TI1 LM4132 Lm4132, lm4132-q1 sot-23 precision low dropout voltage reference Datasheet

Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
Reference
Design
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
LM4132, LM4132-Q1 SOT-23 Precision Low Dropout Voltage Reference
1 Features
3 Description
•
•
The LM4132 family of precision voltage references
performs comparable to the best laser-trimmed
bipolar references, but in cost-effective CMOS
technology. The key to this breakthrough is the use of
EEPROM registers for correction of curvature,
temperature coefficient (tempco), and accuracy on a
CMOS bandgap architecture allowing package-level
programming to overcome assembly shift. The shifts
in voltage accuracy and tempco during assembly of
die into plastic packages limit the accuracy of
references trimmed with laser techniques.
1
•
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
AEC-Q100 Qualified With the Following Results:
– Device Temperature Grade 1: –40ºC to 125ºC
Ambient Operating Temperature Range
– Device HBM ESD Classification Level 2
Output Initial Voltage Accuracy 0.05%
Low Temperature Coefficient 10 ppm/°C
Low Supply Current, 60 µA
Enable Pin Allowing a 3-µA Shutdown Mode
20-mA Output Current
Voltage Options 1.8 V, 2.048 V, 2.5 V, 3 V,
3.3 V, 4.096 V
Custom Voltage Options Available
(1.8 V to 4.096 V)
VIN Range of VREF + 400 mV to 5.5 V at 10 mA
Stable With Low ESR Ceramic Capacitors
Unlike other LDO references, the LM4132 can deliver
up to 20 mA and does not require an output capacitor
or buffer amplifier. These advantages along with the
SOT-23 packaging are important for space-critical
applications.
Series references provide lower power consumption
than shunt references, because they do not have to
idle the maximum possible load current under no-load
conditions. This advantage, the low quiescent current
(60 µA), and the low dropout voltage (400 mV) make
the LM4132 ideal for battery-powered solutions.
2 Applications
•
•
•
•
•
•
•
•
•
•
•
Instrumentation and Process Control
Test Equipment
Data Acquisition Systems
Base Stations
Servo Systems
Portable, Battery Powered Equipment
Automotive and Industrial
Precision Regulators
Battery Chargers
Communications
Medical Equipment
The LM4132 is available in five grades (A, B, C, D
and E) for greater flexibility. The best grade devices
(A) have an initial accuracy of 0.05% with a specified
temperature coefficient of 10 ppm/°C or less, while
the lowest grade devices (E) have an initial accuracy
of 0.5% and a tempco of 30 ppm/°C.
Device Information(1)
PART NUMBER
LM4132,
LM4132-Q1
PACKAGE
SOT-23 (5)
BODY SIZE (NOM)
2.90 mm × 1.60 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Simplified Schematic
Input
5V
VIN
CIN*
LM4132
Enable
Output
2.5V
VREF
*
COUT
EN
GND
*The capacitor CIN is required and the capacitor COUT is optional.
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
6.1
6.2
6.3
6.4
6.5
Absolute Maximum Ratings ...................................... 3
ESD Ratings.............................................................. 4
Recommended Operating Conditions....................... 4
Thermal Information .................................................. 4
Electrical Characteristics LM4132-1.8
(VOUT = 1.8 V) ............................................................ 5
6.6 Electrical Characteristics LM4132-2
(VOUT = 2.048 V) ........................................................ 6
6.7 Electrical Characteristics LM4132-2.5
(VOUT = 2.5 V) ............................................................ 7
6.8 Electrical Characteristics LM4132-3 (VOUT = 3 V) .... 8
6.9 Electrical Characteristics LM4132-3.3
(VOUT = 3.3 V) ............................................................ 9
6.10 Electrical Characteristics LM4132-4.1
(VOUT = 4.096 V) ...................................................... 10
6.11 Typical Characteristics .......................................... 11
7
Detailed Description ............................................ 19
7.1
7.2
7.3
7.4
8
Overview .................................................................
Functional Block Diagram .......................................
Feature Description.................................................
Device Functional Modes........................................
19
19
19
20
Applications and Implementation ...................... 21
8.1 Application Information............................................ 21
8.2 Typical Applications ................................................ 21
9 Power Supply Recommendations...................... 24
10 Layout................................................................... 25
10.1 Layout Guidelines ................................................. 25
10.2 Layout Example .................................................... 25
11 Device and Documentation Support ................. 26
11.1
11.2
11.3
11.4
11.5
11.6
Documentation Support ........................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
26
26
26
26
26
26
12 Mechanical, Packaging, and Orderable
Information ........................................................... 26
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (January 2016) to Revision F
•
Page
Added correct Layout Example ............................................................................................................................................ 25
Changes from Revision D (March 2015) to Revision E
•
Page
Added Device Information, ESD Ratings and Thermal Information tables, Feature Description section, Device
Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section. ..... 1
Changes from Revision C (April 2013) to Revision D
•
Page
Added some of the latest inclusions from new TI formatting and made available of the automotive grade for the
SOT-23 package..................................................................................................................................................................... 1
Changes from Revision B (August 2005) to Revision C
•
2
Page
Changed layout of National Data Sheet to TI format ........................................................................................................... 24
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
5 Pin Configuration and Functions
DBV Package
5-Pin SOT-23
Top View
N/C 1
5 VREF
GND 2
EN 3
4 VIN
Pin Functions
PIN
NO.
NAME
I/O (1)
DESCRIPTION
1
N/C
—
No connect pin, leave floating
2
GND
G
Ground
3
EN
I
Enable pin
4
VIN
P
Input supply
5
VREF
P
Reference output
(1)
G: Ground; I: Input; P: Power
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2)
MIN
MAX
UNIT
–0.3
6
V
Power dissipation (TA = 25°C) (3)
350
mW
Lead temperature (soldering, 10 sec)
260
°C
Vapor phase (60 sec)
215
°C
220
°C
150
°C
Maximum voltage on any input
Voltage
Output short circuit duration
Indefinite
Infrared (15 sec)
−65
Storage temperature, Tstg
(1)
(2)
(3)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
Without PCB copper enhancements. The maximum power dissipation must be de-rated at elevated temperatures and is limited by TJMAX
(maximum junction temperature), RθJA (junction to ambient thermal resistance) and TA (ambient temperature). The maximum power
dissipation at any temperature is: PDissMAX = (TJMAX – TA) / RθJA up to the value listed in theAbsolute Maximum Ratings. RθJA for SOT23 is 164.1°C/W, TJMAX = 125°C.
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
3
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
6.2 ESD Ratings
Electrostatic discharge (1)
V(ESD)
(1)
(2)
VALUE
UNIT
±2000
V
Human-body model (HBM), per AEC Q100-002 (2)
The Human body model is a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin.
