FEATURES SIMPLIFIED FUNCTIONAL BLOCK DIAGRAM Controls supply voltages from 4 V to 60 V Gate drive for low voltage drop reverse supply protection Gate drive for P-channel FETs Inrush current limiting control Adjustable current limit Foldback current limiting Automatic retry or latch-off on current fault Programmable current-limit timer for safe operating area (SOA) Power-good and fault outputs Analog undervoltage (UV) and overvoltage (OV) protection 16-lead, 3 mm × 3 mm LFCSP 16-lead QSOP APPLICATIONS VCC/SENSE+ SENSE– RPFG ADM1270 VCAP LDO UV + – IOUT 1V – GATE DRIVE/ LOGIC 1V + REF SELECT FLB + CURRENTLIMIT CONTROL GENERAL DESCRIPTION The ADM1270 is a current-limiting controller that provides inrush current limiting and overcurrent protection for modular or battery-powered systems. When circuit boards are inserted into a live backplane, discharged supply bypass capacitors draw large transient currents from the backplane power bus as they charge. These transient currents can cause permanent damage to connector pins, as well as dips on the backplane supply that can reset other boards in the system. GATE – OV ISET Industrial modules Battery-powered/portable instrumentation + CURRENT LIMIT FB_PG – TIMER ON TIMER TIMEOUT VCB ENABLE FAULT PWRGD GND TIMER_OFF TIMER 12259-001 Data Sheet High Voltage Input Protection Device ADM1270 Figure 1. The ADM1270 is designed to control the inrush current, when powering on the system, via an external P-channel field effect transistor (FET). To protect the system from a reverse polarity input supply, there is a provision made to control an additional external P-channel FET. This feature prevents reverse current flow in case of a reverse polarity connection, which can damage the load or the ADM1270. The ADM1270 is available in a 3 mm × 3 mm, 16-lead LFCSP and a 16-lead QSOP. Rev. A Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 ©2014–2016 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADM1270 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Current Sense Inputs ................................................................. 16 Applications ....................................................................................... 1 Current-Limit Reference ........................................................... 16 General Description ......................................................................... 1 Setting the Current Limit (ISET) ............................................. 16 Simplified Functional Block Diagram ........................................... 1 Foldback ...................................................................................... 17 Revision History ............................................................................... 2 TIMER ......................................................................................... 17 Specifications..................................................................................... 3 TIMER_OFF ............................................................................... 18 Absolute Maximum Ratings ............................................................ 5 Hot Swap Retry Duty Cycle ...................................................... 18 Thermal Characteristics .............................................................. 5 Gate and RPFG Clamps ............................................................. 19 ESD Caution .................................................................................. 5 Fast Response to Severe Overcurrent ...................................... 19 Pin Configurations and Function Descriptions ........................... 6 Undervoltage and Overvoltage ................................................. 19 Typical Performance Characteristics ............................................. 9 Enable Input ................................................................................ 19 Typical Application Circuit ........................................................... 14 Power Good ................................................................................ 20 Theory of Operation ...................................................................... 15 Outline Dimensions ....................................................................... 21 Powering the ADM1270 ............................................................ 16 Ordering Guide .......................................................................... 21 REVISION HISTORY 4/16—Rev. 0 to Rev. A Change to Setting the Current Limit (ISET) Section ................. 17 12/14—Revision 0: Initial Version Rev. A | Page 2 of 21 Data Sheet ADM1270 SPECIFICATIONS VCC/VSENSE+ = 4 V to 60 V, VSENSE = (VSENSE+ − VSENSE−) = 0 V, TA = −40°C to +125°C, unless otherwise noted. Table 1. Parameter POWER SUPPLY Operating Voltage Range Quiescent Current UV PIN Input Current Symbol Min VCC ICC 4 IUV Max Unit Test Conditions/Comments 360 60 500 V μA GATE on 0.2 1 1.015 65 7 8 μA μA V mV μs μs UV ≤ 5.5 V, TA = −40°C to +85°C UV ≤ 5.5 V, TA = −40°C to +125°C UV falling μA μA V mV μs μs OV ≤ 5.5 V, TA = −40°C to +85°C OV ≤ 5.5 V, TA = −40°C to +125°C OV rising 1.5 0.2 1 1.015 35 2.0 2.5 0.005 0.005 1.0 60 UV Threshold UV Threshold Hysteresis UV Glitch Filter UV Propagation Delay OV PIN Input Current UVTH UVHYST UVGF UVPD OV Threshold OV Threshold Hysteresis OV Glitch Filter OV Propagation Delay SENSE− Input Current VCAP PIN Internally Regulated Voltage Undervoltage Lockout Rising Falling Hysteresis ISET PIN Input Current OVTH OVHYST OVGF OVPD 0.985 25 0.5 ISENSE− 20 40 70 μA SENSE− = 60 V VVCAP UVLO UVLORISE UVLOFALL UVLOHYST 3.546 3.6 3.636 V 0 μA ≤ IVCAP ≤ 1 mA, CVCAP = 1 μF 3.4 V V mV VCC rising VCC falling Reference Select Threshold Internal Reference VISETRSTH VCLREF 0.2 1 2.65 μA μA V V Gain of Current Sense Amplifier AVCSAMP 40 V/V VISET ≤ VVCAP, TA = −40°C to +85°C VISET ≤ VVCAP, TA = −40°C to +125°C If VISET > VISETRSTH, an internal reference (VCLREF) is used Accuracies included in total sense voltage accuracies Accuracies included