Power DI-33 Wide range dvd supply: <50 mw no-load consumption Datasheet

®
Design Idea DI-33
®
TinySwitch-II Wide Range DVD
Supply: <50 mW No-load Consumption
Application
Device
Power Output
Input Voltage
Output Voltage
Topology
DVD Player
TNY268P
11 W cont. 17 W pk.
85-265 VAC
+3.3 V, +5.0 V, +12.0 V, -12 V
Flyback
Design Highlights
•
•
•
•
No-load input power <50 mW
700 mW of output power with 1 W input
Built-in frequency jitter allows low cost π filter
132 kHz operation minimizes transformer size and turns,
providing good cross-regulation
• High efficiency – >77% minimum
• Meets CISPR22B/EN55022B and FCC B with >10 dB margin
•
•
•
•
Key Design Points
• An optional low voltage bias circuit, D9 and C10, powers U1
via R6, reducing light and zero load power consumption.
This provides bias current that would otherwise be provided
from the DRAIN by the internal high voltage current source.
The current source is disabled when the BP pin is fed
externally, an internal clamp limiting the voltage to
6.3 V. The bias supply is designed to produce 7.5 V at
no-load. Resistor R6 is chosen to provide
approximately 500 µA into the BP pin, the maximum
consumption at no-load.
• Good cross-regulation on 5 V and 3.3 V outputs is
achieved by minimizing secondary leakage through
•
the use of foil windings and dual sense feedback via R15
and R16.
To minimize potential noise coupling to the SOURCE pin
during common mode surges, the Y1 capacitor C8 is
connected between secondary return and the HV DC rail.
Resistors R5 and R7 damp ringing to improve EMI.
Optional soft-finish capacitor C7 eliminates output startup
overshoot.
Optional under-voltage resistor R1 provides clean startup
and prevents output glitches on power down.
R1 = (VUV-2.5 V)/50 µA.
Small loop areas in the secondary layout around D10,
C12, D9, C11, D7, C15, D8 and C9 together with postfilters L2/C20, L3/C17 and L4/C18 provide low output
ripple, below 50 mV p-p.
12 V, 0.4 A
8
D7
UF4003
D9
1N5822
L2
3.3 uH
C15
470 µF
25 V
5 V, 1.6 A
13
L3
3.3 uH
D10
1N5822
C8
1 nF
Y1
C17
470 µF
10 V
C11
1800 µF
25 V
3.3 V, 0.7 A
9
L4
3.3 uH
C12
1000 µF
10 V
R7
100 Ω
D1 & D2
1N4007
VR1
P6KE180
C18
470 µF
10 V
RTN
11
C2
0.01 µF
1 kV
1
C9
220 µF
25 V
C6
220 µF
25 V
D8 UF4003
F1
L
85-265
VAC
C20
150 µF
25 V
C3
0.047 µF
X2
C1 & C4
33 µF
400 V
R5
47 Ω
R1
2 MΩ
(Optional)
D5
1N4007
N
D
D3 & D4
1N4007
4
TinySwitch-II
U2
EN
U1 S
TNY268
C5
0.1 µF
50 V
U2
PC817
C7
10 µF
50 V
R9
200 Ω
R16
6.34 kΩ
1%
R10
3.3 kΩ
5,7
BP
L1
1.4 mH
0.5 A
-12 V, 0.1 A
14
R6
R12
D6 1N4148 3.3 kΩ 1 Ω
1/2 W
6
C10
R8
10 µF
1 kΩ
50 V
C14
0.1 µF
U3
TL431
R15
20 kΩ
1%
R13
10 kΩ
1%
PI-3205-091302
Figure 1. TinySwitch-II DVD Player Schematic.