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
6.3 Recommended Operating Conditions
MIN
NOM
MAX
UNIT
Maximum input supply voltage
5.5
Maximum enable input voltage
VIN
V
20
mA
125
°C
Maximum load current
Junction temperature, TJ
–40
V
6.4 Thermal Information
LM4132, LM4132-Q1
THERMAL METRIC
(1)
DBV (SOT-23)
UNIT
5 PINS
RθJA
Junction-to-ambient thermal resistance
164.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
115.3
°C/W
RθJB
Junction-to-board thermal resistance
27.1
°C/W
ψJT
Junction-to-top characterization parameter
12.8
°C/W
ψJB
Junction-to-board characterization parameter
26.6
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
6.5 Electrical Characteristics LM4132-1.8 (VOUT = 1.8 V)
Unless otherwise specified, limits are TJ = 25°C, VIN = 5 V, and ILOAD = 0 mA.
PARAMETER
VREF
Output voltage initial
accuracy
TEST CONDITIONS
Temperature coefficient
(A Grade - 0.05%)
–0.05%
0.05%
LM4132B-1.8
(B Grade - 0.1%)
–0.1%
0.1%
LM4132C-1.8
© Grade - 0.2%)
–0.2%
0.2%
LM4132D-1.8
(D Grade - 0.4%)
–0.4%
0.4%
LM4132E-1.8
(E Grade - 0.5%)
–0.5%
0.5%
0°C ≤ TJ ≤ 85°C
10
–40°C ≤ TJ ≤ 125°C
20
LM4132B-1.8
20
LM4132C-1.8
20
LM4132D-1.8
–40°C ≤ TJ ≤ 125°C
IQ
Supply current
IQ_SD
Supply current in shutdown
ΔVREF/ΔVIN
Line regulation
ΔVREF
30
–40°C ≤ TJ ≤ 125°C
3
–40°C ≤ TJ ≤ 125°C
Load regulation
30
0 mA ≤ ILOAD ≤ 20 mA
25
–40°C ≤ TJ ≤ 125°C
1000 Hrs
50
Thermal hysteresis (4)
–40°C ≤ TJ ≤ 125°C
75
ILOAD = 10 mA
Output noise voltage
0.1 Hz to 10 Hz
Short circuit current
–40°C ≤ TJ ≤ 125°C
VIL
Enable pin maximum low input level
–40°C ≤ TJ ≤ 125°C
VIH
Enable pin minimum high input level
–40°C ≤ TJ ≤ 125°C
ppm/V
120
Long-term stability (3)
ISC
µA
7
VREF + 400 mV ≤ VIN ≤ 5.5 V
VN
µA
100
EN = 0 V
Dropout voltage (5)
(2)
(3)
(4)
(5)
ppm/°C
60
VIN – VREF
(1)
UNIT
20
LM4132E-1.8
ΔVREF/ΔILOAD
MAX (1)
LM4132A-1.8
LM4132A-1.8
TCVREF/°C
MIN (1) TYP (2)
ppm/mA
ppm
230
–40°C ≤ TJ ≤ 125°C
mV
400
170
µVPP
75
35% (VIN)
65% (VIN)
mA
V
V
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
Typical numbers are at 25°C and represent the most likely parametric norm.
Long-term stability is VREF at 25°C measured during 1000 hrs.
Thermal hysteresis is defined as the change in 25°C output voltage before and after cycling the device from (–40°C to 125°C).
Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5-V input.
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
5
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
6.6 Electrical Characteristics LM4132-2 (VOUT = 2.048 V)
Unless otherwise specified, limits are TJ = 25°C, VIN = 5 V, and ILOAD = 0 mA.
PARAMETER
Output voltage initial
accuracy
VREF
Temperature coefficient
(A Grade - 0.05%)
–0.05%
0.05%
LM4132B-2.0
(B Grade - 0.1%)
–0.1%
0.1%
LM4132C-2.0
© Grade - 0.2%)
–0.2%
0.2%
LM4132D-2.0
(D Grade - 0.4%)
–0.4%
0.4%
LM4132E-2.0
(E Grade - 0.5%)
–0.5%
0.5%
0°C ≤ TJ ≤ 85°C
10
–40°C ≤ TJ ≤ 125°C
20
LM4132B-2.0
20
LM4132C-2.0
20
LM4132D-2.0
–40°C ≤ TJ ≤ 125°C
IQ
Supply current
IQ_SD
Supply current in shutdown
ΔVREF/ΔVIN
Line regulation
ΔVREF
30
–40°C ≤ TJ ≤ 125°C
30
0mA ≤ ILOAD ≤ 20mA
25
–40°C ≤ TJ ≤ 125°C
1000 Hrs
50
Thermal hysteresis (4)
–40°C ≤ TJ ≤ 125°C
75
ILOAD = 10 mA
Output noise voltage
0.1 Hz to 10 Hz
Short circuit current
–40°C ≤ TJ ≤ 125°C
VIL
Enable pin maximum low input level
–40°C ≤ TJ ≤ 125°C
VIH
Enable pin minimum high input level
–40°C ≤ TJ ≤ 125°C
ppm/V
120
Long term stability (3)
ISC
µA
7
VREF + 400 mV ≤ VIN ≤ 5.5 V
VN
6
3
–40°C ≤ TJ ≤ 125°C
Load regulation
µA
100
EN = 0V
Dropout voltage (5)
(2)
(3)
(4)
(5)
ppm/°C
60
VIN – VREF
(1)
UNIT
20
LM4132E-2.0
ΔVREF/ΔILOAD
MAX (1)
LM4132A-2.0
LM4132A-2.0
TCVREF/°C
MIN (1) TYP (2)
TEST CONDITIONS
ppm/mA
ppm
175
–40°C ≤ TJ ≤ 125°C
mV
400
190
µVPP
75
35% (VIN)
65% (VIN)
mA
V
V
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
Typical numbers are at 25°C and represent the most likely parametric norm.
Long-term stability is VREF at 25°C measured during 1000 hrs.
Thermal hysteresis is defined as the change in 25°C output voltage before and after cycling the device from (–40°C to 125°C).
Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5-V input.
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
6.7 Electrical Characteristics LM4132-2.5 (VOUT = 2.5 V)
Unless otherwise specified, limits are TJ = 25°C, VIN = 5 V, and ILOAD = 0 mA.
