Type HZA -55 ºC to +105 ºC SMT Hybrid Polymer-Aluminum Electrolytic Capacitors For filtering, Bypassing and Power Supply Decoupling with Long Life Requirements Rated for 105°C, type HZA combines the advantages of aluminum electrolytic and aluminum polymer technology. These hybrid capacitors have the ultra-low ESR characteristics of conductive aluminum polymer capacitors packaged in a V-chip, SMT case with high capacitance and voltage ratings Highlights +105 °C, Up to 10,000 Hours Load Life Low Leakage Current Very Low ESR and High Ripple Current 260 °C reflow soldering AEC-Q200 Compliant Film - Specifications Capacitance Range 10 to 330 µF Capacitance Tolerance ±20% @ 120 Hz/+20 °C Rated Voltage 25, 35, 50, 63, 80 Vdc Leakage Current (at 20°C) I = .01CV or 3 µA max., whichever is greater after 2 minutes I = leakage current in µAmps C = rated capacitance in µF V = rated DC Working voltage in Volts Low Temperature Characteristics (at 120 Hz) Z(-25 ºC)/Z(+20 ºC): 2 Z(-55 ºC)/Z(+20 ºC): 2.5 Ripple Current Frequency Multiplier Frequency Correction Factor 120 Hz 1000 Hz 10,000 Hz 100 KHz 0.1 0.3 0.6 1 RoHS Compliant Outline Drawing mm Case Code D L A B (± 0.5) ( ± 0.3) (± 0.2) ( ± 0.2) H (max.) I (ref.) W P (ref.) K C 5.0 5.8 5.3 5.3 6.5 2.2 0.65 ± 0.1 1.5 0.35 +0.15/-0.20 D 6.3 5.8 6.6 6.6 7.8 2.6 0.65 ± 0.1 1.8 0.35 +0.15/-0.20 X 6.3 7.7 6.6 6.6 7.8 2.6 0.65 ± 0.1 1.8 0.35 +0.15/-0.20 F 8.0 10.2 8.3 8.3 10.0 3.4 0.90 ± 0.2 3.1 0.70 ± 0.2 G 10.0 10.2 10.3 10.3 12.0 3.5 0.90 ± 0.2 4.6 0.70 ± 0.2 Capacitor Markings Lot, Number: Year, Line, Month Voltage Code Voltage Vdc E 25 V 35 H 50 J 63 K 80 CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type HZA -55 ºC to +105 ºC SMT Hybrid Polymer-Aluminum Electrolytic Capacitors Part Numbering System HZA 227 M 25 F –F 24T Packaging Type Capacitance Capacitance Tolerance Voltage Code Case Code Code 227 = 220 µF M = ±20% 25 = 25 Vdc See Ratings Table 24 = Tape RoHS Compliant Indicator carrier width (mm) Film T = Tape & Reel Ratings Voltage Capacitance Rating (µF) (Vdc) CDE Part Number MAX DCL (µA) MAX MAX E.S.R. Ripple Current MAX DF @ @ @ 120 Hz/20°C 100kHz/+20°C 100kHz/+105°C (ohms) (A rms) D (mm) L (mm) Case Code QTY/reel 25 Vdc ( 32 Vdc Surge ) 33 25 HZA336M025C12T-F 8.2 0.14 0.080 0.9 5.0 5.8 C 1000 56 25 HZA566M025D16T-F 14.0 0.14 0.050 1.3 6.3 5.8 D 1000 100 25 HZA107M025X16T-F 25.0 0.14 0.030 2.0 6.3 7.7 X 900 220 25 HZA227M025F24T-F 55.0 0.14 0.027 2.3 8.0 10.2 F 500 330 25 HZA337M025G24T-F 82.5 0.14 0.020 2.5 10.0 10.2 G 500 0.9 5.0 5.8 C 1000 35 Vdc ( 44 Vdc Surge ) 22 35 HZA226M035C12T-F 7.7 0.12 0.100 27 35 HZA276M035D16T-F 9.4 0.12 0.060 1.3 6.3 5.8 D 1000 47 35 HZA476M035D16T-F 16.4 0.12 0.060 1.3 6.3 5.8 D 1000 68 35 HZA686M035X16T-F 23.8 0.12 0.035 2.0 6.3 7.7 X 900 150 35 HZA157M035F24T-F 52.5 0.12 0.027 2.3 8.0 10.2 F 500 270 35 HZA277M035G24T-F 94.5 0.12 0.020 2.5 10.0 10.2 G 500 50 Vdc ( 63 Vdc Surge ) 10 50 HZA106M050C12T-F 5.0 0.10 0.120 0.75 5.0 5.8 C 1000 22 50 HZA226M050D16T-F 11.0 0.10 0.080 1.1 6.3 5.8 D 1000 33 50 HZA336M050X16T-F 16.5 0.10 0.040 1.6 6.3 7.7 X 900 68 50 HZA686M050F24T-F 34.0 0.10 0.030 1.8 8.0 10.2 F 500 100 50 HZA107M050G24T-F 50.0 0.10 0.028 2.0 10.0 10.2 G 500 63 Vdc ( 79 Vdc Surge ) 10 63 HZA106M063D16T-F 6.3 0.08 0.120 1.0 6.3 5.8 D 1000 22 63 HZA226M063X16T-F 13.8 0.08 0.080 1.5 6.3 7.7 X 900 33 63 HZA336M063F24T-F 20.7 0.08 0.040 1.7 8.0 10.2 F 500 56 63 HZA566M063G24T-F 35.2 0.08 0.030 1.8 10.0 10.2 G 500 80 Vdc ( 100 Vdc Surge ) 22 80 HZA226M080F24T-F 17.6 0.08 0.045 1.55 8.0 10.2 F 500 33 80 