Rohm MNR35 Compact 8-element chip resistor network Datasheet

MNR35
Resistors
Compact 8-element Chip Resistor Networks
MNR35 (1206×5 size)
zFeatures
1) Common terminals yield area 40% smaller than that of the MNR38.
2) 8-element construction makes the MNR35 ideal for bus line pull-up / pull-down.
3) Convex electrodes
Easy to check the fillet after soldering is finished.
4) Compatible with a wide range of mounting equipment.
Squared corners make it excellent for mounting using image recognition devices.
5) ROHM resistors have approved ISO9001- / ISO/TS 16949- certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with
the product before using or ordering it.
zRatings
Item
Rated power
Conditions
Specifications
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
0.063W (1 / 16W)
at 70°C
POWER LOAD (%)
100
80
60
40
20
0
−55
0
70
100
125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the limiting element voltage, the voltage rating
is equal to the maximum operating voltage.
E: Rated voltage (V)
E=
P×R
P: Rated power (W)
Limiting element voltage
R: Nominal resistance (Ω)
Nominal resistance
50V
See Table 1.
−55°C to +125°C
Operating temperature
Table 1
Resistance tolerance
J (±5%)
Resistance range
(Ω)
56≤R≤100k
(E12)
Resistance temperature coefficient
(ppm / °C)
±200
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
Rev.D
1/3
MNR35
Resistors
zCharacteristics
Guaranteed value
Resistor type
Item
Test conditions (JIS C 5201-1)
J : ±5%
Resistance
Variation of resistance
with temperature
JIS C 5201-1 4.5
JIS C 5201-1 4.8
Measurement : −55 / +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
Maximum Overload Voltage : 100V
± (2.0%+0.1Ω)
Overload
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
Solderability
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
± (1.0%+0.1Ω)
No remarkable abnormality on the appearance.
Resistance to
soldering heat
Rapid change of
temperature
± (1.0%+0.1Ω)
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
± (3.0%+0.1Ω)
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
± (3.0%+0.1Ω)
JIS C 5201-1 4.25.1
Rated voltage (current), 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
± (3.0%+0.1Ω)
JIS C 5201-1 4.25.3
125°C
Test time : 1,000h to 1,048h
± (1.0%+0.1Ω)
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
Damp heat, steady state
Endurance at 70°C
Endurance
Resistance to solvent
± (1.0%+0.05Ω)
Without mechanical damage such as breaks.
Bend strength of
the end face plating
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
JIS C 5201-1 4.33
zDimensions (Unit : mm)
Cross section A-A'
6.4±0.4
∗1.27
2
1
6
1
1
1
B
Material
Max.0.5
R 1 0 3
0.5±0.3
A'
3.1±0.2
5
A
Cross section B-B'
6 1
5
0.55±0.1
B'
0.5±0.2
1.0±0.2
2
3
4
1
Resistive element
(Oxide metal thick film)
2
Silver thick film electrode
3
Nickel electrode
4
Sn electrode
5
Alumina substrate
6
Overcoating (Glass)
0.8±0.2
∗ Pitch of the upper electrode.
Rev.D
2/3
MNR35
Resistors
zEquivalent circuit
R1
R8
R7
R6
R2
R3
R4
R5
R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8
zPackaging
Reel
Taping
P2
E
B0
02
04
06
08
06
D
04
B
02
A
08
W
F
φD
0
P0
A0
K
P1
C
(Unit : mm)
Label
W
F
E
A0
B0
12.0±0.3
5.5±0.05
1.75±0.1
3.4±0.1
6.6±0.1
D0
P0
P1
P2
K
+0.1
φ1.5
0
4.0±0.1
4.0±0.1
2.0±0.05
1.0±0.15
EIAJ ET-7200B compliant
(Unit : mm)
A
φ180
B
0
−1.5
φ60
C
+1
0
13 +1.0
−0
D
φ13±0.2
zPart No. Explanation
M N R 3 5
Part No.
J 5 R
J
Resistance tolerance
Nominal resistance
J
±5%
J is also used
for jumper
Resistance code,3 digits,
000 denotes Jumper type.
Packaging Specifications Code
Part No.
Code
MNR35
J5R
Resistance tolerance
J(±5%)
Packaging specifications
Reel
Basic ordering unit (pcs)
Embossed tape (4mm Pitch)
φ180mm (7in.)
4,000
Reel (φ180) : JEITA ET-7200B
: Standard product
Rev.D
3/3
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level
of reliability and the malfunction of which would directly endanger human life (such as medical
instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers
and other safety devices), please be sure to consult with our sales representative in advance.
It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance
of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow
for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in
order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM
cannot be held responsible for any damages arising from the use of the products under conditions out of the
range of the specifications or due to non-compliance with the NOTES specified in this catalog.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2008 ROHM CO.,LTD.
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster@ rohm.co. jp
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix1-Rev2.0
Similar pages