Product Folder Sample & Buy Support & Community Tools & Software Technical Documents Reference Design LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 LP2980-N Micropower 50-mA Ultra Low-Dropout Regulator in SOT-23 Package 1 Features 3 Description • • • • • • • • • • • • • • The LP2980-N is a 50-mA, fixed-output voltage regulator designed specifically to meet the requirements of battery-powered applications. 1 2.1-V to 16-V Input Voltage Range 5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V Output Versions Ultra-Low-Dropout Voltage Output Voltage Accuracy 0.5% (A Grade) Ensured 50-mA Output Current Requires Only 1-μF External Capacitance < 1-μA Quiescent Current When Shutdown Low Ground Pin Current at All Load Currents High Peak Current Capability (150 mA Typical) Wide Supply Voltage Range (16 V Maximum) Fast Dynamic Response to Line and Load Low ZOUT Over Wide Frequency Range Overtemperature and Overcurrent Protection −40°C to 125°C Junction Temperature Range Using an optimized VIP (Vertically Integrated PNP) process, the LP2980-N delivers unequaled performance in all specifications critical to batterypowered designs: Dropout voltage: Typically 120 mV at 50-mA load, and 7 mV at 1-mA load. Ground pin current: Typically 375 μA at 50-mA load, and 80 μA at 1-mA load. Sleep mode: Less than 1-μA quiescent current when ON/OFF pin is pulled low. Minimum part count: Requires only a 1-μF capacitor on the regulator output. Precision output: 0.5% tolerance output voltages available (A grade). 2 Applications • • • • Cellular Phone Palmtop/Laptop Computer Personal Digital Assistant (PDA) Camcorder, Personal Stereo, Camera 5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V versions available as standard products. Device Information(1) PART NUMBER LP2980-N PACKAGE BODY SIZE (NOM) SOT-23 (5) 2.90 mm × 1.60 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Simplified Schematic LP2980 VIN IN VOUT OUT COUT 2.2 µF CIN 1 µF GND ON/OFF ON/OFF NC 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com Table of Contents 1 2 3 4 5 6 7 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 1 1 1 2 3 3 6.1 6.2 6.3 6.4 6.5 6.6 3 4 4 4 4 6 Absolute Maximum Ratings ...................................... ESD Ratings.............................................................. Recommended Operating Conditions....................... Thermal Information .................................................. Electrical Characteristics........................................... Typical Characteristics .............................................. Detailed Description ............................................ 11 7.1 Overview ................................................................. 11 7.2 Functional Block Diagram ....................................... 11 7.3 Feature Description................................................. 11 7.4 Device Functional Modes........................................ 12 8 Application and Implementation ........................ 13 8.1 Application Information............................................ 13 8.2 Typical Application ................................................. 13 9 Power Supply Recommendations...................... 20 10 Layout................................................................... 20 10.1 Layout Guidelines ................................................. 20 10.2 Layout Example .................................................... 20 11 Device and Documentation Support ................. 21 11.1 11.2 11.3 11.4 11.5 Device Support...................................................... Community Resources.......................................... Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 21 21 21 21 21 12 Mechanical, Packaging, and Orderable Information ........................................................... 21 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision N (December 2014) to Revision O Page • Changed pin names VOUT to OUT and VIN to IN per TI nomenclature; correct typos ....................................................... 1 • Changed format of ESD Ratings table .................................................................................................................................. 4 • Changed "1" to "0.5" ............................................................................................................................................................. 11 • Changed Vin to IN (name of pin).......................................................................................................................................... 13 • Changed Vin to IN (name of pin).......................................................................................................................................... 