HZA336M080G24T-F 26.4 0.08 0.036 1.70 10.0 10.2 G 500 CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type HZA -55 ºC to +105 ºC SMT Hybrid Polymer-Aluminum Electrolytic Capacitors Load Life Test Test Apply the maximum rated voltage for 10,000 hrs at +105 °C with full rated ripple current. After the test measure the capacitance, DF, DCL and ESR at +20 °C. Also measure the ESR at -40 °C and 100kHz. ∆C at 120Hz Capacitance will be within ±30% of the initial measured value DF at 120 Hz DF will be ≤ 200% of the initial specified value DCL after 2 minute charge Leakage current will be ≤ the initial specified value ESR at 100kHz/+20 °C ESR will be ≤ 200% of the initial specified value Max. ESR at 100kHz/-40 °C Case Code C : 2.0 Ω; Case Code D : 1.4 Ω; Case Code X : 0.8 Ω; after Load Life test Case Code F : 0.4 Ω; Case Code G : 0.3 Ω Test Subject the capacitor to 1000 hrs at +105 °C without voltage. After the test, return the capacitor to room temperature for two hours and then apply rated voltage for 30 minutes. The after test measurements for capacitance, DF, DCL and ESR at +20 °C will meet the following. ∆C at 120 Hz Capacitance will be within ±30% of the initial measured value DF at 120 Hz DF will be ≤ 200% of the initial specified value DCL after 2 minute charge Leakage current will be ≤ the initial specified value ESR at 100Khz/+20 °C ESR will be ≤ 200% of the initial specified value Moisture Resistance Test Test Subject the capacitor to 2000 hrs at +85 °C/85%RH with rated voltage. After the test, return the capacitor to room temperature and humidity for two hours. The after test measurements for capacitance, DF, DCL and ESR at +20 °C will meet the following. ∆C at 120 Hz Capacitance will be within ±30% of the initial measured value DF at 120 Hz DF will be ≤ 200% of the initial specified value DCL after 2 minute charge Leakage current will be ≤ the initial specified value ESR at 100Khz/+20 °C ESR will be ≤ 200% of the initial specified value Temperature Cycle Test Subject the capacitor to 1000 cycles of temperature change from -55 °C to +105 °C using the following sequence and durations. Test Step Temperature Time at Temperature 1 -55 ºC 30 minutes 2 +20 ºC 3 minutes max 3 +105 ºC 30 minutes 4 +20 ºC 3 minutes max After the test, return the capacitor to +20°C for one to two hours before measurement. The after test measurements for capacitance, DF, and DCL at +20 °C will meet the following; ∆C at 120 Hz Capacitance will be within ±20% of the initial measured value DF at 120 Hz DF will be ≤ 200% of the initial specified value DCL after 2 minute charge Leakage current will be ≤ the initial specified value Appearance No significant change in appearance CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Film Shelf Life Test Type HZA -55 ºC to +105 ºC Film SMT Hybrid Polymer-Aluminum Electrolytic Capacitors Reel Dimensions mm Case Dia. 5 6.3 8 10 W 14 18 26 26 t 3 3 3 3 Tape Dimensions mm Case Size Case (mm) Code 5 x 5.8 W ± 0.3 C 12 A ± 0.2 B +0.3/-0.2 C ± 0.5 5.7 5.7 F ± 0.1 P ± 0.1 t1 5.5 12 0.4 8.0 t2 ± 0.2 φd +0.1/-0 P1 ± 0.1 P2 ± 0.1 W1 ± 0.1 6.4 1.5 2 4 1.75 mm Case Size (mm) Case Code 6.3 x 5.8 D 6.3 x 7.7 X 8 x 10.2 F 10 x 10.2 G B +0.3/-0.2 C ± 0.5 W ± 0.3 A ± 0.2 16 7 7 8.7 8.7 12.5 10.7 10.7 14.5 24 9.0 F ± 0.1 P ± 0.1 t1 7.5 12 0.4 11.5 16 0.4 t2 ± 0.2 φd +0.1/-0 P1 ± 0.1 1.5 2 P2 ± W1 ± 0.1 0.1 6.4 8.4 4 1.75 11 CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type HZA -55 ºC to +105 ºC SMT Hybrid Polymer-Aluminum Electrolytic Capacitors Recommended Land Dimensions Case