AD AD7675AST 16-bit, 100 ksps differential adc Datasheet

a
FEATURES
Throughput: 100 kSPS
INL: 1.5 LSB Max (0.0015% of Full Scale)
16 Bits Resolution with No Missing Codes
S/(N+D): 94 dB Typ @ 45 kHz
THD: –110 dB Typ @ 45 kHz
Differential Input Range: 2.5 V
Both AC and DC Specifications
No Pipeline Delay
Parallel (8 Bits/16 Bits) and Serial 5 V/3 V Interface
SPI™/QSPI™/MICROWIRE™/DSP Compatible
Single 5 V Supply Operation
15 mW Typical Power Dissipation, 15 W @ 100 SPS
Power-Down Mode: 7 W Max
Packages: 48-Lead Quad Flatpack (LQFP),
46-Lead Frame Chip Scale (LFCSP)
Pin-to-Pin Compatible with the AD7660
Replacement of AD676, AD677
APPLICATIONS
CT Scanners
Data Acquisition
Instrumentation
Spectrum Analysis
Medical Instruments
Battery-Powered Systems
Process Control
16-Bit, 100 kSPS,
Differential ADC
AD7675
FUNCTIONAL BLOCK DIAGRAM
AVDD AGND REF REFGND
DVDD
DGND
OVDD
AD7675
OGND
SERIAL
PORT
IN+
SWITCHED
CAP DAC
IN–
SER/PAR
BUSY
16
DATA[15:0]
CLOCK
PD
RESET
PARALLEL
INTERFACE
CS
CONTROL LOGIC AND
CALIBRATION CIRCUITRY
RD
OB/2C
BYTESWAP
CNVST
PulSAR Selection
Type/kSPS
100–250
500–570
1000
Pseudo
Differential
AD7660
AD7650
AD7664
True Bipolar
AD7663
AD7665
AD7671
True Differential
AD7675
AD7676
AD7677
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD7675 is a 16-bit, 100 kSPS, charge redistribution SAR,
fully differential analog-to-digital converter that operates from a
single 5 V power supply. The part contains a high speed 16-bit
sampling ADC, an internal conversion clock, error correction
circuits, and both serial and parallel system interface ports.
1. Excellent INL
The AD7675 has a maximum integral nonlinearity of 1.5 LSB
with no missing 16-bit code.
The AD7675 is hardware factory calibrated and is comprehensively
tested to ensure such ac parameters as signal-to-noise ratio (SNR)
and total harmonic distortion (THD), in addition to the more
traditional dc parameters of gain, offset, and linearity.
3. Fast Throughput
The AD7675 is a 100 kSPS, charge redistribution, 16-bit
SAR ADC with internal error correction circuitry.
It is fabricated using Analog Devices’ high performance, 0.6
micron CMOS process and is available in a 48-lead LQFP or a
tiny 48-lead LFCSP with operation specified from –40°C to +85°C.
2. Superior AC Performances
The AD7675 has a minimum dynamic of 92 dB, 94 dB typical.
4. Single-Supply Operation
The AD7675 operates from a single 5 V supply and typically
dissipates only 17 mW. Its power dissipation decreases
with the throughput to, for instance, only 15 µW at a 100 SPS
throughput. It consumes 7 µW maximum when in power-down.
5. Serial or Parallel Interface
Versatile parallel (8 bits or 16 bits) or 2-wire serial interface
arrangement compatible with either 3 V or 5 V logic.
SPI and QSPI are trademarks of Motorola Inc.
MICROWIRE is a trademark of National Semiconductor Inc.
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© Analog Devices, Inc., 2002
AD7675* PRODUCT PAGE QUICK LINKS
Last Content Update: 02/23/2017
COMPARABLE PARTS
DESIGN RESOURCES
View a parametric search of comparable parts.
• AD7675 Material Declaration
• PCN-PDN Information
EVALUATION KITS
• Quality And Reliability
• AD7675 Evaluation Kit
• Symbols and Footprints
DOCUMENTATION
DISCUSSIONS
Application Notes
View all AD7675 EngineerZone Discussions.
• AN-931: Understanding PulSAR ADC Support Circuitry
• AN-932: Power Supply Sequencing
SAMPLE AND BUY
Data Sheet
Visit the product page to see pricing options.
• AD7675: 16-Bit, 100 kSPS Differential ADC Data Sheet
Product Highlight
TECHNICAL SUPPORT
• 8- to 18-Bit SAR ADCs ... From the Leader in High
Performance Analog
Submit a technical question or find your regional support
number.
REFERENCE MATERIALS
DOCUMENT FEEDBACK
Technical Articles
Submit feedback for this data sheet.
• MS-2210: Designing Power Supplies for High Speed ADC
This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not
trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.
AD7675–SPECIFICATIONS (–40C to +85C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.)
Parameter
Conditions
Min
RESOLUTION
ANALOG INPUT
Voltage Range
Operating Input Voltage
Analog Input CMRR
Input Current
Input Impedance
AC ACCURACY
Signal-to-Noise
Spurious Free Dynamic Range
Total Harmonic Distortion
Signal-to-(Noise+Distortion)
Max
16
VIN+ – VIN–
VIN+, VIN– to AGND
fIN = 10 kHz
100 kSPS Throughput
Unit
Bits
–VREF
–0.1
+VREF
+3
V
V
dB
µA
10
100
µs
kSPS
+1.5
LSB1
Bits
LSB
LSB
LSB
LSB
LSB
79
1
See Analog Input Section
THROUGHPUT SPEED
Complete Cycle
Throughput Rate
DC ACCURACY
Integral Linearity Error
No Missing Codes
Transition Noise
+Full-Scale Error2
–Full-Scale Error2
Zero Error2
Power Supply Sensitivity
Typ
0
–1.5
16
0.35
–22
–22
–8
AVDD = 5 V ± 5%
fIN = 20 kHz
fIN = 45 kHz
fIN = 20 kHz
fIN = 45 kHz
fIN = 20 kHz
fIN = 45 kHz
fIN = 20 kHz
fIN = 45 kHz
fIN = 45 kHz, –60 dB Input
92
104.5
92
–3 dB Input Bandwidth
SAMPLING DYNAMICS
Aperture Delay
Aperture Jitter
Transient Response
Full-Scale Step
REFERENCE
External Reference Voltage Range
External Reference Current Drain
100 kSPS Throughput
± 0.5
94
94
110
110
–110
–110
94
94
34
3.9
+22
+22
+8
–103.5
2
5
8.75
2.3
2.5
35
dB3
dB3
dB3
dB3
dB3
dB3
dB3
dB3
dB3
MHz
ns
ps rms
µs
AVDD – 1.85
V
µA
+0.8
DVDD + 0.3
+1
+1
V
V
µA
µA
DIGITAL INPUTS
Logic Levels
VIL
VIH
IIL
IIH
–0.3
2.0
–1
–1
DIGITAL OUTPUTS
Data Format
Pipeline Delay
VOL
VOH
Parallel or Serial 16-Bit Conversion Results Available
Immediately After Completed Conversion
0.4
OVDD – 0.6
V
V
4.75
4.75
2.7
5.25
5.25
5.254
V
V
V
25
7
mA
µA
µA
mW
µW
µW
+85
°C
POWER SUPPLIES
Specified Performance
AVDD
DVDD
OVDD
Operating Current
AVDD
DVDD5
OVDD5
Power Dissipation5
In Power-Down Mode5
TEMPERATURE RANGE7
Specified Performance
ISINK = 1.6 mA
ISOURCE = –100 µA
5
5
300 kSPS Throughput
3
750
7.5
17
15
100 kSPS Throughput
100 SPS Throughput
TMIN to TMAX
–40
NOTES
1
LSB means Least Significant Bit. With the ± 2.5 V input range, one LSB is 76.3 µV.