16 • Deleted (the TO-220 package alone will safely dissipate this) - no TO-220 package for this part ...................................... 18 Changes from Revision M (April 2013) to Revision N • Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section; add updated Thermal Information .............................................................................................................................................................. 1 Changes from Revision L (April 2013) to Revision M • 2 Page Page Changed layout of National Data Sheet to TI format ........................................................................................................... 19 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 5 Pin Configuration and Functions SOT-23 (DBV) Package 5 Pins Top View Pin Functions PIN I/O DESCRIPTION NO. NAME 1 IN I Input voltage 2 GND - Common ground (device substrate) 3 ON/OFF I Logic high enable input 4 N/C - DO NOT CONNECT. Device pin 4 is reserved for post packaging test and calibration of the LP2980-N VOUT accuracy. Device pin 4 must be left floating. Do not connect to any potential. Do not connect to ground. Any attempt to do pin continuity testing on device pin 4 is discouraged. Continuity test results will be variable depending on the actions of the factory calibration. Aggressive pin continuity testing (high voltage, or high current) on device pin 4 may activate the trim circuitry forcing VOUT to move out of tolerance. 5 OUT O Regulated output voltage 6 Specifications 6.1 Absolute Maximum Ratings (1) (2) Operating junction temperature MIN MAX UNIT −40 125 °C 260 °C Lead temperature (soldering, 5 seconds) Power dissipation (3) Internally Limited Input supply voltage (survival) −0.3 16 V Input supply voltage (operating) 2.1 16 V Shutdown input voltage (survival) −0.3 16 V Output voltage (survival) (4) −0.3 9 V IOUT (survival) Short-Circuit Protected Input-output voltage (survival) (5) −0.3 16 V Storage temperature –65 150 °C (1) (2) (3) (4) (5) Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Electrical specifications do not apply when operating the device outside of its rated operating conditions. If Military/Aerospace-specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. The maximum allowable power dissipation is a function of the maximum junction temperature, TJ(MAX), the junction-to-ambient thermal resistance, RθJA, and the ambient temperature, TA. The maximum allowable power dissipation at any ambient temperature is calculated using P(MAX) = ( (TJ(MAX) – TA) / RθJA). The value of RθJA for the SOT-23 package is 175.7°C/W. Exceeding the maximum allowable power dissipation will cause excessive die temperature, and the regulator will go into thermal shutdown. If used in a dual-supply system where the regulator load is returned to a negative supply, the LP2980-N output must be diode-clamped to ground. The output PNP structure contains a diode between the IN and OUT pins that is normally reverse-biased. Reversing the polarity from VIN to VOUT will turn on this diode (See Reverse Current Path). Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 3 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com 6.2 ESD Ratings VALUE Electrostatic discharge V(ESD) (1) Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) All pins except 3 and 4 ±2000 Pins 3 and 4 ±1000 UNIT V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions over operating free-air temperature range (unless otherwise noted) MIN MAX UNIT Operating junction temperature −40 125 °C Input supply voltage (operating) 2.1 16 V 6.4 Thermal Information LP2980-N THERMAL METRIC (1) DBV UNIT 5 PINS RθJA Junction-to-ambient thermal resistance RθJC(top) Junction-to-case (top) thermal resistance RθJB Junction-to-board thermal resistance 30.8 ψJT Junction-to-top characterization parameter 2.8 ψJB Junction-to-board characterization parameter 30.3 (1) 175.7 78 °C/W For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. 6.5 Electrical Characteristics Unless otherwise specified: TJ = 25°C, VIN = VO(NOM) + 1 V, IL = 1 mA, COUT = 1 μF, VON/OFF = 2 V. (1) PARAMETER TEST CONDITIONS Output voltage tolerance Output voltage line regulation VIN – VO Dropout voltage (3) MIN TYP MIN −0.5 0.5 −1 1 1 mA < IL < 50 mA −0.75 0.75 −1.5 1.5 1 mA < IL < 50 mA –40°C ≤ TJ ≤ 125°C −2.5 2.5 −3.5 3.5 (2) (3) 4 TYP MAX VO(NOM) + 1 V ≤ VIN ≤ 16 V 0.007 0.014 0.007 0.014 VO(NOM) + 1 V ≤ VIN ≤ 16 V –40°C ≤ TJ ≤ 125°C 0.007 0.032 0.007 0.032 IL = 0 1 3 1 3 IL = 0, –40°C ≤ TJ ≤ 125°C 1 5 1 5 IL = 1 mA 7 10 7 10 7 15 7 15 40 60 40 60 IL = 1 mA, –40°C ≤ TJ ≤ 125°C IL = 10 mA IL = 10 mA, –40°C ≤ TJ ≤ 125°C (1) LP2980I-XX (2) MAX IL = 1 mA ΔVO LP2980AI-XX (2) 40 90 40 90 IL = 50 mA 120 150 120 150 IL = 50 mA, –40°C ≤ TJ ≤ 125°C 120 225 120 225 UNIT %VNOM %/V mV Minimum and maximum limits are ensured through test, design, or statistical correlation over the junction temperature (TJ) range of –40°C to 125°C, unless otherwise stated. Typical values represent the most likely parametric norm at TA = 25°C, and are provided for reference purposes only. Limits are 100% production tested at 25°C. Limits over the operating temperature range are ensured through correlation using Statistical Quality Control (SQC) methods. The limits are used to calculate Average Outgoing Quality Level (AOQL). Dropout voltage is defined as the input to output differential at which the output voltage drops 100 mV below the value measured with a 1-V differential. Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 Electrical Characteristics (continued) Unless otherwise specified: TJ = 25°C, VIN = VO(NOM) + 1 V, IL = 1 mA, COUT = 1 μF, VON/OFF = 2 V.(1) PARAMETER IGND Ground pin current TEST CONDITIONS LP2980AI-XX (2) MIN TYP VON/OFF MAX MIN TYP MAX IL = 0 65 95 65 95 IL = 0, –40°C ≤ TJ ≤ 125°C 65 125 65 125 IL = 1 mA 80 110 80 110 IL = 1 mA, –40°C ≤ TJ ≤ 125°C 80 170 80 170 IL = 10 mA 140 220 140 220 IL = 10 mA, –40°C ≤ TJ ≤ 125°C 140 460 140 460 IL = 50 mA 375 600 375 600 IL = 50 mA, –40°C ≤ TJ ≤ 125°C 375 1200 375 1200 0 1 0 1 VON/OFF < 0.18 V –40°C ≤ TJ ≤ 125°C ON/OFF input voltage (4) LP2980I-XX (2) High = O/P ON –40°C ≤ TJ ≤ 125°C 1.6 1.4 1.6 V Low = O/P OFF –40°C ≤ TJ ≤ 125°C 0.55 0.18 0.55 0.18 VON/OFF = 0 0 −1 0 −1 ON/OFF input current VON/OFF = 5 V –40°C ≤ TJ ≤ 125°C 5 15 5 15 IO(PK) Peak output current VOUT ≥ VO(NOM) − 5% en Output noise voltage (RMS) BW = 300 Hz to 50 kHz COUT = 10 μF Ripple rejection f = 1 kHz COUT = 10 μF Short-circuit current RL = 0 (steady state) (5) (4) (5) μA 1.4 ION/OFF IO(MAX) UNIT 100 150 100 μA 150 mA 160 160 μV 63 63 dB 150 150 mA The ON/OFF inputs must be properly driven to prevent misoperation. For details, see ON/OFF Input Operation. See related curve(s) in Typical Characteristics section. Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 5 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com 6.6 Typical Characteristics Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN. Figure 1. Output Voltage vs Temperature Figure 2. Output Voltage vs Temperature Figure 3. Output Voltage vs Temperature Figure 4. Dropout Characteristics Figure 5. Dropout Characteristics 6 Submit Documentation Feedback Figure 6. Dropout Characteristics Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 Typical Characteristics (continued) Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN. Figure 7. Dropout Voltage vs Temperature Figure 8. Dropout Voltage vs Load Current Figure 9. Ground Pin Current vs Temperature Figure 10. Ground Pin Current vs Load Current Figure 12. Input Current vs VIN Figure 11. Input Current vs VIN Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 7 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com Typical Characteristics (continued) Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN. 8 Figure 13. Line Transient Response Figure 14. Line Transient Response Figure 15. Load Transient Response Figure 16. Load Transient Response Figure 17. Load Transient Response Figure 18. Load Transient Response Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 Typical Characteristics (continued) Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN. Figure 19. Short Circuit Current Figure 20. Instantaneous Short Circuit Current vs Temperature Figure 21. Short Circuit Current Figure 22. Output Impedance vs Frequency Figure 23. Output Impedance vs Frequency Figure 24. Output Noise Density Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 9 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com Typical Characteristics (continued) Unless otherwise specified: TA = 25°C, VIN = VO(NOM) + 1 V, COUT = 2.2 μF, all voltage options, ON/OFF pin tied to VIN. 10 Figure 25. Ripple Rejection Figure 26. Input to Output Leakage vs Temperature Figure 27. Output Reverse Leakage vs Temperature Figure 28. Turn-On Waveform Figure 29. Turn-Off Waveform Figure 30. ON/OFF Pin Current vs VON/OFF Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 7 Detailed Description 7.1 Overview The LP2980-N is a 50-mA, fixed-output voltage regulator designed specifically to meet the requirements of battery-powered applications. Available in output voltages from 2.5 V to 5 V, the device has an output tolerance of % for the A grade (1% for the non-A version). Using an optimized VIP (Vertically Integrated PNP) process, the LP2980-N contains these features to facilitate battery-powered designs: • Fixed 5-V, 4.7-V, 3.3-V, 3-V, and 2.5-V output versions • Very high accuracy 1.23-V reference • Low-dropout voltage, typical dropout of 120 mV at 150-mA load current and 7 mV at 1-mA load • Low ground current, typically 370 μA at 150-mA load and 80 μA at 1-mA load • A sleep mode feature is available, allowing the regulator to consume only 1 µA typically when the ON/OFF pin is pulled low. • Overtemperature protection and overcurrent protection circuitry is designed to safeguard the device during unexpected conditions. 