Ordering information Rugged PCB type LEP150F LEP 150 1 2 F 3 -24 4 Recommended Noise Filter NAC-06-472 R High voltage pulse noise type : NAP series Low leakage current type : NAM series *The Noise Filter is recommended *to connect with several devices. MODEL DC OUTPUT LEP150F-24 +24V 6.3(Peak 12)A LEP150F-36 +36V 4.2(Peak 8)A -O 5 1Series name 2Output wattage 3Universal input 4Output voltage 5Optional *1 G :Low leakage current R :with Remote ON/OFF S :with Chassis SN:with Chassis & cover T :Vertical terminal block U :Operating stop voltage is set at a lower value Z :with ZT LEP150F-48 +48V 3.2(Peak 6)A SPECIFICATIONS MODEL VOLTAGE[V] LEP CURRENT[A] ACIN 100V ACIN 200V FREQUENCY[Hz] INPUT OUTPUT PROTECTION CIRCUIT AND OTHERS ISOLATION ENVIRONMENT SAFETY AND NOISE REGULATIONS OTHERS ACIN 100V ACIN 200V ACIN 100V POWER FACTOR ACIN 200V ACIN 100V INRUSH CURRENT[A] ACIN 200V LEAKAGE CURRENT[mA] VOLTAGE[V] CURRENT[A] *2 WATTAGE[W] LINE REGULATION[mV] LOAD REGULATION[mV] 0 to +45C *3 RIPPLE[mVp-p] -10 - 0C *3 0 to +45C *3 RIPPLE NOISE[mVp-p] -10 - 0C *3 0 to +45C TEMPERATURE REGULATION[mV] -10 to +45C DRIFT[mV] *4 START-UP TIME[ms] HOLD-UP TIME[ms] OUTPUT VOLTAGE ADJUSTMENT RANGE[V] OUTPUT VOLTAGE SETTING[V] OVERCURRENT PROTECTION OVERVOLTAGE PROTECTION REMOTE ON/OFF INPUT-OUTPUT -RC *5 INPUT-FG OUTPUT-RC-FG *5 OUTPUT-RC *5 OPERATING TEMP.,HUMID.AND ALTITUDE STORAGE TEMP.,HUMID.AND ALTITUDE VIBRATION IMPACT AGENCY APPROVALS CE MARKING CONDUCTED NOISE HARMONIC ATTENUATOR CASE SIZE/WEIGHT COOLING METHOD EFFICIENCY[%] LEP150F-24 LEP150F-36 LEP150F-48 AC85 - 264 1f or DC 120 - 370 2.0typ (Io=100%) 1.0typ (Io=100%) 50/60 (47 - 63) or DC 82typ (Io=100%) 83typ (Io=100%) 84typ (Io=100%) 85typ (Io=100%) 86typ (Io=100%) 87typ (Io=100%) 0.98typ (Io=100%) 0.93typ (Io=100%) 15typ (Io=100%) (At cold start) (Ta=25 C) 30typ (Io=100%) (At cold start) (Ta=25 C) 0.75max (60Hz, According to IEC60950 and DEN-AN) +24 +36 +48 0 - 6.3 (Peak 12) 0 - 4.2 (Peak 8) 0 - 3.2 (Peak 6) 151.2 (Peak 288) 151.2 (Peak 288) 153.6 (Peak 288) 48max 48max 48max 76max 90max 150max 120max 120max 150max 160max 160max 300max 150max 150max 250max 180max 180max 350max 120max 150max 240max 145max 180max 300max 48max 48max 48max 500max (ACIN 100V, Io=100%) 20typ (ACIN 100V, Io=100%) 21.4 - 26.4 26.4 - 39.6 39.6 - 52.8 23.0 - 25.0 35.0 - 37.0 46.0 - 50.0 Works over 101% of peak current and recovers automatically Works at 115 - 140% of rating Option (Refer to Instruction Manual) AC3,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC2,000V 1minute, Cutoff current = 10mA, DC500V 50MW min (At Room Temperature) AC500V 1minute, Cutoff current = 100mA, DC500V 50MW min (At Room Temperature) AC100V 1minute, Cutoff current = 100mA, DC100V 10MW min (At Room Temperature) -10 to +70C, 20 - 90%RH (Non condensing) (Refer to DERATING CURVE), 3,000m (10,000feet) max -20 to +75C, 20 - 90%RH (Non condensing), 9,000m (30,000feet) max 10 - 55Hz, 19.6m/s2 (2G), 3minutes period, 60minutes each along X, Y and Z axis 196.1m/s2 (20G), 11ms, once each X, Y and Z axis UL60950-1, C-UL(CSA60950-1), EN60950-1, EN50178 