2
See Definition of Specifications section. These specifications do not include the error contribution from the external reference.
3
All specifications in dB are referred to a full-scale input FS. Tested with an input signal at 0.5 dB below full-scale unless otherwise specified.
4
The max should be the minimum of 5.25 V and DVDD + 0.3 V.
5
Tested in Parallel Reading Mode.
6
With OVDD below DVDD + 0.3 V and all digital inputs forced to DVDD or DGND, respectively.
7
Contact factory for extended temperature range.
Specifications subject to change without notice.
–2–
REV. A
AD7675
TIMING SPECIFICATIONS (–40C to +85C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.)
Refer to Figures 11 and 12
Convert Pulsewidth
Time Between Conversions
CNVST LOW to BUSY HIGH Delay
BUSY HIGH All Modes Except in Master Serial Read
After Convert Mode
Aperture Delay
End of Conversion to BUSY LOW Delay
Conversion Time
Acquisition Time
RESET Pulsewidth
Symbol
Min
t1
t2
t3
t4
5
10
Typ
Max
Unit
30
1.25
ns
µs
ns
µs
2
t5
t6
t7
t8
t9
10
1.25
8.75
10
Refer to Figures 13, 14, and 15 (Parallel Interface Modes)
CNVST LOW to DATA Valid Delay
DATA Valid to BUSY LOW Delay
Bus Access Request to DATA Valid
Bus Relinquish Time
t10
t11
t12
t13
Refer to Figures 16 and 17 (Master Serial Interface Modes)1
CS LOW to SYNC Valid Delay
CS LOW to Internal SCLK Valid Delay
CS LOW to SDOUT Delay
CNVST LOW to SYNC Delay
SYNC Asserted to SCLK First Edge Delay2
Internal SCLK Period2
Internal SCLK HIGH2
Internal SCLK LOW2
SDOUT Valid Setup Time2
SDOUT Valid Hold Time2
SCLK Last Edge to SYNC Delay2
CS HIGH to SYNC HI-Z
CS HIGH to Internal SCLK HI-Z
CS HIGH to SDOUT HI-Z
BUSY HIGH in Master Serial Read After Convert2
CNVST LOW to SYNC Asserted Delay
SYNC Deasserted to BUSY LOW Delay
t14
t15
t16
t17
t18
t19
t20
t21
t22
t23
t24
t25
t26
t27
t28
t29
t30
Refer to Figures 18 and 19 (Slave Serial Interface Modes)
External SCLK Setup Time
External SCLK Active Edge to SDOUT Delay
SDIN Setup Time
SDIN Hold Time
External SCLK Period
External SCLK HIGH
External SCLK LOW
t31
t32
t33
t34
t35
t36
t37
1.25
45
40
15
5
10
10
10
525
3
25
12
7
4
2
3
40
10
10
10
See Table I
1.25
25
5
3
5
5
25
10
10
18
NOTES
1
In serial interface modes, the SYNC, SCLK, and SDOUT timings are defined with a maximum load C L of 10 pF; otherwise, the load is 60 pF maximum.
2
In serial master read during convert mode. See Table I for serial master read after convert mode.
Specifications subject to change without notice.
REV. A
–3–
ns
ns
µs
µs
ns
µs
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
µs
µs
ns
ns
ns
ns
ns
ns
ns
ns
AD7675
Table I. Serial Clock Timings in Master Read after Convert
DIVSCLK[1]
DIVSCLK[0]
SYNC to SCLK First Edge Delay Minimum
Internal SCLK Period Minimum
Internal SCLK Period Typical
Internal SCLK HIGH Minimum
Internal SCLK LOW Minimum
SDOUT Valid Setup Time Minimum
SDOUT Valid Hold Time Minimum
SCLK Last Edge to SYNC Delay Minimum
Busy High Width Maximum
t18
t19
t19
t20
t21
t22
t23
t24
t28
0
0
0
1
1
0
1
1
Unit
3
25
40
12
7
4
2
3
2
17
50
70
22
21
18
4
60
2.5
17
100
140
50
49
18
30
140
3.5
17
200
280
100
99
18
89
300
5.75
ns
ns
ns
ns
ns
ns
ns
ns
µs
ABSOLUTE MAXIMUM RATINGS 1
1.6mA
Analog Inputs
IN+2, IN–2, REF, REFGND . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . AVDD + 0.3 V to AGND – 0.3 V
Ground Voltage Differences
AGND, DGND, OGND . . . . . . . . . . . . . . . . . . . . . ± 0.3 V
Supply Voltages
AVDD, DVDD, OVDD . . . . . . . . . . . . . . . . –0.3 V to +7 V
AVDD to DVDD, AVDD to OVDD . . . . . . . . . . . . . . ± 7 V
DVDD to OVDD . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Digital Inputs . . . . . . . . . . . . . . . . –0.3 V to DVDD + 0.3 V
Internal Power Dissipation3 . . . . . . . . . . . . . . . . . . . . 700 mW
Internal Power Dissipation4 . . . . . . . . . . . . . . . . . . . . . . 2.5 W
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . 150° C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range
(Soldering 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
IOL
TO OUTPUT
PIN
1.4V
CL
60pF1
500A
IOH
NOTE
1 IN SERIAL INTERFACE MODES, THE SYNC, SCLK, AND
SDOUT TIMINGS ARE DEFINED WITH A MAXIMUM LOAD
CL OF 10pF; OTHERWISE, THE LOAD IS 60pF MAXIMUM.
Figure 1. Load Circuit for Digital Interface Timing, SDOUT,
SYNC, SCLK Outputs, CL = 10 pF
2V
0.8V
tDELAY
NOTES
1
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
See Analog Input section.
3
Specification is for device in free air: 48-Lead LQFP: ␪JA = 91°C/W, ␪JC = 30°C/W.
4
Specification is for device in free air: LFCSP: ␪JA = 26°C/W
tDELAY
2V
0.8V
2V
0.8V
Figure 2. Voltage Reference Levels for Timing
ORDERING GUIDE
Model
Temperature Range
Package Description
AD7675AST
AD7675ASTRL
AD7675ACP
AD7675ACPRL
EVAL-AD7675CB1
EVAL-CONTROL BRD22
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Quad Flatpack (LQFP)
Quad Flatpack (LQFP)
Chip Scale (LFCSP)
Chip Scale (LFCSP)
Evaluation Board
Controller Board
Package
Option
ST-48
ST-48
CP-48
CP-48
NOTES
1
This board can be used as a stand-alone evaluation board or in conjunction with the EVAL-CONTROL BRD2 for evaluation/
demonstration purposes.
2
This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD7675 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
–4–
WARNING!
ESD SENSITIVE DEVICE
REV. A
AD7675
PIN FUNCTION DESCRIPTIONS
Pin No.
Mnemonic
Type
Description
1
2
3, 6, 7,
40–42,
44–48
4
AGND
AVDD
NC
P
P
Analog Power Ground Pin
Input Analog Power Pins. Nominally 5 V.
No Connect
BYTESWAP
DI
5
OB/2C
DI
8
SER/PAR
DI
9, 10
DATA[0:1]
DO
11, 12
DATA[2:3] or
DI/O
Parallel Mode Selection (8-Bit/16-Bit). When LOW, the LSB is output on D[7:0] and the MSB
is output on D[15:8]. When HIGH, the LSB is output on D[15:8] and the MSB is output on D[7:0].