PARAMETER
VREF
Output voltage initial
accuracy
TEST CONDITIONS
Temperature coefficient
(A Grade - 0.05%)
–0.05%
0.05%
LM4132B-2.5
(B Grade - 0.1%)
–0.1%
0.1%
LM4132C-2.5
© Grade - 0.2%)
–0.2%
0.2%
LM4132D-2.5
(D Grade - 0.4%)
–0.4%
0.4%
LM4132E-2.5
(E Grade - 0.5%)
–0.5%
0.5%
0°C ≤ TJ ≤ 85°C
10
–40°C ≤ TJ ≤ 125°C
20
LM4132B-2.5
20
LM4132C-2.5
20
LM4132D-2.5
–40°C ≤ TJ ≤ 125°C
IQ
Supply current
IQ_SD
Supply current in shutdown
ΔVREF/ΔVIN
Line regulation
ΔVREF
30
–40°C ≤ TJ ≤ 125°C
3
–40°C ≤ TJ ≤ 125°C
Load regulation
50
0 mA ≤ ILOAD ≤ 20 mA
25
–40°C ≤ TJ ≤ 125°C
1000 Hrs
50
Thermal hysteresis (4)
–40°C ≤ TJ ≤ 125°C
75
ILOAD = 10 mA
Output noise voltage
0.1 Hz to 10 Hz
Short circuit current
–40°C ≤ TJ ≤ 125°C
VIL
Enable pin maximum low input level
–40°C ≤ TJ ≤ 125°C
VIH
Enable pin minimum high input level
–40°C ≤ TJ ≤ 125°C
ppm/V
120
Long term stability (3)
ISC
µA
7
VREF + 400 mV ≤ VIN ≤ 5.5 V
VN
µA
100
EN = 0 V
Dropout voltage (5)
(2)
(3)
(4)
(5)
ppm/°C
60
VIN – VREF
(1)
UNIT
20
LM4132E-2.5
ΔVREF/ΔILOAD
MAX (1)
LM4132A-2.5
LM4132A-2.5
TCVREF/°C
MIN (1) TYP (2)
ppm/mA
ppm
175
–40°C ≤ TJ ≤ 125°C
mV
400
240
µVPP
75
35% (VIN)
65% (VIN)
mA
V
V
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
Typical numbers are at 25°C and represent the most likely parametric norm.
Long-term stability is VREF at 25°C measured during 1000 hrs.
Thermal hysteresis is defined as the change in 25°C output voltage before and after cycling the device from (–40°C to 125°C).
Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5-V input.
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
7
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
6.8 Electrical Characteristics LM4132-3 (VOUT = 3 V)
Unless otherwise specified, limits are TJ = 25°C, VIN = 5 V, and ILOAD = 0 mA.
PARAMETER
Output voltage initial
accuracy
VREF
Temperature coefficient
(A Grade - 0.05%)
–0.05%
0.05%
LM4132B-3.0
(B Grade - 0.1%)
–0.1%
0.1%
LM4132C-3.0
© Grade - 0.2%)
–0.2%
0.2%
LM4132D-3.0
(D Grade - 0.4%)
–0.4%
0.4%
LM4132E-3.0
(E Grade - 0.5%)
–0.5%
0.5%
0°C ≤ TJ ≤ 85°C
10
–40°C ≤ TJ ≤ 125°C
20
LM4132B-3.0
20
LM4132C-3.0
20
LM4132D-3.0
–40°C ≤ TJ ≤ 125°C
IQ
Supply current
IQ_SD
Supply current in shutdown
ΔVREF/ΔVIN
Line regulation
ΔVREF
30
–40°C ≤ TJ ≤ 125°C
70
0mA ≤ ILOAD ≤ 20 mA
25
–40°C ≤ TJ ≤ 125°C
1000 Hrs
50
Thermal hysteresis (4)
–40°C ≤ TJ ≤ 125°C
75
ILOAD = 10 mA
Output noise voltage
0.1 Hz to 10 Hz
Short circuit current
–40°C ≤ TJ ≤ 125°C
VIL
Enable pin maximum low input level
–40°C ≤ TJ ≤ 125°C
VIH
Enable pin minimum high input level
–40°C ≤ TJ ≤ 125°C
ppm/V
120
Long term stability (3)
ISC
µA
7
VREF + 400 mV ≤ VIN ≤ 5.5 V
VN
8
3
–40°C ≤ TJ ≤ 125°C
Load regulation
µA
100
EN = 0 V
Dropout voltage (5)
(2)
(3)
(4)
(5)
ppm/°C
60
VIN – VREF
(1)
UNIT
20
LM4132E-3.0
ΔVREF/ΔILOAD
MAX (1)
LM4132A-3.0
LM4132A-3.0
TCVREF/°C
MIN (1) TYP (2)
TEST CONDITIONS
ppm/mA
ppm
175
–40°C ≤ TJ ≤ 125°C
mV
400
285
µVPP
75
35% (VIN)
65% (VIN)
mA
V
V
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
Typical numbers are at 25°C and represent the most likely parametric norm.
Long-term stability is VREF at 25°C measured during 1000 hrs.
Thermal hysteresis is defined as the change in 25°C output voltage before and after cycling the device from (–40°C to 125°C).
Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5-V input.
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
6.9 Electrical Characteristics LM4132-3.3 (VOUT = 3.3 V)
Unless otherwise specified, limits are TJ = 25°C, VIN = 5 V, and ILOAD = 0 mA.
PARAMETER
VREF
Output voltage initial
accuracy
TEST CONDITIONS
Temperature coefficient
(A Grade - 0.05%)
–0.05%
0.05%
LM4132B-3.3
(B Grade - 0.1%)
–0.1%
0.1%
LM4132C-3.3
© Grade - 0.2%)
–0.2%
0.2%
LM4132D-3.3
(D Grade - 0.4%)
–0.4%
0.4%
LM4132E-3.3
(E Grade - 0.5%)
–0.5%
0.5%
0°C ≤ TJ ≤ 85°C
10
–40°C ≤ TJ ≤ 125°C
20
LM4132B-3.3
20
LM4132C-3.3
20
LM4132D-3.3
–40°C ≤ TJ ≤ 125°C
IQ
Supply current
IQ_SD
Supply current in shutdown
ΔVREF/ΔVIN
Line regulation
ΔVREF
30
–40°C ≤ TJ ≤ 125°C
3
–40°C ≤ TJ ≤ 125°C
Load Regulation
85
0 mA ≤ ILOAD ≤ 20 mA
25
–40°C ≤ TJ ≤ 125°C
1000 Hrs
50
Thermal hysteresis (4)
–40°C ≤ TJ ≤ 125°C
75
ILOAD = 10 mA
Output noise voltage
0.1 Hz to 10 Hz
Short circuit current
–40°C ≤ TJ ≤ 125°C
VIL
Enable pin maximum low input level
–40°C ≤ TJ ≤ 125°C
VIH
Enable pin minimum high input level
–40°C ≤ TJ ≤ 125°C
ppm/V
120
Long term stability (3)
ISC
µA
7
VREF + 400 mV ≤ VIN ≤ 5.5 V
VN
µA
100
EN = 0V
Dropout voltage (5)
(2)
(3)
(4)
(5)
ppm/°C
60
VIN – VREF
(1)
UNIT
20
LM4132E-3.3
ΔVREF/ΔILOAD
MAX (1)
LM4132A-3.3
LM4132A-3.3
TCVREF/°C
MIN (1) TYP (2)
ppm/mA
ppm
175
–40°C ≤ TJ ≤ 125°C
mV
400
310
µVPP
75
35% (VIN)
65% (VIN)
mA
V
V
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
Typical numbers are at 25°C and represent the most likely parametric norm.
Long-term stability is VREF at 25°C measured during 1000 hrs.
Thermal hysteresis is defined as the change in 25°C output voltage before and after cycling the device from (–40°C to 125°C).
Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5-V input.
