CDCVF111 1:9 DIFFERENTIAL LVPECL CLOCK DRIVER SCAS670B – SEPTEMBER 2001 – REVISED JUNE 2002 D Low-Output Skew for Clock-Distribution FN PACKAGE (TOP VIEW) Applications D D (LVPECL) Compatible Inputs and Outputs Distributes Differential Clock Inputs to Nine Differential Clock Outputs Output Reference Voltage (VREF ) Allows Distribution From a Single-Ended Clock Input Packaged In a 28-Pin Plastic Chip Carrier description 5 VCC Y7 Y6 Y6 4 3 2 1 28 27 26 25 6 24 7 23 8 22 9 21 10 20 11 19 12 13 14 15 16 17 18 Y5 Y5 Y4 The differential LVPECL clock-driver circuit distributes one pair of differential LVPECL clock inputs (CLKIN, CLKIN) to nine pairs of differential clock (Y, Y) outputs with minimum skew for clock distribution. It is specifically designed for driving 50-Ω transmission lines. Y8 Y8 Y7 Y0 Y0 Y1 VCC Y1 Y2 Y2 VCC Y4 Y3 Y3 D NC VREF CLKIN VCC CLKIN NC GND D Differential Low-Voltage Pseudo-ECL NC – No internal connection The VREF output can be strapped to the CLKIN input for a single-ended CLKIN input. The CDCVF111 is characterized for operation from –40°C to 85°C. FUNCTION TABLE INPUTS OUTPUTS CLKIN CLKIN Yn Yn X X L H H L H L H L H L L VREF VREF L H H L L H L H L H H VREF VREF Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright 2002, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 CDCVF111 1:9 DIFFERENTIAL LVPECL CLOCK DRIVER SCAS670B – SEPTEMBER 2001 – REVISED JUNE 2002 logic diagram (positive logic) 25 24 23 21 20 19 18 17 CLKIN CLKIN 28 16 2 14 13 12 11 10 9 7 6 5 VREF 3 Y0 Y0 Y1 Y1 Y2 Y2 Y3 Y3 Y4 Y4 Y5 Y5 Y6 Y6 Y7 Y7 Y8 Y8 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to 4.6 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V Output voltage range, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 18 mA Output clamp current, IOK (VO < 0 or VO > VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 18 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 50 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . "80 mA Maximum power dissipation at TA = 55°C (in still air) (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 525 mW Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output clamp-current ratings are observed. 2. The maximum package power dissipation is calculated using a junction temperature of 150_C and a board trace length of 750 mils. For more information, refer to the Package Thermal Considerations application note in the ABT Advanced BiCMOS Technology Data Book, literature number SCBD002. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 CDCVF111 1:9 DIFFERENTIAL LVPECL CLOCK DRIVER SCAS670B – SEPTEMBER 2001 – REVISED JUNE 2002 recommended operating conditions VCC Supply voltage VIH High level input voltage High-level VIL Low level input voltage Low-level TA Operating free-air temperature fclock Input frequency MIN MAX UNIT 3 3.6 V VCC = 3 V to 3.6 V VCC = 3.3 V VCC–1.165 2.135 VCC–0.88 2.42 V VCC = 3 V to 3.6 V VCC = 3.3 V VCC–1.81 1.49 VCC–1.475 1.825 V –40 85 °C 650 MHz V V electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VREF VOH TEST CONDITIONS MIN MAX UNIT VCC –1.38 1.92 VCC –1.26 2.04 V VCC = 3 V to 3.6 V, TA = 0°C to 85°C, f(max) = 650 MHz VCC –1.12 VCC – 0.83 VCC = 3 V to 3.6 V, TA = –40°C to 85°C, f(max) = 650 MHz VCC –1.15 VCC – 0.83 2.275 2.42 VCC = 3 V to 3.6 V VCC = 3.3 V IREF = 100 µA A VCC = 3.3 V VCC = 3 V to 3.6 V TA = 0°C to 85°C, f(max) = 650 MHz VOL II ICC (Internal) V VCC = 3 V to 3.6 V, TA = –40°C to 85°C, f(max) = 650 MHz VCC = 3.3 V VI = 2.4 V, IO = 0, VCC –1.86 VCC –1.49 VCC –1.86 VCC –1.52 1.49 1.68 VCC = 3 .6 V VCC = 3 .6 V 150 µA 100 mA switching characteristics over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (see Figure 1 and Figure 2) PARAMETER FROM (INPUT) TO (OUTPUT) MIN MAX UNIT tPLH tPHL CLKIN CLKIN CLKIN, Y Y Y, 450 600 ps tsk(o) Y, Y 50 ps tsk(pr) Y, Y 150 ps tr tf Y Y Y, 600 ps POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 200 3 CDCVF111 1:9 DIFFERENTIAL LVPECL CLOCK DRIVER SCAS670B – SEPTEMBER 2001 – REVISED JUNE 2002 ESD information ESD MODELS LIMIT Human Body Model (HBM) 2.0 kV Machine Model (MM) 200 V Charge Device Model (CDM) 2.0 kV thermal information THERMAL AIR FLOW (CFM) PIN PLCC