Straight Binary/Binary Two’s Complement. When OB/2C is HIGH, the digital output is
straight binary; when LOW, the MSB is inverted resulting in a two’s complement output
from its internal shift register.
Serial/Parallel Selection Input. When LOW, the parallel port is selected; when HIGH, the
serial interface mode is selected and some bits of the DATA bus are used as a serial port.
Bit 0 and Bit 1 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these outputs are
in high impedance.
When SER/PAR is LOW, these outputs are used as Bit 2 and Bit 3 of the Parallel Port
Data Output Bus.
When SER/PAR is HIGH, EXT/INT is LOW and RDC/SDIN is LOW, which is the serial
master read after convert mode. These inputs, part of the serial port, are used to slow down, if
desired, the internal serial clock that clocks the data output. In the other serial modes, these
pins are high impedance outputs.
When SER/PAR is LOW, this output is used as the Bit 4 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the serial port, is used as a digital select input for
choosing the internal or an external data clock. With EXT/INT tied LOW, the internal clock
is selected on SCLK output. With EXT/INT set to a logic HIGH, output data is synchronized
to an external clock signal connected to the SCLK input.
When SER/PAR is LOW, this output is used as the Bit 5 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the serial port, is used to select the active state of
the SYNC signal. When LOW, SYNC is active HIGH. When HIGH, SYNC is active LOW.
When SER/PAR is LOW, this output is used as the Bit 6 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the serial port, is used to invert the SCLK signal.
It is active in both master and slave mode.
When SER/PAR is LOW, this output is used as the Bit 7 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the serial port, is used as either an external data
input or a read mode selection input depending on the state of EXT/INT.
When EXT/INT is HIGH, RDC/SDIN could be used as a data input to daisy-chain the conversion results from two or more ADCs onto a single SDOUT line. The digital data level on
SDIN is output on DATA with a delay of 16 SCLK periods after the initiation of the read
sequence. When EXT/INT is LOW, RDC/SDIN is used to select the read mode. When RDC/
SDIN is HIGH, the data is output on SDOUT during conversion. When RDC/SDIN is LOW,
the data is output on SDOUT only when the conversion is complete.
Input/Output Interface Digital Power Ground
Input/Output Interface Digital Power. Nominally at the same supply than the supply of the
host interface (5 V or 3 V).
Digital Power. Nominally at 5 V.
Digital Power Ground
DIVSCLK[0:1]
13
DATA[4]
or EXT/INT
DI/O
14
DATA[5]
or INVSYNC
DI/O
15
DATA[6]
or INVSCLK
DI/O
16
DATA[7]
or RDC/SDIN
DI/O
17
18
OGND
OVDD
P
P
19
20
DVDD
DGND
P
P
REV. A
–5–
AD7675
PIN FUNCTION DESCRIPTIONS (continued)
Pin No.
Mnemonic
Type
Description
21
DATA[8]
or SDOUT
DO
22
DATA[9]
or SCLK
DI/O
23
DATA[10]
or SYNC
DO
24
DATA[11]
or RDERROR
DO
25–28
DATA[12:15]
DO
29
BUSY
DO
30
31
32
DGND
RD
CS
P
DI
DI
33
34
RESET
PD
DI
DI
35
CNVST
DI
36
37
38
39
43
AGND
REF
REFGND
IN–
IN+
P
AI
AI
AI
AI
When SER/PAR is LOW, this output is used as the Bit 8 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this output, part of the serial port, is used as a serial data output
synchronized to SCLK. Conversion results are stored in an on-chip register. The AD7675
provides the conversion result, MSB first, from its internal shift register. The DATA
format is determined by the logic level of OB/2C. In serial mode, when EXT/INT is LOW,
SDOUT is valid on both edges of SCLK. In serial mode, when EXT/INT is HIGH: If
INVSCLK is LOW, SDOUT is updated on SCLK rising edge and valid on the next falling
edge. If INVSCLK is HIGH, SDOUT is updated on SCLK falling edge and valid on the next
rising edge.
When SER/PAR is LOW, this output is used as the Bit 9 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this pin, part of the serial port, is used as a serial data clock input
or output, dependent upon the logic state of the EXT/INT Pin. The active edge where the
data SDOUT is updated depends upon the logic state of the INVSCLK Pin.
When SER/PAR is LOW, this output is used as the Bit 10 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this output, part of the serial port, is used as a digital output frame
synchronization for use with the internal data clock (EXT/INT = Logic LOW). When a read
sequence is initiated and INVSYNC is LOW, SYNC is driven HIGH and remains HIGH
while SDOUT output is valid. When a read sequence is initiated and INVSYNC is HIGH,
SYNC is driven LOW and remains LOW while SDOUT output is valid.
When SER/PAR is LOW, this output is used as the Bit 11 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH and EXT/INT is HIGH, this output, part of the serial port, is used
as an incomplete read error flag. In slave mode, when a data read is started and not complete
when the following conversion is complete, the current data is lost and RDERROR is pulsed high.
Bit 12 to Bit 15 of the Parallel Port Data output bus. These pins are always outputs regardless
of the state of SER/PAR.
Busy Output. Transitions HIGH when a conversion is started, and remains HIGH until the
conversion is complete and the data is latched into the on-chip shift register. The falling edge
of BUSY could be used as a data ready clock signal.
Must Be Tied to Digital Ground
Read Data. When CS and RD are both LOW, the interface parallel or serial output bus is enabled.
Chip Select. When CS and RD are both LOW, the interface parallel or serial output bus is
enabled. CS is also used to gate the external serial clock.
Reset Input. When set to a logic HIGH, reset the AD7675. Current conversion if any is aborted.
Power-Down Input. When set to a logic HIGH, power consumption is reduced and conversions are inhibited after the current one is completed.
Start Conversion. If CNVST is HIGH when the acquisition phase (t8) is complete, the next
falling edge on CNVST puts the internal sample/hold into the hold state and initiates a
conversion. This mode is the most appropriate if low sampling jitter is desired. If CNVST is
LOW when the acquisition phase (t8) is complete, the internal sample/hold is put into the hold
state and a conversion is immediately started.
Must Be Tied to Analog Ground
Reference Input Voltage
Reference Input Analog Ground
Differential Negative Analog Input
Differential Positive Analog Input
NOTES
AI = Analog Input
DI = Digital Input
DI/O = Bidirectional Digital
DO = Digital Output
P = Power
–6–
REV. A
AD7675
PIN CONFIGURATION
REF
REFGND
IN–
NC
NC
NC
IN+
NC
NC
NC
NC
NC
48-Lead LQFP
(ST-48)
48 47 46 45 44 43 42 41 40 39 38 37
AGND
1
AVDD 2
PIN 1
IDENTIFIER
36
AGND
35
NC 3
34
CNVST
PD
BYTESWAP 4
33
RESET
OB/2C 5
NC 6
32
CS
31
30
RD
DGND
SER/PAR 8
D0 9
29
BUSY
28
D15
D1 10
27
D14
D2/DIVSCLK[0] 11
26
D13
D3/DIVSCLK[1] 12
25
D12
AD7675
TOP VIEW
(Not to Scale)
NC 7
D11/RDERROR
D10/SYNC
D9/SCLK
D8/SDOUT
DGND
DVDD
OVDD
OGND
D7/RDC/SDIN
D6/INVSCLK
13 14 15 16 17 18 19 20 21 22 23 24
D4/EXT/INT
D5/INVSYNC
NC = NO CONNECT
DEFINITION OF SPECIFICATIONS
EFFECTIVE NUMBER OF BITS (ENOB)
INTEGRAL NONLINEARITY ERROR (INL)
ENOB is a measurement of the resolution with a sine wave
input. It is related to S/(N+D) by the following formula:
Integral Nonlinearity is the maximum deviation of a straight line
drawn through the transfer function of the actual ADC. The
deviation is measured from the middle of each code.
