TI1 LM208A Lm108a lm208a lm308a operational amplifier Datasheet

LM108A,LM208A,LM308A
LM108A LM208A LM308A Operational Amplifiers
Literature Number: SNOSBS6A
LM108A/LM208A/LM308A Operational Amplifiers
General Description
introducing less error than devices like the 709 with 10 kX
sources. Integrators with drifts less than 500 mV/sec and
analog time delays in excess of one hour can be made using capacitors no larger than 1 mF.
The LM208A is identical to the LM108A, except that the
LM208A has its performance guaranteed over a b25§ C to
a 85§ C temperature range, instead of b 55§ C to a 125§ C.
The LM308A devices have slightly-relaxed specifications
and performances over a 0§ C to a 70§ C temperature range.
Features
Y
Y
Y
Y
Offset voltage guaranteed less than 0.5 mV
Maximum input bias current of 3.0 nA over temperature
Offset current less than 400 pA over temperature
Supply current of only 300 mA, even in saturation
Guaranteed 5 mV/§ C drift
e
Y
et
The LM108/LM108A series are precision operational amplifiers having specifications about a factor of ten better than
FET amplifiers over their operating temperature range. In
addition to low input currents, these devices have extremely
low offset voltage, making it possible to eliminate offset adjustments, in most cases, and obtain performance approaching chopper stabilized amplifiers.
The devices operate with supply voltages from g 2V to
g 18V and have sufficient supply rejection to use unregulated supplies. Although the circuit is interchangeable with and
uses the same compensation as the LM101A, an alternate
compensation scheme can be used to make it particularly
insensitive to power supply noise and to make supply bypass capacitors unnecessary.
The low current error of the LM108A series makes possible
many designs that are not practical with conventional amplifiers. In fact, it operates from 10 MX source resistances,
Compensation Circuits
Alternate* Frequency Compensation
bs
ol
Standard Compensation Circuit
Cf t
R1 CO
R1 a R2
CO e 30 pF
*Improves rejection of power supply
noise by a factor of ten.
TL/H/7759 – 1
**Bandwidth and slew rate are proportional to 1/Cf .
TL/H/7759 – 2
**Bandwidth and slew rate are proportional to 1/Cs .
O
Feedforward Compensation
TL/H/7759 – 3
C1995 National Semiconductor Corporation
TL/H/7759
RRD-B30M115/Printed in U. S. A.
LM108A/LM208A/LM308A Operational Amplifiers
May 1989
LM108A/LM208A Absolute Maximum Ratings
b 65§ C to a 150§ C
Storage Temperature Range
Lead Temperature (Soldering, 10 sec.) (DIP)
260§ C
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
(Note 5)
g 20V
Supply Voltage
Soldering Information
Dual-In-Line Package
Soldering (10 sec.)
Small Outline Package
Vapor Phase (60 sec.)
Infrared (15 sec.)
Power Dissipation (Note 1)
500 mW
g 10 mA
Differential Input Current (Note 2)
g 15V
Input Voltage (Note 3)
Output Short-Circuit Duration
Continuous
Operating Free Air Temperature Range
b 55§ C to a 125§ C
LM108A
b 25§ C to a 85§ C
LM208A
260§ C
215§ C
220§ C
See An-450 ‘‘Surface Mounting Methods and Their Effect
on Product Reliability’’ for other methods of soldering surface mount devices.
ESD Tolerance (Note 6)
2000V
Electrical Characteristics (Note 4)
Max
Units
TA e 25§ C
Conditions
Min
0.3
0.5
mV
Input Offset Current
TA e 25§ C
0.05
0.2
nA
Input Bias Current
TA e 25§ C
0.8
2.0
Input Resistance
TA e 25§ C
Supply Current
TA e 25§ C
Large Signal Voltage Gain
TA e 25§ C, VS e g 15V,
VOUT e g 10V, RL t 10 kX
30
70
0.3
Input Offset Voltage
Average Temperature Coefficient
of Input Offset Voltage
80
0.6
300
1.0
bs
ol
Input Offset Current
Average Temperature Coefficient
of Input Offset Current
0.5
Input Bias Current
Supply Current
nA
MX
mA
et
Parameter
e
Typ
Input Offset Voltage
TA e 125§ C
0.15
Large Signal Voltage Gain
VS e g 15V, VOUT e g 10V,
RL t 10 kX
Output Voltage Swing
VS e g 15V, RL e 10 kX
Input Voltage Range
VS e g 15V
40
g 13
g 14
g 13.5
V/mV
1.0
mV
5.0
mV/§ C
0.4
nA
2.5
pA/§ C
3.0
nA
0.4
mA
V/mV
V
V
Common Mode Rejection Ratio
96
110
dB
Supply Voltage Rejection Ratio
96
110
dB
O
Note 1: The maximum junction temperature of the LM108A is 150§ C, while that of the LM208A is 100§ C. For operating at elevated temperatures, devices in the H08
package must be derated based on a thermal resistance of 160§ C/W, junction to ambient, or 20§ C/W, junction to case. The thermal resistance of the dual-in-line
package is 100§ C/W, junction to ambient.
