k to 300kHz) Rated ripple current (mArms/105c, 100kHz) 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 8B11.5 10B12.5 10 8 10 8 12 10 14 12 16 14 24 20 24 20 5230 5500 5230 5500 4770 5500 4420 5300 4360 5050 3320 4320 3320 4320 Part No. APS-2R5ESS681MHB5S APS-2R5ESS152MJC5S APS-4R0ESS561MHB5S APS-4R0ESS821MJC5S APS-6R3ESS391MHB5S APS-6R3ESS681MJC5S APS-100ESS271MHB5S APS-100ESS471MJC5S APS-160ESS181MHB5S APS-160ESS331MJC5S APS-200ESS101MHB5S APS-200ESS151MJC5S APS-250ESS680MHB5S APS-250ESS101MJC5S SS : Lead forming code and taping code (2/2) CAT. No. E1001E