DIFFERENTIAL NONLINEARITY ERROR (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It
is often specified in terms of resolution for which no missing
codes are guaranteed.
(
[
ENOB = S / N + D
]
dB
)
– 1.76 / 6.02
and is expressed in bits.
TOTAL HARMONIC DISTORTION (THD)
THD is the ratio of the rms sum of the first five harmonic
components to the rms value of a full-scale input signal and is
expressed in decibels.
+FULL-SCALE ERROR
The last transition (from 011 . . . 10 to 011 . . . 11 in two’s
complement coding) should occur for an analog voltage 1 1/2 LSB
below the nominal +full scale (+2.499886 V for the ± 2.5 V range).
The +full-scale error is the deviation of the actual level of the
last transition from the ideal level.
SIGNAL-TO-NOISE RATIO (SNR)
–FULL-SCALE ERROR
SIGNAL-TO-(NOISE + DISTORTION) RATIO (S/[N+D])
The first transition (from 100 . . . 00 to 100 . . . 01 in two’s
complement coding) should occur for an analog voltage 1/2 LSB
above the nominal –full scale (–2.499962 V for the ± 2.5 V range).
The –full-scale error is the deviation of the actual level of the
last transition from the ideal level.
S/(N+D) is the ratio of the rms value of the actual input signal
to the rms sum of all other spectral components below the
Nyquist frequency, including harmonics but excluding dc. The
value for S/(N+D) is expressed in decibels.
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
APERTURE DELAY
BIPOLAR ZERO ERROR
The bipolar zero error is the difference between the ideal midscale
input voltage (0 V) and the actual voltage producing the midscale
output code.
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the CNVST input to when
the input signal is held for a conversion.
TRANSIENT RESPONSE
SPURIOUS FREE DYNAMIC RANGE (SFDR)
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
REV. A
The time required for the AD7675 to achieve its rated accuracy
after a full-scale step function is applied to its input.
–7–
AD7675 –Typical Performance Characteristics
1.00
16000
0.75
14000
0.50
12000
0.25
10000
COUNTS
INL – LSB
14687
0.00
8000
–0.25
6000
–0.50
4000
–0.75
2000
–1.00
0000
0
16384
32768
CODE
49152
65536
8246 8118
8000
810
0
0
0
0
0
7FF8 7FF9 7FFA 7FFB 7FFC 7FFD 7FFE 7FFF 8000 8001 8002
CODE IN HEXA
16
14
NUMBER OF UNITS
7000
6000
COUNTS
0
18
9000
5000
4000
3000
12
10
8
6
4
2000
2
1000
0
0000
0
0
6
14
0
0
0
0
–1.0
7FFB 7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004
CODE IN HEXA
–0.8
–0.6
–0.4
NEGATIVE INL – LSB
–0.2
0.0
TPC 5. Typical Negative INL Distribution (40 Units)
TPC 2. Histogram of 16,384 Conversions of a DC Input at
the Code Transition
0
16
–20
AMPLITUDE – dB of Full Scale
18
14
NUMBER OF UNITS
0
TPC 4. Histogram of 16,384 Conversions of a DC Input at
the Code Center
TPC 1. Integral Nonlinearity vs. Code
12
10
8
6
4
fS = 100 kSPS
fIN = 45.01kHz
SNR = 94dB
THD = –110dB
SFDR = 110dB
SINAD = 93.9dB
–40
–60
–80
–100
–120
–140
–160
2
0
887
0
–180
0
0.2
0.4
0.6
POSITIVE INL – LSB
0.8
1.0
TPC 3. Typical Positive INL Distribution (40 Units)
0
10
20
30
FREQUENCY – kHz
40
50
TPC 6. FFT Plot
–8–
REV. A
AD7675
100
16.0
50
OVDD = 2.7V @ 85C
15.5
15.0
SNR
14.5
85
SINAD
80
t12 DELAY – ns
90
40
ENOB – Bits
SNR AND S/[N+D] – dB
95
ENOB
OVDD = 5.0V @ 85C
20
OVDD = 5.0V @ 25C
10
13.5
70
1
13.0
1000
10
100
FREQUENCY – kHz
0
0
50
100
CL – pF
200
150
TPC 7. SNR, S/(N+D), and ENOB vs. Frequency
TPC 10. Typical Delay vs. Load Capacitance CL
96
100k
SNR
10k
SINAD
OPERATING CURRENTS – A
SNR (REFERRED TO FULL SCALE) – dB
30
14.0
75
94
92
90
1k
AVDD
100
DVDD
10
1
OVDD
0.1
0.01
88
–60
–50
–40
–30
–20
INPUT LEVEL – dB
–10
0.001
10
0
TPC 8. SNR and S/(N+D) vs. Input Level
96
–104
POWER-DOWN OPERATING CURRENTS – nA
–106
90
–108
84
–55
–110
THD
–35
–15
0
25
45
65
TEMPERATURE – C
85
105
TPC 9. SNR, THD vs. Temperature
REV. A
1k
10k
SAMPLING RATE – SPS
100k
250
THD – dB
93
87
100
TPC 11. Operating Currents vs. Sample Rate
SNR
SNR – dB
OVDD = 2.7V @ 25C
–112
125
DVDD
200
150
100
50
0
–55
AVDD
OVDD
–35
–15
5
25
45
65
85
105
TEMPERATURE – C
TPC 12. Power-Down Operating Currents vs. Temperature
–9–
AD7675
During the acquisition phase, terminals of the array tied to the
comparator’s input are connected to AGND via SW+ and SW–.
All independent switches are connected to the analog inputs.
Thus, the capacitor arrays are used as sampling capacitors and
acquire both analog signals.
5
4
3
2
–FS
When the acquisition phase is complete and the CNVST input
goes or is low, a conversion phase is initiated. When the conversion phase begins, SW+ and SW– are opened first. The two
capacitor arrays are then disconnected from the inputs and
connected to the REFGND input. Therefore, the differential
voltage between the output of IN+ and IN– captured at the
end of the acquisition phase is applied to the comparator inputs,
causing the comparator to become unbalanced.
LSB
1
0
–1
OFFSET
–2
+FS
–3
–4
–5
–55
–35
–15
–5
15
35
55
75
TEMPERATURE – C
95
115
135
By switching each element of the capacitor array between
REFGND or REF, the comparator input varies by binary
weighted voltage steps (VREF/2, VREF/4 . . . VREF/65536). The
control logic toggles these switches, starting with the MSB first,
in order to bring the comparator back into a balanced condition.
After the completion of this process, the control logic generates
the ADC output code and brings BUSY output low.
TPC 13. Drift vs. Temperature
CIRCUIT INFORMATION
The AD7675 is a fast, low power, single-supply, precise 16-bit
analog-to-digital converter (ADC). The AD7675 is capable of
converting 100,000 samples per second (100 kSPS) and allows
power saving between conversions. When operating at 100 SPS,
for example, it consumes typically only 15 µW. This feature
makes the AD7675 ideal for battery-powered applications.
Transfer Functions
Using the OB/2C digital input, the AD7675 offers two output
codings: straight binary and two’s complement. The ideal transfer characteristic for the AD7675 is shown in Figure 4.
ADC CODE – Straight Binary
The AD7675 provides the user with an on-chip track/hold,
successive approximation ADC that does not exhibit any pipeline or latency, making it ideal for multiple multiplexed channel
applications.
