CRA12E, CRA12S www.vishay.com Vishay Thick Film Chip Resistor Array FETAURES • Convex terminal array available with either scalloped corners (E version) or square corners (S version) • Wide ohmic range: 10R to 1M0 • 8 or 10 terminal package with isolated resistors • Pure tin solder contacts on Ni barrier layer, provides compatibility with lead (Pb)-free and lead containing soldering processes • Material categorization: For definitions of compliance please see www.vishay.com/doc?99912 STANDARD ELECTRICAL SPECIFICATIONS MODEL CIRCUIT POWER RATING P70 °C W 01; 02; 20 CRA12E CRA12S LIMITING ELEMENT VOLTAGE MAX. V 0.100 50 0.125 03 TOLERANCE ±% RESISTANCE RANGE SERIES 100 1 10 to 1M E24; E96 200 2; 5 10 to 1M E24 TEMPERATURE COEFFICIENT ± ppm/K Zero-Ohm-Resistor: Rmax. = 50 m, Imax. = 1.5 A TECHNICAL SEPCIFICATIONS UNIT CRA12E AND CRA12S CIRCUIT 01; 02; 20 CRA12E AND CRA12S CIRCUIT 03 Rated dissipation at P70 (1) W per element 0.1 0.125 Limiting element voltage Umax. AC/DC V PARAMETER 50 Insulation voltage Uins (1 min) V 100 Insulation resistance > 109 Category temperature range °C - 55 to + 155 Note (1) Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material. PART NUMBER AND PRODUCT DESCRIPTION Part Number: CRA12E08347K0JTR (2) C R MODEL CRA12 A 1 TERMINAL STYLE S E Product Description: 2 E 0 8 3 4 7 K 0 J T R PIN CIRCUIT VALUE TOLERANCE PACKAGING SPECIAL 08 10 1 = 01 2 = 02 3 = 03 8 = 20 R = Decimal K = Thousand M = Million 0000 = 0 Jumper F=±1% G=±2% J=±5% Z = 0 Jumper TR Up to 2 digits TL CRA12E 08 03 47K 5 % RB8 e3 CRA12E 08 03 47K 5% RB8 e3 MODEL PIN CIRCUIT RESISTANCE VALUE TOLERANCE PACKAGING LEAD (Pb)-FREE CRA12E CRA12S 08 10 01 02 03 20 10R = 10 47K = 47 k 1M = 1M 0R0 = Jumper ±1% ±2% ±5% RB8 RD7 e3 = Pure tin termination finish Note (2) Preferred way for ordering products is by use of the PART NUMBER. Revision: 24-Jun-13 Document Number: 31003 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRA12E, CRA12S www.vishay.com Vishay AVAILABLE TYPES AND RANGES MODEL TERMINAL COUNT CIRCUIT CRA12S 10 01 02 03 20 TEMPERATURE COEFFICIENT TOLERANCE ± 100 ppm/K ± 200 ppm/K ± 1 %; ± 2 %; ± 5 % 01 02 03 20 08 CRA12E 10 PACKAGING MODEL CRA12E 08 CRA12E 10 CRA12S 10 TAPE WIDTH DIAMETER 180 mm/7" 330 mm/13" 12 mm PITCH 8 mm PIECES/REEL 2000 5000 BLISTER TAPE ACC. IEC 60286-3, TYPE II PART NUMBER PRODUCT DESCRIPTION TR TL RB8 RD7 CIRCUIT 01 Circuit Pin 1 8 pin 02 Circuit 10 pin Pin 1 03 Circuit 8 pin Revision: 24-Jun-13 10 pin 20 Circuit 10 pin Pin 1 Document Number: 31003 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRA12E, CRA12S www.vishay.com Vishay Fraction of Rated Dissipation in % DERATING 120 100 80 60 40 20 0 - 55 - 25 0 25 50 75 70 100 125 155 175 Ambient Temperature in °C DIMENSIONS S-Version E-Version B 3 0 1 P A* A* B* L B* A W 3 0 1 P T B T L A W PIN 1 PIN 1 W W p p e d a a a c b PIN MODEL NO # CRA12E b e SOLDER PAD DIMENSIONS in millimeters DIMENSIONS in millimeters L A A* a c B B* P T c w d p a b e WAVE 2.2 4.3 0.57 1.27 0.71 1.05 1.09 REFLOW 2.2 3.9 0.57 1.27 0.71 0.86 1.09 W 8 5.08 0.79 - 0.51 0.38 1.27 0.55 3.05 CRA12E 10 6.40 0.79 - 0.51 0.38 1.27 0.55 3.05 CRA12S 10 6.40 0.79 0.89 0.51 0.38 1.27 0.55 3.05 TOL. ± 0.15 ± 0.15 ± 0.15 ± 0.25 ± 0.2 ± 0.1 ± 0.15 ± 0.15 Revision: 24-Jun-13 Document Number: 31003 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 CRA12E, CRA12S www.vishay.com