NSC FPD33684A Low power, low emi, tft-lcd column driver with rsdsâ ¢ inputs, 64 grayshades, and 384 outputs for xga/sxga application Datasheet

FPD33684A/ FPD33684B
Low Power, Low EMI, TFT-LCD Column Driver with
RSDS™ Inputs, 64 Grayshades, and 384 Outputs for
XGA/SXGA Applications
General Description
Features
The FPD33684 Column Driver is a direct drive, 64 gray level,
384 output, TFT-LCD column driver with an RSDS™ data
interface. It provides the capability to display 262,144 colors
(18-bit color) with a large dynamic output range for twisted
nematic applications. When used in a bank with other
FPD33684 column drivers, the FPD33684 can support both
XGA (8 drivers) or SXGA (10 drivers) applications. Output
voltages are programmably gamma corrected to provide a
direct mapping between digital video and LCD panel brightness.
An RSDS™ (Reduced Swing Differential Signaling) interface
is used between the timing controller and the column driver
to minimize EMI and reduce power.
The FPD33684 offers a low power, low EMI column driver
solution with direct-drive dynamic range and dot-inversion
addressing.
n RSDS™ (Reduced Swing Differential Signaling) data
bus for low power, reduced EMI and small PCB foot
print
n Up to 85MHz clock
n Supports both XGA and SXGA timing
n Supports notebook and monitor applications
n Smart Charge Conservation for low power consumption
n 64 Gray levels per color (18-bit color)
n Supports both Dot and N-Line inversion
n Externally programmable gamma characteristic
n Very low offsets for artifact-free images
n High voltage outputs for high contrast in a large range of
display panel applications
n Optional, high current, repair line buffers
n Available in 2 common gamma reference curves
Ordering Information
Part Number
Gamma Curve
Custom TCP #
Package Suffix
FPD33684
A or B
XX(Note 1)
CT
Note 1: Custom TCP # is assigned by National Semiconductor for each custom TCP design
System Diagram
DS200113-1
© 2002 National Semiconductor Corporation
DS200113
www.national.com
FPD33684 Low Power, Low EMI, TFT-LCD Column Driver with RSDS Inputs, 64 Grayshades, and
384 Outputs for XGA/SXGA Applications
May 2002
FPD33684
Note 2: “Absolute Maximum Ratings” are those values beyond which the
safety of the device cannot be guaranteed. They are not meant to imply that
the devices should be operated at these limits. The table of “Electrical
Characteristics” specifies conditions of device operation.
Absolute Maximum Ratings (Note 2)
Analog Supply, (VDD2) (Note 3)
Logic Supply, (VDD1) (Note 3)
High Bias Supply, (VHBIAS) (Note 3)
Low-Polarity RDAC Reference
Voltages, (VGMA6 to VGMA10)
(Note 3)
High-Polarity RDAC Reference
Voltages, (VGMA1 to VGMA5)
(Note 3)
RDAC Current (All Gamma Voltage
Taps), (IGMA to IGMA10)
Input Voltage (Digital Logic), (VIN)
(Note 3)
Output Voltage, (VOUT) (Note 3)
Output Current (Analog), (IOUT)
Storage Temperature Range, (TS)
−0.3V to +11.5V
−0.3V to +5.0V
−0.3V to +13.0V
Note 3: Absolute voltages referenced to VSS1 = VSS2 = 0.0V.
Recommended Operating
Conditions
−0.3V to 0.5VDD2
0.5VDD2 − 1.0V to
VDD2 + 0.3V
Logic Supply Voltage
(VDD1)
Supply Voltage (VDD2)
Supply Voltage (VHBIAS)
Operating Temperature
(TA)
−2.5mA to 2.5mA
−0.3V to VDD1 + 0.3V
−0.3V to VDD2 + 0.3V
−7mA to +7mA
−55˚C to +125˚C
Min
2.7
Typ
3.3
7.5
VDD2
−10
Max
3.6
Units
V
10.5
VDD2+1.5
+25
V
V
+70
˚C
DC Electrical Characteristics
Digital Electrical Characteristics
Symbol
Parameter
Conditions
Min
VIH
Logic Input High Voltage
VIL
Logic Input Low Voltage
VOH
Logic Output High Voltage
IOH = −0.5mA
VOL
Logic Output Low Voltage
IOL = 0.5mA
IDD1
Logic Current
(Note 4)
IIH
Input Leakage
VDD1 = 3.6V, VIN = 3.6V
-1
IIL
Input Leakage
VDD1 = 3.6V, VIN = 0V
-1
CIN
Input Capacitance
All logic pins
Typ
Max
0.7
VDD1
Units
V
0.3
VDD1
VDD1 −
0.5
V
V
3.0
0.5
V
8.0
mA
1
µA
1
µA
2
pF
Note 4: CLK frequency = 32.5 MHz, VDD1 = 3.3V, VSS1 = VSS2 = 0.0V, charge share time = 1.5µs, line time = 22µs.