The AD7675 can be operated from a single 5 V supply and be
interfaced to either 5 V or 3 V digital logic. It is housed in a
48-lead LQFP package that combines space savings and allows
flexible configurations as either serial or parallel interface. The
AD7675 is pin-to-pin compatible with the AD7660.
111...111
111...110
111...101
000...010
CONVERTER OPERATION
000...001
The AD7675 is a successive approximation analog-to-digital
converter based on a charge redistribution DAC. Figure 3 shows
the simplified schematic of the ADC. The capacitive DAC consists of two identical arrays of 16 binary-weighted capacitors that
are connected to the two comparator inputs.
000...000
–FS
–FS + 1 LSB
+FS – 1 LSB
–FS + 0.5 LSB
+FS – 1.5 LSB
ANALOG INPUT
Figure 4. ADC Ideal Transfer Function
IN+
SWITCHES
CONTROL
MSB
32,768C 16,384C
LSB
4C
2C
C
C
SW+
BUSY
REF
COMP
CONTROL
LOGIC
OUTPUT
CODE
REFGND
32,768C 16,384C
4C
2C
C
C
LSB
MSB
SW–
CNVST
IN–
Figure 3. ADC Simplified Schematic
–10–
REV. A
AD7675
DVDD
ANALOG
SUPPLY
(5V)
100
DIGITAL SUPPLY
(3.3V OR 5V)
NOTE 6
+
+
100nF
10F
ADR421
AVDD
10F
AGND
100nF
DGND
100nF
DVDD
REF
2.5V REF
1M
C
50k + REF
NOTE 1
100nF
OVDD
+
10F
OGND
SERIAL PORT
SCLK
1F
NOTE 2
SDOUT
REFGND
NOTE 3
50
NOTE 4
ANALOG INPUT+
BUSY
–
U1
+
AD8021
15
CC
CNVST
IN+
C/P/DSP
50
D
NOTE 7
2.7nF
AD7675
NOTE 5
OB/2C
SER/PAR
DVDD
50
NOTE 4
ANALOG INPUT–
–
U2
+
AD8021
CS
15
CC
IN–
CLOCK
RD
BYTESWAP
2.7nF
RESET
NOTE 5
PD
NOTES
1. SEE VOLTAGE REFERENCE INPUT SECTION.
2. WITH THE RECOMMENDED VOLTAGE REFERENCES, CREF IS 47F. SEE CHAPTER VOLTAGE REFERENCE INPUT SECTION
3. OPTIONAL CIRCUITRY FOR HARDWARE GAIN CALIBRATION.
4. THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION.
5. SEE ANALOG INPUT SECTION.
6. OPTION, SEE POWER SUPPLY SECTION
7. OPTIONAL LOW JITTER CNVST, SEE CONVERSION CONTROL SECTION.
Figure 5. Typical Connection Diagram. (± 2.5 V Range Shown)
the input buffer’s (U1) or (U2) supplies are different from
TYPICAL CONNECTION DIAGRAM
AVDD. In such a case, an input buffer with a short-circuit
current limitation can be used to protect the part.
Figure 5 shows a typical connection diagram for the AD7675.
Different circuitry shown on this diagram is optional and is
discussed below.
Analog Inputs
Figure 6 shows a simplified analog input section of the AD7675.
This analog input structure is a true differential structure. By
using these differential inputs, signals common to both inputs
are rejected, as shown in Figure 7, which represents the typical
CMRR over frequency.
AVDD
85
80
R+ = 684
75
IN+
CS
70
IN–
CMRR – dB
CS
R– = 684
65
60
55
AGND
50
Figure 6. Simplified Analog Input
The diodes shown in Figure 6 provide ESD protection for the
inputs. Care must be taken to ensure that the analog input signal never exceeds the absolute ratings on these inputs. This will
cause these diodes to become forward-biased and start conducting
current. These diodes can handle a forward-biased current of
120 mA maximum. This condition could eventually occur when
REV. A
–11–
45
40
1k
10k
100k
1M
10M
FREQUENCY – Hz
Figure 7. Analog Input CMRR vs. Frequency
AD7675
one-pole, low-pass filter made by R+, R–, and CS. The SNR
degradation due to the amplifier is:
During the acquisition phase for ac signals, the AD7675 behaves
like a one-pole RC filter consisting of the equivalent resistance
R+, R–, and CS. The resistors R+ and R– are typically 684 Ω
and are lumped components made up of some serial resistors
and the on resistance of the switches. The capacitor CS is typically
60 pF and is mainly the ADC sampling capacitor. This one pole
filter with a typical –3 dB cutoff frequency of 3.9 MHz reduces
undesirable aliasing effect and limits the noise coming from
the inputs.
SNR LOSS
f –3 dB is the –3 dB input bandwidth of the AD7675 (3.9 MHz)
or the cutoff frequency of the input filter if any is used.
N is the noise factor of the amplifier (1 if in buffer configuration)
eN is the equivalent input noise voltage of the op amp in
nV/(Hz)1/2.
For instance, in the case of a driver with an equivalent input
noise of 2 nV/√Hz like the AD8021 and configured as a buffer,
thus with a noise gain of +1, the SNR degrades by only 0.04 dB
with the filter in Figure 5, and 0.07 dB without.
• The driver needs to have a THD performance suitable to
that of the AD7675.
Single to Differential Driver
For applications using unipolar analog signals, a single-ended to
differential driver will allow for a differential input into the part.
The schematic is shown in Figure 8.
AD8021
CC
The AD8132 or the AD8138 could also be used to generate a differential signal from a single-ended signal. When using the AD8138
with the filter in Figure 5, the SNR degrades by only 0.9 dB.
IN+
590
590
590
AD8021
CC
The AD829 is another alternative where high frequency (above
100 kHz) performances are not required. In gain of 1, it requires
an 82 pF compensation capacitor.
AD7675
IN–
U2
The AD8021 meets these requirements and is usually appropriate for almost all applications. The AD8021 needs an external
compensation capacitor of 10 pF. This capacitor should have
good linearity as an NPO ceramic or mica type.
The AD8022 could also be used where dual version is needed
and gain of 1 is used.
U1
590
2.5V REF





where
Because the input impedance of the AD7675 is very high, the
AD7675 can be driven directly by a low impedance source
without gain error. That allows users to put, as shown in
Figure 5, an external one-pole RC filter between the output
of the amplifier output and the ADC analog inputs to even
further improve the noise filtering done by the AD7675 analog
input circuit. However, the source impedance has to be kept
low because it affects the ac performances, especially the total
harmonic distortion. The maximum source impedance depends
on the amount of total harmonic distortion (THD) that can be
tolerated. The THD degrades proportionally to the source
impedance.
ANALOG INPUT
(UNIPOLAR)


28
= 20LOG 
π
 784 + f –3 dB ( N e N )2

4
REF
The AD8610 is also another option where low bias current is
needed in low frequency applications.
2.5V REF
Figure 8. Single-Ended-to-Differential Driver Circuit
The AD8519, OP162, or the OP184 could also be used.
This configuration, when provided an input signal of 0 to VREF,
will produce a differential ± 2.5 V with a common mode at 1.25 V.
Voltage Reference Input
If the application can tolerate more noise, the AD8138 can be used.