CDCVF111 28 28-PIN 0 150 250 500 UNIT RθJA High K 48 44 42 39 °C/W RθJA Low K 70 58 52 46 °C/W RθJC High K 22 °C/W RθJC Low K 28 °C/W PARAMETER MEASUREMENT INFORMATION VCC = 2 V Oscilloscope LVPECL Driver ZO = 50 Ω Yn 50 Ω Yn ZO = 50 Ω 50 Ω VEE = –1.3 V LOAD CIRCUIT (See Note B) Y, Y Outputs 80% 20% tr VOH 80% 20% VOL tf VOLTAGE WAVEFORMS RISE AND FALL TIMES CLKIN VCC – 0.9 V VCC – 1.7 V CLKIN tPLH tPHL VOH Y Outputs VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES NOTES: A. All input pulses are supplied by generators having the following characteristics: PRR ≤ 45 MHz, ZO = 50 Ω, tr ≤ 1 ns, tf ≤ 1 ns. B. For additonal signal interface, see the Interfacing Between LVPECL, LVDS, and CML application note, Literature Number SCAA056. Figure 1. Load Circuit and Voltage Waveforms 4 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 CDCVF111 1:9 DIFFERENTIAL LVPECL CLOCK DRIVER SCAS670B – SEPTEMBER 2001 – REVISED JUNE 2002 CLKIN CLKIN Y0 Y0 tPLH1 tPHL1 tPLH2 tPHL2 tPLH3 tPHL3 tPLH4 tPHL4 tPLH5 tPHL5 tPLH6 tPHL6 tPLH7 tPHL7 tPLH8 tPHL8 tPLH9 tPHL9 Y1 Y1 Y2 Y2 Y3 Y3 Y4 Y4 Y5 Y5 Y6 Y6 Y7 Y7 Y8 Y8 NOTES: A. Output skew, tsk(o), is calculated as the greater of: – The difference between the fastest and slowest tPLHn (n = 1, 2, . . . 9) – The difference between the fastest and slowest tPHLn (n = 1, 2, . . . 9) B. Process skew, tsk(pr), is calculated as the greater of: – The difference between the fastest and slowest tPLHn (n = 1, 2, . . . 9) – The difference between the fastest and slowest tPHLn (n = 1, 2, . . . 9) across multiple devices C. For additional information on skew and propagation delay parameters, see the Defining Skew, Propagation Delay, Phase-Offset (Phase Error) application note, literature number SCAA055. Figure 2. Waveforms for Calculation of tsk(o), tsk(pr) POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 24-Jan-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Qty Drawing Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (°C) Top-Side Markings (3) (4) CDCVF111FN ACTIVE PLCC FN 28 37 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 CDCVF111 CDCVF111FNG4 ACTIVE PLCC FN 28 37 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 CDCVF111 CDCVF111FNR ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 CDCVF111 CDCVF111FNRG4 ACTIVE PLCC FN 28 750 Green (RoHS & no Sb/Br) CU NIPDAU Level-1-260C-UNLIM -40 to 85 CDCVF111 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) Only one of markings shown within the brackets will appear on the physical device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 24-Jan-2013 Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 4-Mar-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device CDCVF111FNR Package Package Pins Type Drawing PLCC FN 28 SPQ 750 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 330.0 24.4 Pack Materials-Page 1 12.95 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 12.95 5.0 16.0 24.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 4-Mar-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) CDCVF111FNR PLCC FN 28 750 346.0 346.0 41.0 Pack Materials-Page 2 MECHANICAL DATA MPLC004A – OCTOBER 1994 FN (S-PQCC-J**) PLASTIC J-LEADED CHIP CARRIER 20 PIN SHOWN Seating Plane 0.004 (0,10) 0.180 (4,57) MAX 0.120 (3,05) 0.090 (2,29) D D1 0.020 (0,51) MIN 3 1 19 0.032 (0,81) 0.026 (0,66) 4 E 18 D2 / E2 E1 D2 / E2 8 14 0.021 (0,53) 0.013 (0,33) 0.007 (0,18) M 0.050 (1,27) 9 13 0.008 (0,20) NOM D/E D2 / E2 D1 / E1 NO. OF PINS ** MIN MAX MIN MAX MIN MAX 20 0.385 (9,78) 0.395 (10,03) 0.350 (8,89) 0.356 (9,04) 0.141 (3,58) 0.169 (4,29) 28 0.485 (12,32) 0.495 (12,57) 0.450 (11,43) 0.456 (11,58) 0.191 (4,85) 0.219 (5,56) 44 0.685 (17,40) 0.695 (17,65) 0.650 (16,51) 0.656 (16,66) 0.291 (7,39) 0.319 (8,10) 52 0.785 (19,94) 0.795 (20,19) 0.750 (19,05) 0.756 (19,20) 0.341 (8,66) 0.369 (9,37) 68 0.985 (25,02) 0.995 (25,27) 0.950 (24,13) 0.958 (24,33) 0.441 (11,20) 0.469 (11,91) 84 1.185 (30,10) 1.195 (30,35) 1.150 (29,21) 1.158 (29,41) 0.541 (13,74) 0.569 (14,45) 4040005 / B 03/95 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-018 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2013, Texas Instruments Incorporated