in total sense voltage accuracies VRPFG 0 V VCC ≤ 10 V RPFG PIN Reverse Protection FET Gate Drive Voltage Reverse Protection FET Gate Drive Voltage Offset RPFG Pull-Down (On) Current GATE PIN GATE Drive Voltage GATE Pull-Down (On) Current GATE Pull-Up (Off ) Current Regulation Fault 0.985 55 4 Typ 6 IOV 0.005 0.005 1.0 30 3.0 230 IISET 2.55 0.005 0.005 2.6 2 50 mV overdrive UV low to GATE pull-down circuit active 50 mV overdrive OV high to GATE pull-up circuit active ΔVRPFG 10 12 14 V ΔVRPFG = VCC − VRPFG, 60 V ≥ VCC ≥ 14 V, IRPFG ≤ 5 μA IRPFGND 7 9 12 μA VRPFG = VCC ΔVGATE IGATEDN IGATEUP IGATEUP_REG IGATEUP_FLT 10 20 12 25 14 30 V μA ΔVGATE = VCC − VGATE, 60 V ≥ VCC ≥ 14 V, IGATE ≤ 5 μA VGATE = VCC −50 −7 −65 −13 −80 −20 μA mA ΔVGATE ≥ 2 V, (VSENSE+ − VSENSE−) = 70 mV ΔVGATE = 2 V Rev. A | Page 3 of 21 ADM1270 Parameter CURRENT SENSE VOLTAGE Sense Voltage Current Limit (VSENSE+ − VSENSE−) Foldback Inactive Data Sheet Symbol Min Typ Max Unit Test Conditions/Comments VSENSECL 47 50 53 mV VISET > 2.65 V, VFLB > 1.1 V, ΔVGATE = 3 V, IGATE = 0 µA VCBOS 47 22.5 10.0 7 22 0.5 62.5 50 25.0 12.5 10 25 1 53 27.5 15.0 13 28 1.5 mV mV mV mV mV mV mV VISET = 2.5 V, VFLB > 1.35 V, ΔVGATE = 3 V, IGATE = 0 µA VISET = 2 V, VFLB > 1.1 V, ΔVGATE = 3 V, IGATE = 0 µA VISET = 1 V, VFLB > 0.57 V, ΔVGATE = 3 V, IGATE = 0 µA VISET = 0.5 V, VFLB > 0.3 V, ΔVGATE = 3 V, IGATE = 0 µA VFLB = 0 V, ΔVGATE = 3 V, IGATE = 0 µA VISET > 2 V, VFLB = 0.5 V, ΔVGATE = 3 V, IGATE = 0 µA Circuit breaker trip voltage, VCB = VSENSECL − VCBOS 110 30 1.6 3.5 mV mV µs µs VISET > 2.65 V VISET = 0.5 V −22 2.04 0.12 1.15 105 µA V V µA µA Overcurrent fault, 0.2 V ≤ VTIMER ≤ 2 V Foldback Active Circuit Breaker Offset SEVERE OVERCURRENT Voltage Threshold Glitch Filter Duration Response Time TIMER PIN TIMER Pull-Up Current TIMER High Threshold TIMER Low Threshold TIMER Pull-Down Current TIMER_OFF PIN Power-On Reset Pull-Up Current Retry Pull-Up Current TIMER_OFF High Threshold FOLDBACK (FLB PIN) Input Current PWRGD FEEDBACK INPUT (FB_PG PIN) Input Current PWRGD Rising Threshold PWRGD Threshold Hysteresis Power-Good Glitch Filter FAULT PIN Output Low Voltage Leakage Current ENABLE PIN Input High Voltage Input Low Voltage Leakage Current PWRGD PIN Output Low Voltage Output Low Voltage Leakage Current VSENSEOC 90 20 0.4 100 25 2.0 ITIMERUP VTIMERH VTIMERL ITIMERPD −18 1.96 0.075 0.85 75 −20 2.0 0.10 IPOR ITMROFF VTMROFFH −18 −0.85 1.96 −20 −1 2.0 −22 −1.15 2.04 µA µA V Initial power-on reset, VTIMER_OFF = 1 V After fault when GATE is off, VTIMER_OFF = 1 V IFLB 0.005 0.005 0.2 1 µA µA VFLB ≤ 5.5 V, TA = −40°C to +85°C VFLB ≤ 5.5 V, TA = −40°C to +125°C IFBPG 0.005 0.005 1.0 30 0.2 1 1.015 35 1.5 µA µA V mV µs VFB_PG ≤ 5.5 V, TA = −40°C to +85°C VFB_PG ≤ 5.5 V, TA = −40°C to +125°C FB_PG rising 0.005 0.1 0.4 1 V V µA IFAULT = 100 µA IFAULT = 1 mA VFAULT = 5.5 V, FAULT output high-Z 0.005 0.4 1 V V µA VEN = 5.5 V 0.005 0.1 0.4 0.4 1 V V V µA IPWRGD = 100 µA IPWRGD = 1 mA VCC = 1.7 V, ISINK = 100 µA, VPWRGD = 60 V, PWRGD output high-Z VPGTH PGHYST PGGF 0.985 25 0.5 VOL_FAULT IFAULT VIH VIL IEN 1.2 VOL_PWRGD VOL_PWRGD IPWRGD Rev. A | Page 4 of 21 Timer pin voltage = 0.2 V Timer pin voltage = 0.05 V 50 mV overdrive Data Sheet ADM1270 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter VCC/SENSE+ VCAP UV OV ISET FLB FB_PG TIMER_OFF TIMER FAULT ENABLE PWRGD GATE GATE to VCC/SENSE+ SENSE− RPFG RPFG to VCC/SENSE+ VSENSE (VSENSE+ − VSENSE−) Continuous Current into Any Pin Storage Temperature Range Operating Temperature Range Lead Temperature, Soldering (10 sec) Junction Temperature Rating −0.3 V to +66 V −0.3 V to +6 V −0.3 V to +6 V −0.3 V to +6 V −0.3 V to VCAP + 0.3 V −0.3 V to +6 V −0.3 V to +6 V −0.3 V to VCAP + 0.3 V −0.3 V to VCAP + 0.3 V −0.3 V to +6 V −0.3 V to +6 V −0.3 V to +66 V −0.3 V to VCC + 0.3 V −22 V to +0.3 V −0.3 V to VCC + 0.3 V −0.3 V to VCC + 0.3 V −22 V to +0.3 V ±0.3 V ±10 mA −65°C to +150°C −40°C to +125°C 300°C 150°C Stresses at or above those listed under Absolute Maximum Ratings may cause permanent damage to the product. This is a stress rating only; functional operation of the product at these or any other conditions above those indicated in the operational section of this specification is not implied. Operation beyond the maximum operating conditions for extended periods may affect product reliability. THERMAL CHARACTERISTICS θJA is specified for the worst-case conditions, that is, a device soldered in a circuit board for surface-mount packages. Table 3. Thermal Resistance Package Type 16-Lead, 3 mm × 3 mm LFCSP 16-Lead QSOP ESD CAUTION Rev. A | Page 5 of 21 θJA 49.5 106.03 θJC 35.2 28.31 ΨJB 29.6 43.22 Unit °C/W °C/W ADM1270 Data Sheet 13 GATE 14 SENSE– 16 RPFG 15 VCC/SENSE+ PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS VCAP 1 12 PWRGD 11 FLB ADM1270 TOP VIEW UV 3 10 FB_PG 9 GND 7 TIMER_OFF TIMER 8 FAULT 6 ENABLE 5 OV 4 NOTES 1. THE EXPOSED PAD IS LOCATED ON THE UNDERSIDE OF THE LFCSP PACKAGE. SOLDER THE EXPOSED PAD TO THE PRINTED CIRCUIT BOARD (PCB) TO IMPROVE THERMAL DISSIPATION. THE EXPOSED PAD CAN BE CONNECTED TO GROUND. 12259-002 ISET 2 Figure 2. 16-Lead LFCSP Pin Configuration Table 4. 