HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz Typical Applications Features The HMC600LP4 / HMC600LP4E is ideal for IF and RF applications in: Wide Dynamic Range: up to 75 dB • Cellular/PCS/3G Power-Down Mode • WiMAX, WiBro & Fixed Wireless Excellent Stability over Temperature • Power Monitoring & Control Circuitry Compact 4x4mm Leadless SMT Package Flexible Supply Voltage: +2.7V to +5.5V • Receiver Signal Strength Indication (RSSI) • Automatic Gain & Power Control General Description Functional Diagram The HMC600LP4 & HMC600LP4E Logarithmic Detector/Controller convert RF signals at its input, to a proportional DC voltage at its output. The HMC600LP4 & HMC600LP4E employ a successive compression topology which delivers extremely high dynamic range and conversion accuracy over a wide input frequency range. As the input power is increased, successive amplifiers move into saturation one by one creating an accurate approximation of the logarithm function. The output of a series of square law detectors is summed, converted into voltage domain and buffered to drive the LOGOUT output. For detection mode, the LOGOUT pin is shorted to the VSET input, and will provide a nominal logarithmic slope of 19mV/dB and an intercept of -95 dBm. The HMC600LP4 & HMC600LP4E can also be used in the controller mode where an external voltage is applied to the VSET pin, to create an AGC or APC feedback loop. POWER DETECTORS - SMT 10 Electrical Specifications, TA = +25C, PWD = 0V, Vcc1, Vcc2 = +3.3V [1] Typ. Typ. Typ. Typ. Typ. Typ. Typ. Typ. Units Input Frequency Parameter 50 100 500 900 1900 2500 3500 4000 MHz ±3 dB Dynamic Range 74 74 74 74 70 66 51 48 dB ±3 dB Dynamic Range Center -30 -30 -30 -30.5 -31.0 -31.0 -27 -23.5 dBm ±1 dB Dynamic Range 64 64 64 65 62 59 44 41 dB 19.6 19.5 19.4 19.2 19.1 19.5 21.0 22.3 mV/dB Output Slope Output Intercept -96 -96 -96 -96 -95 -93 -79 -72 dBm Temperature Sensitivity @ -10 dBm Input [2] -2.7 -2.8 -3.6 -4.8 -6.9 -7.4 -8.3 -12.9 mdB/°C [1] Detector mode measurements; LOGOUT (Pin 17) is shorted to VSET (Pin 16). [2] Measured from TA = -40C to TA = +85C 10 - 2 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz Electrical Specifications, (continued) Parameter Conditions Min. Typ. Max. Units RF Input (INP) Return Loss F = 50 - 4000 MHz, Zo = 50Ω, See plot 10 dB 16 kΩ LOGOUT Interface Current Drive (Source) Current Drive (Sink) For 1% change in the output voltage Output Voltage Range 0.4 mA 2.25 mA 0 Small Signal Response Time (10% to 90%) Large Signal Response Time (±0.5 dB Settling) Output Rise Time Ripple Vcc -0.13 V Pin = -60 to -57 dBm 50 ns Pin = No Signal to 0 dBm 150 ns From 0% to 90% 90 ns Fin = 100 MHz <2 mVpp 30 kΩ VSET Interface Input Impedance Input Voltage Range Low Frequency Gain VSET to LOGOUT Open Loop Corner Frequency 0.6 to 1.9 V 78 dB 1.6 kHz Power Down (PWD) Interface Voltage Range for Normal Mode Voltage Range for Shutdown Mode 0 0.2 x Vcc 0.8 x Vcc Vcc Threshold