1.0X0.5mm SMD CHIP LED LAMP Part Number: APHHS1005QBC/D Blue ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 1.0mmX0.5mm SMD LED, 0.5mm thickness. z The Blue source color devices are made with InGaN z Low power consumption. Light Emitting Diode. z Wide viewing angle. z Electrostatic discharge and power surge could damage z Ideal for backlight and indicator. the LEDs. z It is recommended to use a wrist band or anti- z Package: 2000pcs / reel . z Moisture sensitivity level : level 3. z RoHS compliant. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAJ8746 REV NO: V.7B DATE: JUL/01/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008565 Selection Guide Part No. Emitting Color (Material) APHHS1005QBC/D Blue (InGaN) Iv (mcd) [2] @ 20mA Lens Type Viewing Angle [1] Min. Typ. 2θ1/2 40 60 140° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Blue λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 460 nm IF=20mA Blue 465 nm IF=20mA Spectral Line Half-width Blue 25 nm IF=20mA C Capacitance Blue 100 pF VF=0V;f=1MHz VF [2] Forward Voltage Blue 3.3 4 V IF=20mA IR Reverse Current Blue 50 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 120 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA Electrostatic Discharge Threshold (HBM) 250 V 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAJ8746 REV NO: V.7B DATE: JUL/01/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008565 Blue APHHS1005QBC/D SPEC NO: DSAJ8746 REV NO: V.7B DATE: JUL/01/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008565 APHHS1005QBC/D Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAJ8746 REV NO: V.7B DATE: JUL/01/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008565 PACKING & LABEL SPECIFICATIONS APHHS1005QBC/D Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAJ8746 REV NO: V.7B DATE: JUL/01/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1203008565