16-Lead LFCSP Pin Function Descriptions Pin No. 1 Mnemonic VCAP 2 ISET 3 UV 4 OV 5 ENABLE 6 FAULT 7 8 GND TIMER 9 TIMER_OFF 10 FB_PG 11 FLB 12 PWRGD 13 GATE 14 SENSE− Description Internal Regulated Supply. Place a capacitor with a 1 µF or greater value on this pin to maintain good accuracy. This pin can be used as a reference to program the ISET pin voltage. Current Limit. This pin allows the current-limit threshold to be programmed. The default limit is set when this pin is connected directly to VCAP. To achieve a user defined sense voltage, the current limit can be adjusted using a resistor divider from VCAP. An external reference can also be used. Undervoltage Input Pin. An external resistor divider is connected from the supply to this pin to allow an internal comparator to detect whether the supply is under the UV limit. Overvoltage Input Pin. An external resistor divider is connected from the supply to this pin to allow an internal comparator to detect whether the supply is above the OV limit. Enable Pin. This pin is a digital logic input. This input must be high to allow the ADM1270 controller to begin a power-up sequence. If this pin is held low, the ADM1270 is prevented from powering up. There is no internal pullup on this pin. Fault Output. This pin indicates that the device has shut down due to an overcurrent fault condition. The device can be configured for automatic retry after shutdown by connecting this pin directly to the ENABLE pin. Ground Pin. Timer Pin. An external capacitor, CTIMER, sets an SOA overcurrent fault delay. The GATE pin is pulled off when the voltage on the TIMER pin exceeds the upper threshold. Timer Off Pin. An external capacitor, CTIMER_OFF, sets an initial timing cycle delay and the SOA off time delay. After an SOA overcurrent fault has occurred, the GATE pin is pulled off until the voltage on the TIMER_OFF pin exceeds the threshold. PWRGD Feedback Input Pin. An external resistor divider is connected from the output voltage to this pin to allow an internal comparator to detect when the output voltage is above the PWRGD threshold. Foldback Pin. A foldback resistor divider is placed from the source of the FET to this pin. Foldback reduces the current limit when the source voltage drops. The foldback feature ensures that the power through the FET is not increased beyond the SOA limits. Power-Good Signal. This signal indicates that the supply is within tolerance. This signal is based on the voltage present on the FB_PG pin. Gate Output Pin. This pin is the gate drive of an external P-channel FET. This pin is driven by the FET drive controller, which provides a pull-down current to charge the FET gate pin. The FET drive controller regulates to a maximum load current by regulating the GATE pin. GATE is held off when the supply is below the undervoltage lockout (UVLO). Negative Current Sense Input Pin. A sense resistor between the VCC/SENSE+ pin and the SENSE− pin sets the analog current limit. The hot swap operation of the ADM1270 controls the external FET gate to maintain the sense voltage (VSENSE+ − VSENSE−). This pin also connects to the FET drain pin. Rev. A | Page 6 of 21 Data Sheet Pin No. 15 Mnemonic VCC/SENSE+ 16 RPFG N/A1 EP 1 ADM1270 Description Positive Supply Input Pin (VCC). A UVLO circuit resets the device when a low supply voltage is detected. GATE is held off when the supply is below UVLO. No sequencing is required. Positive Current Sense Input Pin (SENSE+). This pin connects to the main supply input. A sense resistor between the VCC/SENSE+ pin and the SENSE− pin sets the analog current limit. The hot swap operation of the ADM1270 controls the external FET gate to maintain the sense voltage (VSENSE+ − VSENSE−). Reverse Protection FET Gate Driver Output. Connect this pin to the gate of the external reverse polarity protection P-channel FET for low voltage drop operation. Exposed Pad. The exposed pad is located on the underside of the LFCSP package. Solder the exposed pad to the printed circuit board (PCB) to improve thermal dissipation. The exposed pad can be connected to ground. N/A = not applicable. Rev. A | Page 7 of 21 Data Sheet VCC/SENSE+ 1 16 SENSE– RPFG 2 15 GATE VCAP 3 14 PWRGD ISET 4 ADM1270 13 FLB UV 5 TOP VIEW (Not to Scale) 12 FB_PG OV 6 11 TIMER_OFF ENABLE 7 10 TIMER FAULT 8 9 GND 12259-003 ADM1270 Figure 3. 16-Lead QSOP Pin Configuration Table 5. 16-Lead QSOP Pin Function Descriptions Pin No. 1 Mnemonic VCC/SENSE+ 2 RPFG 3 VCAP 4 ISET 5 UV 6 OV 7 ENABLE 8 FAULT 9 10 GND TIMER 11 TIMER_OFF 12 FB_PG 13 FLB 14 PWRGD 15 GATE 16 SENSE− Description Positive Supply Input Pin (VCC). A UVLO circuit resets the device when a low supply voltage is detected. GATE is held off when the supply is below UVLO. No sequencing is required. Positive Current Sense Input Pin (SENSE+). This pin connects to the main supply input. A sense resistor between the VCC/SENSE+ pin and the SENSE− pin sets the analog current limit. The hot swap operation of the ADM1270 controls the external FET gate to maintain the sense voltage (VSENSE+ − VSENSE−). Reverse Protection FET Gate Driver Output. Connect this pin to the gate of the external reverse polarity protection P-channel FET for low voltage drop operation. Internal Regulated Supply. Place a capacitor with a 1 μF or greater value on this pin to maintain good accuracy. This pin can be used as a reference to program the ISET pin voltage. Current Limit. This pin allows the current-limit threshold to be programmed. The default limit is set when this pin is connected directly to VCAP. To achieve a user defined sense voltage, the current limit can be adjusted using a resistor divider from VCAP. An external reference can also be used. Undervoltage Input Pin. An external resistor divider is connected from the supply to this pin to allow an internal comparator to detect whether the supply is under the UV limit. Overvoltage Input Pin. An external resistor divider is connected from the supply to this pin to allow an internal comparator to detect whether the supply is above the OV limit. Enable Pin. This pin is a digital logic input. This input must be high to allow the ADM1270 controller to begin a power-up sequence. If this pin is held low, the ADM1270 is prevented from powering up. There is no internal pullup on this pin. Fault Output. This pin indicates that the device has shut down due to an overcurrent fault condition. The device can be configured for automatic retry after shutdown by connecting this pin directly to the ENABLE pin. Ground Pin. Timer Pin. An external capacitor, CTIMER, sets an SOA overcurrent fault delay. The GATE pin is pulled off when the voltage on the TIMER pin exceeds the upper threshold. Timer Off Pin. An external capacitor, CTIMER_OFF, sets an initial timing cycle delay and the SOA off time delay. After an SOA overcurrent fault has occurred, the GATE pin is pulled off until the voltage on the TIMER_OFF pin exceeds the