RSDS Characteristics
Symbol
Parameter
Conditions
VIHRSDS
RSDS™ High Input Voltage
VCMRSDS = 1.2V (Note 5) see
Figure 1
VILRSDS
RSDS™ Low Input Voltage
VCMRSDS = 1.2V (Note 5) see
Figure 1
VCMRSDS
RSDS™ Common Mode Input
Voltage Range
VIHRSDS = +100mV, VILRSDS =
−100mV (Note 6) see Figure 1
IDL
RSDS™ Input Leakage Current
DxxP, DxxN, CLKP, CLKN
Min
Typ
100
200
−200
Max
Units
mV
−100
mV
VSS1 +
0.1
VDD1 −
1.3
V
−10
10
µA
Note 5: VCMRSDS = (VCLKP + VCLKN)/2 or (VDxxP + VDxxN)/2.
Note 6: Positive means that DxxP (or CLKP) is higher than RSDS ground DxxN (or CLKN). Negative means that DxxP (or CLKP) is lower than RSDS ground DxxN
(or CLKN).
www.national.com
2
FPD33684
RSDS Characteristics
(Continued)
DS200113-2
FIGURE 1. RSDS™ Signal Definition
Analog Electrical Characteristics
Symbol
IDD2
IHBIAS
Parameter
Supply Current Consumption
Conditions
Min
(Note 7)
Current Consumption through
HBIAS pin
Typ
Max
Units
3.0
8.0
mA
1.25
mA
45
mW
PD
Power Dissipation
(Note 7)
VGMA1
Upper RDAC High Side Input
(Note 8)
VDD2/2
+ 0.2
VDD2 −
0.2
V
VGMA5
Upper RDAC Low Side Input
(Note 8)
VDD2/2
+ 0.2
VDD2 −
0.2
V
VGMA6
Lower RDAC High Side Input
(Note 8)
0.2
VDD2/2
− 0.2
V
VGMA10
Lower RDAC Low Side Input
(Note 8)
0.2
VDD2/2
− 0.2
V
VCS
Charge Share Voltage
The
Greater
of VDD1
or
VGMA6
VGMA5
V
CLOAD
Output Capacitive Load
30
150
pF
VOUT
Output Voltage Range
VSS2 +
0.2
VDD2 −
0.2
V
RDAC
RDAC References (VGMA1 to
VGMA5 and VGMA6 to VGMA10)
each
15.0
18.0
kΩ
Vpperr
Output Peak to Peak Error (gray
levels 0 through 58)
VGMA1 = VDD2 − 0.2V
VGMA10 = VSS2 + 0.2V
(Note 9)
±3
± 12
mV
±5
± 25
mV
±5
mV
Output Peak to Peak Error (gray
levels 59 through 63)
Vparterr
Output Part to Part Error
(Note 10)
IOUT RP
Repair Buffer Output Current
(Note 11)
12.0
±2
±3
mA
Note 7: VDD2 = 10.5V, VHBIAS = 10.5V, VDD1 = 3.3V, DCLK = 65 MHz, RLOAD = 5 kΩ, CLOAD = 50 pF, charge share time = 1.5 µs, all other swinging between
VGMA1 (= 8.0V) and VGMA10 (= 0.5V) with a line time = 22 µs.
