The GenesysTM family of programmable power supplies sets a new standard for flexible, reliable, AC/DC power systems in OEM, Industrial and Laboratory applications. Features include: • Highest Power Density available 1500W in 1U • Wide Range Input 85 - 265Vac Continuous, single phase, 47/63Hz • Active Power Factor Correction 0.99 • Output up to 600V, Current up to 200A • Built in RS232/RS485 Interface • Software Calibration • Last Setting Memory • High Resolution 16 bits ADCs & DACs • Reliable Encoders for Voltage and Current Adjustment • Constant Voltage/Constant Current auto crossover • Parallel Operation with Active Current Sharing • Independent Remote ON/OFF and Remote Enable/Disable • External Analog Programming and Monitoring • Reliable Modular and SMT Design • 19" Rack Mounted ATE and OEM applications • Five Year Warranty • Optional Isolated Analog Programming and Monitoring • Optional GPIB (SCPI) Interface • LabView® drivers ( LabView® is registered trademark of National Instruments Corporation ) Worldwide Safety Agency Approvals CE Mark for LVD and EMC Regulation Applications Genesys™ power supplies have been designed to meet the demands of a wide variety of applications. Test and Measurement Last setting memory simplifies test design and requires no battery backup. Built in RS232/RS485 gives maximum system flexibility along with 0-5V and 0-10V, selectable analog programming Wide range of available inputs allows testing of many different devices. Semiconductor Burn-in Safe Start may be enabled to restart at zero output to protect load. Wide range input (85-265VAC) with Active Power Factor correction rides through input transients easily. Component Test High power density, zero stacking and single wire parallel operation give maximum system flexibility Laser Diode OVP is directly set on Voltage Meter, assuring accurate protection settings. Current Limit Fold Back assures load is protected from current surges. Heater Supplies Smooth, reliable encoders enhance front panel control. Remote analog programming is user selectable 0-5V or 0-10V. RF Amplifiers and Magnets Robust design assures stable operation under a wide variety of loads. Excellent linearity in voltage and current mode. 1|Genesys™ 750W/1500W-1U Front Panel Description 1. AC On/Off 2. Air Intake allows zero stacking for maximum system flexibility and power density 3. Reliable encoder controls Output Voltage and sets Address. 4. Volt Meter shows Output Voltage and directly displays OVP, UVL and Address settings. 5. Amp Meter also displays baud rate. 6. Reliable encoder controls Output Current and sets baud rate. 7. Function/Status LED's • Alarm • Fine Control • Preview Settings • Foldback Mode • Remote Mode • Output On 8. Pushbuttons allow flexible user configuration Coarse and Fine Voltage and Current Adjustment of Output Preview Settings and Set Voltage while in Current Mode or with Output OFF Set OVP and UVL Limits Set Current Foldback Local/Remote Mode and select Address and Baud Rate Output ON/OFF and Auto Start/Safe Start Mode Rear Panel Description 1. 2. 3. 4. 5. 6. 7. 