Common Source Push-Pull Pair ARF476FL D G S S G RF POWER MOSFET S S D N - CHANNEL PUSH - PULL PAIR 165V 450W 150MHz The ARF475FL is a matched pair of RF power transistors in a common source configuration. It is designed for high voltage push-pull or parallel operation in narrow band ISM and MRI power amplifiers up to 150 MHz. • High Performance Push-Pull RF Package. • High Voltage Breakdown and Large SOA • Specified 150 Volt, 128 MHz Characteristics: • Output Power = 900 Watts Peak • Gain = 15dB (Class AB) • Efficiency = 50% min for Superior Ruggedness. • Low Thermal Resistance. • RoHS Compliant * *Pb Free Terminal Finish. All Ratings: TC = 25°C unless otherwise specified. MAXIMUM RATINGS Symbol Parameter ARF476FL VDSS Drain-Source Voltage 500 VDGO Drain-Gate Voltage 500 ID Continuous Drain Current @ TC = 25°C (each device) UNIT Volts 10 Amps VGS Gate-Source Voltage ±30 Volts PD Total Device Dissipation @ TC = 25°C 910 Watts TJ,TSTG TL -55 to 175 Operating and Storage Junction Temperature Range °C 300 Lead Temperature: 0.063" from Case for 10 Sec. STATIC ELECTRICAL CHARACTERISTICS (each device) Symbol BVDSS VDS(ON) IDSS IGSS gfs gfs1 gfs2 / VGS(TH) DVGS(TH) Characteristic / Test Conditions MIN Drain-Source Breakdown Voltage (VGS = 0V, ID = 250 μA) 500 On State Drain Voltage 1 (I D(ON) = 5A, VGS = 10V) TYP MAX 2.9 4 100 Zero Gate Voltage Drain Current (VDS = VDSS, VGS = 0V) 500 Zero Gate Voltage Drain Current (VDS = 50V, VGS = 0, TC = 125°C) ±100 Gate-Source Leakage Current (VGS = ±30V, VDS = 0V) Forward Transconductance (VDS = 15V, ID = 5A) Forward Transconductance Match Ratio (VDS = 15V, ID = 5A) Gate Threshold Voltage (VDS = VGS, ID = 200mA) 3 3.6 0.9 2 UNIT Volts μA nA mhos 1.1 3.3 4 0.2 Gate Threshold Voltage Match (VDS = VGS, ID = 200mA) Volts THERMAL CHARACTERISTICS Characteristic MIN TYP MAX RθJC Junction to Case 0.15 0.165 RθJHS Junction to Sink (Use High Efficiency Thermal Grease and Planar Heat Sink Surface.) 0.30 0.33 CAUTION: These Devices are Sensitive to Electrostatic Discharge. Proper Handling Procedures Should Be Followed. Microsemi Website - http://www.microsemi.com UNIT °C/W 050-4931 C 12-2010 Symbol DYNAMIC CHARACTERISTICS (per section) Symbol TYP MAX 780 830 VDS = 50V f = 1MHz 125 130 7 9 Test Conditions Characteristic MIN Input Capacitance Coss Output Capacitance Crss Reverse Transfer Capacitance td(on) Turn-on Delay Time VGS = 15V 5.1 10 Rise Time VDD = 250V 4.1 8 ID = ID[Cont.] @ 25°C 12 18 RG = 1.6 W 4.0 7 MIN TYP MAX 14 16 dB 50 55 % td(off) tf VGS = 0V Turn-off Delay Time Fall Time FUNCTIONAL CHARACTERISTICS Symbol GPS Characteristic Test Conditions Common Source Amplifier Power Gain η Drain Efficiency ψ Electrical Ruggedness VSWR 5:1 f = 128 MHz Idq = 15mA VDD = 150V Pout = 900W PW = 3ms 10% duty cycle Per transistor section unless otherwise specified. 3000 12V 10V 9V 15 8V 10 Coss 100 50 10 0 5 10 15 20 25 30 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 1, Typical Output Characteristics 20 TJ = +25°C 15 10 0 TJ = -55°C TJ = +125°C 0 2 4 6 8 10 VGS, GATE-TO-SOURCE VOLTAGE (VOLTS) Figure 3, Typical Transfer Characteristics VGS(th), THRESHOLD VOLTAGE (NORMALIZED) ID, DRAIN CURRENT (AMPERES) 1.10 VDS> ID (ON) x RDS (ON)MAX. 250μSEC. PULSE TEST @ <0.5 % DUTY CYCLE TJ = -55°C 5 Crss 1 .1 1 10 100 200 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 2, Typical Capacitance vs. Drain-to-Source Voltage 30 25 Ciss 500 7V 5 0 1000 11V CAPACITANCE (pf) ID, DRAIN CURRENT (AMPERES) 30 20 ns UNIT No Degradation in Output Power Pulse Test: Pulse width < 380 μS, Duty Cycle < 2%. 25 pF (Push-Pull Configuration) Microsemi Reserves the right to change, without notice, the specifications and information contained herein. 