threshold. PWRGD Feedback Input Pin. An external resistor divider is connected from the output voltage to this pin to allow an internal comparator to detect when the output voltage is above the PWRGD threshold. Foldback Pin. A foldback resistor divider is placed from the source of the FET to this pin. Foldback reduces the current limit when the source voltage drops. The foldback feature ensures that the power through the FET is not increased beyond the SOA limits. Power-Good Signal. This signal indicates that the supply is within tolerance. This signal is based on the voltage present on the FB_PG pin. Gate Output Pin. This pin is the gate drive of an external P-channel FET. This pin is driven by the FET drive controller, which provides a pull-down current to charge the FET gate pin. The FET drive controller regulates to a maximum load current by regulating the GATE pin. GATE is held off when the supply is below UVLO. Negative Current Sense Input Pin. A sense resistor between the VCC/SENSE+ pin and the SENSE− pin sets the analog current limit. The hot swap operation of the ADM1270 controls the external FET gate to maintain the sense voltage (VSENSE+ − VSENSE−). This pin also connects to the FET drain pin. Rev. A | Page 8 of 21 Data Sheet ADM1270 TYPICAL PERFORMANCE CHARACTERISTICS 3.65 500 LOAD = 100µA LOAD = 500µA LOAD = 1mA LOAD = 100µA LOAD = 500µA LOAD = 1mA 450 400 3.63 3.61 ICC (µA) VVCAP (V) 350 300 250 200 3.59 150 100 3.57 50 25°C –5°C 85°C 125°C 0 TJ (°C) –40°C 25°C –5°C 85°C 12259-007 –40°C 12259-004 3.55 125°C TJ (°C) Figure 4. VVCAP vs. Junction Temperature (TJ), Different Loads Figure 7. Supply Current (ICC) vs. Junction Temperature (TJ), Different Loads 400 3.610 398 396 3.605 ICC (µA) VVCAP (V) 394 3.600 392 390 388 386 3.595 384 0 0.2 0.4 0.6 0.8 1.0 ILOAD (mA) 380 12259-005 3.590 0 0.2 0.6 0.4 0.8 1.0 ILOAD (mA) Figure 5. VVCAP vs. Load Current (ILOAD) 12259-008 382 Figure 8. Supply Current (ICC) vs. Load Current (ILOAD) 420 3.610 LOAD = 100µA LOAD = 500µA LOAD = 1mA LOAD = 100µA LOAD = 500µA LOAD = 1mA 400 3.605 ICC (µA) 3.600 360 340 3.595 3.590 0 10 20 30 40 VIN (V) 50 Figure 6. VVCAP vs. Input Voltage (VIN), Different Loads 300 0 10 30 20 VCC (V) 40 50 12259-009 320 12259-006 VVCAP (V) 380 Figure 9. Supply Current (ICC) vs. Supply Voltage (VCC), Different Loads Rev. A | Page 9 of 21 ADM1270 16 14 12 10 8 6 4 –10 10 30 70 50 90 110 130 9.2 9.0 8.8 8.6 8.4 –40 –20 20 0 40 60 80 100 120 140 TEMPERATURE (°C) Figure 10. VVCAP Overcurrent (OC) Threshold vs. Temperature, Different Input Voltages Figure 13. RPFG Pull-Down Current (IRPFGND) vs. Temperature, Different Input Voltages 0.070 13.0 4V 25V 50V CURRENT SENSE VOLTAGE (V) VIN = 14V VIN = 25V VIN = 50V 12.6 12.4 VGATE (V) 9.4 8.0 –60 12259-010 –30 TEMPERATURE (°C) 12.8 9.6 8.2 2 0 –50 VIN = 14V VIN = 25V VIN = 50V 9.8 12259-013 VVCAP OC THRESHOLD (mA) 18 10.0 VIN = 4.5V VIN = 6V VIN = 10V RPFG PULL-DOWN CURRENT (µA) 20 Data Sheet 12.2 12.0 11.8 11.6 11.4 0.065 0.060 0.055 0.050 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 0.045 2.50 RPFG VOLTAGE (V) 12.6 12.4 12.2 12.0 11.8 11.6 11.4 11.0 –60 –40 –20 0 20 40 60 TEMPERATURE (°C) 80 100 120 140 12259-012 11.2 Figure 12. RPFG Voltage (VRPFG) vs. Temperature, Different Input Voltages 2.56 2.58 2.60 2.62 2.64 2.66 2.68 2.70 Figure 14. Current Sense Voltage vs. ISET Voltage (VISET), Different Input Voltages REFERENCE SELECT THRESHOLD VOLTAGE (V) 12.8 VIN = 14V VIN = 25V VIN = 50V 2.54 VISET (V) Figure 11. GATE Voltage (VGATE) vs. Temperature, Different Input Voltages 13.0 2.52 2.65 2.60 2.55 2.50 –60 –40 –20 0 20 40 60 TEMPERATURE (°C) 80 100 120 140 12259-015 –40 12259-011 11.0 –60 12259-014 11.2 Figure 15. Reference Select Threshold Voltage (VISETRSTH) vs. Temperature, VIN = 4 V Rev. A | Page 10 of 21 Data Sheet ADM1270 –18.0 –40°C –5°C +25°C +85°C +125°C 0.065 –40°C –5°C +25°C +85°C +125°C –18.5 POR TIMER OFF CURRENT (µA) REFERENCE SELECT THRESHOLD VOLTAGE (V) 0.070 0.060 0.055 0.050 –19.0 –19.5 –20.0 –20.5 –21.0 2.52 2.54 2.60 2.58 2.56 2.64 2.62 2.66 2.68 2.70 VISET (V) –22.0 12259-016 0.045 2.50 –19.5 –20.0 –20.5 –21.0 –21.5 25 30 35 45 40 55 50 –19.0 –19.5 –20.0 –20.5 –21.0 –5 15 35 55 75 95 115 135 TEMPERATURE (°C) –22.0 –45 12259-017 –25 –0.7 15 35 55 75 95 115 135 Figure 20. POR Timer Off Current (IPOR) vs. Temperature, Different Input Voltages 7 4V 6V 10V 20V 50V –0.6 –5 TEMPERATURE (°C) Figure 17. Timer Current vs. Temperature, Different Input Voltages –0.5 –25 12259-020 –21.5 –22.0 –45 OV INPUT RISE OV INPUT FALL 6 5 –0.8 VGATE (V) –0.9 –1.0 –1.1 –1.2 4 3 2 –1.3 1 –1.4 –1.5 –45 –25 –5 15 35 55 75 95 115 TEMPERATURE (°C) 135 12259-018 TIMER OFF CURRENT (µA) 20 Figure 18. Timer Off Current (ITMROFF) vs. Temperature, Different Input Voltages 0 0.90 0.95 1.00 1.05 OV INPUT VOLTAGE (V) Figure 21. VGATE vs. OV Input Voltage Rev. A | Page 11 of 21 1.10 12259-021 TIMER CURRENT (µA) –19.0 15 4V 6V 10V 20V 50V –18.5 POR TIMER OFF CURRENT (µA) –18.5 10 Figure 19. POR Timer Off Current (IPOR) vs. Input Voltage (VIN), Different Temperatures –18.0 4V 6V 10V 20V 50V 5 INPUT VOLTAGE (V) Figure 16. Reference Select Threshold Voltage (VISETRSTH) vs. ISET Voltage (VISET), Different Temperatures –18.0 0 12259-019 –21.5 ADM1270 Data Sheet 0.970 0.04 0.03 1.00 0.02 0.01 UV RISE UV FALL HYSTERESIS 0.95 –60 –40 –20 HYSTERESIS (V) 1.05 0 20 40 60 80 100 0 140 120 TEMPERATURE (°C) 4V POWER-GOOD FALL 25V POWER-GOOD FALL 50V POWER-GOOD FALL 0.965 0.960 0.955 0.950 –60 12259-022 UV THRESHOLD VOLTAGE (V) 0.05 POWER-GOOD FALLING THRESHOLD (V) 0.06 –40 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) Figure 22. UV Threshold Voltage vs. Temperature 12259-025 1.10 Figure 25. Power-Good Falling Threshold vs. Temperature, Different Input Voltages 1.05 0.03 0.108 0.02 0.01 0.95 SEVERE OC THRESHOLD (V) 1.00 HYSTERESIS (V) OV THRESHOLD VOLTAGE (V) 4V OV 25V OC 50V OC 0.106 0.104 0.102 –40 –20 0 40 20 100 80 60 120 0 140 TEMPERATURE (°C) 0.100 –60 12259-023 0.90 –60 0 20 40 60 80 100 120 140 Figure 26. Severe Overcurrent (OC) Threshold