7.2 Functional Block Diagram 7.3 Feature Description 7.3.1 Multiple Voltage Options To meet the different application requirements, the LP2980-N provides multiple fixed output options from 2.5 V to 5 V. 7.3.2 High-Accuracy Output Voltage With special careful design to minimize all contributions to the output voltage error, the LP2980-N distinguishes itself as a very high-accuracy output voltage micropower LDO. This includes a tight initial tolerance (0.5% typical), extremely good line regulation (0.007%/V typical), and a very low output voltage temperature coefficient, making the part an ideal low-power voltage reference. 7.3.3 Ultra-Low-Dropout Voltage Generally speaking, the dropout voltage often refers to the voltage difference between the input and output voltage (VDO = VIN – VOUT), where the main current pass-FET is fully on in the ohmic region of operation and is characterized by the classic RDS(ON) of the FET. VDO indirectly specifies a minimum input voltage above the nominal programmed output voltage at which the output voltage is expected to remain within its accuracy boundary. Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 11 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com Feature Description (continued) 7.3.4 Low Ground Current LP2980-N uses a vertical PNP process which allows for quiescent currents that are considerably lower than those associated with traditional lateral PNP regulators, typically 370 μA at 150-mA load and 80 μA at 1-mA load. 7.3.5 Sleep Mode When pulling the ON/OFF pin to low level, LP2980-N will enter sleep mode, and less than 1-μA quiescent current is consumed. This function is designed for the application which needs a sleep mode to effectively enhance battery life cycle. 7.3.6 Short-Circuit Protection (Current Limit) The internal current-limit circuit is used to protect the LDO against high-load current faults or shorting events. The LDO is not designed to operate in a steady-state current limit. During a current-limit event, the LDO sources constant current. Therefore, the output voltage falls when load impedance decreases. If a current limit occurs and the resulting output voltage is low, excessive power may be dissipated across the LDO resulting in a thermal shutdown of the output. A foldback feature limits the short-circuit current to protect the regulator from damage under all load conditions. If OUT is forced below 0 V before EN goes high and the load current required exceeds the foldback current limit, the device may not start up correctly. 7.3.7 Thermal Protection The LP2980-N contains a thermal shutdown protection circuit to turn off the output current when excessive heat is dissipated in the LDO. The thermal time-constant of the semiconductor die is fairly short, and thus the output cycles on and off at a high rate when thermal shutdown is reached until the power dissipation is reduced. The internal protection circuitry of the LM2980-N is designed to protect against thermal overload conditions. The circuitry is not intended to replace proper heat sinking. Continuously running the device into thermal shutdown degrades its reliability. 7.4 Device Functional Modes 7.4.1 Operation with VOUT(TARGET) + 1 V ≤ VIN < 16 V The device operates if the input voltage is equal to, or exceeds, VOUT(TARGET) + 0.6 V. At input voltages below the minimum VIN requirement, the device does not operate correctly and output voltage may not reach target value. 7.4.2 Operation With ON/OFF Control If the voltage on the ON/OFF pin is less than 0.18 V, the device is disabled, and the shutdown current does not exceed 1 μA. Raising ON/OFF above 1.6 V initiates the start-up sequence of the device. 12 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LP2980-N is a linear voltage regulator operating from 2.1 V to 16 V on the input and regulates voltages between 2.5 V to 5 V with 0.5% accuracy and 50-mA maximum output current. Efficiency is defined by the ratio of output voltage to input voltage because the LP2980-N is a linear voltage regulator. To achieve high efficiency, the dropout voltage (VIN – VOUT) must be as small as possible, thus requiring a very-low-dropout LDO. Successfully implementing an LDO in an application depends on the application requirements. If the requirements are simply input voltage and output voltage, compliance specifications (such as internal power dissipation or stability) must be verified to ensure a solid design. If timing, startup, noise, power supply rejection ratio (PSRR), or any other transient specification is required, then the design becomes more challenging. This section discusses the implementation