Voltage Power-up Response Time Vcc/2 V V V 50% PWD to ±0.5 dB Settling of LOGOUT 3.8 μs 50% PWD to 10% Icc 6.6 μs Power-Down Response Time Power Supply (Vcc1, Vcc2) Operating Voltage Range 2.7 Supply Current in Normal Mode Vcc = +3.3V, PWD = 0V 29 Supply Current in Power Down Mode Vcc = +3.3V, PWD = Vcc 1 5.5 V 36 mA Test Conditions Parameter Condition Vcc1, Vcc2 +3.3V Input Zo 50Ω TA +25C Fin 900 MHz mA 10 POWER DETECTORS - SMT Open Loop Impedance INN Port connected to ground through a 1000pF capacitor For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 3 HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 50 MHz 5 2 4 1.8 3 1.6 2 1.4 Ideal LOGOUT +25 C LOGOUT +85 C LOGOUT -40 C 1 1 0 0.8 -1 0.6 0 0.8 0.4 0.2 -4 0.2 0 -5 0 -60 -50 -40 -30 -20 -10 0 -1 -2 -70 -60 -50 3 1.6 1.4 2 1.4 1.2 1 1 0 LOGOUT (V) LOGOUT (V) 1.8 0.6 -3 0.4 -4 0.2 -5 0 ERR +25 C ERR +85 C ERR -40 C 0 -40 -30 -20 -10 0 5 -60 2 4 1.8 3 1.6 2 1.4 Ideal LOGOUT +25 C LOGOUT +85 C LOGOUT -40 C LOGOUT (V) 1 0 0.6 -3 0.4 -4 0.2 -5 0 ERR +25 C ERR +85 C ERR -40 C -20 -10 0 INPUT POWER (dBm) -5 5 4 Ideal LOGOUT +25 C LOGOUT +85 C LOGOUT -40 C 3 2 0.8 -1 -2 -3 ERR +25 C ERR +85 C ERR -40 C -70 -60 -50 -40 -30 -20 -10 INPUT POWER (dBm) Unless otherwise noted: Vcc1, Vcc2 = +3.3V, TA = +25C 10 - 4 0 0 -2 -30 -10 1 0.6 -40 -20 1 -1 -50 -30 1.2 0.8 -60 -40 -4 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com -4 0 -5 ERROR (dB) 1 ERROR (dB) 1.2 LOGOUT (V) 5 0 -70 -50 -3 LOGOUT Voltage & Error vs. Input Power, Fin = 2500 MHz 2 0.2 -2 ERR +25 C ERR +85 C ERR -40 C INPUT POWER (dBm) 1.8 0.4 2 -1 -70 LOGOUT Voltage & Error vs. Input Power, Fin = 1900 MHz 1.4 3 0.8 INPUT POWER (dBm) 1.6 4 Ideal LOGOUT +25 C LOGOUT +85 C LOGOUT -40 C 0 -2 -50 -5 1 0.6 -60 0 1 -1 -70 -10 1.2 0.8 0.2 -20 ERROR (dB) 2 4 ERROR (dB) 5 Ideal LOGOUT +25 C LOGOUT +85 C LOGOUT -40 C 0.4 -30 LOGOUT Voltage & Error vs. Input Power, Fin = 900 MHz 2 1.6 -40 -4 INPUT POWER (dBm) LOGOUT Voltage & Error vs. Input Power, Fin = 500 MHz 1.8 -3 ERR +25 C ERR +85 C ERR -40 C INPUT POWER (dBm) 10 2 1 -3 -70 3 1 0.6 0.4 4 Ideal LOGOUT +25 C LOGOUT +85 C LOGOUT -40 C 1.2 -2 ERR +25 C ERR +85 C ERR -40 C 5 ERROR (dB) 1.2 ERROR (dB) LOGOUT (V) 1.4 LOGOUT (V) 2 1.8 1.6 POWER DETECTORS - SMT LOGOUT Voltage & Error vs. Input Power, Fin = 100 MHz HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz LOGOUT Voltage & Error vs. Input Power, Fin = 4000 MHz Ideal LOGOUT +25 C LOGOUT +85 C LOGOUT -40 C 1.6 2 4 1.8 3 1.6 2 1.4 1 1 0 0 -2 0.6 -3 0.4 -4 0.2 -5 0 0 -60 -50 -40 -30 -20 -10 0 0.8 -1 -2 -60 -50 24 24 +25 C +85 C -40 C SLOPE (mV/dB) SLOPE (mV/dB) 25 21 19 18 2000 2500 3000 3500 18 2.5 4000 3 3.5 FREQUENCY (MHz) 10 4 4.5 5 5.5 LOGOUT Intercept vs. Bias Voltage TA = +25C -50 -50 -60 -60 INTERCEPT (dBm) INTERCEPT (dBm) -5 Vcc (V) LOGOUT Intercept vs. Frequency, Vcc = +3.3V +25 C +85 C -40 C -70 0 21 19 1500 -10 22 20 1000 -20 50 MHz 900 MHz 1900 MHz 3500 MHz 4000 MHz 23 20 500 -30 LOGOUT