The voltage reference input REF of the AD7675 has a dynamic
input impedance. Therefore, it should be driven by a low
impedance source with an efficient decoupling between REF
and REFGND inputs. This decoupling depends on the choice
of the voltage reference but usually consists of a 1 µF ceramic
capacitor and a low ESR tantalum capacitor connected to the
REF and REFGND inputs with minimum parasitic inductance. 47 µF is an appropriate value for the tantalum capacitor
when used with one of the recommended reference voltages:
Driver Amplifier Choice
Although the AD7675 is easy to drive, the driver amplifier needs
to meet at least the following requirements:
• The driver amplifier and the AD7675 analog input circuit
have to be able to settle for a full-scale step of the capacitor array at a 16-bit level (0.0015%). In the amplifier’s data
sheet, the settling at 0.1% or 0.01% is more commonly specified. It could significantly differ from the settling time at
16-bit level and, therefore, it should be verified prior to the
driver selection. The tiny op amp AD8021, which combines
ultra low noise and a high gain bandwidth, meets this settling
time requirement even when used with a high gain up to 13.
• The noise generated by the driver amplifier needs to be kept
as low as possible in order to preserve the SNR and transition noise performance of the AD7675. The noise coming
from the driver is filtered by the AD7675 analog input circuit
The AD7675 uses an external 2.5 V voltage reference.
• The low noise, low temperature drift ADR421 and AD780
voltage references
• The low power ADR291 voltage reference
• The low cost AD1582 voltage reference
For applications using multiple AD7675s, it is more effective to
buffer the reference voltage with a low noise, very stable op amp
like the AD8031.
–12–
REV. A
AD7675
Care should also be taken with the reference temperature coefficient of the voltage reference which directly affects the full-scale
accuracy if this parameter matters. For instance, a ± 15 ppm/°C
tempco of the reference changes the full scale by ± 1 LSB/°C.
100k
POWER DISSIPATION – W
10k
VREF , as mentioned in the specification table, could be increased
to AVDD – 1.85 V. The benefit here is the increased SNR
obtained as a result of this increase. Since the input range is
defined in terms of VREF, this would essentially increase the
range to make it a ± 3 V input range with an AVDD above
4.85 V. The theoretical improvement as a result of this increase
in reference is 1.58 dB (20 log [3/2.5]). Due to the theoretical
quantization noise, however, the observed improvement is
approximately 1 dB. The AD780 can be selected with a 3 V
reference voltage.
1k
100
10
1
0.1
10
100
1k
10k
100k
1M
SAMPLING RATE – SPS
Power Supply
The AD7675 uses three sets of power supply pins: an analog
5 V supply AVDD, a digital 5 V core supply DVDD, and a
digital input/output interface supply OVDD. The OVDD
supply allows direct interface with any logic working between
2.7 V and DVDD + 0.3 V. To reduce the number of supplies
needed, the digital core (DVDD) can be supplied through a
simple RC filter from the analog supply as shown in
Figure 5. The AD7675 is independent of power supply
sequencing once OVDD does not exceed DVDD by more than
0.3 V, and thus free from supply voltage induced latchup.
Additionally, it is very insensitive to power supply variations
over a wide frequency range as shown in Figure 9.
Figure 10. Power Dissipation vs. Sample Rate
CONVERSION CONTROL
Figure 11 shows the detailed timing diagrams of the conversion
process. The AD7675 is controlled by the signal CNVST, which
initiates conversion. Once initiated, it cannot be restarted or
aborted, even by the power-down input PD, until the conversion is complete. The CNVST signal operates independently of
CS and RD signals.
t2
t1
CNVST
75
70
BUSY
t4
PSRR – dB
65
t3
MODE
ACQUIRE
CONVERT
ACQUIRE
t7
t8
CONVERT
55
50
Figure 11. Basic Conversion Timing
45
For true sampling applications, the recommended operation of
the CNVST signal is as follows:
40
35
1k
10k
100k
1M
10M
FREQUENCY – Hz
Figure 9. PSRR vs. Frequency
POWER DISSIPATION
The AD7675 automatically reduces its power consumption at
the end of each conversion phase. During the acquisition phase,
the operating currents are very low, which allows a significant
power saving when the conversion rate is reduced as shown in
Figure 10. This feature makes the AD7675 ideal for very low
power battery applications.
CNVST must be held high from the previous falling edge of
BUSY, and during a minimum delay corresponding to the
acquisition time t8; then, when CNVST is brought low, a
conversion is initiated and BUSY signal goes high until the
completion of the conversion. Although CNVST is a digital
signal, it should be designed with this special care with fast,
clean edges and levels, with minimum overshoot and undershoot or ringing.
For applications where the SNR is critical, the CNVST signal should
have a very low jitter. Some solutions to achieve that are to use a
dedicated oscillator for CNVST generation or, at least, to clock
it with a high frequency low jitter clock, as shown in Figure 5.
It should be noted that the digital interface remains active even
during the acquisition phase. To reduce the operating digital
supply currents even further, the digital inputs need to be driven
close to the power rails (i.e., DVDD and DGND) and OVDD
should not exceed DVDD by more than 0.3 V.
REV. A
t6
t5
60
–13–
AD7675
PARALLEL INTERFACE
t9
The AD7675 is configured to use the parallel interface (Figure 13)
when the SER/PAR is held low. The data can be read either
after each conversion, which is during the next acquisition
phase, or during the following conversion as shown, respectively,
in Figure 14 and Figure 15. When the data is read during the
conversion, however, it is recommended that it be read-only
during the first half of the conversion phase. That avoids any
potential feedthrough between voltage transients on the digital
interface and the most critical analog conversion circuitry.
RESET
BUSY
DATA
t8
CS
CNVST
RD
Figure 12. RESET Timing
For other applications, conversions can be automatically initiated. If CNVST is held low when BUSY is low, the AD7675
controls the acquisition phase and then automatically initiates a
new conversion. By keeping CNVST low, the AD7675 keeps
the conversion process running by itself. It should be noted that
the analog input has to be settled when BUSY goes low. Also, at
power-up, CNVST should be brought low once to initiate the
conversion process. In this mode, the AD7675 could sometimes
run slightly faster than the guaranteed limit of 100 kSPS.
BUSY
DATA
BUS
t12
CS = 0
t1
CNVST
t1
CNVST,
RD
The AD7675 has a versatile digital interface; it can be interfaced
with the host system by using either a serial or parallel interface.
The serial interface is multiplexed on the parallel data bus. The
AD7675 digital interface also accommodates both 3 V or 5 V
logic by simply connecting the OVDD supply pin of the AD7675
to the host system interface digital supply. Finally, by using the
OB/2C input pin, either two’s complement or straight binary
coding can be used.
CS = RD = 0
t13
Figure 14. Slave Parallel Data Timing for Reading
(Read after Convert)
DIGITAL INTERFACE
The two signals CS and RD control the interface. When at least
one of these signals is high, the interface outputs are in high
impedance. Usually, CS allows the selection of each AD7675 in
multicircuits applications and is held low in a single AD7675
design. RD is generally used to enable the conversion result on
the data bus.
CURRENT
CONVERSION
t4
BUSY
t3
PREVIOUS
CONVERSION
DATA
BUS
t12
t13
Figure 15. Slave Parallel Data Timing for Reading (Read
During Convert)
The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 16, the LSB byte is output on D[7:0] and
the MSB is output on D[15:8] when BYTESWAP is low. When
BYTESWAP is high, the LSB and MSB bytes are swapped and
the LSB is output on D[15:8] and the MSB is output on D[7:0].