and behavior of the LP2980-N LDO. 8.2 Typical Application *ON/OFF input must be actively terminated. Tie to if this function is not to be used. **Minimum output capacitance is 1 μF to ensure stability over full load current range. More capacitance provides superior dynamic performance and additional stability margin (see Output Capacitor Recommendation). ***Do not make connections to this pin. 8.2.1 Design Requirements PARAMETER DESIGN REQUIREMENT Input voltage 5 V ±10%, provided by the DC-DC converter switching at 1 MHz Output voltage 3.3 V ±5% Output current 50 mA (maximum), 1 mA (minimum) RMS noise, 300 Hz to 50 kHz < 1 mVRMS PSRR at 1 kHz > 40 dB Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 13 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com 8.2.2 Detailed Design Procedure At 50-mA loading, the dropout of the LP2980-N has 225-mV maximum dropout over temperature, thus an 1700mV headroom is sufficient for operation over both input and output voltage accuracy. The efficiency of the LP2980-N in this configuration is VOUT / VIN = 66.7%. To achieve the smallest form factor, the SOT-23 package is selected. Input and output capacitors are selected in accordance with the Output Capacitor Recommendation section. With an efficiency of 66.7% and a 50-mA maximum load, the internal power dissipation is 85 mW, which corresponds to a 14.9°C junction temperature rise for the SOT-23 package. With an 85°C maximum ambient temperature, the junction temperature is at 99.9°C. 8.2.2.1 Output Capacitor Recommendation Like any low-dropout regulator, the LP2980-N requires an output capacitor to maintain regulator loop stability. This capacitor must be selected to meet the requirements of minimum capacitance and equivalent series resistance (ESR) range. It is not difficult to find capacitors which meet the criteria of the LP2980-N, as the acceptable capacitance and ESR ranges are wider than for most other LDOs. In general, the capacitor value must be at least 1 μF (over the actual ambient operating temperature), and the ESR must be within the range indicated in Figure 31, Figure 32, and Figure 33. It should be noted that, although a maximum ESR is shown in these figures, it is very unlikely to find a capacitor with an ESR that high. 8.2.2.1.1 Tantalum Capacitors Surface-mountable solid tantalum capacitors offer a good combination of small physical size for the capacitance value, and an ESR in the range needed by the LP2980-N. The results of testing the LP2980-N stability with surface-mount solid tantalum capacitors show good stability with values of at least 1 μF. The value can be increased to 2.2 μF (or more) for even better performance, including transient response and noise. Small value tantalum capacitors that have been verified as suitable for use with the LP2980-N are shown in Table 1. Capacitance values can be increased without limit. 8.2.2.1.2 Aluminum Electrolytic Capacitors Although probably not a good choice for a production design, because of relatively large physical size, an aluminum electrolytic capacitor can be used in the design prototype for an LP2980-N regulator. A value of at least 1 μF should be used, and the ESR must meet the conditions of Figure 31, Figure 32, and Figure 33. If the operating temperature drops below 0°C, the regulator may not remain stable, as the ESR of the aluminum electrolytic capacitor will increase and may exceed the limits indicated in Figure 31, Figure 32, and Figure 33. Table 1. Surface-Mount Tantalum Capacitor Selection Guide 1-μF SURFACE-MOUNT TANTALUM CAPACITORS MANUFACTURER PART NUMBER Kemet T491A105M010AS NEC NRU105M10 Siemens B45196-E3105-K Nichicon F931C105MA Sprague 293D105X0016A2T 2.2-μF SURFACE-MOUNT TANTALUM CAPACITORS 14 MANUFACTURER PART NUMBER Kemet T491A225M010AS NEC NRU225M06 Siemens B45196/2.2/10/10 Nichicon F930J225MA Sprague 293D225X0010A2T Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 8.2.2.1.3 Multilayer Ceramic Capacitors Surface-mountable multilayer ceramic capacitors may be an attractive choice because of their relatively small physical size and excellent RF characteristics. However, they sometimes have ESR values lower than the minimum required by the LP2980-N, and relatively large capacitance change with temperature. The manufacturer's data sheet for the capacitor should be consulted before selecting a value. Test results of LP2980-N stability using multilayer ceramic capacitors show that a minimum value of 2.2 μF is usually needed for the 5-V regulator. For the lower output voltages, or for better performance, a higher value should be used, such as 4.7 μF. Multilayer ceramic capacitors that have been verified as suitable for use with the LP2980-N are shown in Table 2. Table 2. Surface-Mount Multilayer Ceramic Capacitor Selection Guide 2.2-μF SURFACE-MOUNT CERAMIC MANUFACTURER PART NUMBER Tokin 1E225ZY5U-C203 Murata GRM42-6Y5V225Z16 4.7-μF SURFACE-MOUNT CERAMIC MANUFACTURER PART NUMBER Tokin 1E475ZY5U-C304 Figure 31. 