Finisar Product Specification CWDM Extended Temperature GBIC Transceiver FTR-1621T-XX PRODUCT FEATURES • All Metro data protocols from 622Mb/s to 2.7 Gb/s • Extended link budget with APD receiver technology • Standard GBIC footprint • Cooled CWDM DFB laser transmitter • Class 1 laser eye safety • Very low jitter • Metal enclosure for lower EMI • Extended voltage range • Low power dissipation • Extended operating temperature range: -40°C to 85°C APPLICATIONS • Metro Access Rings and Pointto-Point networking for SONET, Gigabit Ethernet and Fibre Channel Finisar’s FTR-1621T-XX CWDM Extended Temperature GBIC transceivers comply with GBIC Specification Revision 5.51*. They are compatible with Gigabit Ethernet as specified in IEEE 802.32*, single and double rate Fibre Channel FC-PH, PH2, PH33* and SONET specifications for OC-12/OC-48 4**. Along with an extraordinary operation range of –40oC to 85oC, the fiber link budget has been enhanced with an Avalanche Photo Diode (APD) receiver. Additional real time diagnostic functions are available via the 2-wire serial bus specified for Module Definition “4” GBICs. For details, see Finisar Application Note AN-2030, “Digital Diagnostic Monitoring Interface for Optical Transceivers”5. Even with all of these innovative features, the transceiver is still compliant with the mechanical and electrical interfaces defined in the GBIC interoperability standard. © Finisar Corporation December 2004 Rev E Page 1 FTR-1621T-XX WDM GBIC Product Specification – December 2004 Finisar PRODUCT SELECTION FTR-1621T-XX Wavelength 1470 nm 1490 nm 1510 nm 1530 nm I. XX 47 49 51 53 Color Code Dot Gray Violet Blue Green Wavelength 1550 nm 1570 nm 1590 nm 1610 nm XX 55 57 59 61 Color Code Dot Yellow Orange Red Brown Pin Out Pin Name Pin # Sequence RX_LOS 1 2 GND 2 2 GND 3 2 MOD_DEF(0) 4 2 MOD_DEF(1) 5 2 MOD_DEF(2) 6 2 TX_DISABLE 7 2 GND 8 2 GND 9 2 TX_FAULT 10 2 GND 11 1 -RX_DAT 12 1 +RX_DAT 13 1 GND 14 1 VCC 15 2 VCC 16 2 GND 17 1 +TX_DAT 18 1 -TX_DAT 19 1 GND 20 1 Table 1. GBIC to host connector pin assignment “Sequence” indicates the order in which pins make contact when the device is hot plugged. Also see “Table 3: Signal Definitions” in the GBIC Specification Revision 5.5.1 © Finisar Corporation December 2004 Rev E Page 2 FTR-1621T-XX WDM GBIC II. Product Specification – December 2004 Finisar Electrical Power Interface Parameter Supply Current Maximum Voltage Symbol Is Vmax Surge Current Min Typ 280 Isurge Input Voltage Vcc 4.75 Power Supply Rejection PSR 100 5.00 Max 450 6 Units mA V 30 mA 5.25 V mV Notes/Conditions Above DC current level for < 300 ms Referenced to GND See Note 1. Peak to Peak Table 2. Electrical power interface Note 1: Receiver sensitivity is compliant with power supply sinusoidal of 20 Hz to 1.5Mhz up to specified value applied through the recommended power supply filtering network III. Low Speed Signals RX_LOS, TX_DISABLE, and TX_FAULT are TTL signals as described in Table 3. MOD_DEF(1) (SCL) and MOD_DEF(2) (SDA) are open drain CMOS signals (see section VIII, “Serial Communication Protocol”). Both MOD_DEF(1) and MOD_DEF(2) must be pulled up to host_Vcc. Note – MOD_DEF(0) is grounded inside the GBIC to indicate the correct mode of operation. For more detailed information, see sections 5.3.1 – 5.3.8 in the GBIC Specification Rev. 5.51. Parameter GBIC Output LOW GBIC Output HIGH GBIC Input LOW GBIC Input HIGH Symbol VOL Min 0 Units Notes/Conditions V 4.7k to 10k pull-up to host_Vcc, measured at host side of connector VOH host_Vcc - host_Vcc + V 4.7k to 10k pull-up to host_Vcc, 0.5 0.3 measured at host side of connector VIL 0 0.8 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector VIH 2 Vcc + 0.3 V 4.7k to 10k pull-up to Vcc, measured at GBIC side of connector Table 3. Low speed signals – electronic characteristics © Finisar Corporation December 2004 Rev E Max 0.5 Page 3 FTR-1621T-XX WDM GBIC Product Specification – December 2004 Parameter RX_LOS Assert Level RX_LOS Deassert Level RX_LOS Hysterisis RX_LOS Assert Delay Symbol Min --40 --t_loss_on RX_LOS Negate Delay 400 Units dBm dBm dB µsec t_loss_off 150 µsec TX_DISABLE Assert Time t_off 1500 µsec TX_DISABLE Negate Time t_on 6000 µsec TX_DISABLE Reset Time t_reset Typ -36 -34 2.0 Max -30 µsec 10 Finisar Notes/Conditions Measured on Finisar Eval Card Measured on Finisar Eval Card Measured on Finisar Eval Card From detection of loss of signal to assertion of RX_LOS From detection of presence of signal to negation of RX_LOS Rising edge to TX_DISABLE to fall of output signal below 10% of nominal Falling edge of TX_DISABLE to rise of output signal above 90% of nominal TX_DISABLE HIGH before TX_DISABLE set LOW Table 4. Low speed signal parameters IV. High Speed Electrical Interface All high-speed PECL signals are AC coupled internally. Parameter Data Input Voltage Data Output Voltage Duty Cycle PECL rise/fall Bit Error Rate Symbol Vin Vout -Tr,Tf BER Tx Input Impedance Rx Output Impedance Zin Zout Min 650 370 Typ Max 2000 2000 50 150 10-12 75 75 Units mV mV % psec ohm ohm Notes/Conditions PECL differential peak - peak PECL differential peak - peak 20%-80% Differential PRBS 223 - 1 test data pattern Singled ended impedance Singled ended impedance Table 5. High speed electrical interface © Finisar Corporation December 2004 Rev E Page 4 FTR-1621T-XX WDM GBIC V. Finisar Product Specification – December 2004 Optical Parameters Parameter Symbol TRANSMITTER CHARACTERISTICS Min Typ Max λc (x-4) (x+1) (x+6) SMSR 30 Pout -3 Transmitter Extinction Ratio Transmitter Eye Opening OMI -- 8.2 10 Transmitter Reflectance Transmitter Jitter RTX Transmitter Center Wavelength Side Mode Suppression Ratio (SMSR) Transmitter Optical Output Power Units Notes/Conditions nm Over temperature -40 to 85 °C case temperature. See Note 1 below dB +2 dBm Average power coupled into single mode fiber dB OC-48 conditions % OC-48 Eye Mask Margin -20 75 dB mUI Parameter per GR-2533 section 5.6 for OC-48 RECEIVER CHARACTERISTICS Optical Input Wavelength Receiver Optical Input Power (BER < 10-9 w/ PRBS 223 - 1) Receiver Optical Input Power (BER < 10-12 w/ PRBS 223 - 1) Receiver Reflectance Dispersion Penalty at 80km λin Pin 1450 -28.0 1620 -7 Pin -26.0 -7 RTX -27 2.5 Table 6. Optical parameters nm dBm 2.5Gb/s w/ PRBS 223-1, measured dBm 2.5Gb/s w/ PRBS 223-1, calculated dB dB See note 4 Note 1: The Transmitter Center Wavelength “x” is as specified by the customer. The current available wavelengths are: 1470, 1490, 1510, 1530, 1550, 1570, 1590, and 1610 nm. Please see the “Product Selection” section on page 2. Note 2: Parameters are specified over temperature and at end of life unless otherwise noted. Note 3: All parameters are measured on a Finisar GBIC Evaluation Card unless otherwise noted. Note 4: Dispersion penalty measured in loop back. Data rate and pattern used same as specified for Optical Input Power. Measured at BER= 10-10. Fiber used is SMF-28. Exact dispersion (ps/nm) will vary depending on wavelength of device under test. © Finisar Corporation December 2004 Rev E Page 5 FTR-1621T-XX