Note 8: The following relationship must be maintained between the reference voltages: VDD2 > VGMA1 > VGMA2 > VGMA3 > VGMA4 > VGMA5 > VGMA6 > VGMA7
> VGMA8 > VGMA9 > VGMA10 > VSS2
Note 9: Vpperr is defined as the error in peak-to-peak output voltage for each gray level when the output swings from the gray level high value (VHxx) to the gray
level low value (VLxx). This parameter applies to every output on the die. The typical value represents one standard deviation from ideal based on final test data.
Note 10: Vparterr is meant to guarantee the part to part output variation. The average of all outputs at gray level 32 is compared to a nominal gray level 32 value.
Note 11: Current into device pins is defined as positive. Current out of device pins is defined as negative. |VOUT − VIN| > 500mV.
3
www.national.com
FPD33684
AC Electrical Characteristics
Digital AC Characteristics
Symbol
Parameter
PWCLK
Clock Period
PWCLK(L)
PWCLK(H)
Conditions
Min
Typ
Max
Units
11.7
ns
Low Clock Pulse Width
5
ns
High Clock Pulse Width
5
ns
tsetup1
RSDS Data Setup Time
2
ns
thold1
RSDS Data Hold Time
0
ns
tsetup2
ENIOx Setup Time
2
ns
thold2
ENIOx Hold Time
4
tPLH1
Start Pulse Fall Delay
PWDIO
ENIOx Pulse Width
PWCLK1
LOAD Pulse Width
tLDT
Last Clock to LOAD Delay
ns
CLINE = 15 pF
8
ns
1
2
TCLK
5 TCLK
5µs
5
TCLK
tDENSU
LOAD to First ENIO Setup
2
TCLK
tPOL–CLK1
POL–CLK1 Time
14
ns
Analog AC Characteristics
Supplies: VSS1 = VSS2 = 0.0V, VDD1 = 3.3V, VDD2 = +9.5V, VHBIAS = 11.0V.
Symbol
Parameter
Conditions
Max
Units
6
µs
10
µs
CLOAD = 150 pF,
(Note 12)
6
µs
CLOAD = 150 pF,
(Note 12)
10
µs
tsettle 90%
Output Settling Time to 90% of
Final Value
Figure 2 (Note 12)
t6-bit accy
Output Settling Time to 6-bit
accuracy
Figure 2 (Note 12)
tRP 90%
Repair Line Output Settling Time
to 90% of Final Value
tRP 6-bit accy
Repair Line Output Settling Time
to 6-bit accuracy
Min
Note 12: Charge Share Time = 800ns, VGMA1 = 10.3V, VGMA10 = 0.2V, VGMA5 = 5.45V, VGMA6 = 5.05V.
DS200113-11
FIGURE 2. Test Circuit for Output Settling Time Measurements
www.national.com
4
Typ
FPD33684
DS200113-3
Timing Diagrams
5
www.national.com
FPD33684
Timing Diagrams
(Continued)
DS200113-4
DS200113-5
www.national.com
6
FPD33684
Block Diagram
DS200113-6
64 gray level voltages on each output. Output voltages are
driven with individual high drive, low offset operational amplifiers. Data loading and line buffering is accomplished by
means of an internal, bi-directional shift register.
Functional Description
GENERAL OVERVIEW
The FPD33684 is a low power, low EMI, 384 output column
driver with 64 gray level capability (6-bit). It provides direct
drive for TFT-LCD displays, eliminating the need for Vcom
modulation. Direct drive significantly reduces system power
consumption and also reduces component count while providing superior image quality and cross-talk margin. The
FPD33684 utilizes National’s Charge Conservation Technology that recovers energy stored in the capacitance of the
column lines to reduce power consumption further.
The FPD33684 is designed for use in systems using dot
inversion as the method of polarity inversion. Column inversion and N-line inversion are also supported. Other modes of
polarity inversion including line inversion and frame inversion
are not supported.
Digital video data inputs to the FPD33684 are received via a
low power, low EMI Reduced Swing Differential Signaling
(RSDS™) bus. The RSDS™ digital video commands one of
GAMMA CORRECTION
The FPD33684 is designed to offer compatibility with a wide
range of panel gamma characteristics. The output voltage is
controlled by the digital data on the RSDS™ bus. Two identical R-DACs are used to program the output voltages. One
R-DAC provides the high-polarity output voltages (voltages
higher than Vcom) and the other provides the low-polarity
output voltages (voltages lower than Vcom).