DI-33
www.powerint.com
September 2002
DI-33
PI-3301-091602
1200
115 VAC
230 VAC
1000
TRANSFORMER PARAMETERS
Core Material
Himag MZ4 EEL25.4, or equivalent,
2
Gap for AL of 344 nH/T
Bobbin
EEL25 Vertical 14 Pins
Winding Details
Shield: 32T, 2 x 32 AWG
Primary: 64T, 2 x 32 AWG
Bias: 6T, 4 x 32 AWG
Shield 2: 4T, 4 x 32 AWG
+12 V: 4T, 4 x 32 AWG
+5 V: 1T, 14 mm Cu Foil
+3.3 V: 2T, 14 mm Cu Foil
-12 V: 7T, 4 x 32 AWG
Winding Order
(Pin Numbers)
3 mm margin tape on both
sides of bobbin.
Shield (NC-5), tape,
Primary (1-4), tape,
Bias (7-6), tape,
Shield (NC-7), tape,
12 V (13-8), 3.3 V (11-9),
5 V (9-13), tape,
-12 V (14-11), tape
(NC - no connect)
Inductance
1420 µH ±25%
Primary Resonant
Frequency
(Pins 1-4, all other open)
500 kHz (minimum)
PIN (mW)
800
600
400
200
0
0
100 200 300 400 500 600 700 800
POUT (mW)
Figure 2. PIN vs. POUT Curve.
PI-3302-091302
80
70
QP
60
AV
50
dBµV
40
Quasi Peak
30
20
Table 1. Transformer Construction Information.
10
Average
0
-10
-20
0.15
1.0
10.0
-100.0
MHz
Figure 3. Conducted EMI with Artificial Hand Connected to Output Return.
For the latest updates, visit our Web site: www.powerint.com
Power Integrations reserves the right to make changes to its products at any time to improve reliability or manufacturability.
Power Integrations does not assume any liability arising from the use of any device or circuit described herein, nor does it convey any
license under its patent rights or the rights of others. The products and applications illustrated herein may be covered by one or more U.S.
and foreign patents or potentially by pending U.S. and foreign patent applications assigned to Power Integrations. A complete list of Power
Integrations’ patents may be found at www.powerint.com.
The PI Logo, TOPSwitch, TinySwitch and EcoSmart are registered trademarks of Power Integrations, Inc.
PI Expert is a trademark of Power Integrations, Inc. ©Copyright 2002, Power Integrations, Inc.
WORLD HEADQUARTERS
AMERICAS
Power Integrations, Inc.
San Jose, CA 95138 USA
Customer Service:
Phone:
+1 408-414-9665
Fax:
+1 408-414-9765
e-mail: [email protected]
CHINA
Power Integrations International
Holdings, Inc.
China
Phone:
+86-755-8367-5143
Fax:
+86-755-8377-9610
e-mail: [email protected]
A
9/02
EUROPE & AFRICA
Power Integrations (Europe) Ltd.
United Kingdom
Phone:
+44-1344-462-300
Fax:
+44-1344-311-732
e-mail: [email protected]
SINGAPORE
Power Integrations, Singapore
Republic of Singapore 308900
Phone:
+65-6358-2160
Fax:
+65-6358-2015
e-mail: [email protected]
KOREA
Power Integrations
International Holdings, Inc.
Seoul, Korea
Phone:
+82-2-782-2840
Fax:
+82-2-782-4427
e-mail: [email protected]
JAPAN
Power Integrations, K.K.
Keihin-Tatemono 1st Bldg.
Japan
Phone:
+81-45-471-1021
Fax:
+81-45-471-3717
e-mail: [email protected]
APPLICATIONS HOTLINE
World Wide +1-408-414-9660
www.powerint.com
TAIWAN
Power Integrations
International Holdings, Inc.
Taipei, Taiwan
Phone:
+886-2-2727-1221
Fax:
+886-2-2727-1223
e-mail: [email protected]
INDIA (Technical Support)
Innovatech
Bangalore, India
Phone:
+91-80-226-6023
Fax:
+91-80-228-9727
e-mail: [email protected]
APPLICATIONS FAX
World Wide +1-408-414-9760
Similar pages