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
9
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
6.10 Electrical Characteristics LM4132-4.1 (VOUT = 4.096 V)
Unless otherwise specified, limits are TJ = 25°C, VIN = 5 V, and ILOAD = 0 mA.
PARAMETER
Output voltage initial
accuracy
VREF
Temperature coefficient
(A Grade - 0.05%)
–0.05%
0.05%
LM4132B-4.1
(B Grade - 0.1%)
–0.1%
0.1%
LM4132C-4.1
© Grade - 0.2%)
–0.2%
0.2%
LM4132D-4.1
(D Grade - 0.4%)
–0.4%
0.4%
LM4132E-4.1
(E Grade - 0.5%)
–0.5%
0.5%
0°C ≤ TJ ≤ 85°C
10
–40°C ≤ TJ ≤ 125°C
20
LM4132B-4.1
20
LM4132C-4.1
20
LM4132D-4.1
–40°C ≤ TJ ≤ 125°C
IQ
Supply current
IQ_SD
Supply current in shutdown
ΔVREF/ΔVIN
Line regulation
ΔVREF
30
–40°C ≤ TJ ≤ 125°C
100
0 mA ≤ ILOAD ≤ 20 mA
120
Long term stability (3)
1000 Hrs
50
Thermal hysteresis (4)
–40°C ≤ TJ ≤ 125°C
75
ILOAD = 10 mA
Output noise voltage
0.1 Hz to 10 Hz
Short circuit current
–40°C ≤ TJ ≤ 125°C
VIL
Enable pin maximum low input level
–40°C ≤ TJ ≤ 125°C
VIH
Enable pin minimum high input level
–40°C ≤ TJ ≤ 125°C
ppm/V
25
–40°C ≤ TJ ≤ 125°C
ISC
µA
7
VREF + 400 mV ≤ VIN ≤ 5.5 V
VN
10
3
–40°C ≤ TJ ≤ 125°C
Load regulation
µA
100
EN = 0V
Dropout voltage (5)
(2)
(3)
(4)
(5)
ppm/°C
60
VIN – VREF
(1)
UNIT
20
LM4132E-4.1
ΔVREF/ΔILOAD
MAX (1)
LM4132A-4.1
LM4132A-4.1
TCVREF/°C
MIN (1) TYP (2)
TEST CONDITIONS
ppm/mA
ppm
175
–40°C ≤ TJ ≤ 125°C
mV
400
350
µVPP
75
35% (VIN)
65% (VIN)
mA
V
V
Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
Typical numbers are at 25°C and represent the most likely parametric norm.
Long-term stability is VREF at 25°C measured during 1000 hrs.
Thermal hysteresis is defined as the change in 25°C output voltage before and after cycling the device from (–40°C to 125°C).
Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5-V input.
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
6.11 Typical Characteristics
100
450
VREF = 2.048V
400
VDROPOUT (mV)
SUPPLY CURRENT (PA)
2.048V
350
300
250
200
150
2.5V
100
4.096V
50
0
2
7
12
17
80
125oC
60
25oC
40
-40oC
20
0
0.5
22
1.5
Figure 1. Dropout vs Load To 0.5% Accuracy
2.5
4.5
VEN (V)
IQ SHUTDOWN (PA)
5.0
tVIHt
tVILt
1
0.5
4.0
3.5
3.0
2.0
2
2.5
3
3.5
4
4.5
5
-40
25
50
75
100
125
Figure 4. Shutdown IQ vs Temperature
200
85
50
150
-50
-100
80
GROUND CURRENT (PA)
1 TYPICAL UNIT FROM EACH
VOLTAGE OPTION
100
DRIFT (ppm)
0
TEMPERATURE ( C)
VIN (V)
75
70
65
60
-150
-200
-25
o
Figure 3. Enable Threshold Voltage and Hysteresis
0
5.5
2.5
0
150
4.5
Figure 2. Supply Current vs Input Voltage
3
1.5
3.5
INPUT VOLTAGE (V)
ILOAD (mA)
2
2.5
0 100 200 300 400 500 600 700 800 900 1000
55
0
TIME (Hours)
5
10
15
20
LOAD CURRENT (mA)
Figure 5. Typical Long-Term Stability
Figure 6. Ground Current vs Load Current
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
11
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
Typical Characteristics (continued)
45
Temperature Range
-40oC < TJ < 125oC
after 8 thermal cycles
40
FREQUENCY
35
30
25
20
15
10
5
0
0
25
50
75 100 125 150 200
HYSTERESIS (ppm)
Figure 7. Typical Thermal Hysteresis
Figure 8. Turnon Transient Response
ILOAD = 0 To 10 mA
VIN = 4 V To 5.5 V
Figure 9. Load Transient Response
12
Submit Documentation Feedback
Figure 10. Line Transient Response
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
6.11.1 Typical Characteristics for 1.8 V
1.804
1.8010
1.803
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.8005
1.802
5 TYPICAL UNITS
1.801
1.800
1.799
1.798
125oC
1.8000
1.7995
25oC
1.7990
-40oC
1.7985
1.797
1.796
-40
1.7980
-20
0
20
40
60
80 100 120
0
2
4
TEMPERATURE (oC)
6
8
10 12 14 16 18 20
LOAD CURRENT (mA)
Figure 12. Load Regulation
Figure 11. Output Voltage vs Temperature
1.8020
OUTPUT VOLTAGE (V)
1.8015
1.8010
125oC
1.8005
25oC
1.8000
1.7995
-40oC
1.7990
1.7985
1.7990
2.2
2.7
3.2
3.7
4.2
4.7
5.2
INPUT VOLTAGE (V)
Figure 13. Line Regulation
Figure 14. 0.1–10 Hz Noise
0
POWER SUPPLY REJECTION (dB)
OUTPUT NOISE VOLTAGE (PV/rt(Hz))
16
14
NO COUT
12
10
8
6
4
2
0
10
100
1k
10k
-10
NO COUT
-20
-30
-40
-50
-60
-70
COUT = 0.1 PF
-80
-90
10
FREQUENCY (Hz)
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 15. Output Voltage Noise Spectrum
Figure 16. Power Supply Rejection vs Frequency
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
13
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
6.11.2 Typical Characteristics for 2.048 V
2.050
2.052
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
2.051
2.050
5 TYPICAL UNITS
2.049
2.048
2.047
2.048
25oC
-40oC
2.047
125oC
2.046
2.046
2.045
-50
2.049
-25
0
25
50
75
100
2.045
0
125
4
o
TEMPERATURE ( C)
8
12
16
20
LOAD CURRENT (mA)
Figure 18. Load Regulation
Figure 17. Output Voltage vs Temperature
2.052
OUTPUT VOLTAGE (V)
2.051
125oC
2.050
25oC
2.049
2.048
-40oC
2.047
2.046
2.5
3.0
3.5
4.0
4.5
5.0
5.5
INPUT VOLTAGE (V)
Figure 20. 0.1–10 Hz Noise
Figure 19. Line Regulation
0
POWER SUPPLY REJECTION (dB)
OUTPUT NOISE VOLTAGE (PV/rt(Hz))
16
14
NO COUT
12
10
8
6
4
2
0
10
-10
-20
-30
NO COUT
-40
-50
-60
-70
COUT = 0.1 PF
-80
100
1k
10k
10
100
FREQUENCY (Hz)
Submit Documentation Feedback
10k
100k
1M
FREQUENCY (Hz)