By connecting BYTESWAP to an address line, the 16-bit data
can be read in two bytes on either D[15:8] or D[7:0].
t10
t3
DATA
BUS
CS
t4
BUSY
t11
PREVIOUS CONVERSION DATA
RD
NEW DATA
BYTE
Figure 13. Master Parallel Data Timing for Reading
(Continuous Read)
PINS D[15:8]
HI-Z
HIGH BYTE
t12
PINS D[7:0]
HI-Z
LOW BYTE
LOW BYTE
t12
HIGH BYTE
HI-Z
t13
HI-Z
Figure 16. 8-Bit Parallel Interface
–14–
REV. A
AD7675
serial data is valid. The serial clock SCLK and the SYNC signal
can be inverted if desired. The output data is valid on both the
rising and falling edge of the data clock. Depending on RDC/
SDIN input, the data can be read after each conversion, or
during the following conversion. Figure 17 and Figure 18 show
the detailed timing diagrams of these two modes.
SERIAL INTERFACE
The AD7675 is configured to use the serial interface when the
SER/PAR is held high. The AD7675 outputs 16 bits of data,
MSB first, on the SDOUT pin. This data is synchronized with
the 16 clock pulses provided on the SCLK pin.
MASTER SERIAL INTERFACE
Internal Clock
Usually, because the AD7675 has a longer acquisition phase
than the conversion phase, the data is read immediately after
conversion. That makes the mode master, read after conversion,
the most recommended serial mode when it can be used.
The AD7675 is configured to generate and provide the serial
data clock SCLK when the EXT/INT pin is held low. The AD7675
also generates a SYNC signal to indicate to the host when the
RDC/SDIN = 0
EXT/INT = 0
CS, RD
INVSCLK = INVSYNC = 0
t3
CNVST
t28
BUSY
t30
t29
t25
SYNC
t18
t19
t14
t20
t24
t21
t26
1
SCLK
2
3
14
15
16
t15
t27
X
SDOUT
t16
D15
D14
D2
D1
D0
t23
t22
Figure 17. Master Serial Data Timing for Reading (Read after Convert)
RDC/SDIN = 1
EXT/INT = 0
CS, RD
INVSCLK = INVSYNC = 0
t1
CNVST
t3
BUSY
t17
t25
SYNC
t14
t19
t20 t21
t15
SCLK
1
t24
2
3
14
15
t18
X
SDOUT
t16
t27
D15
t22
t26
16
D14
D2
D1
D0
t23
Figure 18. Master Serial Data Timing for Reading (Read Previous Conversion during Convert)
REV. A
–15–
AD7675
In read-after-conversion mode, unlike in other modes, it should
be noted that the signal BUSY returns low after the 16 data bits
are pulsed out and not at the end of the conversion phase, which
results in a longer BUSY width.
the conversion phase. For this reason, it is recommended that when
an external clock is being provided, it is a discontinuous clock
that is toggling only when BUSY is low or, more importantly,
that it does not transition during the latter half of BUSY high.
In read-during-conversion mode, the serial clock and data toggle
at appropriate instances, which minimizes potential feedthrough
between digital activity and the critical conversion decisions.
External Discontinuous Clock Data Read after Conversion
To accommodate slow digital hosts, the serial clock can be
slowed down by using DIVSCLK.
SLAVE SERIAL INTERFACE
External Clock
The AD7675 is configured to accept an externally supplied
serial data clock on the SCLK Pin when the EXT/INT Pin is
held high. In this mode, several methods can be used to read the
data. The external serial clock is gated by CS and the data are
output when both CS and RD are low. Thus, depending on
CS, the data can be read after each conversion or during the
following conversion. The external clock can be either a continuous or discontinuous clock. A discontinuous clock can be
either normally high or normally low when inactive. Figure 19
and Figure 20 show the detailed timing diagrams of these methods. Usually, because the AD7675 has a longer acquisition
phase than the conversion phase, the data are read immediately
after conversion.
While the AD7675 is performing a bit decision, it is important
that voltage transients not occur on digital input/output pins or
degradation of the conversion result could occur. This is particularly important during the second half of the conversion phase
because the AD7675 provides error-correction circuitry that can
correct for an improper bit decision made during the first half of
This mode is the most recommended of the serial slave modes.
Figure 19 shows the detailed timing diagrams of this method.
After a conversion is complete, indicated by BUSY returning
low, the result of this conversion can be read while both CS and
RD are low. The data is shifted out, MSB first, with 16 clock
pulses and is valid on both the rising and falling edge of the clock.
One of the advantages of this method is that the conversion
performance is not degraded because there are no voltage transient on the digital interface during the conversion process.
Another advantage is the ability to read the data at any speed up
to 40 MHz, which accommodates both slow digital host interface and the fastest serial reading.
Finally, in this mode only, the AD7675 provides a “daisy chain”
feature using the RDC/SDIN input pin for cascading multiple
converters together. This feature is useful for reducing component count and wiring connections when it is desired as it is, for
instance, in isolated multiconverters applications.
An example of the concatenation of two devices is shown in
Figure 21. Simultaneous sampling is possible by using a common CNVST signal. It should be noted that the RDC/SDIN
input is latched on the opposite edge of SCLK of the one used
to shift out the data on SDOUT. Hence, the MSB of the
“upstream” converter just follows the LSB of the “downstream”
converter on the next SCLK cycle.
RD = 0
INVSCLK = 0
EXT/INT = 1
CS
BUSY
t36
SCLK
t35
t37
1
2
t31
3
14
15
16
17
18
t32
SDOUT
X
t16
D15
D14
D13
D1
D0
X15
X14
X14
X13
X1
X0
Y15
Y14
t34
SDIN
X15
t33
Figure 19. Slave Serial Data Timing for Reading (Read after Convert)
–16–
REV. A
AD7675
16-bit wide interface or with a general purpose serial port or I/O
ports on a microcontroller. A variety of external buffers can be
used with the AD7675 to prevent digital noise from coupling
into the ADC. The following sections illustrate the use of the
AD7675 with an SPI-equipped microcontroller, and the
ADSP-21065L and ADSP-218x signal processors.
External Clock Data Read During Conversion
Figure 20 shows the detailed timing diagrams of this method.
During a conversion, while both CS and RD are low, the result
of the previous conversion can be read. The data is shifted out,
MSB first, with 16 clock pulses, and is valid on both rising and
falling edges of the clock. The 16 bits have to be read before the
current conversion is complete. If that is not done, RDERROR is
pulsed high and can be used to interrupt the host interface to
prevent incomplete data reading. There is no “daisy chain”
feature in this mode, and RDC/SDIN input should always be
tied either high or low.
SPI Interface (MC68HC11)
To reduce performance degradation due to digital activity, a fast
discontinuous clock of 18 MHz at least is recommended to ensure
that all the bits are read during the first half of the conversion
phase. For this reason, this mode is more difficult to use.
MICROPROCESSOR INTERFACING
The AD7675 is ideally suited for traditional dc measurement
applications supporting a microprocessor, and ac signal processing applications interfacing to a digital signal processor. The
AD7675 is designed to interface either with a parallel 8-bit or
Figure 22 shows an interface diagram between the AD7675 and
an SPI-equipped microcontroller like the MC68HC11. To
accommodate the slower speed of the microcontroller, the
AD7675 acts as a slave device and data must be read after conversion. This mode also allows the “daisy chain” feature. The
convert command could be initiated in response to an internal
timer interrupt. The reading of output data, one byte at a time if
necessary, could be initiated in response to the end-of-conversion
signal (BUSY going low) using an interrupt line of the microcontroller. The Serial Peripheral Interface (SPI) on the MC68HC11
is configured for master mode (MSTR) = 1, Clock Polarity Bit
(CPOL) = 0, Clock Phase Bit (CPHA) = 1 and SPI interrupt
enable (SPIE) = 1 by writing to the SPI Control Register (SPCR).