8. Remote/Local Output Voltage Sense Connections DIP Switches select 0-5V or 0-10V Programming and other functions. DB25 (Female) connector allows (Non-isolated) Analog Program and Monitor as well as other functions. RS485 Out to other Genesys Power Supplies RS232/RS485 IN Remote Serial Programming Output Terminals are rugged bus bars for 6-60V Output, higher output voltage models have terminal block connector. Exit air assures reliable operation when zero stacked Wide-Range Input 85-265VAC continuous, 47/63Hz with Active Power Factor Correction (0.99) AC Input Connector 750W: IEC320, 1500W: Screw terminal Model Shown 9. Position for Optional Isolated Analog Programming or GPIB Digital Interface model shown |2 Genesys ™ 750W/1500W Specifications 1.0 MODEL 1.Rated output voltage(*1) 2.Rated Output Current(*2) 3.Rated Output Power 4.Efficiency at 100/200Vac (*3) 1.0 MODEL 1.Rated output voltage (*1) 2.Rated Output Current (*2) 3.Rated Output Power 750W GEN V 6-200 6 8-180 12.5-120 20-76 8 12.5 20 30-50 30 40-38 40 60-25 60 80-19 100-15 80 100 A W % 200 1200 77/80 180 1440 78/81 76 1520 83/86 50 1500 83/86 38 1520 84/88 25 1500 84/88 19 1520 84/88 GEN V A W 6-100 6 100 600 8-90 8 90 720 12.5-60 20-38 12.5 20 60 38 750 760 30-25 30 25 750 40-19 60-12.5 80-9.5 100-7.5 40 60 80 100 19 12.5 9.5 7.5 760 750 760 750 120 1500 81/84 15 1500 84/88 150-10 150 300-5 300 600-2.6 600 10 1500 84/88 5 1500 83/87 2.6 1560 83/87 150-5 150 5 750 300-2.5 600-1.3 300 600 2.5 1.3 750 780 1.1 CONSTANT VOLTAGE MODE 1.Max.line regulation ( 0.01% of Vo+ 2mV )(*4) 2.Max load regulation ( 0.01% of Vo+2mV )(*5) 3.Ripple and noise p-p 20MHz 4.Ripple r.m.s 5Hz~1MHz 5.Remote sense compensation/line 6.Temp. coefficient 7.Up-prog. response time, 0~Vomax 8.Down-prog response time full-load 9.Down-prog response time no-load 10.Transient response time (*8) mV 2.6 2.8 3.3 4 5 6 8 10 12 17 32 mV 2.6 2.8 3.3 4 5 6 8 10 12 17 32 mV 60 60 60 60 60 60 60 80 100 80 125 mV 8 8 8 8 8 8 8 8 8 10 25 V 1 1 1 1 1.5 2 3 4 5 5 5 PPM/°C 100PPM/°C from rated output voltage,following 30 minutes warm up mS 80mS , N.L/F.L , resistive load 150mS , N.L/F.L , resistive load mS 10 50 80 150 mS 500 600 700 800 900 1000 1100 1200 1500 2000 2500 Less than 1mSec for models up to and including 100V. 2msec for models above 100V 1.2 CONSTANT CURRENT MODE 1.Max.line regulation (0.01% of Io+ 2mA)(*4) 2.Max.load regulation (0.01% of Io+5mA)(*6) 3.Ripple r.m.s 5Hz~1MHz . (*7) 1.Max.line regulation (0.01% of Io+ 2mA)(*4) 2.Max.load regulation (0.01% of Io+5mA)(*6) 3.Ripple r.m.s 5Hz~1MHz .(*7) 4.Temp. coefficient mA 12 5.8 4.5 11 8 3.9 3.25 2.95 15 7.5 mA 14 11 8.8 6.9 6.25 5.95 mA 200 120 76 63 38 180 48 29 2 2 mA 2 2 2 2 2 2 mA 5 5 5 5 5 5 5 5 mA 400 152 125 360 240 95 75 57 PPM/°C 100PPM/°C from rated output voltage,following 30 minutes warm up 1.3 PROTECTIVE FUNCTIONS 1. OCP 2. OCP Foldback 3. OVP type 4. OVP trip point 5. Over Temp. Protection 1.4 ANALOG PROGRAMMING AND MONITORING 1.Vout Voltage Programming 2.Iout Voltage Programming 3.Vout Resistor Programming 4.Iout Resistor Programming 5.On/Off control (rear panel) 6.Output Current monitor 7.Output Voltage monitor 8.Power Supply OK signal 9. CV/CC indicator 10. Enable/Disable 1.5 FRONT PANEL 1.Control functions 2.Display 3.Indications 2.75 5.75 23 2 5 45 2.5 5.5 18 2 5 35 2.25 5.25 13 2 5 25 62 62 300 60 5 4000 2.13 5.13 8 2 5 12 X 1500W X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X 0~105% Constant Current Output shut down when power supply change from CV to CC. User selectable. Inverter shut-down, manual reset by AC input recycle or by OUT button 0.5~7.5V 0.5~10V 1~15V 1~24V 2~36V 2~44V 5~66V 5~88V 5~110V 5~165V 5~330V 5~660V User selectable , latched or non latched X X X X X X X X X X 0~100%, 0~5V or 