FS2A THRU FS2M SURFACE MOUNT FAST RECOVERY RECTIFIER Reverse Voltage - 50 to 1000 Volts DO-214AC (HSMA) (High Profile) FEATURES The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 For surface mounted applications Low reverse leakage Built-in strain relief,ideal for automated placement High forward surge current capability High temperature soldering guaranteed: 250 C/10 seconds at terminals Glass passivated chip junction H Cathode Band J A E C D B F MECHANICAL DATA G DIMENSIONS DIM A B C D E F G H J INCHES MIN .078 .067 .002 --.035 .065 .205 .160 .100 Forward Current - 2.0 Ampere MAX .116 .089 .008 .02 .055 .096 .224 .180 .112 MM MIN 1.98 1.70 .05 --.89 1.65 5.21 4.06 2.57 MAX 2.95 2.25 .20 .51 1.40 2.45 5.69 4.57 2.84 Case : JEDEC DO-214AC molded plastic body over passivated chip Terminals : Solder plated, solderable per MIL-STD-750, Method 2026 Polarity : Color band denotes cathode end Mounting Position : Any Weight :0.002 ounce, 0.07 grams NOTE MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. MDD Catalog Number Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current at TL=90 C Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 2.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Maximum reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range SYMBOLS VRRM VRMS VDC FS2A FS2B 50 35 50 FS2D 100 70 100 200 140 200 FS2G FS2J FS2K FS2M UNITS 400 280 400 800 560 800 1000 700 1000 VOLTS VOLTS VOLTS 600 420 600 I(AV) 2.0 Amp IFSM 50.0 Amps VF 1.3 Volts IR 5.0 50.0 µA trr CJ RθJA TJ,TSTG Note:1.Reverse recovery condition IF=0.5A,IR=1.0A,Irr=0.25A 2.Measured at 1MHz and applied reverse voltage of 4.0V D.C. 3.P.C.B. mounted with 0.2x0.2”(5.0x5.0mm) copper pad areas 150 250 50.0 15.0 -50 to +150 500 ns pF C/W C RATINGS AND CHARACTERISTIC CURVES FS2A THRU FS2M Figure 1 Typical Forward Characteristics 20 Figure 2 Forward Derating Curve 10 3.0 6 4 2.5 2 25°C Amps 2.0 1 .6 1.5 Amps .4 1.0 .2 .5 .1 Single Phase, Half Wave 60Hz Resistive or Inductive Load .06 0 .04 0 50 75 100 125 150 175 °C .02 .01 .4 .6 .8 1.0 1.2 Average Forward Rectified Current - Amperesversus Ambient Temperature -°C 1.4 Volts Instantaneous Forward Current - Amperesversus Instantaneous Forward Voltage - Volts Figure 3 Junction Capacitance 100 60 40 20 pF TJ=25°C 10 6 4 2 1 .1 .2 .4 1 Volts 2 4 10 20 40 100 200 Junction Capacitance - pFversus Reverse Voltage - Volts The cruve graph is for reference only, can't be the basis for judgment(曲线图仅供参考)! 400 1000 RATINGS AND CHARACTERISTIC CURVES FS2A THRU FS2M Figure 4 Maximum Non-Repetitive Forward Surge Current 90 75 60 45 Amps 30 15 0 1 2 4 6 8 10 20 40 60 80 100 Cycles Peak Forward Surge Current - Amperesversus Number Of Cycles At 60Hz - Cycles Figure 5 Reverse Recovery Time Characteristic And Test Circuit Diagram 50Ω 10Ω trr +0.5A 0 Pulse Generator Note 2 25Vdc 1Ω Oscilloscope Note 1 -0.25 -1.0 Notes: 1. Rise Time = 7ns max. Input impedance = 1 megohm, 22pF 2. Rise Time = 10ns max. Source impedance = 50 ohms 3. Resistors are non-inductive The cruve graph is for reference only, can't be the basis for judgment(曲线图仅供参考)! 1cm Set Time Base for 20/100ns/cm