The FPD33684 is available with two R-DAC resistance curve
options, both of which have been carefully designed to accurately match the natural, inverse gamma of a twisted
nematic (TN) display with a 2.2 gamma transfer characteristic. A typical TN display, when operated with the FPD33684
drivers will produce a luminance with grayscale characteristics typical of CRT monitors. The R-DAC resistance values
for the FPD33684A are shown in Figure 3 and Figure 4. The
7
www.national.com
FPD33684
Functional Description
VCSTIME,will then decay toward GND at a rate determined by
the RCSTIME and CCSTIME time constant. When VCSTIME
reaches VDD1/2 the output mode switches from charge sharing to conventional amplifier drive mode. The charge-share
mode time can be calculated using the following equation:
tcharge-share = 0.69 x RCSTIME x CCSTIME
(Continued)
R-DAC resistance values for the FPD33684B (designed to
match the gamma curve of the Samsung S6C0666) are
shown in Figure 5 and Figure 6. Most applications will only
need to provide references for each of the two ends of the
two R-DACs (GMA1, GMA5, GMA6, and GMA10). Six additional, intemediate R-DAC tap points are available for further
customization.
RSDS™ DATA CHANNEL
The RSDS™ data bus is comprised of nine differential data
pairs and a differential clock. The nine channels are organized as three busses of three channels each. Each three
channel bus corresponds on one of the three video colors,
red, green and blue. Because the clocking is dual edged, the
even fields of the 6-bit word are transmitted-received on a
first clock and are followed by the odd fields. One full pixel
(red, green, and blue subpixels) is transmitted every full
pixelclock cycle.
CHARGE CONSERVATION TECHNOLOGY
National Semiconductor’s proprietary charge conservation
technology significantly reduces power consumption.
Charge conservation works by briefly switching all of the
columns at the start of each line to a common node. This has
the effect of redistributing the charge stored in the capacitance of the panel columns. Because half the columns are at
voltages more positive than Vcom and half are more negative, this redistribution of charge or “charge-sharing” has the
effect of pulling all of the columns to a neutral voltage near
the middle of the driver’s dynamic range. Thus, the voltages
on all the columns are driven approximately halfway toward
their next value with no power expended. This dramatically
reduces panel power dissipation (up to a theoretical limit of
50%) compared to conventional drivers which must drive
each column through the entire voltage swing every time
polarity is reversed.
’Smart’ charge sharing is used to further optimize this feature. Data inversion is monitored and charge shared only
across data ranges (when output polarity changes between
adjacent lines). This is useful during n-line inversion when
polarity changes do not occur at every line transition.
Charge sharing enables the FPD33684 to have faster output
rise and fall times than drivers with convential amplifiers.
This is due to the fact that the instantaneous currents supplied by the energy stored in the panel are much higher than
the maximum output current of conventional drivers.
CSTIME — CHARGE SHARE TIME
OPTIONAL LINE BUFFERS
The FPD33684 provides two general purpose, unity gain
output buffers, one located at each end of the input bank of
the die. These buffers may be used to repair an open column
line. The drive signal from the output of the faulted line can
be stitched to the input of the repair buffer during the repair
process. The output of the repair buffer is then routed to the
other side of the column line making it possible to maintain
fast rise and fall times on both ends of the afflicted column
line.
PIN DESCRIPTIONS
The pin order configuration for the FPD33684 is shown in
Figure 7. Optional pins do not need to be carried off a
custom TCP or COF package but may require a connection
to a neighboring pad on the die by a tie on the tape.
CLKP and CLKN — DATA CLOCK (INPUT)
Differential clock input for RSDS™ data loading.
D00P–D22N — RSDS™ DATA BUS (INPUT)
D0xP–D0xN — Data for OUTPUTS 1,4,7...382 (red)
D1xP–D1xN — Data for OUTPUTS 2,5,8...383 (green)
D2xP–D2xN — Data for OUTPUTS 3,6,9...384 (blue)
Where x = 0 (LSB), 1 or 2 (MSB).