0~10V, user select. Accuracy and linearity:+/-0.5% of rated Vout. 0~100%, 0~5V or 0~10V, user select. Accuracy and linearity:+/-1% of rated Iout. 0~100%, 0~5/10Kohm full scale,user select.,Accuracy and linearity:+/-1% of rated Vout. 0~100%, 0~5/10Kohm full scale,user select. Accuracy and linearity:+/-1.5% of rated Iout. By electrical. Voltage: 0~0.6V/2~15V,or dry contact ,user selectable logic 0~5V or 0~10V , accuracy:1% , user selectable 0~5V or 0~10V ,accuracy:1% ,user selectable 5V-OK, 0V-Fail 500ohm impedance CV: TTL high (4~5V) source: 10mA, CC: TTL low (0~0.4V):10mA Dry contact. Open:off , Short: on. Max. voltage at Enable/Disable in: 6V X X X X X X X X X X X X X X X X X X X X Vout/ Iout manual adjust by separate encoders (coarse and fine adjustment selectable) OVP/UVL manual adjust by Volt. Adjust encoder AC on/off, Output on/off, Re-start modes (auto, safe), Foldback control (CV to CC), Go to local control Address selection by Voltage (or current) adjust encoder. No of addresses:31 RS232/485 and IEEE488.2 selection by IEEE enable switch and DIP switch Baud rate selection: 1200,2400,4800,9600 and 19,200 bps Voltage 4 digits , accuracy: 0.5%+/-1 count Current 4 digits, accuracy: 0.5%+/-1 count Voltage, Current, Alarm, Fine, Preview, Foldback, Local, Output On X X X X X X X X X X X X X X X X X X 1.6 Interface RS232&RS485 or Optional GPIB Interface V Model Remote Voltage Programming (16 bit) Resolution (0.012% of Vomax) mV Accuracy (0.05%Vomax+0.05% of Vo Actual Output) mV 6 8 12.5 20 30 40 60 80 100 150 300 600 750W X 1500W X 0.72 6.0 0.96 8.0 1.50 12.5 2.40 20 3.60 30 4.80 40 7.2 60 9.6 80 12 100 18 150 36 300 72 600 X X X X Remote Current Programming (16 bit) Resolution (0.012% of Iomax) Accuracy (0.05% of Iomax+0.05% of Io Actual Output) Resolution (0.012% of Iomax) Accuracy (0.05% of Iomax+0.05% of Io Actual Output) 12 10 24 20 10.8 9 21.6 18 7.2 6 14.4 12 4.56 3.8 9.12 7.6 3.0 2.5 6 5 2.28 1.9 4.56 3.8 1.50 1.25 3.0 2.5 1.14 0.95 2.28 1.9 0.90 0.75 1.80 1.50 0.60 0.5 1.20 1 0.30 0.25 0.60 0.5 0.16 0.13 0.32 0.26 X X Readback Voltage Resolution (0.012% of Vomax) mV Accuracy (0.1%Vomax+0.1% of Vo Actual Output) mV 0.72 12 0.96 16 1.50 25 2.40 40 3.60 60 4.80 80 7.2 120 9.6 160 12 200 18 300 36 600 72 1200 X X Readback Current Resolution (0.012% of Iomax ) Accuracy (0.1% of Iomax+0.3% of Io Actual Output) Resolution (0.012% of Iomax ) Accuracy (0.1% of Iomax+0.3% of Io Actual Output) mA mA mA mA 12 400 24 800 10.8 360 21.6 720 7.2 240 14.4 480 4.56 152 9.12 304 3.0 100 6 200 2.28 76 4.56 152 1.50 50 3.0 100 1.14 38 2.28 76 0.9 30 1.80 60 0.60 20 1.20 40 0.30 10 0.60 20 0.16 5.2 0.32 10.4 X X OVP Programming Resolution (0.1% of Vomax) Accuracy (1% of Vomax) mV mV 6 60 8 80 12 125 20 200 29 300 39 400 59 600 78 800 98 1000 146 1500 586 6000 X X mA mA mA mA 293 3000 X X X X X X X X *1: Minimum voltage is guaranteed to maximum 0.2% of Vomax. *3: At maximum output power. *5: From No-load to Full-load, constant input voltage. *2: Minimum current is guaranteed to maximum 0.4% of Iomax. *4: 85~132Vac or 170~265Vac, constant load. *6: For load voltage change, equal to the unit voltage rating, constant input voltage. *7: For 6V models the ripple is measured at 2~6V output voltage and full output current. For other models, the ripple is measured at 10~100% output voltage and full output current. *8: Time for the output voltage to recover within 0.5% of its rated for a load change 10~90% of rated output , Output set-point:10~100%. Accuracy -Values have been calculated at Vomax & Io max 3|Genesys™ 750W/1500W-1U General Specifications Genesys™ 750W/1500W 2.1 INPUT CHARACTERISTICS 1. Input voltage/freq. (*1) 2. Power Factor 3. EN61000-3-2,3 compliance 4. Input current 100/200Vac 5. Inrush current 100/200Vac 6. Hold-up time 85~265Vac continuous, 47~63Hz, single phase 0.99 @100/200Vac, rated output power. Complies with EN61000-3-2 class A and EN61000-3-3 at 20~100% output power. 