The IRQ is configured for edge-sensitive-only operation
(IRQE = 1 in OPTION register).
RD = 0
INVSCLK = 0
EXT/INT = 1
CS
CNVST
BUSY
t3
t35
t36
SCLK
t37
1
2
t31
SDOUT
3
14
15
16
t32
X
D15
D14
D13
D1
D0
t16
Figure 20. Slave Serial Data Timing for Reading (Read Previous Conversion during Convert)
BUSY
OUT
BUSY
BUSY
AD7675 #2
AD7675 #1
(DOWNSTREAM)
(UPSTREAM)
RDC/SDIN
SDOUT
RDC/SDIN
CNVST
SDOUT
DATA
OUT
CNVST
CS
CS
SCLK
SCLK
SCLK IN
CS IN
CNVST IN
Figure 21. Two AD7675s in a “Daisy Chain” Configuration
REV. A
–17–
AD7675
ground planes should be joined in only one place, preferably
underneath the AD7675, or, at least, as close as possible to the
AD7675. If the AD7675 is in a system where multiple devices
require analog to digital ground connections, the connection
should still be made at one point only, a star ground point
that should be established as close as possible to the AD7675.
DVDD
MC68HC11*
AD7675*
SER/PAR
EXT/INT
CS
BUSY
RD
SDOUT
INVSCLK
CNVST
SCLK
IRQ
MISO/SDI
SCK
I/O PORT
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 22. Interfacing the AD7675 to SPI Interface
ADSP-21065L in Master Serial Interface
As shown in Figure 23, the AD7675 can be interfaced to the
ADSP-21065L using the serial interface in master mode without any
glue logic required. This mode combines the advantages of reducing
the wire connections and the ability to read the data during or after
conversion maximum speed transfer (DIVSCLK[0:1] both low).
The AD7675 is configured for the internal clock mode (EXT/
INT low) and acts, therefore, as the master device. The convert
command can be generated by either an external low jitter oscillator or, as shown, by a FLAG output of the ADSP-21065L or
by a frame output TFS of one serial port of the ADSP-21065L
that can be used like a timer. The serial port on the ADSP21065L is configured for external clock (IRFS = 0), rising edge
active (CKRE = 1), external late framed sync signals (IRFS = 0,
LAFS = 1, RFSR = 1) and active high (LRFS = 0). The serial
port of the ADSP-21065L is configured by writing to its receive
control register (SRCTL)—see ADSP-2106x SHARC User’s
Manual. Because the serial port within the ADSP-21065L will
be seeing a discontinuous clock, an initial word reading has to
be done after the ADSP-21065L has been reset to ensure that
the serial port is properly synchronized to this clock during each
following data read operation.
DVDD
ADSP-21065L*
AD7675*
SHARC
RDC/SDIN
EXT/INT
CS
INVSYNC
SYNC
SDOUT
SCLK
CNVST
The power supply lines to the AD7675 should use as large a
trace as possible to provide low impedance paths and reduce the
effect of glitches on the power supply lines. Good decoupling is
also important to lower the supply’s impedance presented to
the AD7675 and reduce the magnitude of the supply spikes.
Decoupling ceramic capacitors, typically 100 nF, should be
placed on each power supply’s pins, AVDD, DVDD, and OVDD,
close to and ideally right up against these pins and their corresponding ground pins. Additionally, low ESR 10 µF capacitors
should be located in the vicinity of the ADC to further reduce
low-frequency ripple.
The DVDD supply of the AD7675 can be either a separate
supply or come from the analog supply, AVDD, or from the
digital interface supply, OVDD. When the system digital supply
is noisy, or fast switching digital signals are present, it is recommended if no separate supply is available, to connect the DVDD
digital supply to the analog supply AVDD through an RC filter
as shown in Figure 5, and connect the system supply to the interface digital supply OVDD and the remaining digital circuitry.
When DVDD is powered from the system supply, it is useful to
insert a bead to further reduce high frequency spikes.
The AD7675 has four different ground pins: REFGND, AGND,
DGND, and OGND. REFGND senses the reference voltage and
should be a low impedance return to the reference because it
carries pulsed currents. AGND is the ground to which most
internal ADC analog signals are referenced. This ground must
be connected with the least resistance to the analog ground
plane. DGND must be tied to the analog or digital ground plane
depending on the configuration. OGND is connected to the
digital system ground.
SER/PAR
RD
It is recommended that running digital lines under the device
should be avoided as these will couple noise onto the die. The
analog ground plane should be allowed to run under the AD7675
to avoid noise coupling. Fast switching signals like CNVST or
clocks should be shielded with digital ground to avoid radiating
noise to other sections of the board, and should never run near
analog signal paths. Crossover of digital and analog signals
should be avoided. Traces on different but close layers of the
board should run at right angles to each other. This will reduce the
effect of feedthrough through the board.
RFS
DR
RCLK
FLAG OR TFS
INVSCLK
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 23. Interfacing to the ADSP-21065L Using
the Serial Master Mode
The layout of the decoupling of the reference voltage is important.
The decoupling capacitor should be close to the ADC and connected
with short and large traces to minimize parasitic inductances.
APPLICATION HINTS
Layout
Evaluating the AD7675 Performance
The AD7675 has very good immunity to noise on the power
supplies as can be seen in Figure 21. However, care should still
be taken with regard to grounding layout.
The printed circuit board that houses the AD7675 should be
designed so the analog and digital sections are separated and
confined to certain areas of the board. This facilitates the use of
ground planes that can be easily separated. Digital and analog
A recommended layout for the AD7675 is outlined in the evaluation board for the AD7675. The evaluation board package
includes a fully assembled and tested evaluation board, documentation, and software for controlling the board from a PC
via the Eval-Control BRD2.
–18–
REV. A
AD7675
OUTLINE DIMENSIONS
48-Lead Plastic Quad Flatpack [LQFP]
1.4 mm Thick
(ST-48)
Dimensions shown in millimeters
1.60 MAX
0.75
0.60
0.45
PIN 1
INDICATOR
9.00 BSC SQ
37
48
36
1
1.45
1.40
1.35
SEATING
PLANE
0.20
0.09
VIEW A
7
3.5
0
0.08 MAX
COPLANARITY
0.15
0.05
7.00
BSC
SQ
TOP VIEW
(PINS DOWN)
25
12
24
13
0.27
0.22
0.17
0.50
BSC
VIEW A
ROTATED 90 CCW
COMPLIANT TO JEDEC STANDARDS MS-026BBC
48-Lead Frame Chip Scale Package [LFCSP]
7 mm 7 mm Body
(CP-48)
Dimensions shown in millimeters
7.00
BSC SQ
0.60 MAX
0.60 MAX
37
6.75
BSC SQ
TOP
VIEW
0.25
REF
48
0.70 MAX
0.65 NOM
1
12
25
24
13
5.50
REF
COPLANARITY
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
REV. A
5.25
4.70
2.25
BOTTOM
VIEW
0.50
0.40
0.30
12 MAX
PIN 1
INDICATOR
36
PIN 1
INDICATOR
1.00
0.90
0.80
0.30
0.23
0.18
–19–
PADDLE
CONNECTED
TO AGND
Revision History
Location
Page
7/02—Data Sheet changed from REV. 0 to REV. A.
Added PulSAR Selection table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Edits to NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Changes to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Additions to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Edits to PIN FUNCTION DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
C02689–0–7/02(A)
Added 48-Lead LFCSP to FEATURES and GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Changes to Power Supply section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
PRINTED IN U.S.A.
Added 48-Lead Frame Chip Scale Package (LFCSP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
–20–
REV. A