ENIO1/ENIO2 — DATA LOADING ENABLE 1 AND 2 (I/O)
The CSTIME pin allows the user to set the duration of
charge-sharing mode based on the panel capacitance and
resistance. The length of charge-sharing is important because it must be long enough to allow all of the columns to
equalize to the same value in order to achieve optimum
power performance. The length of charge-mode is user programmable. There are two common methods to drive the
CSTIME pin.
The first method is to actively drive the CSTIME input with a
control signal. This may be achieved by connecting the
LOAD signal to the CSTIME input.The width of the
LOAD/CSTIME signal determines the amount of time spent
in charge-sharing. This width may be optimized for a particular panel load. A ’typical’ width is 800ns. If desired, the
CSTIME pin may be driven independently, however, this will
require an additional output from the timing controller.
At the rising edge of the CSTIME/LOAD input signal, the
outputs enter charge-sharing mode. Outputs remain in
charge-mode until the falling edge of the CSTIME/LOAD
signal.
A second method for setting charge-time is to connect a
resistor (RCSTIME) and capacitor (CCSTIME) in parallel between the CSTIME pin and ground. Only one resistor and
capacitor is required for the entire display. At the rising edge
of the LOAD signal, the CSTIME pin is internally pulled to
VDD1 and then released (i.e. floated). At this time the outputs
enter charge-sharing mode. The voltage on the CSTIME pin,
www.national.com
The ENIO1/ ENIO2 pins are used to daisy chain the
FPD33684 together with other FPD33684s. The first input in
the chain is normally connected to the SP signal (or it’s
equivalent) on the timing controller. If UP = H, then the
ENIO1 pin is configured as an input and the ENIO2 pin is
configured as an output. If UP = L, then the ENIO2 pin is
configured as an input and the ENIO1 pin is configured as an
output.
INVERT — DIGITAL DATA INVERT (INPUT)
When INVERT = H, RSDS data is inverted. The INVERT pin
can be tied either high or low through connection to a neighboring pin, eliminating the need to bring the pin off the
package.
LOAD — DATA LOAD (INPUT)
The rising edge of LOAD copies the digital video buffered by
the shift register into a second latch for conversion to analog.
The outputs are forced into charge share mode while load is
high. When CSTIME = LOAD the falling edge ends the
charge share time and the newly converted analog voltages
are driven by the outputs.
POL — POLARITY (INPUT)
8
The CSTIME pin allows the user to set the duration of
charge-sharing mode based on the panel capacitance and
resistance.
VDD1 — DIGITAL VOLTAGE SUPPLY
(Continued)
When POL = L, odd numbered outputs (1, 3, 5, ...383) are
controlled by VGMA6 through VGMA10 and even numbered
outputs are controlled by VGMA1 through VGMA5. When
POL = H, odd numbered outputs are controlled by VGMA1
through VGMA5 and even numbered outputs are controlled
by VGMA6 through VGMA10.
Positive supply voltage for the digital logic functions of the
driver.
VDD2 — ANALOG VOLTAGE SUPPLY
Positive supply voltage for the analog functions of the driver.
VGMA1–VGMA10 — RDAC REFERENCES (INPUTS)
RPI1/ RPI2 — REPAIR INPUT 1 AND 2 (INPUT)
The input signal for the repair line buffers. These buffers are
optional and when not used, the input should be tied to
ground. The pin can be tied to ground through a local pin on
the TCP, eliminating the need to bring the repair amp inputs
or outputs off the TCP.
The reference voltages to the upper and lower RDACs used
to control the inverse gamma transfer function of the driver.
Option - Any or all of the inputs VGMA2 through VGMA4 and
VGMA7 through VGMA9 can be left undriven (floating).
VHBIAS — HIGH BIAS CURRENT VOLTAGE SUPPLY
RPO1/ RPO2 — REPAIR OUTPUT 1 AND 2 (OUTPUT)
The output of the repair line buffers. These outputs are
current buffered copies of their respective inputs.
UP — DATA SHIFT DIRECTION — UP OR DOWN (INPUT)
Optional positive supply voltage that provides a constant
bias current to the output amplifiers to extend dynamic
range. When separately provided, VHBIAS must be 1.5V
greater than VGMA1. When not separately provided, VHBIAS
must be tied to VDD2. In this configuration, VGMA1 must be
held at or below VDD2 −1.5V.