WDM GBIC Product Specification – December 2004 Finisar VI. General Specifications Parameter Data Rate Symbol Min BR 0.622 Typ Max 2.7 Units Notes/Conditions Gb/sec Fibre Channel, IEEE 802.3, SONET OC-12/48 Compatible Table 7. General specifications VII. Environmental Specifications Parameter Operating Temp Storage Temp Eye Safety Symbol Top Tsto -- Min -40 -40 Typ Max 85 85 Units Notes/Conditions °C Case temperature °C CDRH and IEC-825 Class 1 Laser Product Note 1 Note 1: Complies with FDA performance standards for laser products except for deviations pursuant to Laser Notice No. 50, dated July 26, 2001. Table 8. Environmental specifications VIII. Serial Communication Protocol All Finisar optical GBICs are ‘Module Definition “4”’ and support the 2 wire serial communication protocol outlined in the GBIC Specification 1. These GBICs use an Atmel AT24C01A 128 byte E2PROM (with an address of 1010000X). For details on interfacing with the E2PROM, see the Atmel data sheet titled “AT24C01A/02/04/08/16 2Wire Serial CMOS E2PROM.”6 All Finisar optical GBICs also incorporate a controller IC that monitors system parameters such as laser current, laser temperature, and, in the case of 13xx/14xx/15xx/16xx nm parts, transmitted power. For a complete description of how to use Finisar’s extended features, see Finisar’s Application Note AN-20305. Parameter Atmel I2C Clock Rate Symbol Catmel Min 0 Finisar Controller I2C Clock Rate C1 10 Typ Max 100,000 100,000 Units Notes/Conditions Hz Bus can be driven blind. Hz Host must support clock stretching. Microcontroller times out if C < 10Hz. Table 9. I2C timing requirements © Finisar Corporation December 2004 Rev E Page 6 FTR-1621T-XX WDM GBIC Product Specification – December 2004 Finisar IX. Mechanical Specifications Finisar WDM GBICs conform to the mechanical specifications outlined in the GBIC Specification Revision 5.5, Section 61. Parameter GBIC insertion GBIC extraction GBIC retention Symbol FI FE FR Min 0 0 130 Typ Max 20 15 N/A Units Newtons Newtons Newtons Notes/Conditions ~4.5 lbs ~3.3 lbs straight out ~29.3 lbs Table 10. Insertion, extraction, and retention forces Figure 1. WDM GBIC outline drawing © Finisar Corporation December 2004 Rev E Page 7 FTR-1621T-XX WDM GBIC Product Specification – December 2004 Finisar X. References 1. “Gigabit Interface Converter (GBIC) Revision 5.5”.(*) Sun Microsystems Computer Company et. al., August 16, 1999. http://playground.sun.com/pub/OEmod/ 2. IEEE Std 802.3. IEEE Standards Department, 2000. 3. “Fibre Channel Physical and Signaling Interface (FC-PH, FC-PH2, FC-PH3)”. American National Standard for Information Systems. 4. “SONET Transport Systems: Common Generic Criteria”, Telcordia Technologies, GR-253-CORE, Issue 3, Sept 2000 5. “Application Note AN-2030: Digital Diagnostic Monitoring Interface for Optical Transceivers”, Finisar Corporation, April 2002. 6. “AT24C01A/02/04/08/16 2-Wire Serial CMOS E2PROM”. Atmel Corporation. www.Atmel.com (*) Neither GBIC, FC-PH, nor IEEE802.3 specifies a 14xx/15xx/16xx nm single mode interface. The FTR-1621T-XX complies with these specifications except for the following optical parameters: laser wavelength, receiver sensitivity, and transmit output power. See Table 6 for details. (**) The FTR-1621T-XX optical interface is not fully SONET/SDH compliant. Please see Table 6. XI. For More Information Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. (408) 548-1000 Fax (408) 541-6138 [email protected] www.finisar.com © Finisar Corporation December 2004 Rev E Page 8