1-μF ESR Range Figure 32. 2.2-μF ESR Range Figure 33. 10-μF ESR Range Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 15 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com 8.2.2.2 Reverse Current Path The internal PNP power transistor used as the pass element in the LP2980-N has an inherent diode connected between the regulator output and input. During normal operation (where the input voltage is higher than the output) this diode is reverse biased (see Figure 34). VIN VOUT PNP GND Figure 34. LP2980-N Reverse Current Path However, if the input voltage is more than a VBE below the output voltage, this diode will turn on and current will flow into the regulator output. In such cases, a parasitic SCR can latch which will allow a high current to flow into the VIN pin and out the ground pin, which can damage the part. The internal diode can also be turned on if the input voltage is abruptly stepped down to a voltage which is a VBE below the output voltage. In any application where the output voltage may be higher than the input voltage, an external Schottky diode must be connected from VIN to VOUT (cathode on VIN, anode on VOUT, see Figure 35), to limit the reverse voltage across the LP2980-N to 0.3 V (see Absolute Maximum Ratings). SCHOTTKY DIODE VIN VOUT PNP GND Figure 35. Adding External Schottky Diode Protection 8.2.2.3 ON/OFF Input Operation The LP2980-N is shut off by pulling the ON/OFF input low, and turned on by driving the input high. If this feature is not to be used, the ON/OFF input should be tied to IN to keep the regulator on at all times (the ON/OFF input must not be left floating). To ensure proper operation, the signal source used to drive the ON/OFF input must be able to swing above and below the specified turn-on and turn-off voltage thresholds which ensure an ON or OFF state (see Electrical Characteristics). The ON/OFF signal may come from either a totem-pole output, or an open-collector output with a pull-up resistor to the LP2980-N input voltage or another logic supply. The high-level voltage may exceed the LP2980-N input voltage, but must remain within the absolute maximum ratings for the ON/OFF pin. 16 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 It is also important that the turn-on and turn-off voltage signals applied to the ON/OFF input have a slew rate that is greater than 40 mV/μs. NOTE The regulator shutdown function will not operate correctly if a slow-moving signal is used to drive the ON/OFF input. 8.2.2.4 Increasing Output Current The LP2980-N can be used to control higher-current regulators, by adding an external PNP pass transistor. With the PNP transistors shown in Figure 36, the output current can be as high as 400 mA, as long as the input voltage is held within the Safe Operation Boundary Curves shown below in Figure 37. To ensure regulation, the minimum input voltage of this regulator is 6 V. This headroom is the sum of the VBE of the external transistor and the dropout voltage of the LP2980-N. Figure 36. 5-V and 400-mA Regulator Notes: Note A: Drive this input with a logic signal (see ON/OFF Input Operation). If the shutdown function is not to be used, tie the ON/OFF pin directly to the IN pin. Note B: Recommended devices (other PNP transistors can be used if the current gain and voltage ratings are similar). Note C: Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit. Note D: Increasing the output capacitance improves transient response and increases phase margin. Note E: Maximum safe input voltage and load current are limited by power dissipation in the PNP pass transistor and the maximum ambient temperature for the specific application. If a TO-92 transistor such as the MPS2907A is used, the thermal resistance from junction-to-ambient is 180°C/W in still air. Assuming a maximum allowable junction temperature of 150°C for the MPS2907A device, the following curves show the maximum VIN and IL values that may be safely used for several ambient temperatures. Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 17 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com Figure 37. Safe Operation Boundary Curves for Figure 36 With limited input voltage range, the LP2980-N can control a 3.3-V, 3-A regulator with the use of a high currentgain external PNP pass transistor as shown in Figure 38. If the regulator is to be loaded with the full 3 A, heat sinking will be required on the pass transistor to keep it within its rated temperature range. See Figure 39. For best load regulation at the high load current, the LP2980-N output voltage connection should be made as close to the load as possible. Although this regulator can handle a much higher load current than can the LP2980-N alone, it can be shut down in the same manner as the LP2980-N. When the ON/OFF control is brought low, the converter will be in shutdown, and will draw less than 1 μA from the source. Figure 38. 