Taychipst FR602G Glass passivated fast recovery rectifier Datasheet

FR601G-FR607G
50V-1000V
6.0A
GLASS PASSIVATED FAST RECOVERY RECTIFIERS
FEATURES
•
•
•
•
•
Fast switching for high efficiency
Glass passivated chip junction
High current surge capability
Low leakage
High temperature soldering guaranteed
260 /10 seconds,0.375 (9.5mm)lead length at 5 lbs (2.3kg) tension
MECHANICAL DATA
•
•
•
•
•
•
Case: Transfer molded plastic
Epoxy: UL94V-0 rate flame retardant
Polarity: Color band denotes cathode end
Lead: Plated axial lead, solderable per MIL-STD-202E method 208C
Mounting position: Any
Weight: 0.07 ounce, 2.0 gram
Maximum Ratings and Electrical Characteristics
Rating at 25 oC ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number
Maximum Recurrent Peak Reverse Voltage
Maximum RMS Voltage
Maximum DC Blocking Voltage
Maximum Average Forward Rectified
Current .375”(9.5mm) Lead Length
@T A = 55 oC
Peak Forward Surge Current, 8.3 ms Single
Half Sine-wave Superimposed on Rated
Load (JEDEC method )
Maximum Instantaneous Forward Voltage
@ 6.0A
Maximum DC Reverse Current
@T A =25 oC at Rated DC Blocking Voltage
@ T A =125 oC
Maximum Reverse Recovery Time ( Note 1)
Typical Junction Capacitance ( Note 2 )
Typical Thermal Resistance
Operating Temperature Range
Symbol
V RRM
V RMS
V DC
FR
FR
FR
FR
FR
FR
FR Units
601G 602G 603G 604G 605G 606G 607G
50
100
200
400
600
800 1000
V
35
70
140
280
420
560
700
V
50
100
200
400
600
800 1000
V
I(AV)
6.0
A
IFSM
250
A
VF
1.3
V
IR
5.0
200
uA
uA
nS
pF
o
C/W
o
C
o
C
Trr
Cj
150
R θJA
TJ
250
50
30
-65 to +150
-65 to +150
Storage Temperature Range
T STG
1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A
Notes:
2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 Volts D.C.
3. Mount on Cu-Pad Size 16mm x 16mm on P.C.B.
E-mail: [email protected]
1 of 2
500
Web Site: www.taychipst.com
FR601G-FR607G
50V-1000V
6.0A
GLASS PASSIVATED FAST RECOVREY RECTIFIERS
FIG.1-TYPICAL FORWARD CURRENT
FIG.2-MAXIMUM NON-REPETITIVE PEAK
DERATING CURVE
FORWARD SURGE CURRENT
PEAK FORWARD SURGE
6.0
Half Wave 60Hz
Resistive or
Inductive Load
0.375″(9.5mm)
Lead Length
4.0
2.0
300
CURRENT, (A)
Single Phase
(A)
AVERAGE FORWARD CURRENT,
RATING AND CHRACTERISTIC CURVES FR601G THRU FR607G
8.3ms Single Half Sine-Wave
(JEDEC Method) T= T jmax
200
100
1 Cycle
0
0
25
50 55
150
125
100
75
175
0
1
2
AMBIENT TEMPERATURE, ( C)
4
FIG.3-TYPICAL INSTANTANEOUS
0.1
TJ =25 C
Pulse Width=300us
1% Duty Cycle
0.8
1.0
1.2
1.6
1.4
10
40
20
60 80 100
1.8
20
TJ =125 C
10
TJ =100 C
(μA)
INSTANTANEOUS REVERSE CURRENT,
1.0
(A)
INSTANTANEOUS FORWARD CURRENT,
10
0.6
8
FIG.4-TYPICAL REVERSE
CHARACTERISTICS
FORWARD CHARACTERISTICS
0.01
0.4
6
NUMBER OF CYCLES AT 60 Hz
1.0
TJ =75 C
0.1
TJ=25 C
INSTANTANEOUS FORWARD VOLTAGE,(V)
0.01
0
20
60
40
80
100
120
140
PERCENT OF RATED PEAK
REVERSE VOLTAGE,(%)
FIG.5-TYPICAL JUNCTION CAPACITANCE
F1G.6-TEST CIRCUIT DIAGRAM AND
REVERSE RECOVERY TIME CHARACTERISTIC
JUNCTION CAPACITANCE,(pF)
210
180
Trr
50Ω
10Ω
NONINDUCTIVE NONINDUCTIVE
+0.5A
150
(-)
120
(+)
90
25 Vdc
(approx.)
(-)
D.U.T.
1Ω
NON
INDUCTIVE
PULSE
GENERATIOR
(NOTE 2)
0
-0.25A
(+)
OSCILLOSCOPE
(NOTE 1)
-1.0A
60
1cm
T J =25 C
f=1MHz
Vsig=50mVp-p
30
0
0.1
1.0
10
100
200
NOTES : 1.Rise Time=7ns mas. Input Impedance=
1 magohm. 22pF
2.Rise time=10ns max. Source Impedance=
50 ohms
SET TIME BASE FOR
50/100ns/cm
REVERSE VOLTAGE,(V)
E-mail: [email protected]
2 of 2
Web Site: www.taychipst.com
Similar pages