Complies with DEN-AN and IEC60950-1 (At only AC input) Low Voltage Directive, EMC Directive Complies with FCC-B, CISPR22-B, EN55022-B, VCCI-B Complies with IEC61000-3-2 85X40X222mm (WXHXD) /490g max (without chassis and cover) Convection *1 Specification is changed at option, refer to Instruction Manual 6. *2 Peak loading for 10sec. And Duty 35% max, refer to Instruction Manual 5. In detail. *3 This is the value that measured on measuring board with capacitor of 22mF within 150mm from output terminal.Measured by 20MHz oscilloscope or Ripple-Noise meter (Equivalent to KEISOKU-GIKEN: RM101). *4 Drift is the change in DC output for an eight hour period after a half-hour warm-up at 25C, with the input voltage held constant at the rated input/output. E-6 *5 * * * Applicable when remote control (optional) is added. Parallel operation with other model is not possible. Derating is required when operated with chassis and cover. A sound may occur from power supply at peak loading. LEP150F External view Voltage adjust 5-º3.5 Mounting Hole 47 95 CN1 4.5 +V CN2 1 4 5 8 55-+0.5 35-+0.5 -V 4-M4 Mounting Hole 8 CN2 C119 (68) 75 -+0.5 85 CN1 5 FG 3 Input(N) 1 Input(L) 235-+0.5 2-º4.5 20 (215) 30 Name plate CN3 5 CN4 Connector for Remote ON/OFF (option) 105 -+ 0.5 212 -+ 0.5 CN3 CN4 Connector for -Z (option) 252 235-+0.5 º4.5 2-M4 8 CN4 4.5 CN3 25 37 Mounting Hole (Lead) RC(-) 3max 51 222 15 5 RC(+) + COM - PCB t=1.6 PIN CONNECTION I / O Connector Mating Connector Terminal Chain : SVH-21T-P1.1 CN1 VHR-5N B3P5-VH Loose: BVH-21T-P1.1 Chain : SVH-21T-P1.1 CN2 VHR-8N B8P-VH Loose: BVH-21T-P1.1 Chain : SXH-001T-P0.6 CN3 XHP-2 (Option) B2B-XH-A Loose: BXH-001T-P0.6 Chain : SXH-001T-P0.6 CN4 XHP-3 B3B-XH-A (Option) Loose: BXH-001T-P0.6 (Mfr: J.S.T.) CN1 Pin No. Input 1 AC(L) 2 3 AC(N) 4 5 FG CN2 Pin No. Output 1, 2, 3, 4 -V 5, 6, 7, 8 +V CN3 (Option) Pin No. Remote ON/OFF 1 RC(+) 2 RC(-) ¶Weight: 490g or less (Without chassis and cover) ¶Tolerance: t1 ¶Dimensions in mm. ¶PCB Material : CEM3 ¶Chassis and cover is optional. ¶Mounting torque: 1.5N · m(16kgf · cm)max CN4 (Option) Pin No. -Z 1 + COM 2 3 ¶Keep drawing current per pin below 5A(7A at peak load)for CN2 Performance data ¡RISE TIME & FALL TIME (LEP150F-24) ¡EFFICIENCY (LEP150F-24) 88 86 ACIN 100V Io=100% EFFICIENCY 84 DC Output 82 80 AC Input 78 100ms/DIV 76 60 20ms/DIV ¡INPUT HARMONIC CURRENT (LEP150F-24) 140 180 220 260 300 V ¡INPUT HARMONIC CURRENT (LEP150F-24) 10 HARMONIC CURRENT Load factor 100% Input voltage AC 100V 1 0.1 0.01 10 20 30 Harmonic current standard class A (at odd number) A Harmonic current standard class A (at odd number) A HARMONIC CURRENT 100 INPUT VOLTAGE 10 0.001 0 Load factor100% Load factor 50% 1 Load factor 100% Input voltage AC 230V 0.1 0.01 0.001 0 40 HARMONIC ORDER 10 20 Distribution: RSG Electronic Components GmbH Sprendlinger Landstr. 115 D-63069 Offenbach/Germany Tel. +49 69 984047-0 Fax +49 69 984047-77 [email protected] www.rsg-electronic.de ■ ■ Änderungen vorbehalten / subject to change without notice 30 40 HARMONIC ORDER ■ ■ ■ E-7 LEP