5 V to 3.3 V at 3-A Converter NOTES: Note A: Drive this input with a logic signal (see ON/OFF Input Operation). If the shutdown function is not to be used, tie the ON/OFF pin directly to the IN pin. Note B: Capacitor is required for regulator stability. Minimum size is shown, and may be increased without limit. Note C: Increasing the output capacitance improves transient response and increases phase margin. Note D: A heatsink may be required for this transistor. The maximum allowable value for thermal resistance of the heatsink is dependent on ambient temperature and load current (see curves in Figure 39). Once the value is obtained from the graph, a heatsink must be selected which has a thermal resistance equal to or lower than this value. If the value is above 60°C/W, no heatsink is required. 18 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 For these curves, a maximum junction temperature of 150°C is assumed for the pass transistor. The case-toheatsink attachment thermal resistance is assumed to be 1.5°C/W. All calculations are for 5.5-V input voltage (which is worst-case for power dissipation). Figure 39. Heatsink Thermal Resistance Requirements for Figure 38 8.2.3 Application Curve Figure 40. Load Transient Response Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 19 LP2980-N SNOS733O – APRIL 2000 – REVISED JUNE 2015 www.ti.com 9 Power Supply Recommendations The LP2980-N is designed to operate from an input voltage supply range between 2.1 V and 16 V. The input voltage range provides adequate headroom for the device to have a regulated output. This input supply must be well regulated. If the input supply is noisy, additional input capacitors with low ESR can help improve the output noise performance. 10 Layout 10.1 Layout Guidelines For best overall performance, place all circuit components on the same side of the circuit board and as near as practical to the respective LDO pin connections. Place ground return connections to the input and output capacitors, and to the LDO ground pin as close to each other as possible, connected by a wide, component-side, copper surface. The use of vias and long traces to create LDO circuit connections is strongly discouraged and negatively affects system performance. This grounding and layout scheme minimizes inductive parasitics, and thereby reduces load-current transients, minimizes noise, and increases circuit stability. A ground reference plane is also recommended and is either embedded in the PCB itself or located on the bottom side of the PCB opposite the components. This reference plane serves to assure accuracy of the output voltage, shield noise, and behaves similar to a thermal plane to spread (or sink) heat from the LDO device. In most applications, this ground plane is necessary to meet thermal requirements. 10.2 Layout Example VIN VOUT Input Capacitor IN GND OUT Output Capacitor Ground ON/OFF ON/OFF NC Figure 41. LP2980-N Layout Example 20 Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N LP2980-N www.ti.com SNOS733O – APRIL 2000 – REVISED JUNE 2015 11 Device and Documentation Support 11.1 Device Support 11.1.1 Third-Party Products Disclaimer TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE. 11.2 Community Resources The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.3 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.4 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.5 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Submit Documentation Feedback Copyright © 2000–2015, Texas Instruments Incorporated Product Folder Links: LP2980-N 21 PACKAGE OPTION ADDENDUM www.ti.com 9-Aug-2016 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LP2980AIM5-2.5 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L0NA LP2980AIM5-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0NA LP2980AIM5-3.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L02A LP2980AIM5-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L02A LP2980AIM5-3.3 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L00A LP2980AIM5-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L00A LP2980AIM5-4.7/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L37A LP2980AIM5-5.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L01A LP2980AIM5-5.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L01A LP2980AIM5X-2.5 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L0NA LP2980AIM5X-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0NA LP2980AIM5X-3.