vs. Temperature, Different Input Voltages 0.07 4V POWER-GOOD RISE 25V POWER-GOOD RISE 50V POWER-GOOD RISE –40°C –5°C –25°C –85°C –125°C 0.06 0.995 VSENSE (V) 0.05 0.990 0.04 0.03 0.02 0.985 0.980 –60 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) 140 Figure 24. Power-Good Rising Threshold vs. Temperature, Different Input Voltages 0 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 FLB (V) Figure 27. Sense Voltage (VSENSE ) vs. FLB, Different Temperatures Rev. A | Page 12 of 21 12259-027 0.01 12259-024 POWER-GOOD RISING THRESHOLD (V) –20 TEMPERATURE (°C) Figure 23. OV Threshold vs. Temperature 1.000 –40 12259-026 OV RISE OV FALL HYSTERESIS Data Sheet 0.07 ADM1270 2.02 0.06 OC TIMER THRESHOLD (V) –40°C –5°C +25°C +85°C +125°C VSENSE (V) 0.05 0.04 0.03 0.02 4V 50V 2.01 2.00 1.99 0 0.5 1.0 1.5 2.0 2.5 3.5 3.0 VISET (V) Figure 28. Sense Voltage (VSENSE) vs. ISET Voltage (VISET), Different Temperatures 50 –20 0 20 40 60 80 100 120 140 TEMPERATURE (°C) 2.01 OC TIMER_OFF THRESHOLD (V) OC INPUT CURRENT (µA) 40 –40 Figure 31. OC TIMER Threshold vs. Temperature, Different Input Voltages 10mV 20mV 30mV 40mV 50mV 60mV 45 1.98 –60 12259-028 0 12259-031 0.01 35 30 25 20 15 10 4V 50V 2.00 1.99 1.98 –40 –20 0 40 20 60 80 100 120 140 TEMPERATURE (°C) Figure 29. OC Input Current vs. Temperature, Different Sense Voltages (VSENSE) 50 45 35 30 25 20 15 –40°C –5°C +25°C +85°C +125°C 10 5 0 0 0.5 1.0 1.5 2.0 VSENSE (V) 2.5 3.0 3.5 12259-030 OC INPUT CURRENT (µA) 40 Figure 30. OC Input Current vs. Sense Voltage (VSENSE), Different Temperatures Rev. A | Page 13 of 21 1.97 –60 –40 –20 0 20 40 60 80 100 120 TEMPERATURE (°C) Figure 32. OC TIMER_OFF Threshold vs. Temperature, Different Input Voltages 140 12259-032 0 –60 12259-029 5 ADM1270 Data Sheet TYPICAL APPLICATION CIRCUIT RSENSE VIN VOUT VCC/SENSE+ Q2 SENSE– Q1 RPFG LOAD VCAP LDO + R1 – IOUT UV + 1V R2 OV – GATE DRIVE/ LOGIC GATE – 1V + R4 R8 FLB REF SELECT + R7 FB_PG CURRENTLIMIT CONTROL R3 CURRENT LIMIT – TIMER ON R5 TIMER_OFF R9 TIMER TIMEOUT ENABLE FAULT TIMER VCB PWRGD GND Figure 33. Typical Application Circuit Rev. A | Page 14 of 21 CTIMER CTIMER_OFF 12259-033 ISET Data Sheet ADM1270 THEORY OF OPERATION connected to the TIMER pin and the TIMER_OFF pin. This current-limit time helps to maintain the FET in its SOA. When circuit boards are inserted into a live backplane, discharged supply bypass capacitors draw large transient currents from the backplane power bus as they charge. These transient currents can cause permanent damage to connector pins, as well as voltage dips on the backplane supply that can reset other boards in the system. In addition to the timer function, there is a foldback pin (FLB) that is used to provide additional FET protection. The current limit is linearly reduced by the voltage on the FLB pin, so that for large drain to source voltage (VDS) voltage drops, the actual current limit used by the device is lower, again helping to ensure the FET is kept within its SOA. The ADM1270 is designed to control the inrush current when powering on the system, allowing a board to be inserted safely into a live backplane by protecting it from excess currents. A minimum voltage clamp ensures that even if the FLB voltage is 0 V, the current is never reduced to zero, which otherwise prevents the device from powering up. The ADM1270 is a current-limiting controller that provides inrush current limiting and overcurrent protection for modular or battery-powered systems. The voltage developed across a sense resistor in the power path is measured with a current sense amplifier via the VCC/SENSE+ and SENSE− pins. A default limit of 50 mV is set, but this limit can be adjusted, if required, using a resistor divider network from the VCAP pin to the ISET pin. The ADM1270 features OV and UV protection, programmed using external resistor dividers on the UV and OV pins. A PWRGD signal can be used to indicate when the output supply is greater than a voltage programmed using an external resistor divider on the FB_PG pin. To protect the system from a reverse polarity input supply, there is a provision made to control an additional external P-channel FET with the RPFG pin. This feature allows for a low on-resistance, low voltage drop FET to be used in place of a diode to perform the same function, thus saving power losses and improving overall efficiency. The reverse voltage protection FET prevents negative input voltages that can damage the load or the ADM1270. The ADM1270 limits the current through the sense resistor by controlling the gate voltage of an external P-channel FET in the power path, via the GATE pin. The sense voltage and, therefore, the load current is maintained below the preset maximum. The ADM1270 protects the external FET by limiting the time that the FET remains on while the current is at its maximum value. This current-limit time is set by the choice of capacitors VCC/SENSE+ SENSE– RPFG ADM1270 VCAP LDO UV + + – IOUT 1V GATE DRIVE/ LOGIC GATE – 1V + REF SELECT FLB + CURRENTLIMIT CONTROL CURRENT LIMIT FB_PG – TIMER ON TIMER TIMEOUT VCB ENABLE FAULT PWRGD TIMER_OFF TIMER GND Figure 34. Simplified Functional Block Diagram Rev. A | Page 15 of 21 12259-034 OV ISET – ADM1270 Data Sheet POWERING THE ADM1270 CURRENT SENSE INPUTS The load current is monitored by measuring the voltage drop across an external current sense resistor, RSENSE (see Figure 35). An internal current sense amplifier provides a gain of 40 to the voltage drop detected across RSENSE. The result is compared to an internal reference and is used by the hot swap control logic to detect an overcurrent condition. RSENSE VCC/SENSE+ VCAP LDO SENSE– – Q1 + GATE – REFERENCE VCAP LDO SENSE– + Q1 – 40× 2V GATE REF SELECT ISET + CURRENTLIMIT CONTROL FLB CURRENT LIMIT – GND Figure 36. Current-Limit Reference Selection The FLB voltage varies during different modes of operation and, therefore, is clamped to a minimum level of 200 mV. This behavior prevents zero current flow due to the current limit being set too low. Figure 37 provides an example of how the FLB and ISET voltages interact during startup as the ADM1270 turns on the FET and charges the load capacitance. Depending on how the foldback feature is configured, the transition point varies to ensure that the FET operates within the correct limits. 