050-4931 C 12-2010 UNIT Ciss tr 1 ARF476FL 1.05 1.00 0.95 0.90 -50 -25 0 25 50 75 100 125 150 TC, CASE TEMPERATURE (°C) Figure 4, Typical Threshold Voltage vs Temperature ARF476FL 0.18 0.16 D = 0.9 0.14 0.7 0.12 0.10 0.5 0.08 0.06 PDM Note: 0.3 t2 0.04 SINGLE PULSE t Duty Factor D = 1/t2 Peak TJ = PDM x ZθJC + TC 0.1 0.02 0.05 10-4 10-3 10-2 10-1 1.0 RECTANGULAR PULSE DURATION (SECONDS) FIGURE 5a, MAXIMUM EFFECTIVE TRANSIENT THERMAL IMPEDANCE, JUNCTION-TO-CASE vs PULSE DURATION 10-5 200 OPERATION HERE LIMITED BY R (ON) DS TJ ( C) TC ( C) 0.0755 0.0135F 0.0893 ZEXT Dissipated Power (Watts) 0.161F ZEXT are the external thermal impedances: Case to sink, sink to ambient, etc. Set to zero when modeling only the case to junction. Figure 5b, TRANSIENT THERMAL IMPEDANCE MODEL ID, DRAIN CURRENT (AMPERES) 100 DC Line 10 10µs 100µs 1ms 10ms 1 100ms TC =+25°C TJ =+175°C SINGLE PULSE 0.1 1 10 100 800 VDS, DRAIN-TO-SOURCE VOLTAGE (VOLTS) Figure 6, Typical Maximum Safe Operating Area Table 1 - Typical Series Equivalent Large Signal Input - Output Impedance Freq. (MHz) 30 60 90 120 150 Zin (Ω) gate to gate 5.2 -j10 1.37 -j5.2 .53 -j2.6 .25 -j1.0 .25 +j0.2 ZOL (Ω) drain - drain 41 -j20 26 -j25 16 -j23 10 -j20 6.7 -j17 Zin - Gate -gate shunted with 25Ω IDQ = 15mA each side ZOL - Conjugate of optimum load for 600 Watts peak output at Vdd = 150V 25% duty cycle and PW = 5ms 050-4931 C 12-2010 0 t1 ARF476FL 128MHz Test amplifier Po = 900W @150V 3ms pulse 10% Duty Cycle + Vg1 C6 L2 R3 T2 T1 C3 C8 C11 C10 T3 L1 C2 C1 TL5 TL1 C7 L3 TL3 R1 J1 C5 + Vdd - J2 TL2 C4 R4 R2 C1 25pF poly trimmer C2 750pF ATC 700B C3-4 2200pF NPO 500V chip C5-10 10nF 500V chip C11 1000uF 250V electroytic L1 30nH 1.5t #18 enam .375" dia L2 680nH 12t #24 enam .312" dia L3 2t #20 on Fair-Rite 2643006302 bead, ~ 2uH C9 Vg2 DUT TL4 TL6 R1-2 3.1Ω : 3 parallel 22Ω 1W 2512 SMT R3-4 2.2kΩ 1/4W axial T1 1:1 balun 50Ω coax on Fair-Rite 2843000102 core T2 4:1 25Ω coax on 2843000102 Fair-Rite balun core T3 1:1 coax balun RG-303 on 2861006802 Fair-Rite core TL1-2 Printed line L= 0.75" w=.23" TL3-6 Printed line L= 0.65" w=.23" 0.23" wide stripline on FR-4 board is ~ 30Ω Zo Peak Output Power vs. Vdd and Duty Cycle 1.2 900 800 1 Max Duty Cycle 700 0.8 600 500 0.6 Po Watts 400 300 0.4 200 Notes: The value of L1 must be adjusted as the supply voltage is changed to maintain resonance in the output circuit. At 128MHz its value changes from approximately 40nH at 100V to 30nH at 150V. With the 50Ω drain-to-drain load, the duty cycle above 100V must be reduced to insure power dissipation is within the limits of the device. Maximum pulse length should be 100mS or less. See transient thermal impedance, figure 5. 0.2 100 0 0 80 100 120 140 160 Drain Supply Voltage Vdd .100 .100 .100 Thermal Considerations and Package Mounting: .325 +/- .010 1.000 .125R 4 pls .080 .125dia 4 pls .570 ARF476FL .320 The package design clamps the ceramic base to the heatsink. A clamped joint maintains the required mounting pressure while allowing for thermal expansion of both the base and the heat sink. Four 4-40 (M3) screws provide the required mounting force. T = 6 in-lb (0.68 N-m). 1.250 050-4931 C 12-2010 .175 .150 .150 .325 .175 .200 .300 .005 .040 1.500 The rated power dissipation is only available when the package mounting surface is at 25°C and the junction temperature is 175°C. The thermal resistance between junctions and case mounting surface is 0.16 °C/W. When installed, an additional thermal impedance of 0.15°C/W between the package base and the mounting surface is typical. Insure that the mounting surface is smooth and flat. Thermal joint compound must be used to reduce the effects of small surface irregularities. Use the minimum amount necessary to coat the surface. The heatsink should incorporate a copper heat spreader to obtain best results. HAZARDOUS MATERIAL WARNING The white ceramic portion of the device between leads and mounting surface is beryllium oxide, BeO. Beryllium oxide dust is toxic when inhaled. Care must be taken during handling and mounting to avoid damage to this area. These devices must never be thrown away with general industrial or domestic waste.