Figure 21. Output Voltage Noise Spectrum
14
1k
Figure 22. Power Supply Rejection vs Frequency
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
6.11.3 Typical Characteristics for 2.5 V
2.504
2.503
5 TYPICAL UNITS
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
2.503
2.502
2.501
2.500
2.499
2.502
-40oC
2.501
2.500
125oC
2.499
2.498
2.497
-50
25oC
-25
0
25
50
75
100
2.498
0
125
4
o
TEMPERATURE ( C)
8
12
16
20
LOAD CURRENT (mA)
Figure 23. Output Voltage vs Temperature
Figure 24. Load Regulation
2.502
OUTPUT VOLTAGE (V)
125oC
2.501
2.500
25oC
-40oC
2.499
2.498
2.497
3.0
3.5
4.0
4.5
5.0
5.5
INPUT VOLTAGE (V)
Figure 25. Line Regulation
Figure 26. 0.1–10 Hz Noise
0
POWER SUPPLY REJECTION (dB)
OUTPUT NOISE VOLTAGE (PV/rt(Hz))
32
28
NO COUT
24
20
16
12
8
4
0
-10
NO COUT
-20
-30
-40
-50
-60
COUT = 0.1 PF
-70
-80
10
100
1k
10k
10
FREQUENCY (Hz)
100
1k
10k
100k
1M
FREQUENCY (Hz)
Figure 27. Output Voltage Noise Spectrum
Figure 28. Power Supply Rejection vs Frequency
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
15
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
3.006
3.0020
3.005
3.0015
3.004
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
6.11.4 Typical Characteristics for 3 V
3.003
3.002
5 TYPICAL UNITS
3.001
3
2.999
2.998
3.0005
125oC
3.0000
2.9995
25oC
2.9990
2.9985
-40oC
2.9980
2.997
2.996
-40
3.0010
2.9975
-20
0
20
40
60
0
80 100 120
2
o
TEMPERATURE ( C)
4
6
8
10 12 14 16 18 20
LOAD CURRENT (mA)
Figure 30. Load Regulation
Figure 29. Output Voltage vs Temperature
3.0020
OUTPUT VOLTAGE (V)
3.0015
125oC
3.0010
3.0005
25oC
3.0000
2.9995
2.9990
-40oC
2.9985
2.9980
3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
INPUT VOLTAGE (V)
Figure 32. 0.1–10 Hz Noise
Figure 31. Line Regulation
25
NO COUT
20
15
10
5
0
10
16
0
POWER SUPPLY REJECTION (dB)
OUTPUT NOISE VOLTAGE PV (Hz))
30
100
1k
10k
-10
NO COUT
-20
-30
-40
-50
-60
-70
COUT = 0.1 PF
-80
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 33. Output Voltage Noise Spectrum
Figure 34. Power Supply Rejection vs Frequency
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
6.11.5 Typical Characteristics for 3.3 V
3.305
3.3005
3.304
3.3000
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
3.303
5 TYPICAL UNITS
3.302
3.301
3.3
3.299
3.298
3.297
-40oC
3.2995
3.2990
25oC
3.2985
125oC
3.2980
3.296
3.295
-40
3.2975
-20
0
20
40
60
0
80 100 120
2
4
o
6
8
10 12 14 16 18 20
LOAD CURRENT (mA)
TEMPERATURE ( C)
Figure 36. Load Regulation
Figure 35. Output Voltage vs Temperature
3.3010
OUTPUT VOLTAGE (V)
3.3008
25oC
3.3006
3.3004
3.3002
125oC
3.3000
-40oC
3.2998
3.2996
3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
INPUT VOLTAGE (V)
Figure 37. Line Regulation
Figure 38. 0.1–10 Hz Noise
0
POWER SUPPLY REJECTION (dB)
OUTPUT NOISE VOLTAGE PV (Hz))
30
25
NO COUT
20
15
10
5
0
10
100
1k
10k
-10
NO COUT
-20
-30
-40
-50
COUT = 0.1 PF
-60
-70
-80
-90
10
100
1k
10k
100k
1M
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 39. Output Voltage Noise Spectrum
Figure 40. Power Supply Rejection vs Frequency
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
17
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
6.11.6 Typical Characteristics for 4.096 V
4.104
4.098
-40oC
5 TYPICAL UNITS
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
4.102
4.100
4.098
4.096
4.094
4.096
125oC
4.095
25oC
4.094
4.092
4.090
-50
4.097
-25
0
25
50
75
100
4.093
0
125
4
TEMPERATURE (oC)
8
12
16
20
LOAD CURRENT (mA)
Figure 42. Load Regulation
Figure 41. Output Voltage vs Temperature
4.100
OUTPUT VOLTAGE (V)
4.099
4.098
125oC
4.097
4.096
4.095
-40oC
4.094
25oC
4.093
4.092
4.5
4.7
4.9
5.1
5.3
5.5
INPUT VOLTAGE (V)
Figure 43. Line Regulation
Figure 44. 0.1–10 Hz Noise
POWER SUPPLY REJECTION RATIO (dB)
OUTPUT NOISE VOLTAGE (PV/rt(Hz))
32
28
NO COUT
24
20
16
12
8
4
0
10
100
1k
10k
0
-10
NO COUT
-20
-30
-40
-50
-60
COUT = 0.1 PF
-70
-80
10
100
FREQUENCY (Hz)
Submit Documentation Feedback
10k
100k
1M
FREQUENCY (Hz)
Figure 45. Output Voltage Noise Spectrum
18
1k
Figure 46. Power Supply Rejection vs Frequency
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
7 Detailed Description
7.1 Overview
The LM4132 device is a precision bandgap voltage reference available in 6 different voltages with 20-mA current
source capability. This series reference can operate with input voltages from VREF + 400 mV to 5.5 V while
consuming 60-µA (typical) supply current. In shutdown mode, current drops to 3 µA (typical). The LM4132 is
available in five grades from A and E.
The best grade devices (A) have an initial accuracy of 0.05% with a specified tempco of 10 ppm/°C from –40°C
to 125°C. The grade devices (E) have an initial accuracy of 0.5% with specified tempco of 30 ppm/°C from –40°C
to 125°C.
7.2 Functional Block Diagram
VIN
VBG
BANDGAP
CELL
±
Q1
+
ILOAD
VREF
EN
§
R1 ·
VBG ¨ 1
¸
© R2 ¹
R1
COUT
R2
7.3 Feature Description
The LM4132 can be remotely operated by applying an EN voltage between 65% of VIN, and VIN. The LM4312
can be remotely disabled by applying an EN voltage between 0 V to 35% of VIN. The EN pin can also be
strapped to VIN, so VREF is active when VIN is applied.