Slope vs. Supply Voltage, TA = +25C 25 0 -40 -4 INPUT POWER (dBm) LOGOUT Slope vs. Frequency, Vcc = 3.3V 22 -3 ERR +25 C ERR +85 C ERR -40 C INPUT POWER (dBm) 23 2 1 0.6 0.2 3 1 -1 ERR +25 C ERR +85 C ERR -40 C 4 Ideal LOGOUT +25 C LOGOUT +85 C LOGOUT -40 C 1.2 0.8 0.4 5 -80 -90 ERROR (dB) 1.2 ERROR (dB) LOGOUT (V) 1.4 5 LOGOUT (V) 2 1.8 50 MHz 900 MHz 1900 MHz 3500 MHz 4000 MHz POWER DETECTORS - SMT LOGOUT Voltage & Error vs. Input Power, Fin = 3500 MHz -70 -80 -90 -100 0 500 1000 1500 2000 2500 3000 3500 4000 FREQUENCY (MHz) -100 2.5 3 3.5 4 4.5 5 5.5 Vcc (V) Unless otherwise noted: Vcc1, Vcc2 = +3.3V, TA = +25C For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 5 HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz LOGOUT Error vs. Input Power, Normalized[2], Fin = 1900 MHz Input Return Loss 0 2.5 INPUT RETURN LOSS (dB) NORMALIZED ERROR (dB) 2 +85 C -40 C 1.5 1 0.5 0 -0.5 -1 -15 -20 +25 C +85 C -40 C -25 -35 -60 -50 -40 -30 -20 -10 0 0 1 INPUT POWER (dBm) 10 50 MHz 900 MHz 1900 MHz 3500 MHz 4000 MHz 1.6 1.4 1.2 1 0.8 0.6 0.4 -75 -65 -55 -45 -35 -25 INPUT POWER (dBm) 3 4 -15 -5 5 Vcc1, Vcc2 0V to +5.5V PWD 0V to +5.5V VSET Input Voltage 0V to +5.5V LOGOUT Output Current 3 mA RF Input Power +12 dBm Junction Temperature 125 °C Continuous Pdiss (T = 85°C) (Derate 7.95 mW/°C above 85°C) 0.32 Watts Thermal Resistance (Rth) (junction to lead) 126 °C/W Storage Temperature -65 to +150 °C Operating Temperature -40 to +85 °C ESD Sensitivity (HBM) Class 1C ELECTROSTATIC SENSITIVE DEVICE OBSERVE HANDLING PRECAUTIONS [1] Unless otherwise noted: Vcc1, Vcc2 = +3.3V, TA = +25C [2] This data is relative to the room temperature performance of the HMC600LP4 10 - 6 5 Absolute Maximum Ratings 2 1.8 2 FREQUENCY (GHz) LOGOUT Voltage vs. Input Power and Frequency, TA = +25C LOGOUT (V) POWER DETECTORS - SMT -10 -30 -1.5 -2 -70 -5 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz Outline Drawing NOTES: 1. LEADFRAME MATERIAL: COPPER ALLOY 2. DIMENSIONS ARE IN INCHES [MILLIMETERS]. 3. LEAD SPACING TOLERANCE IS NON-CUMULATIVE 4. PAD BURR LENGTH SHALL BE 0.15mm MAXIMUM. PAD BURR HEIGHT SHALL BE 0.05mm MAXIMUM. 5. PACKAGE WARP SHALL NOT EXCEED 0.05mm. 6. ALL GROUND LEADS AND GROUND PADDLE MUST BE SOLDERED TO PCB RF GROUND. 7. REFER TO HITTITE APPLICATION NOTE FOR SUGGESTED PCB LAND PATTERN. Package Information Part Number Package Body Material Lead Finish MSL Rating HMC600LP4 Low Stress Injection Molded Plastic Sn/Pb Solder MSL1 HMC600LP4E RoHS-compliant Low Stress Injection Molded Plastic 100% matte Sn MSL1 Package Marking [3] [1] H600 XXXX [2] H600 XXXX POWER DETECTORS - SMT 10 [1] Max peak reflow temperature of 235 °C [2] Max peak reflow temperature of 260 °C [3] 4-Digit lot number XXXX For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 7 HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz Pin Descriptions Pin Number Function Description 1, 6, 7-13, 15, 18-24 N/C These pins are not connected internally; however, this product is specified with these pins connected to RF/DC ground. 