Note 2: The inputs are shunted with back-to-back diodes for overvoltage protection. Therefore, excessive current will flow if a differential input voltage in excess of
1V is applied between the inputs unless some limiting resistance is used.
Note 3: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 4: These specifications apply for g 5V s VS s g 20V and b 55§ C s TA s 125§ C, unless otherwise specified. With the LM208A, however, all temperature
specifications are limited to b 25§ C s TA s 85§ C.
Note 5: Refer to RETS108AX for LM108AH and LM108AJ-8 military specifications.
Note 6: Human body model, 1.5 kX in series with 100 pF.
2
LM308A Absolute Maximum Ratings
Lead Temperature (Soldering, 10 sec.) (DIP)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales
Office/Distributors for availability and specifications.
Supply Voltage
Power Dissipation (Note 1)
Differential Input Current (Note 2)
Input Voltage (Note 3)
Output Short-Circuit Duration
Operating Temperature Range
Storage Temperature Range
H-Package Lead Temperature
(Soldering, 10 sec.)
Soldering Information
Dual-In-Line Package
Soldering (10 sec.)
Small Outline Package
Vapor phase (60 sec.)
Infrared (15 sec.)
g 18V
500 mW
g 10 mA
g 15V
Continuous
0§ C to a 70§ C
b 65§ C to a 150§ C
260§ C
260§ C
215§ C
220§ C
See An-450 ‘‘Surface Mounting Methods and Their Effect
on Product Reliability’’ for other methods of soldering surface mount devices.
ESD rating to be determined.
300§ C
Electrical Characteristics (Note 4)
Conditions
TA e 25§ C
Input Offset Current
TA e 25§ C
Input Bias Current
TA e 25§ C
Input Resistance
TA e 25§ C
Supply Current
TA e 25§ C, VS e g 15V
Large Signal Voltage Gain
TA e 25§ C, VS e g 15V,
VOUT e g 10V, RL t 10 kX
Input Offset Voltage
VS e g 15V, RS e 100X
Average Temperature Coefficient
of Input Offset Voltage
VS e g 15V, RS e 100X
Min
Typ
Max
Units
0.3
0.5
mV
e
Parameter
Input Offset Voltage
10
0.2
1
1.5
7
40
80
0.8
300
bs
ol
2.0
Input Offset Current
Average Temperature Coefficient
of Input Offset Current
2.0
Input Bias Current
Large Signal Voltage Gain
VS e g 15V, VOUT e g 10V,
RL t 10 kX
Output Voltage Swing
VS e g 15V, RL e 10 kX
g 13
Input Voltage Range
VS e g 15V
g 14
60
g 14
nA
MX
et
0.3
nA
mA
V/mV
0.73
mV
5.0
mV/§ C
1.5
nA
10
pA/§ C
10
nA
V/mV
V
V
Common Mode Rejection Ratio
96
110
dB
Supply Voltage Rejection Ratio
96
110
dB
O
Note 1: The maximum junction temperature of the LM308A is 85§ C. For operating at elevated temperatures, devices in the H08 package must be derated based on
a thermal resistance of 160§ C/W, junction to ambient, or 20§ C/W, junction to case. The thermal resistance of the dual-in-line package is 100§ C/W, junction to
ambient.
Note 2: The inputs are shunted with back-to-back diodes for overvoltage protection. Therefore, excessive current will flow if a differential input voltage in excess of
1V is applied between the inputs unless some limiting resistance is used.
Note 3: For supply voltages less than g 15V, the absolute maximum input voltage is equal to the supply voltage.
Note 4: These specifications apply for g 5V s VS s g 15V and 0§ C s TA s a 70§ C, unless otherwise specified.
3
Typical Applications
Sample and Hold
² Teflon, polyethylene or polycarbonate dielectric capacitor.
Worst case drift less than 2.5 mV/sec.
e
TL/H/7759 – 4
O
bs
ol
et
High Speed Amplifier with Low Drift and Low Input Current
TL/H/7759 – 5
4
Application Hints
Resistors can cause other errors besides gradient generated voltages. If the gain setting resistors do not track with
temperature a gain error will result. For example, a gain of
1000 amplifier with a constant 10 mV input will have a 10V
output. If the resistors mistrack by 0.5% over the operating
temperature range, the error at the output is 50 mV. Referred to input, this is a 50 mV error. All of the gain fixing
resistor should be the same material.