VSS1 — DIGITAL GROUND
Digital ground reference voltage.
VSS2 — ANALOG GROUND
Analog ground reference voltage.
The UP pin controls the data shift direction. If UP is high then
data is shifted “up” from output 1 to output 384, ENIO1 is
configured as an input, and ENIO2 is an output. If UP is low
then data is shifted “down” from output 384 to output 1,
ENIO2 is an input, and ENIO1 is an output. The UP pin can
be tied either high or low through connection to a neighboring pin, eliminating the need to bring the pin off the package.
CSTIME — CHARGE SHARE TIME
9
www.national.com
FPD33684
Functional Description
FPD33684
Functional Description
(Continued)
RH1
RDAC x 123/1008
RH32
RDAC x 7/1008
RH2
RDAC x 69/1008
RH33
RDAC x 7/1008
RH3
RDAC x 49/1008
RH34
RDAC x 7/1008
RH4
RDAC x 42/1008
RH35
RDAC x 7/1008
RH5
RDAC x 35/1008
RH36
RDAC x 7/1008
RH6
RDAC x 28/1008
RH37
RDAC x 7/1008
RH7
RDAC x 28/1008
RH38
RDAC x 7/1008
RH8
RDAC x 21/1008
RH39
RDAC x 7/1008
RH9
RDAC x 21/1008
RH40
RDAC x 7/1008
RH10
RDAC x 14/1008
RH41
RDAC x 7/1008
RH11
RDAC x 14/1008
RH42
RDAC x 7/1008
RH12
RDAC x 10/1008
RH43
RDAC x 7/1008
RH13
RDAC x 10/1008
RH44
RDAC x 8/1008
RH14
RDAC x 9/1008
RH45
RDAC x 8/1008
RH15
RDAC x 9/1008
RH46
RDAC x 8/1008
RH16
RDAC x 8/1008
RH47
RDAC x 8/1008
RH17
RDAC x 8/1008
RH48
RDAC x 8/1008
RH18
RDAC x 8/1008
RH49
RDAC x 8/1008
RH19
RDAC x 8/1008
RH50
RDAC x 8/1008
RH20
RDAC x 8/1008
RH51
RDAC x 9/1008
RH21
RDAC x 7/1008
RH52
RDAC x 9/1008
RH22
RDAC x 7/1008
RH53
RDAC x 10/1008
RH23
RDAC x 7/1008
RH54
RDAC x 10/1008
RH24
RDAC x 7/1008
RH55
RDAC x 10/1008
RH25
RDAC x 7/1008
RH56
RDAC x 10/1008
RH26
RDAC x 7/1008
RH57
RDAC x 13/1008
RH27
RDAC x 7/1008
RH58
RDAC x 15/1008
RH28
RDAC x 7/1008
RH59
RDAC x 17/1008
RH29
RDAC x 7/1008
RH60
RDAC x 21/1008
RH30
RDAC x 7/1008
RH61
RDAC x 35/1008
RH31
RDAC x 7/1008
RH62
RDAC x 48/1008
RH63
RDAC x 62/1008
DS200113-9
FIGURE 3. FPD33684A R-DAC Transfer Characteristic (continued in next figure)
www.national.com
10
FPD33684
Functional Description
(Continued)
RL1
RDAC x 123/1008
RL32
RDAC x 7/1008
RL2
RDAC x 69/1008
RL33
RDAC x 7/1008
RL3
RDAC x 49/1008
RL34
RDAC x 7/1008
RL4
RDAC x 42/1008
RL35
RDAC x 7/1008
RL5
RDAC x 35/1008
RL36
RDAC x 7/1008
RL6
RDAC x 28/1008
RL37
RDAC x 7/1008
RL7
RDAC x 28/1008
RL38
RDAC x 7/1008
RL8
RDAC x 21/1008
RL39
RDAC x 7/1008
RL9
RDAC x 21/1008
RL40
RDAC x 7/1008
RL10
RDAC x 14/1008
RL41
RDAC x 7/1008
RL11
RDAC x 14/1008
RL42
RDAC 7/1008
RL12
RDAC x 10/1008
RL43