7.3.1 Short Circuited Output
The LM4132 features indefinite short circuit protection. This protection limits the output current to 75 mA when
the output is shorted to ground.
7.3.2 Turnon Time
Turnon time is defined as the time taken for the output voltage to rise to 90% of the preset value. The turnon time
depends on the load. The turnon time is typically 33.2 µs when driving a 1-µF load and 78.8 µs when driving a
10-µF load. Some users may experience an extended turnon time (up to 10 ms) under brown-out conditions and
low temperatures (–40°C).
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
19
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
Feature Description (continued)
7.3.3 Thermal Hysteresis
Thermal hysteresis is defined as the change in output voltage at 25ºC after some deviation from 25ºC. This is to
say that thermal hysteresis is the difference in output voltage between two points in a given temperature profile.
An illustrative temperature profile is shown in Figure 47.
125oC
VREF1
25oC
Time
VREF2
-40oC
Figure 47. Temperature Profile
This may be expressed analytically by Equation 1:
VHYS =
lVREF1 - VREF2l
x 106 ppm
VREF
where
•
•
•
•
•
VHYS = Thermal hysteresis expressed in ppm
VREF = Nominal preset output voltage
VREF1 = VREF before temperature fluctuation
VREF2 = VREF after temperature fluctuation
The LM4132 features a low thermal hysteresis of 75 ppm (typical) from –40°C to 125°C after 8 temperature
cycles.
(1)
7.4 Device Functional Modes
Table 1 describes the functional modes of the LM4132.
Table 1. Enable Pin Mode Summary
20
ENABLE PIN CONNECTION
LOGIC STATE
DESCRIPTION
EN = VIN
1
Normal operation — LM4132 starts up.
EN = GND
0
The LM4312 is in shutdown mode.
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
8 Applications and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The LM4132 family of precision voltage references can deliver up to 20 mA without an output capacitor or buffer
amplifier. The LM4132 is ideal for battery-powered solutions, with a low quiescent current of 60 µA, and a low
dropout voltage of 400 mV. The LM4132 enters the shutdown mode (3 µA, typical) when EN is 0 V.
8.2 Typical Applications
8.2.1 LM4132 Typical Application
Input
5V
VIN
Output
2.5V
VREF
CIN*
LM4132
*
COUT
EN
Enable
GND
8.2.1.1 Design Requirements
For this design example, use the parameters listed as the input parameters.
• VIN > VREF + 400 mV (ILOAD ≤ 10 mA)
• ILOAD ≤ 20 mA
• The LM4132 is enabled when 65%VIN< VEN ≤ VIN. VEN cannot be greater than VIN; otherwise, the device does
not operate correctly.
• The devices is disabled when 0 V ≤ VEN ≤ 35%VIN.
8.2.1.2 Detailed Design Procedure
The foundation of any voltage reference is the band-gap circuit. While the reference in the LM4132 is developed
from the gate-source voltage of transistors in the device, principles of the band-gap circuit are easily understood
using a bipolar example. For a detailed analysis of the bipolar band-gap circuit, refer to AN 56 LM113 1.2V
Reference (SNVA514).
8.2.1.2.1 Supply and Enable Voltages
To ensure proper operation, VEN and VIN must be within a specified range. An acceptable range of input voltages
is calculated by Equation 2:
VIN > VREF + 400 mV (ILOAD ≤ 10 mA)
(2)
The EN pin uses an internal pullup current source (IPULL_UP ≊ 2 µA) that may be left floating or triggered by an
external source. If the device is not enabled by an external source, it may be connected to VIN. An acceptable
range of enable voltages is given by Figure 4. See Electrical Characteristics LM4132-1.8 (VOUT = 1.8 V) and
Figure 3 for more detail. The device does not operate correctly for VEN > VIN.
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
21
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
Typical Applications (continued)
8.2.1.2.2 Component Selection
A small ceramic (X5R or X7R) capacitor on the input must be used to ensure stable operation. The value of CIN
must be sized according to the output capacitor value. The value of CIN must satisfy the relationship CIN ≥ COUT.
When no output capacitor is used, CIN must have a minimum value of 0.1 µF. Noise on the power-supply input
may affect the output noise. Larger input capacitor values (typically 4.7 µF to 22 µF) may help reduce noise on
the output and significantly reduce overshoot during start-up. Use of an additional optional bypass capacitor from
the input and ground may help further reduce noise on the output. With an input capacitor, the LM4132 drives
any combination of resistance and capacitance up to VREF / 20 mA and 10 µF, respectively.
The LM4132 is designed to operate with or without an output capacitor and is stable with capacitive loads up to
10 µF. Connecting a capacitor from the output and ground significantly improves the load transient response
when switching from a light load to a heavy load. The output capacitor must not be made arbitrarily large
because capacitor selection affects the turnon time as well as line and load transients.
While a variety of capacitor chemistry types may be used, it is typically advisable to use low equivalent series
resistance (ESR) ceramic capacitors. Such capacitors provide a low impedance to high frequency signals,
effectively bypassing them to ground. Bypass capacitors must be mounted close to the device. Mounting bypass
capacitors close to the device helps reduce the parasitic trace components thereby improving performance.
8.2.1.2.3 Temperature Coefficient
Temperature drift is defined as the maximum deviation in output voltage over the operating temperature range.
This deviation over temperature may be shown in Figure 48:
Temperature
Change in Output Voltage
Voltage
VREF_MAX
VREF_MIN
Temperature Range
Figure 48. VREF vs Temperature Profile
Temperature coefficient may be expressed analytically as Equation 3:
TD =
(VREF_MAX - VREF_MIN)
VREF x ΔT
x 106 ppm
where
•
•
•
•
•
•
TD = Temperature drift
VREF = Nominal preset output voltage
VREF_MIN = Minimum output voltage over operating temperature range
VREF_MAX = Maximum output voltage over operating temperature range
ΔT = Operating temperature range
The LM4132 features a low temperature drift of 10 ppm (maximum) to 30 ppm (maximum), depending on the
grade.
(3)
8.2.1.2.4 Long-Term Stability
Long-term stability refers to the fluctuation in output voltage over a long period of time (1000 hours). The LM4132
features a typical long-term stability of 50 ppm over 1000 hours. The measurements are made using 5 units of
each voltage option, at a nominal input voltage (5 V), with no load, at room temperature.