Code D (mm) mm A B C C 5 1.5 2.8 1.6 D 6.3 1.8 3.2 1.6 X 6.3 1.8 3.2 1.6 F 8 3.1 4.0 2.0 G 10 4.6 4.1 2.0 Recommended Reflow Soldering Film 300 Peak Temperature 250 Temperature (ºC) 30 sec. 200 230°C 200°C 70 sec. 160°C 150 120 seconds 100 50 0 Case Code Time (sec) Case Dia. Peak Time at or (mm) Temperature above 250 °C C 5 D 6.3 X 6.3 F 8 G 10 Time at or Time at or above Time at or above Number of Reflow above 230 °C 217 °C 200 °C Processes 2 260°C 5 seconds 30 seconds 40 seconds 70 seconds 1 Notes: 1. For 5mm and 6.3 mm case dia., if the peak temperature does not exceed 255 °C the time at or above 250 °C can increase to 10 seconds. 2. The capacitors in the 8m and 10 mm case dia. can withstand 2 reflow processes, if the peak temperature does not exceed 245 °C and the time at or above 240 °C does not exceed 10 seconds. 3. The 2nd reflow process should be performed after the capacitors have returned to room temperature. 4. Temperature should be measured with a thermal couple placed on the top surface of the capacitor. 5. After reflow soldering, the leakage current, D.F., and e.s.r., will meet the initial specifications, and the capacitance will be within ±10% of the initial measured value when measured at room conditions. CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Type HZA -55 ºC to +105 ºC SMT Hybrid Polymer-Aluminum Electrolytic Capacitors Capacitor Temperature Characteristics 33 µF/25V 30 20 0.15 10 0 0.1 -10 0.05 -20 -30 -40 Film 0.2 D.F. Capacitance Change (%) 40 0 -60 -40 -20 0 20 40 Temperature (ºC) 60 80 100 120 -60 -40 -20 0 20 40 Temperature (ºC) 60 80 100 120 10 100 Initial E.S.R. (ohms) Initial Impedance (ohms) 120 Hz 10 1 KHz 1 10 KHz 0.1 0.01 100 KHz 1 KHz 1 kHz 0.1 10 kHz 10 KHz 100 kHz 100 KHz 0.01 -60 -10 40 90 120 Hz 120 Hz 1 140 -60 -40 -20 0 20 40 60 80 100 120 Temperature (ºC) Temperature (ºC) 10 33 µF/25V at +105 ºC with rated voltage Spec. Limit: ±30% 0.5 0 0.4 -10 0.3 D.F. Capacitance Change (%) Life Test Results -20 0.2 0.1 -30 -40 Spec. Limit: 0.28 0 2000 4000 hours 6000 8000 0 10000 0 4000 Spec. Limit: 8.2 µA 20 DCL (µA) after 2 min at rated voltage 2000 6000 8000 10000 hours 15 10 5 0 0 2000 4000 hours 6000 8000 10000 CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 Film Notice and Disclaimer: All product drawings, descriptions, specifications, statements, information and data (collectively, the “Information”) in this datasheet or other publication are subject to change. The customer is responsible for checking, confirming and verifying the extent to which the Information contained in this datasheet or other publication is applicable to an order at the time the order is placed. All Information given herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has of operating conditions that such Cornell Dubilier company regards as typical for such applications, but are not intended to constitute any guarantee, warranty or representation regarding any such matter – and Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning the suitability for a specific customer application, use, storage, transportation, or operating environment. The Information is intended for use only by customers who have the requisite experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality and safety standards regarding the design and manufacturing of its products, in light of the current state of the art, isolated component failures may still occur. Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage. Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be required.