750W :10.5A / 5A, 1500W :21A / 11A 750W :Less than 25A, 1500W :Less than 50A More than 20mS , 100Vac , at 100% load. 2.2 POWER SUPPLY CONFIGURATION 1. Parallel Operation 2. Series Operation Up to 4 units in master/slave mode with single wire current balance connection Up to 2 units. with external diodes. 600V Max to Chassis ground 2.3 ENVIRONMENTAL CONDITIONS 1. Operating temp 2. Storage temp 3. Operating humidity 4. Storage humidity 5. Vibration 6. Shock 7. Altitude 0~50 °C, 100% load. -20~70°C 30~90% RH (no condensation). 10~95% RH (no condensation). MIL-810E, method 514.4 , test cond. I-3.3.1 . The EUT is fixed to the vibrating surface. Less than 20G , half sine , 11mSec. Unit is unpacked. Operating: 10000ft (3000m) , Non operating: 40000ft (12000m). 2.4 EMC 1.Applicable standards: 2.ESD 3.Fast transients 4.Surge immunity 5.Conducted immunity 6.Radiated immunity 7.Conducted emission 8.Radiated emission 9.Voltage dips 10. Conducted emission 11. Radiated emission EN55024 IEC1000-4-2. Air-disch.-8KV, contact disch.-4KV IEC1000-4-4. 2KV IEC1000-4-5. 1KV line to line, 2KV line to ground IEC1000-4-6, 3V IEC1000-4-3, 3V/m EN55022B,FCC part 15J-B,VCCI-2 EN55022A,FCC part 15-A,VCCI-1 EN61000-4-11 EN55022B, FCC part 15-B, VCCI-2. EN55022A, FCC part 15-A, VCCI-1. 2.5 SAFETY 1.Applicable standards: 2.Withstand voltage 3.Insulation resistance 2.6 MECHANICAL CONSTRUCTION 1. Cooling 2. Dimensions (WxHxD) 3. Weight 4. AC Input connector CE Mark, UL60950,EN60950 listed. Vout<60V:Output is SELV , IEEE/Isolated analog are SELV. 60<Vout<400V: Output is hazardous, IEEE/Isolated analog are SELV. 400<Vout<600V:Output is hazardous, IEEE/Isolated analog are not SELV. Vout<60V models :Input-Outputs (SELV): 3.0KVrms 1min, Input-Ground: 2.0KVrms 1min. 60<Vout<600V models: Input-Haz. Output: 2.5KVrms 1min, Input-SELV: 3KVrms 1min. Hazardous Output.-SELV: 1.9KVrms 1min, Hazardous Output-Ground:1.9KVrms 1min. Input-Ground: 2KVrms 1min. More than 100Mohm at 25°C , 70% RH. 5.Output connectors Forced air flow: from front to rear. No ventilation holes at the top or bottom of the chassis Variable fan speed. W: 422.8mm, H: 43.6mm, D: 432.8mm (excluding connectors, encoders, handles etc..) 750W: 7Kg (15.4 Lbs) 1500W: 8.5Kg (18.7 Lbs) 750W: AC Inlet IEC320. 1500W: screw terminal block, Phoenix P/N: FRONT-4-H-7.62 , with strain relief 6V to 60V models: bus-bars (hole Ø 8.5mm). 80V to 600V models :terminal block ,Phoenix P/N: FRONT-4-H-7.62 2.7 RELIABILITY SPECS 1. Warranty 5 years. *1: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be described as 100-240Vac (50/60Hz). Outline Drawing Genesys™ 750W/1500W Units NOTE 1. PLUG CONNECTORS INCLUDED WITH THE POWER SUPPLY 2. CHASSIS SLIDES MOUNTING HOLES #10-32 MARKED "A" GENERAL DEVICES P/N: CC301-00-S160 OR EQUIVALENT |4 Genesys™ Power Parallel and Series Configurations Parallel operation - Master/ Slave: Active current sharing allows up to 4 units to be