RDAC x 7/1008
RL13
RDAC x 10/1008
RL44
RDAC x 8/1008
RL14
RDAC x 9/1008
RL45
RDAC x 8/1008
RL15
RDAC x 9/1008
RL46
RDAC x 8/1008
RL16
RDAC x 8/1008
RL47
RDAC x 8/1008
RL17
RDAC x 8/1008
RL48
RDAC x 8/1008
RL18
RDAC x 8/1008
RL49
RDAC x 8/1008
RL19
RDAC x 8/1008
RL50
RDAC x 8/1008
RL20
RDAC x 8/1008
RL51
RDAC x 9/1008
RL21
RDAC x 7/1008
RL52
RDAC x 9/1008
RL22
RDAC x 7/1008
RL53
RDAC x 10/1008
RL23
RDAC x 7/1008
RL54
RDAC x 10/1008
RL24
RDAC x 7/1008
RL55
RDAC x 10/1008
RL25
RDAC x 7/1008
RL56
RDAC x 10/1008
RL26
RDAC x 7/1008
RL57
RDAC x 13/1008
RL27
RDAC x 7/1008
RL58
RDAC x 15/1008
RL28
RDAC x 7/1008
RL59
RDAC x 17/1008
RL29
RDAC x 7/1008
RL60
RDAC x 21/1008
RL30
RDAC x 7/1008
RL61
RDAC x 35/1008
RL31
RDAC x 7/1008
RL62
RDAC x 48/1008
RL63
RDAC x 62/1008
DS200113-10
FIGURE 4. FPD33684A R-DAC Transfer Characteristic (continued from prior figure)
11
www.national.com
FPD33684
Functional Description
(Continued)
RH1
RDAC x 27/1008
RH32
RDAC x 10/1008
RH2
RDAC x 27/1008
RH33
RDAC x 9/1008
RH3
RDAC x 27/1008
RH34
RDAC x 9/1008
RH4
RDAC x 27/1008
RH35
RDAC x 9/1008
RH5
RDAC x 27/1008
RH36
RDAC x 9/1008
RH6
RDAC x 27/1008
RH37
RDAC x 9/1008
RH7
RDAC x 27/1008
RH38
RDAC x 9/1008
RH8
RDAC x 27/1008
RH39
RDAC x 9/1008
RH9
RDAC x 27/1008
RH40
RDAC x 9/1008
RH10
RDAC x 27/1008
RH41
RDAC x 9/1008
RH11
RDAC x 27/1008
RH42
RDAC x 9/1008
RH12
RDAC x 27/1008
RH43
RDAC x 9/1008
RH13
RDAC x 24/1008
RH44
RDAC x 9/1008
RH14
RDAC x 24/1008
RH45
RDAC x 9/1008
RH15
RDAC x 21/1008
RH46
RDAC x 9/1008
RH16
RDAC x 20/1008
RH47
RDAC x 10/1008
RH17
RDAC x 18/1008
RH48
RDAC x 10/1008
RH18
RDAC x 18/1008
RH49
RDAC x 11/1008
RH19
RDAC x 18/1008
RH50
RDAC x 12/1008
RH20
RDAC x 17/1008
RH51
RDAC x 12/1008
RH21
RDAC x 16/1008
RH52
RDAC x 13/1008
RH22
RDAC x 15/1008
RH53
RDAC x 13/1008
RH23
RDAC x 14/1008
RH54
RDAC x 14/1008
RH24
RDAC x 14/1008
RH55
RDAC x 14/1008
RH25
RDAC x 13/10078
RH56
RDAC x 16/1008
RH26
RDAC x 13/1008
RH57
RDAC x 16/1008
RH27
RDAC x 12/1008
RH58
RDAC x 17/1008
RH28
RDAC x 12008
RH59
RDAC x 17/1008
RH29
RDAC x 11/1008
RH60
RDAC x 18/1008
RH30
RDAC x 11/1008
RH61
RDAC x 18/1008
RH31
RDAC x 10/1008
RH62
RDAC x 18/1008
RH63
RDAC x 18/1008
DS200113-14
FIGURE 5. FPD33684B R-DAC Transfer Characteristic (matches Samsung S6C0666) (continued in next figure)
www.national.com
12
FPD33684
Functional Description
(Continued)
RL1
RDAC x 27/1008
RL32
RDAC x 10/1008
RL2
RDAC x 27/1008
RL33
RDAC x 9/1008
RL3
RDAC x 27/1008
RL34
RDAC x 9/1008
RL4
RDAC x 27/1008
RL35