22
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
Typical Applications (continued)
8.2.1.2.5 Expression Of Electrical Characteristics
Electrical characteristics are typically expressed in mV, ppm, or a percentage of the nominal value. Depending
on the application, one expression may be more useful than the other. To convert one quantity to the other one
may apply the following:
ppm to mV error in output voltage:
VREF x ppmERROR
103
= VERROR
where
•
•
VREF is in volts (V)
VERROR is in millivolts (mV)
(4)
Bit error (1 bit) to voltage error (mV):
VREF
2n
x 103 = VERROR
where
•
•
•
VREF is in volts (V)
VERROR is in millivolts (mV)
n is the number of bits
(5)
mV to ppm error in output voltage:
VERROR
VREF
x 103 = ppmERROR
where
•
•
VREF is in volts (V)
VERROR is in millivolts (mV)
(6)
Voltage error (mV) to percentage error (percent):
VERROR
VREF
x 0.1 = Percent_Error
where
•
•
VREF is in volts (V)
VERROR is in millivolts (mV)
(7)
8.2.1.3 Application Curves
2.503
2.502
2.502
2.501
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
125oC
-40oC
2.501
2.500
125oC
2.499
2.500
25oC
-40oC
2.499
2.498
25oC
2.498
0
4
8
12
16
20
2.497
3.0
3.5
4.0
4.5
5.0
LOAD CURRENT (mA)
INPUT VOLTAGE (V)
Figure 49. Load Regulation
Figure 50. Line Regulation
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
5.5
Submit Documentation Feedback
23
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
Typical Applications (continued)
8.2.2 Other Application Circuits
V REF
Input
VIN
VREF
C OUT
CIN
R
R
+5V
-VREF
LM4132
-5V
Enable
R/2
EN
GND
4.7 µF < C OUT < 10 µF
Figure 51. Voltage Reference With Complementary Output
+5V
Input
VIN
VREF
VREF_FORCE
CIN
0.1 µF
LM4132
Enable
EN
100 k:
VREF_SENSE
GND
Figure 52. Precision Voltage Reference With Force and Sense Output
Input
VIN
Output
VREF
CIN
R1
500:
LM4132
0.1 µF
Enable
EN
RSET
GND
I OUT
IOUT = (VREF/(R1 + RSET)) + IGND
IGND
RL
1 k:
Figure 53. Programmable Current Source
9 Power Supply Recommendations
Refer to Component Selection.
24
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
LM4132, LM4132-Q1
www.ti.com
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
10 Layout
10.1 Layout Guidelines
The mechanical stress due to PC board mounting can cause the output voltage to shift from its initial value. The
center of a PC board generally has the highest mechanical and thermal expansion stress. Mounting the device
near the edges or the corners of the board where mechanical stress is at its minimum. References in SOT-23
packages are generally less prone to assembly stress than devices in small outline (SOIC) packages.
A mechanical isolation of the device by creating an island by cutting a U shape slot (U - SLOT) on the PCB while
mounting the device helps in reducing the impact of the PC board stresses on the output voltage of the
reference. This approach would also provide some thermal isolation from the rest of the circuit.
Figure 54 shows a recommended printed board layout for LM4132 along with an in-set diagram, which exhibits a
slot cut on three sides of the reference device.
Bypass capacitors must be mounted close to the device. Mounting bypass capacitors close to the device reduces
the parasitic trace components thereby improving performance.
10.2 Layout Example
PCB Top View
PCB Length
VIN
VREF
LM4132
PCB Side View
STRESS
U - SLOT
N/C
GND
STRESS
EN
U - SLOT
VREF
LM4132
N/C
PCB Length
GND
Set CIN
close to VIN
and GND
EN
N/C
COUT
LM4132
CIN
VIN
Set COUT
close to VOUT
and GND
VREF
Figure 54. Typical Layout Example with LM4132
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
Submit Documentation Feedback
25
LM4132, LM4132-Q1
SNVS372F – AUGUST 2005 – REVISED MARCH 2016
www.ti.com
11 Device and Documentation Support
11.1 Documentation Support
11.1.1 Related Documentation
For related documentation see the following:
Application Note 56 LM113 1.2V Reference, SNVA514
11.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 2. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
LM4132
Click here
Click here
Click here
Click here
Click here
LM4132-Q1
Click here
Click here
Click here
Click here
Click here
11.3 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.4 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
11.6 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
26
Submit Documentation Feedback
Copyright © 2005–2016, Texas Instruments Incorporated
Product Folder Links: LM4132 LM4132-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
1-Mar-2016
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4132AMF-1.8/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AA
LM4132AMF-2.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BA
LM4132AMF-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CA
LM4132AMF-3.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DA
LM4132AMF-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4EA
LM4132AMF-4.1
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
R4FA
LM4132AMF-4.1/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FA
LM4132AMFX-1.8/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AA
LM4132AMFX-2.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BA
LM4132AMFX-2.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CA
LM4132AMFX-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DA
LM4132AMFX-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4EA
LM4132AMFX-4.1/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FA
LM4132AQ1MFR2.5
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZECX
LM4132AQ1MFR3.0
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZEIX
LM4132AQ1MFT2.5
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZECX
LM4132AQ1MFT3.0
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZEIX
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Mar-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4132BMF-1.8/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AB
LM4132BMF-2.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BB
LM4132BMF-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CB
LM4132BMF-3.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DB
LM4132BMF-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4EB
LM4132BMF-4.1
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
R4FB
LM4132BMF-4.1/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FB
LM4132BMFX-1.8/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AB
LM4132BMFX-2.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BB
LM4132BMFX-2.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CB
LM4132BMFX-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DB
LM4132BMFX-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4EB
LM4132BMFX-4.1/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FB
LM4132BQ1MFR2.5
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZDYX
LM4132BQ1MFR3.0
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZEJX
LM4132BQ1MFT2.5
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZDYX
LM4132BQ1MFT3.0
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZEJX
LM4132CMF-1.8/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AC
Addendum-Page 2
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Mar-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4132CMF-2.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BC
LM4132CMF-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CC
LM4132CMF-3.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DC
LM4132CMF-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4EC
LM4132CMF-4.1
NRND
SOT-23
DBV
5
1000
TBD
Call TI
Call TI
-40 to 125
R4FC
LM4132CMF-4.1/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FC
LM4132CMFX-1.8/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AC
LM4132CMFX-2.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BC
LM4132CMFX-2.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CC
LM4132CMFX-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DC
LM4132CMFX-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4EC
LM4132CMFX-4.1/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FC
LM4132CQ1MFR2.5
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZDZX
LM4132CQ1MFR3.0
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZEKX
LM4132CQ1MFT2.5
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZDZX
LM4132CQ1MFT3.0
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZEKX
LM4132DMF-1.8/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AD
LM4132DMF-2.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BD
Addendum-Page 3
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Mar-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4132DMF-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CD
LM4132DMF-3.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DD
LM4132DMF-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4ED
LM4132DMF-4.1/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FD
LM4132DMFX-1.8/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AD
LM4132DMFX-2.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BD
LM4132DMFX-2.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CD
LM4132DMFX-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DD
LM4132DMFX-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4ED
LM4132DMFX-4.1/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FD
LM4132DQ1MFR2.5
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZEAX
LM4132DQ1MFR3.0
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZELX
LM4132DQ1MFT2.5
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZEAX
LM4132DQ1MFT3.0
ACTIVE
SOT-23
DBV
5
250
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
ZELX
LM4132EMF-1.8/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AE
LM4132EMF-2.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BE
LM4132EMF-2.5/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CE
LM4132EMF-3.0/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DE
Addendum-Page 4
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
Orderable Device
1-Mar-2016
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Op Temp (°C)
Device Marking
(4/5)
LM4132EMF-3.3/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4EE
LM4132EMF-4.1/NOPB
ACTIVE
SOT-23
DBV
5
1000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FE
LM4132EMFX-1.8/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4AE
LM4132EMFX-2.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4BE
LM4132EMFX-2.5/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4CE
LM4132EMFX-3.0/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4DE
LM4132EMFX-3.3/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4EE
LM4132EMFX-4.1/NOPB
ACTIVE
SOT-23
DBV
5
3000
Green (RoHS
& no Sb/Br)
CU SN
Level-1-260C-UNLIM
-40 to 125
R4FE