40× + VCC/SENSE+ 12259-036 A supply voltage from 4 V to 60 V is required to power the ADM1270 via the VCC/SENSE+ pin. The VCC/SENSE+ pin provides the majority of the bias current for the device; the remainder of the current needed to control the gate drive and to best regulate the gate to source voltage (VGS) is supplied by the SENSE− pin. 4V TO 60V RSENSE 4V TO 60V VISET FLB CURRENT LIMIT 12259-035 2V GND ISET CURRENT-LIMIT REFERENCE Figure 35. Hot Swap Current Sense Amplifier CURRENT-LIMIT REFERENCE An internal current-limit reference selector block continuously compares the ISET and FLB voltages to determine which voltage is the lowest at any given time; the lowest voltage is used as the current-limit reference. This behavior ensures that the programmed current limit, ISET, is used in normal operation, and that the foldback feature reduces the current limit when required during startup and/or fault conditions. 0.2V TIME 12259-037 The current-limit reference voltage determines the load current at which the ADM1270 limits the current during an overcurrent event. This reference voltage is compared to the amplified current sense voltage to determine when the current-limit threshold is reached. Figure 37. Interaction of Foldback (FLB) and ISET Current Limits SETTING THE CURRENT LIMIT (ISET) The maximum current limit is partially determined by selecting a sense resistor to match the current sense voltage limit on the controller for the desired load current. However, as currents become larger, the sense resistor value decreases for a given current sense voltage. Choosing an appropriate current sense resistor can be difficult due to the limited selection of low value resistors. The ADM1270 provides an adjustable current sense voltage limit to handle this issue. The device allows the user to program the required current sense voltage limit from 12.5 mV to 62.5 mV. Rev. A | Page 16 of 21 Data Sheet ADM1270 FOLDBACK The default value is 50 mV and is achieved by connecting the ISET pin directly to the VCAP pin. This circuit configuration configures the device to use an internal 2 V reference, which results in 50 mV at the sense inputs (see Figure 38). RSENSE 4V TO 60V VCC/SENSE+ VCAP Foldback is a method to actively reduce the current limit as the voltage drop across the FET increases. This technique keeps the power dissipation in the FET at a minimum during power-up, overcurrent, or short-circuit events. It also reduces the need to oversize the FET to accommodate worst-case conditions, resulting in board size and cost savings. LDO SENSE– Q1 Assuming that the supply voltage remains constant and within tolerance, the ADM1270 detects the voltage drop across the FET by sensing output voltage through a resistor divider. The device, therefore, relies on the principle that the drain of the FET is at the maximum expected supply voltage, and that the magnitude of the output voltage is relative to that of the VDS of the FET. Using a resistor divider from the output voltage to the FLB pin, the relationship from VOUT, and thus VDS, to VFLB can be derived. – + 40× 2V ISET GATE REF SELECT + CURRENTLIMIT CONTROL 12259-038 FLB CURRENT LIMIT – GND Figure 38. Fixed 50 mV Current Sense Limit To program the sense voltage from 12.5 mV to 62.5 mV, an external resistor divider sets the reference voltage on the ISET pin (see Figure 39). RSENSE 4V TO 60V VCC/SENSE+ VCAP LDO SENSE– + Q1 To ensure that the SOA characteristics of a particular FET are not violated, the minimum current for this clamp varies from design to design. However, the current-limit reference fixes this clamp at 200 mV, which equals 10 mV across the sense resistor. Therefore, the main ISET voltage can be adjusted to adjust the clamp to the required percentage current reduction. For example, if VISET equals 1.6 V, set the clamp at 25% of the maximum current. – 40× 2V GATE REF SELECT + FLB CURRENTLIMIT CONTROL – CURRENT LIMIT TIMER 12259-039 ISET Design the resistor divider to result in a voltage equal to VISET/2 when VOUT falls below the desired level. This voltage must be well below the working tolerance of the supply rail. As VOUT continues to drop, the current-limit reference follows VFLB because it is now the lowest voltage input to the current-limit reference selector block, resulting in a reduction of the current limit and, therefore, the regulated load current. To prevent the current from decreasing to zero, a clamp activates when VFLB reaches 200 mV. The current limit cannot drop below this level. GND Figure 39. Adjustable 12.5 mV to 62.5 mV Current Sense Limit The VCAP pin has a 3.6 V internally generated voltage that can set a voltage at the ISET pin. Assuming that VISET equals the voltage on the ISET pin, select the resistor divider values to set the ISET voltage as follows: VISET = VSENSE × 40 The TIMER pin handles the timing function with an external capacitor, CTIMER. The two TIMER pin comparator thresholds are VTIMERL (0.1 V) and VTIMERH (2.0 V). There are two timing current sources as well: a 20 µA pull-up current and a 1 µA pull-down current. These current and voltage levels, in combination with the user chosen value of CTIMER, determine the fault current-limit time and the on-time of the hot swap retry duty cycle. The TIMER pin capacitor value is determined using the following equation: where VSENSE is the current sense voltage limit. CTIMER = (tON × 20 µA)/VTIMERH The VCAP rail also can be used as the pull-up supply for setting other pins. To guarantee that VCAP meets its accuracy specifications, do not apply a load to the VCAP pin greater than 100 µA. where: tON is the time that the FET is allowed to spend in regulation at the current limit. VTIMERH is the TIMER high threshold. The choice of FET is based on matching this time