Testing low drift amplifiers is also difficult. Standard drift
testing technique such as heating the device in an oven and
having the leads available through a connector, thermoprobe, or the soldering iron methodÐdo not work. Thermal
gradients cause much greater errors than the amplifier drift.
Coupling microvolt signal through connectors is especially
bad since the temperature difference across the connector
can be 50§ C or more. The device under test along with the
gain setting resistor should be isothermal.
e
A very low drift amplifier poses some uncommon application
and testing problems. Many sources of error can cause the
apparent circuit drift to be much higher than would be predicted.
Thermocouple effects caused by temperature gradient
across dissimilar metals are perhaps the worst offenders.
Only a few degrees gradient can cause hundreds of microvolts of error. The two places this shows up, generally, are
the package-to-printed circuit board interface and temperature gradients across resistors. Keeping package leads
short and the two input leads close together helps greatly.
Resistor choice as well as physical placement is important
for minimizing thermocouple effects. Carbon, oxide film and
some metal film resistors can cause large thermocouple errors. Wirewound resistors of evanohm or manganin are best
since they only generate about 2 mV/§ C referenced to copper. Of course, keeping the resistor ends at the same temperature is important. Generally, shielding a low drift stage
electrically and thermally will yield good results.
O
bs
ol
et
Schematic Diagram
TL/H/7759 – 6
5
Connection Diagrams
Dual-In-Line Package
Metal Can Package
TL/H/7759–7
Pin 4 is connected to the case.
TL/H/7759 – 8
Top View
**Unused pin (no internal connection) to allow for input anti-leakage guard
ring on printed circuit board layout.
Order Number LM108AJ-8, LM208AJ-8, LM308AJ-8,
LM308AM or LM308AN
See NS Package Number J08A, M08A or N08E
Order Number LM108AH, LM208AH or LM208AH
See NS Package Number H08C
O
bs
ol
et
e
Physical Dimensions inches (millimeters)
Metal Can Package (H)
Order Number LM108AH, LM208AH or LM308AH
NS Package Number H08C
6
et
e
Physical Dimensions inches (millimeters) (Continued)
O
bs
ol
Ceramic Dual-In-Line Package (J)
Order Number LM108AJ-8, LM208AJ-8 or LM308AJ-8
NS Package Number J08A
S.O. Package (M)
Order Number LM308AM
NS Package Number M08A
7
e
et
Molded Dual-In-Line Package (N)
Order Number LM308AN
NS Package Number N08E
bs
ol
LM108A/LM208A/LM308A Operational Amplifiers
Physical Dimensions inches (millimeters) (Continued)
LIFE SUPPORT POLICY
O
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF NATIONAL
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and whose
failure to perform, when properly used in accordance
with instructions for use provided in the labeling, can
be reasonably expected to result in a significant injury
to the user.
National Semiconductor
Corporation
1111 West Bardin Road
Arlington, TX 76017
Tel: 1(800) 272-9959
Fax: 1(800) 737-7018
2. A critical component is any component of a life
support device or system whose failure to perform can
be reasonably expected to cause the failure of the life
support device or system, or to affect its safety or
effectiveness.
National Semiconductor
Europe
Fax: (a49) 0-180-530 85 86
Email: cnjwge @ tevm2.nsc.com
Deutsch Tel: (a49) 0-180-530 85 85
English Tel: (a49) 0-180-532 78 32
Fran3ais Tel: (a49) 0-180-532 93 58
Italiano Tel: (a49) 0-180-534 16 80
National Semiconductor
Hong Kong Ltd.
13th Floor, Straight Block,
Ocean Centre, 5 Canton Rd.
Tsimshatsui, Kowloon
Hong Kong
Tel: (852) 2737-1600
Fax: (852) 2736-9960
National Semiconductor
Japan Ltd.
Tel: 81-043-299-2309
Fax: 81-043-299-2408
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
Communications and Telecom www.ti.com/communications
Amplifiers
amplifier.ti.com
Computers and Peripherals
www.ti.com/computers
Data Converters
dataconverter.ti.com
Consumer Electronics
www.ti.com/consumer-apps
DLP® Products
www.dlp.com
Energy and Lighting
www.ti.com/energy
DSP
dsp.ti.com
Industrial
www.ti.com/industrial
Clocks and Timers
www.ti.com/clocks
Medical
www.ti.com/medical
Interface
interface.ti.com
Security
www.ti.com/security
Logic
logic.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and Automotive www.ti.com/automotive
Microcontrollers
microcontroller.ti.com
Video and Imaging
RFID
www.ti-rfid.com
OMAP Mobile Processors
www.ti.com/omap
Wireless Connectivity
www.ti.com/wirelessconnectivity
TI E2E Community Home Page
www.ti.com/video
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
Similar pages