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L02A LP2980AIM5X-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L02A LP2980AIM5X-3.3 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L00A LP2980AIM5X-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L00A LP2980AIM5X-4.7 NRND SOT-23 DBV 5 TBD Call TI Call TI -40 to 125 L37A LP2980AIM5X-4.7/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L37A LP2980AIM5X-5.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L01A LP2980AIM5X-5.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L01A LP2980IM5-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0NB LP2980IM5-3.0 NRND SOT-23 DBV 5 TBD Call TI Call TI -40 to 125 L02B Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com Orderable Device 9-Aug-2016 Status (1) LP2980IM5-3.0/NOPB Package Type Package Pins Package Drawing Qty ACTIVE SOT-23 DBV 5 1000 Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L02B (4/5) LP2980IM5-3.3 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L00B LP2980IM5-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L00B LP2980IM5-3.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L21B LP2980IM5-4.7/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L37B LP2980IM5-5.0 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 L01B LP2980IM5-5.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L01B LP2980IM5X-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L0NB LP2980IM5X-3.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L02B LP2980IM5X-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L02B LP2980IM5X-3.3 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L00B LP2980IM5X-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L00B LP2980IM5X-5.0 NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 L01B LP2980IM5X-5.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 L01B (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com 9-Aug-2016 Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ B0 (mm) K0 (mm) P1 (mm) LP2980AIM5-2.5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5-2.5/NOPB SOT-23 DBV 5 1000 178.0 LP2980AIM5-3.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 LP2980AIM5-3.0/NOPB SOT-23 DBV 5 1000 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 LP2980AIM5-3.3 SOT-23 DBV 5 Q3 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5-3.3/NOPB SOT-23 DBV LP2980AIM5-4.7/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 LP2980AIM5-5.0 SOT-23 Q3 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5-5.0/NOPB LP2980AIM5X-2.5 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-4.7/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-5.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980AIM5X-3.0 LP2980AIM5X-3.3 LP2980AIM5X-5.0 Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) Pack Materials-Page 1 W Pin1 (mm) Quadrant PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LP2980IM5-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 LP2980IM5-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5-3.3 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5-3.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5-4.7/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5-5.0 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5-5.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-3.0 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-3.3 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-5.0 SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LP2980IM5X-5.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2980AIM5-2.5 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 10-Aug-2016 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LP2980AIM5-3.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-3.3 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-4.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-5.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5-5.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980AIM5X-2.5 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-3.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-3.3 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-4.7/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-5.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980AIM5X-5.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-3.3 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-3.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-4.7/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-5.0 SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5-5.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LP2980IM5X-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-3.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-3.3 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-5.0 SOT-23 DBV 5 3000 210.0 185.0 35.0 LP2980IM5X-5.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2016, Texas Instruments Incorporated