2, 6 Vcc1, Vcc2 Bias supply. Connect supply voltage to both pins. 3, 4 INP, INN RF Input pins. Connect RF to INP, and AC couple INN to ground for single-ended operation. 14 PWD Connect to 0V for normal operation. Applying voltage >0.8 x Vcc will initiate a power saving shutdown mode. 16 VSET VSET input in controller mode. Short this pin to LOGOUT for detector mode. 17 LOGOUT Logarithmic output that converts the input power to a DC level in detector mode. Short this pin to VSET for detector mode. Package Base GND Exposed paddle must be connected to RF and DC ground. Interface Schematic POWER DETECTORS - SMT 10 10 - 8 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz Evaluation PCB List of Materials for Evaluation PCB 115242 [1] Item Description J1 - J4 PC Mount SMA Connector J5 - J8 DC Pin C1, C2 1000 pF Capacitor, 0402 Pkg. C3, C4 0.1μF Capacitor, 0402 Pkg. R1, R2 5.6Ω Resistor, 0603 Pkg. R3-R5 0Ω Resistor, 0603 Pkg. U1 HMC600LP4 / HMC600LP4E Logarithmic Detector / Controller PCB [2] 115244 Eval Board The circuit board used in the final application should use RF circuit design techniques. Signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. A sufficient number of via holes should be used to connect the top and bottom ground planes. The evaluation circuit board shown is available from Hittite upon request. POWER DETECTORS - SMT 10 [1] Reference this number when ordering complete evaluation PCB [2] Circuit Board Material: Rogers 4350 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 9 HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz Application & Evaluation PCB Schematic POWER DETECTORS - SMT 10 10 - 10 Notes Note 1: The HMC600LP4 & HMC600LP4E evaluation boards are pre-assembled for single-ended input, and detector/RSSI mode. Note 2: For single-ended input operation, use the INP port and make no connection to INN. INN is AC coupled to ground by C2 Note 3: For differential input, remove C2, and install a 1000pF capacitor in series with INN at location shown. Note 4: For detector mode, connect high impedence volt meter to the LOGOUT port, and make no connection to VSET. LOGOUT is shorted to VSET by R3, as required for detector mode. Note 5: For controller mode, remove R3 and make appropriate connection to LOGOUT and VSET. In controller mode, the LOGOUT output can be used to drive a variable gain amplifier, or a variable attenuator, either directly or through a buffer or microcontroller. VSET should be connected to an external supply, typically between +0.6 and +1.9V. For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com HMC600LP4 / 600LP4E v01.0606 75 dB LOGARITHMIC DETECTOR / CONTROLLER 50 - 4000 MHz Notes: POWER DETECTORS - SMT 10 For price, delivery, and to place orders, please contact Hittite Microwave Corporation: 20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373 Order On-line at www.hittite.com 10 - 11