with the SOA characteristics of the FET. Foldback can also be used to simplify the selection. Rev. A | Page 17 of 21 ADM1270 Data Sheet When the voltage across the sense resistor reaches the circuit breaker trip voltage, VCB, the 20 µA TIMER pull-up current is activated. The ADM1270 begins to regulate the load current at the current limit, initiating a rising voltage ramp on the TIMER pin. If the sense voltage falls below this circuit breaker trip voltage before the TIMER pin reaches VTIMERH, the 20 µA pull-up current is disabled, and the 1 µA pull-down current is enabled. If the voltage on the TIMER pin falls below VTIMERL, the TIMER pin is discharged to GND using a strong pull-down current on the TIMER pin. defined window of operation when the initial timing cycle terminates, the device is ready to start a hot swap operation. However, if the overcurrent condition is continuous and the sense voltage remains above the circuit breaker trip voltage, the 20 µA pull-up current remains active, and the FET remains in regulation. This condition allows the TIMER pin to reach VTIMERH and to initiate the GATE shutdown, and the FAULT pin is pulled low immediately. This fault current-limit off time is determined by the following equation: The circuit breaker trip voltage is not the same as the hot swap sense voltage current limit. There is a small circuit breaker offset, VCBOS, which causes the timer to start shortly before the current reaches the defined current limit. In latch-off mode, the TIMER pin is discharged to GND when it reaches the VTIMERH threshold. The TIMER_OFF pin begins to charge up. While the TIMER_OFF pin is ramping up, the hot swap controller remains off and cannot be turned back on, and the FAULT pin remains low. When the voltage on the TIMER_OFF pin rises above the VTMROFFH threshold, the hot swap controller can be reenabled by toggling the ENABLE pin from high to low and then high again. TIMER_OFF The TIMER_OFF pin handles two timing functions with an external capacitor, CTIMER_OFF. There is one TIMER_OFF pin comparator threshold at VTMROFFH (2.0 V). There are two timing current sources, a 20 µA pull-up current and a 1 µA pull-up current. These current and voltage levels, in combination with the user chosen value of CTIMER_OFF, determine the initial power-on reset time and also set the fault current-limit off time. When VCC is connected to the input supply, the internal supply (VCAP) of the ADM1270 must charge up. VCAP starts up and settles in a very short time. When the UVLO threshold voltage is exceeded at VCAP, the device emerges from reset. During this first brief reset period, the GATE and TIMER pins are both held low. The ADM1270 then proceeds through an initial timing cycle. The TIMER_OFF pin is pulled high with 20 µA. When the TIMER_OFF pin reaches the VTMROFFH threshold (2.0 V), the initial timing cycle is complete. This initial power-on reset duration is determined by the following equation: tINITIAL = VTMROFFH × (CTIMER_OFF/20 µA) For example, a 100 nF capacitor results in a delay of approximately 10 ms. If the UV and OV inputs indicate that VCC is within the At the completion of this initial power-on reset cycle, the TIMER_OFF pin is ready to perform a second function. When the voltage at the TIMER pin exceeds the fault current-limit time threshold voltage of VTIMERH (2.0 V), the 1 µA pull-up current is activated on TIMER_OFF, and CTIMER_OFF begins to charge initiating a voltage ramp on the TIMER_OFF pin. When the TIMER_OFF pin reaches VTMROFFH, the TIMER_OFF fault current-limit off time is complete. tTIMER_OFF = VTMROFFH × (CTIMER_OFF/1 µA) For example, a 100 nF capacitor results in an off time of approximately 200 ms from the time that TIMER exceeds VTIMERH to the time that TIMER_OFF reaches VTMROFFH. HOT SWAP RETRY DUTY CYCLE The ADM1270 turns off the FET after an overcurrent fault and then uses the capacitor on the TIMER_OFF pin to generate a delay before automatically retrying the hot swap operation. To configure the ADM1270 for automatic retry mode, tie the FAULT pin to the ENABLE pin. Note that a pull-up resistor to VCAP is required on the FAULT pin. When an overcurrent fault occurs, the capacitor on the TIMER pin charges with a 20 µA pull-up current. When the TIMER pin reaches VTIMERH (2.0 V), the GATE pin is pulled high, turning off the FET. When the FAULT pin is tied to the ENABLE pin for automatic retry mode, the TIMER_OFF pin begins to charge with a 1 µA current source. When the TIMER_OFF pin reaches VTMROFFH (2.0 V), the ADM1270 automatically restarts the hot swap operation. The automatic retry duty cycle is set by the ratio of 1 µA/20 µA and the ratio of CTIMER/CTIMER_OFF. The retry duty cycle is set by the following equation: Duty_Cycle = (CTIMER × 1 µA)/(CTIMER_OFF × 20 µA) The value of the CTIMER and CTIMER_OFF capacitors determine the on and off time of this cycle, which are calculated as follows: tON = VTIMERH × (CTIMER/20 µA) tOFF = VTMROFFH × (CTIMER_OFF/1 µA) A 100 nF capacitor on the TIMER pin gives an on time of 10 ms. A 100 nF capacitor on the TIMER_OFF pin gives an off time of 200 ms. The device retries continuously in this manner and can be disabled manually by holding the ENABLE pin low, or by disconnecting the FAULT pin. To prevent thermal stress in the FET, a capacitor on the TIMER_OFF pin can be used to extend the retry time to any desired level. Rev. A | Page 18 of 21 Data Sheet ADM1270 RSENSE 4V TO 60V The circuits driving the GATE and RPFG pins are clamped to less than 14 V below the VCC/SENSE+ pin. These clamps ensure that the maximum VGS rating of the external FETs is not exceeded. The reverse protection FET gate pin (RPFG) drives the gate of an external PMOSFET. This PMOSFET, Q2, provides reverse polarity protection to the ADM1270 and the system being powered. If the VCC and GND pins have been reverse connected (that is, where power is actually applied to GND), VCC is negative with respect to the system ground. In this condition, Q2 prevents current from flowing in the reverse