RDAC x 9/1008
RL5
RDAC x 27/1008
RL36
RDAC x 9/1008
RL6
RDAC x 27/1008
RL37
RDAC x 9/1008
RL7
RDAC x 27/1008
RL38
RDAC x 9/1008
RL8
RDAC x 27/1008
RL39
RDAC x 9/1008
RL9
RDAC x 27/1008
RL40
RDAC x 9/1008
RL10
RDAC x 27/1008
RL41
RDAC x 9/1008
RL11
RDAC x 27/1008
RL42
RDAC x 9/1008
RL12
RDAC x 27/1008
RL43
RDAC x 9/1008
RL13
RDAC x 24/1008
RL44
RDAC x 9/1008
RL14
RDAC x 24/1008
RL45
RDAC x 9/1008
RL15
RDAC x 21/1008
RL46
RDAC x 9/1008
RL16
RDAC x 20/1008
RL47
RDAC x 10/1008
RL17
RDAC x 18/1008
RL48
RDAC x 10/1008
RL18
RDAC x 18/1008
RL49
RDAC x 11/1008
RL19
RDAC x 18/1008
RL50
RDAC x 12/1008
RL20
RDAC x 17/1008
RL51
RDAC x 12/1008
RL21
RDAC x 16/1008
RL52
RDAC x 13/1008
RL22
RDAC x 15/1008
RL53
RDAC x 13/1008
RL23
RDAC x 14/1008
RL54
RDAC x 14/1008
RL24
RDAC x 14/1008
RL55
RDAC x 14/1008
RL25
RDAC x 13/1008
RL56
RDAC x 16/1008
RL26
RDAC x 13/1008
RL57
RDAC x 16/1008
RL27
RDAC x 12/1008
RL58
RDAC x 17/1008
RL28
RDAC x 12/1008
RL59
RDAC x 17/1008
RL29
RDAC x 11/1008
RL60
RDAC x 18/1008
RL30
RDAC x 11/1008
RL61
RDAC x 18/1008
RL31
RDAC x 10/1008
RL62
RDAC x 18/1008
RL63
RDAC x 18/1008
DS200113-15
FIGURE 6. FPD33684B R-DAC Transfer Characteristic (matches Samsung S6C0666) (conitnued from previous figure)
13
www.national.com
(Continued)
INPUTS
OUTPUTS
optional
RPI2
384
optional
RPIO2
383
VSS2
382
VDD2
381
ENIO2
.
optional
optional
D22P
.
D22N
.
D21P
.
D21N
.
D20P
.
D20N
.
D12P
.
D12N
.
D11P
.
D11N
.
D10P
.
D10N
.
VCS
.
VDD1
.
UP
.
VGMA10
.
optional
VGMA9
.
optional
VGMA8
.
optional
VGMA7
FPD33684
FPD33684
Functional Description
VGMA6
VHBIAS
.
VGMA5
.
optional
VGMA4
.
optional
VGMA3
.
optional
VGMA2
.
VGMA1
.
optional
VSS1
.
CLKP
.
CLKN
.
LOAD
.
CSTIME
.
POL
.
INVERT
.
D02P
.
D02N
.
D01P
.
D01N
.
D00P
.
D00N
6
ENIO1
5
VSS2
4
VDD2
3
optional
RPO1
2
optional
RPI1
1
Note: This figure represents a FPD33684 die oriented pad side up.
FIGURE 7. FPD33684 I/O Configuration
Packaging
The FPD33684 is available in TCP or as singulated die.
www.national.com
.
.
14
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor
Corporation
Americas
Email: [email protected]
www.national.com
National Semiconductor
Europe
Fax: +49 (0) 180-530 85 86
Email: [email protected]
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
Email: [email protected]
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
FPD33684 Low Power, Low EMI, TFT-LCD Column Driver with RSDS Inputs, 64 Grayshades, and
384 Outputs for XGA/SXGA Applications
LIFE SUPPORT POLICY
Similar pages