connected in an auto parallel configuration for four times the output power. Series operation Up to two units may be connected in series to increase the output voltage or to provide bipolar output. (Max 600V to Chassis Ground) Remote Programming via RS232&RS485 Interface Standard Serial Interface allows chain control of up to 31 power supplies on the same bus with built in RS232&485 Interface Programming Options (Factory installed) Digital Programming via IEEE Interface • IEEE 488.2 Compliant • Program Voltage • Measure Voltage • Over Voltage setting and shutdown • Error and Status Messages P/N: IEEE • SCPI Compliant • Program Current • Measure Current • Current Foldback shutdown Isolated Analog Programming Four Channels to Program and Monitor Voltage and Current Isolation allows operation with floating references and difficult electrical environments. Choose between programming with Voltage or Current. Connection via Removable terminal block P/N: Phoenix MC1,5/8-ST-3.81 P/N: IS510 - Voltage Programming, user selectable 0-5V or 0-10V signal Power supply Voltage and Current Programming accuracy +/-1% Power supply Voltage and Current Monitoring accuracy +/-1.5% P/N: IS420 - Current Programming with 4-20mA signal Power supply Voltage and Current Programming accuracy +/-1% Power supply Voltage and Current Monitoring accuracy +/-1.5% 5|Genesys™ 750W/1500W-1U Power Supply Identification / Accessories How to order GEN 600 - Series Name Output Voltage (0~600V) 2.6 - - Output Current (0~2.6A) Factory Options AC Cable option is 750W only Option: IEEE IS510 IS420 Region: E - Europe J - Japan I - Middle East U - North America Models 750/1500W GEN6-100 GEN6-200 GEN8-90 GEN8-180 GEN12.5-60 GEN12.5-120 GEN20-38 GEN20-76 GEN30-25 GEN30-50 GEN40-19 GEN40-38 Output Power (W) 600 1200 720 1440 750 1500 760 1520 750 1500 760 1520 Output Current (A) 0~100 0~200 0~90 0~180 0~60 0~120 0~38 0~76 0~25 0~50 0~19 0~38 Output Voltage VDC Model 0~6V 0~8V 0~12.5V 0~20V 0~30V 0~40V Output Voltage VDC Model GEN60-12.5 GEN60-25 GEN80-9.5 GEN80-19 GEN100-7.5 GEN100-15 GEN150-5 GEN150-10 GEN300-2.5 GEN300-5 GEN600-1.3 GEN600-2.6 0~60V 0~80V 0~100V 0~150V 0~300V 0~600V Factory option P/N RS232/485 Interface built in Standard GPIB Interface Voltage Programming Isolated analog interface Current Programming Isolated analog interface IEEE IS510 IS420 Output Current (A) 0~12.5 0~25 0~9.5 0~19 0~7.5 0~15 0~5 0~10 0~2.5 0~5 0~1.3 0~2.6 Output Power (W) 750 1500 760 1520 750 1500 750 1500 750 1500 780 1560 AC Cords sets (750W only) Region Output Power AC Cords Wall Plug Power Supply Connector Europe 750W 10A/250 Vac L=2m INT'L 7/VII IEC320-C13 Part Number P/N: GEN/E Japan Middle East North America 750W 750W 750W 13A/125 Vac L=2m 10A/250 Vac L=2m 13A/125 Vac L=2m SI-32 NEMA 5-15P IEC320-C13 IEC320-C13 IEC320-C13 P/N: GEN/J P/N: GEN/I P/N : GEN/U Accessories 1.Communication cable RS232/RS485 Cable is used to connect the power supply to the PC Controller Mode RS485 RS232 RS232 PC Connector Communication Cable Power Supply Connector DB-9F Shield Ground L=2m EIA/TIA-568A (RJ-45) DB-9F Shield Ground L=2m EIA/TIA-568A (RJ-45) DB-25F FShield Ground L=2m EIA/TIA-568A (RJ-45) P/N GEN/485-9 GEN/232-9 GEN/232-25 Serial link cable* Chaining Power Supply to Power Supply up to 31 GEN units Mode Power Supply Connector Communication Cable P/N RS485 EIA/TIA-568A (RJ-45) Shield Ground L=50cm GEN/RJ45 * Included with the power supply |6