direction because the gate of Q2 is held at GND, and Q2 is off. VOUT is not pulled below GND, and the system is protected against a reverse polarity connection. In the typical case where power is applied to VCC, the gate is still pulled down and allows the FET Q2 to turn on and conduct current in the forward direction. Operating Q2 in this way provides a low on-resistance, low voltage drop compared to a diode for reverse polarity protection, giving the system higher efficiency and more headroom for operation. Figure 33 shows the connection of Q2 and RPFG for proper operation. FAST RESPONSE TO SEVERE OVERCURRENT The ADM1270 includes a separate, high bandwidth, current sense amplifier to detect a severe overcurrent that is indicative of a short circuit. The fast response time allows the ADM1270 to handle events of this type that could otherwise cause catastrophic damage if not detected and dealt with very quickly. The fast response circuit ensures that the ADM1270 can detect an overcurrent event of approximately 200% of the normal current limit and control the current within approximately 2 µs. VCC/SENSE+ SENSE– + VCAP – 40× LDO UV + 1V – GATE DRIVE/ LOGIC OV – 1V GATE + GND Figure 40. Undervoltage and Overvoltage Supply Monitoring ENABLE INPUT The ADM1270 provides a dedicated ENABLE digital input pin. The ENABLE pin allows the ADM1270 to remain off by using a hardware signal, even when the voltage on the UV pin is greater than 1.0 V, and the voltage on the OV pin is less than 1.0 V. Although the UV pin can be used to provide a digital enable signal, using the ENABLE pin for this purpose keeps the ability of the UV pin free to monitor undervoltage conditions. In addition to the conditions for the UV and OV pins, the ADM1270 ENABLE input pin must be high for the device to begin a power-up sequence. A similar function can be achieved using the UV pin directly. Alternatively, if the UV divider function is still required, the configuration shown in Figure 41 can be used. VIN SYSTEM CONTROL ADM1270 UNDERVOLTAGE AND OVERVOLTAGE The ADM1270 monitors the supply voltage for UV and OV conditions. The UV and OV pins are connected to the inputs of the voltage comparators and compared to an internal 1 V voltage reference. R1 EN D1 UV R2 12259-041 Figure 40 illustrates the voltage monitoring input connections. An external resistor network divides the supply voltage for monitoring. An undervoltage event is detected when the voltage connected to the UV pin falls below 1 V, and the FET is turned off using the 10 mA pull-up current. Similarly, when an overvoltage event occurs and the voltage on the OV pin exceeds 1 V, the FET is turned off using the 10 mA pull-up current. Q1 12259-040 GATE AND RPFG CLAMPS Figure 41. Using the UV Pin as an Enable Diode D1 prevents the external driver pull-up resistor from affecting the UV threshold. Select Diode D1 using the following criteria: (VF × D1) + (VOL × EN) << 1.0 V (IF = VIN/R1) Ensure that the EN sink current does not exceed the specified VOL value. If the open-drain device has no pull-up, the diode is not required. Rev. A | Page 19 of 21 ADM1270 Data Sheet POWER GOOD When the voltage at the FB_PG pin exceeds the 1 V threshold (indicating that the output voltage has risen), the open-drain pull-down current is disabled, allowing PWRGD to be pulled high. The PWRGD pin is an open-drain output that pulls low when the voltage at the FB_PG pin is lower than the 1 V threshold minus the hysteresis (power bad). Hysteresis on the FB_PG pin is fixed at 30 mV. PWRGD is guaranteed to be in a valid state for VCC ≥ 1.7 V. The power-good (PWRGD) output can be used to indicate whether the output voltage exceeds a user defined threshold and can, therefore, be considered good. The PWRGD output is set by a resistor divider connected to the FB_PG pin (see Figure 42). RSENSE 4V TO 60V VCC/SENSE+ SENSE– + VCAP LDO UV Calculate the power-good threshold using the following equation: Q1 VPWRGD = 1 V × (1 + RPG1/RPG2) – 40× where: RPG1 is the resistance from VOUT to FB_PG. RPG2 is the resistance from FB_PG to GND. + – GATE DRIVE/ LOGIC – 1V + GATE FB_PG GND 12259-042 1V OV Figure 42. Generation of PWRGD Signal Rev. A | Page 20 of 21 Data Sheet ADM1270 OUTLINE DIMENSIONS 3.10 3.00 SQ 2.90 13 0.50 BSC PIN 1 INDICATOR 16 1 12 EXPOSED PAD 1.65 1.50 SQ 1.45 9 TOP VIEW 0.80 0.75 0.70 4 5 8 0.50 0.40 0.30 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF SEATING PLANE 0.20 MIN BOTTOM VIEW FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. 01-26-2012-A PIN 1 INDICATOR 0.30 0.25 0.20 COMPLIANT TO JEDEC STANDARDS MO-220-WEED-6. Figure 43. 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 3 mm × 3 mm Body, Very, Very Thin Quad (CP-16-27) Dimensions shown in millimeters 0.197 (5.00) 0.193 (4.90) 0.189 (4.80) 16 9 1 8 0.010 (0.25) 0.006 (0.15) 0.069 (1.75) 0.053 (1.35) 0.065 (1.65) 0.049 (1.25) 0.010 (0.25) 0.004 (0.10) COPLANARITY 0.004 (0.10) 0.244 (6.20) 0.236 (5.99) 0.228 (5.79) 0.025 (0.64) BSC SEATING PLANE 0.012 (0.30) 0.008 (0.20) 8° 0° 0.020 (0.51) 0.010 (0.25) 0.050 (1.27) 0.016 (0.41) COMPLIANT TO JEDEC STANDARDS MO-137-AB CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 0.041 (1.04) REF 09-12-2014-A 0.158 (4.01) 0.154 (3.91) 0.150 (3.81) Figure 44. 16-Lead Body, Shrink Small Outline Package [QSOP] (RQ-16) Dimensions shown in inches (and millimeters) ORDERING GUIDE Model 1 ADM1270ACPZ-R2 ADM1270ACPZ-R7 ADM1270ARQZ ADM1270ARQZ-R7 ADM1270CP-EVALZ ADM1270RQ-EVALZ 1 Temperature Range −40°C to +125°C −40°C to +125°C −40°C to +125°C −40°C to +125°C Package Description 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 16-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 16-Lead Body, Shrink Small Outline Package [QSOP] 16-Lead Body, Shrink Small Outline Package [QSOP] Evaluation Board for 16-Lead LFCSP_WQ Evaluation Board for 16-Lead QSOP Z = RoHS Compliant Part. ©2014–2016 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D12259-0-4/16(A) Rev. A | Page 21 of 21 Package Option CP-16-27 CP-16-27 RQ-16 RQ-16 Brand Code LNQ LNQ