Vishay TEST PROCEDURES AND REQUIREMENTS EN 60115-1 CLAUSE IEC 60068-2 TEST METHOD TEST 4.5 4.7 - Resistance Voltage proof 4.13 - Short time overload 4.17.2 58 (Td) Solderability 4.8.4.2 4.32 21 (UU3) Temperature coefficient Shear (adhesion) 4.33 21 (UU1) Substrate bending 4.19 14 (Na) Rapid change of temperature 4.23 4.23.2 4.23.3 4.23.4 4.23.5 4.23.6 2 (Ba) 30 (Db) 1 (Aa) 13 (M) 30 (Db) Dry heat Damp heat, cyclic Cold Low air pressure Damp heat, cyclic 4.23.7 - DC load PROCEDURE Stability for product type: 10 to 1 M CRA12E/CRA12S ±1% ± 2 %, ± 5 % No flashover or breakdown U = 1.4 x Uins; 60 s U = 2.5 x P 70 x R 2 x Umax.; ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) Duration according to style Solder bath method; Sn60Pb40; Good tinning ( 95 % covered) non-activated flux; no visible damage (235 ± 5) °C; (2 ± 0.2) s Solder bath method; Sn96.5Ag3Cu0.5; Good tinning ( 95 % covered) non-activated flux; no visible damage (245 ± 5) °C; (3 ± 0.3) s (20/- 55/20) °C and (20/125/20) °C ± 100 ppm/K ± 200 ppm/K 45 N No visible damage No visible damage, Depth 2 mm; 3 times no open circuit in bent position ± (0.25 % R + 0.05 ) 30 min. at - 55 °C; 30 min at 125 °C 5 cycles ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) 1000 cycles ± (1 % R + 0.05 ) ± (1 % R + 0.05 ) 125 °C; 16 h 55 °C; 90 % RH; 24 h; 1 cycle - 55 °C; 2 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) 1 kPa; (25 ± 10) °C; 1 h 55 °C; 90 % RH; 24 h; 5 cycle U = U = 4.25.1 - Endurance at 70 °C 4.18.2 58 (Td) Resistance to soldering heat 4.35 4.24 4.25.3 Flammability, needle flame test 78 (Cab) Damp heat, steady state Endurance at upper category temperature REQUIREMENTS PERMISSIBLE CHANGE (R)(1) STABILITY CLASS 1 STABILITY CLASS 2 OR BETTER OR BETTER P 70 x R P 70 x R U max. 1.5 h on; 0.5 h off; 70 °C; 1000 h 70 °C; 8000 h Solder bath method; (260 ± 5) °C; (10 ± 1) s IEC 60695-11-5; 10 s (40 ± 2) °C; (93 ± 3) % RH; 56 days 155 °C; 1000 h ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) ± (2 % R + 0.1 ) ± (4 % R + 0.1 ) ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) No burning after 30 s ± (1 % R + 0.05 ) ± (1 % R + 0.05 ) ± (2 % R + 0.1 ) IEC 61340-3-1; 3 positive and 3 negative discharges; ± (1 % R + 0.05 ) ESD voltage: 500 V Component solvent resistance Isopropyl alcohol; 50 °C; method 2 No visible damage Isopropyl alcohol; 50 °C; method 1; Marking legible, Solvent resistance of marking toothbrush no visible damage Vibration, endurance f = 10 Hz to 2000 Hz; x, y, z 1.5 mm; ± (0.25 % R + 0.05 ) ± (0.5 % R + 0.05 ) by sweeping A 200 m/s2; 10 sweeps per axis Electrostatic discharge (human body model) 4.40 - 4.29 45 (XA) 4.30 45 (XA) 4.22 6 (Fc) 4.37 - Periodic electric overload 4.27 - Single pulse high voltage overload, 10 μs/700 μs U = 15 x P 70 x R 2 x U max. ± (1 % R + 0.05 ) P 70 x R 2 x U max. ± (1 % R + 0.05 ) 0.1 s on; 2.5 s off; 1000 cycles Û = 10 x 10 pulses Note (1) Figures are given for a single element. All tests are carried out in accordance with the following specifications: • EN 60115-1, generic specification • EN 140400, sectional specification • EN 140401-802, detail specification • IEC 60068-2 environmental test procedures Packaging of components is done in paper or blister tapes according to IEC 60286-3 Revision: 24-Jun-13 Document Number: 31003 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000