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 5
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
1-Mar-2016
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF LM4132, LM4132-Q1 :
• Catalog: LM4132
• Automotive: LM4132-Q1
NOTE: Qualified Version Definitions:
• Catalog - TI's standard catalog product
• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
Addendum-Page 6
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Mar-2016
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LM4132AMF-1.8/NOPB
SOT-23
DBV
5
1000
178.0
8.4
LM4132AMF-2.0/NOPB
SOT-23
DBV
5
1000
178.0
LM4132AMF-2.5/NOPB
SOT-23
DBV
5
1000
178.0
LM4132AMF-3.0/NOPB
SOT-23
DBV
5
1000
LM4132AMF-3.3/NOPB
SOT-23
DBV
5
LM4132AMF-4.1
SOT-23
DBV
LM4132AMF-4.1/NOPB
SOT-23
DBV
LM4132AMFX-1.8/NOPB SOT-23
W
Pin1
(mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AMFX-2.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AMFX-2.5/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AMFX-3.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AMFX-3.3/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AMFX-4.1/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AQ1MFR2.5
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AQ1MFR3.0
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AQ1MFT2.5
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132AQ1MFT3.0
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BMF-1.8/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Mar-2016
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
LM4132BMF-2.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
LM4132BMF-2.5/NOPB
SOT-23
DBV
5
1000
178.0
8.4
LM4132BMF-3.0/NOPB
SOT-23
DBV
5
1000
178.0
LM4132BMF-3.3/NOPB
SOT-23
DBV
5
1000
178.0
LM4132BMF-4.1
SOT-23
DBV
5
1000
LM4132BMF-4.1/NOPB
W
Pin1
(mm) Quadrant
3.2
3.2
1.4
4.0
8.0
Q3
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
8.4
3.2
3.2
1.4
4.0
8.0
Q3
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BMFX-1.8/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BMFX-2.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BMFX-2.5/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BMFX-3.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BMFX-3.3/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BMFX-4.1/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BQ1MFR2.5
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BQ1MFR3.0
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BQ1MFT2.5
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132BQ1MFT3.0
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMF-1.8/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMF-2.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMF-2.5/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMF-3.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMF-3.3/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMF-4.1
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMF-4.1/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMFX-1.8/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMFX-2.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMFX-2.5/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMFX-3.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMFX-3.3/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CMFX-4.1/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CQ1MFR2.5
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CQ1MFR3.0
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CQ1MFT2.5
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132CQ1MFT3.0
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMF-1.8/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMF-2.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMF-2.5/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMF-3.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMF-3.3/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMF-4.1/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMFX-1.8/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMFX-2.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMFX-2.5/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMFX-3.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Mar-2016
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
LM4132DMFX-3.3/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DMFX-4.1/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DQ1MFR2.5
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DQ1MFR3.0
SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DQ1MFT2.5
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132DQ1MFT3.0
SOT-23
DBV
5
250
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMF-1.8/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMF-2.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMF-2.5/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMF-3.0/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMF-3.3/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMF-4.1/NOPB
SOT-23
DBV
5
1000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMFX-1.8/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMFX-2.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMFX-2.5/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMFX-3.0/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMFX-3.3/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
LM4132EMFX-4.1/NOPB SOT-23
DBV
5
3000
178.0
8.4
3.2
3.2
1.4
4.0
8.0
Q3
*All dimensions are nominal
Pack Materials-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Mar-2016
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM4132AMF-1.8/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132AMF-2.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132AMF-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132AMF-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132AMF-3.3/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132AMF-4.1
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132AMF-4.1/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132AMFX-1.8/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132AMFX-2.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132AMFX-2.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132AMFX-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132AMFX-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132AMFX-4.1/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132AQ1MFR2.5
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132AQ1MFR3.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132AQ1MFT2.5
SOT-23
DBV
5
250
210.0
185.0
35.0
LM4132AQ1MFT3.0
SOT-23
DBV
5
250
210.0
185.0
35.0
LM4132BMF-1.8/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132BMF-2.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132BMF-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132BMF-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132BMF-3.3/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132BMF-4.1
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132BMF-4.1/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132BMFX-1.8/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132BMFX-2.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132BMFX-2.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132BMFX-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132BMFX-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132BMFX-4.1/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132BQ1MFR2.5
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132BQ1MFR3.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132BQ1MFT2.5
SOT-23
DBV
5
250
210.0
185.0
35.0
LM4132BQ1MFT3.0
SOT-23
DBV
5
250
210.0
185.0
35.0
LM4132CMF-1.8/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132CMF-2.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132CMF-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132CMF-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132CMF-3.3/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132CMF-4.1
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132CMF-4.1/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132CMFX-1.8/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132CMFX-2.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132CMFX-2.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
Pack Materials-Page 4
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Mar-2016
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LM4132CMFX-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132CMFX-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132CMFX-4.1/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132CQ1MFR2.5
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132CQ1MFR3.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132CQ1MFT2.5
SOT-23
DBV
5
250
210.0
185.0
35.0
LM4132CQ1MFT3.0
SOT-23
DBV
5
250
210.0
185.0
35.0
LM4132DMF-1.8/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132DMF-2.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132DMF-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132DMF-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132DMF-3.3/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132DMF-4.1/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132DMFX-1.8/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132DMFX-2.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132DMFX-2.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132DMFX-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132DMFX-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132DMFX-4.1/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132DQ1MFR2.5
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132DQ1MFR3.0
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132DQ1MFT2.5
SOT-23
DBV
5
250
210.0
185.0
35.0
LM4132DQ1MFT3.0
SOT-23
DBV
5
250
210.0
185.0
35.0
LM4132EMF-1.8/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132EMF-2.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132EMF-2.5/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132EMF-3.0/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132EMF-3.3/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132EMF-4.1/NOPB
SOT-23
DBV
5
1000
210.0
185.0
35.0
LM4132EMFX-1.8/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132EMFX-2.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132EMFX-2.5/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132EMFX-3.0/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132EMFX-3.3/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
LM4132EMFX-4.1/NOPB
SOT-23
DBV
5
3000
210.0
185.0
35.0
Pack Materials-Page 5
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2016, Texas Instruments Incorporated