Notice for TAIYO YUDEN products Please read this notice before using the TAIYO YUDEN products. REMINDERS ■ Product information in this catalog is as of October 2013. All of the contents specified herein are subject to change without notice due to technical improvements, etc. Therefore, please check for the latest information carefully before practical application or usage of the Products. Please note that TAIYO YUDEN CO., LTD. shall not be responsible for any defects in products or equipment incorporating such products, which are caused under the conditions other than those specified in this catalog or individual specification. ■ Please contact TAIYO YUDEN CO., LTD. for further details of product specifications as the individual specification is available. ■ Please conduct validation and verification of products in actual condition of mounting and operating environment before commercial shipment of the equipment. ■ All electronic components or functional modules listed in this catalog are developed, designed and intended for use in general electronics equipment.(for AV, office automation, household, office supply, information service, telecommunications, (such as mobile phone or PC) etc.). Before incorporating the components or devices into any equipment in the field such as transportation,( automotive control, train control, ship control), transportation signal, disaster prevention, medical, public information network (telephone exchange, base station) etc. which may have direct influence to harm or injure a human body, please contact TAIYO YUDEN CO., LTD. for more detail in advance. Do not incorporate the products into any equipment in fields such as aerospace, aviation, nuclear control, submarine system, military, etc. where higher safety and reliability are especially required. In addition, even electronic components or functional modules that are used for the general electronic equipment, if the equipment or the electric circuit require high safety or reliability function or performances, a sufficient reliability evaluation check for safety shall be performed before commercial shipment and moreover, due consideration to install a protective circuit is strongly recommended at customer's design stage. ■ The contents of this catalog are applicable to the products which are purchased from our sales offices or distributors (so called TAIYO YUDEN s official sales channel ). It is only applicable to the products purchased from any of TAIYO YUDEN s official sales channel. ■ Please note that TAIYO YUDEN CO., LTD. shall have no responsibility for any controversies or disputes that may occur in connection with a third party's intellectual property rights and other related rights arising from your usage of products in this catalog. TAIYO YUDEN CO., LTD. grants no license for such rights. ■ Caution for export Certain items in this catalog may require specific procedures for export according to Foreign Exchange and Foreign Trade Control Law of Japan, U.S. Export Administration Regulations , and other applicable regulations. Should you have any question or inquiry on this matter, please contact our sales staff. 14 RADIAL LEADED INDUCTORS RADIAL LEADED INDUCTORS WAVE ■PARTS NUMBER L H △ ① *Operating Temp. : -25～+105℃（Including self-generated heat） L △ ② ①Series name Code LH△ 0 8 ③ T B 1 0 1 ⑤ ④ K △ △ △ ⑥ ⑦ ④Packaging Code NB TB Series name Radial leaded inductor ／ LEADED INDUCTORS INDUCTORS ②Characteristics Code L△ LP LC Characteristics Standard type Taping available Shielded type Bulk High current type ③Dimensions（D） Code 08 10 12 13 16 Dimensions（D）［mm max.］ 9.0 11.0 13.0 14.0 17.0 △＝Blank space Packaging Bulk（LHL） Ammo packaging（LHL） ⑤Nominal inductance Code （example） 1R0 150 102 ※R＝Decimal point ⑥Inductance tolerance Code J K M N ⑦Internal code Code △△△ Nominal inductance［μH］ 1.0 15 1000 Inductance tolerance ±5％ ±10％ ±20％ ±30％ Internal code Standard ■STANDARD EXTERNAL DIMENSIONS / STANDARD QUANTITY LHL /LHLC LH LH LH LH LHLP Type D H2 ℓ F φd L 08 LC08 L 10 LC10 9.0 max （0.354 max） 11.0 max （0.433 max） 14.0 max （0.551 max） 17.0 max （0.669 max） 11.0 max （0.433 max） 13.0 max （0.512 max） 17.0 max （0.669 max） 9.5 max （0.374 max） 14.0 max （0.551 max） 17.0 max （0.669 max） 21.0 max （0.827 max） 11.0 max （0.433 max） 16.0 max （0.624 max） 19.0 max （0.741 max） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 7.5±1.0 （0.295±0.039） 7.5±1.0 （0.295±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 7.5±1.0 （0.295±0.039） 0.6±0.05 （0.024±0.002） 0.6±0.05 （0.024±0.002） 0.8±0.05 （0.031±0.002） 0.8±0.05 （0.031±0.002） 0.6±0.05 （0.024±0.002） 0.6±0.05 （0.024±0.002） 0.8±0.05 （0.031±0.002） LH L 13 LH L 16 LH LP10 LH LP12 LH LP16 Box Standard quantity [pcs] Bulk Taping － 100 1000 － 50 500 － 25 500 500 － 250 500 － 200 300 － － － － 200 Unit：mm（inch） i_leaded_LH_e-E02R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 84 14 ■PARTS NUMBER ●LHL08 Parts number EHS Nominal inductance ［μH］ Q （min.） Self-resonant frequency ［MHｚ］（min..） DC Resistance ［Ω］（max.） Rated current ［A］（max.） Measuring frequency ［MHz］ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ 40 40 40 40 40 40 40 40 40 40 65 65 50 50 50 50 40 40 40 40 35 35 25 25 20 35 35 25 25 20 25 25 25 30 55 45 55 55 55 55 55 55 65 65 65 65 60 60 60 60 60 60 60 76 65 56 48 41 33 30 23 21 19 17 16 13 12 11 10 8.8 8.4 8.2 7.9 7.0 6.5 5.7 5.2 4.7 4.2 3.7 3.5 3.2 2.9 2.4 2.2 2.0 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.85 0.78 0.68 0.62 0.61 0.60 0.48 0.44 0.35 0.30 0.28 0.25 0.23 0.013 0.014 0.017 0.019 0.021 0.024 0.025 0.028 0.030 0.034 0.041 0.044 0.053 0.060 0.068 0.091 0.10 0.12 0.15 0.17 0.20 0.22 0.32 0.36 0.41 0.66 0.73 0.85 0.97 1.1 1.3 1.5 1.8 2.3 2.7 3.2 4.1 4.8 5.6 7.5 8.5 9.7 14 16 18 20 32 36 62 72 82 90 100 4.7 4.4 4.1 3.5 3.2 3.1 3.0 2.9 2.8 2.5 2.4 2.3 2.0 1.9 1.8 1.5 1.4 1.3 1.2 1.1 1.0 0.90 0.79 0.70 0.64 0.60 0.53 0.51 0.44 0.41 0.38 0.35 0.32 0.30 0.25 0.22 0.20 0.19 0.16 0.15 0.14 0.11 0.10 0.093 0.092 0.084 0.070 0.064 0.051 0.048 0.044 0.042 0.040 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz ／ LEADED INDUCTORS INDUCTORS LH L 08[]1R0N RoHS 1.0 LH L 08[]1R5M RoHS 1.5 LH L 08[]2R2M RoHS 2.2 LH L 08[]2R7M RoHS 2.7 LH L 08[]3R3M RoHS 3.3 LH L 08[]3R9M RoHS 3.9 LH L 08[]4R7M RoHS 4.7 LH L 08[]5R6M RoHS 5.6 LH L 08[]6R8M RoHS 6.8 LH L 08[]8R2M RoHS 8.2 LH L 08[]100K RoHS 10 LH L 08[]120K RoHS 12 LH L 08[]150K RoHS 15 LH L 08[]180K RoHS 18 LH L 08[]220K RoHS 22 LH L 08[]270K RoHS 27 LH L 08[]330K RoHS 33 LH L 08[]390K RoHS 39 LH L 08[]470K RoHS 47 LH L 08[]560K RoHS 56 LH L 08[]680K RoHS 68 LH L 08[]820K RoHS 82 LH L 08[]101K RoHS 100 LH L 08[]121K RoHS 120 LH L 08[]151K RoHS 150 LH L 08[]181K RoHS 180 LH L 08[]221K RoHS 220 LH L 08[]271K RoHS 270 LH L 08[]331K RoHS 330 LH L 08[]391K RoHS 390 LH L 08[]471K RoHS 470 LH L 08[]561K RoHS 560 LH L 08[]681K RoHS 680 LH L 08[]821K RoHS 820 LH L 08[]102J RoHS 1000 LH L 08[]122J RoHS 1200 LH L 08[]152J RoHS 1500 LH L 08[]182J RoHS 1800 LH L 08[]222J RoHS 2200 LH L 08[]272J RoHS 2700 LH L 08[]332J RoHS 3300 LH L 08[]392J RoHS 3900 LH L 08[]472J RoHS 4700 LH L 08[]562J RoHS 5600 LH L 08[]682J RoHS 6800 LH L 08[]822J RoHS 8200 LH L 08[]103J RoHS 10000 LH L 08[]123J RoHS 12000 LH L 08[]153J RoHS 15000 LH L 08[]183J RoHS 18000 LH L 08[]223J RoHS 22000 LH L 08[]273J RoHS 27000 LH L 08[]333J RoHS 33000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) Inductance tolerance i_leaded_LH_e-E02R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 85 ■PARTS NUMBER ●LHL10 Parts number ／ LEADED INDUCTORS INDUCTORS LH L 10[]3R3M LH L 10[]3R9M LH L 10[]4R7M LH L 10[]5R6M LH L 10[]6R8M LH L 10[]8R2M LH L 10[]100K LH L 10[]120K LH L 10[]150K LH L 10[]180K LH L 10[]220K LH L 10[]270K LH L 10[]330K LH L 10[]390K LH L 10[]470K LH L 10[]560K LH L 10[]680K LH L 10[]820K LH L 10[]101K LH L 10[]121K LH L 10[]151K LH L 10[]181K LH L 10[]221K LH L 10[]271K LH L 10[]331K LH L 10[]391K LH L 10[]471K LH L 10[]561K LH L 10[]681K LH L 10[]821K LH L 10[]102J LH L 10[]122J LH L 10[]152J LH L 10[]182J LH L 10[]222J LH L 10[]272J LH L 10[]332J LH L 10[]392J LH L 10[]472J LH L 10[]562J LH L 10[]682J LH L 10[]822J LH L 10[]103J LH L 10[]123J LH L 10[]153J LH L 10[]183J LH L 10[]223J LH L 10[]273J LH L 10[]333J LH L 10[]393J LH L 10[]473J LH L 10[]563J LH L 10[]683J LH L 10[]823J LH L 10[]104J LH L 10[]124J LH L 10[]154J EHS Nominal inductance ［μH］ Inductance tolerance Q （min.） Self-resonant frequency ［MHｚ］（min..） DC Resistance ［Ω］（max.） Rated current ［A］（max.） Measuring frequency ［MHz］ RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 3.3 3.9 4.7 5.6 6.8 8.2 10 12 15 18 22 27 33 39 47 56 68 82 100 120 150 180 220 270 330 390 470 560 680 820 1000 1200 1500 1800 2200 2700 3300 3900 4700 5600 6800 8200 10000 12000 15000 18000 22000 27000 33000 39000 47000 56000 68000 82000 100000 120000 150000 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ 50 50 50 50 50 50 90 90 90 90 60 60 60 60 50 50 40 40 40 40 40 40 40 30 30 30 30 30 30 30 50 50 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 40 40 40 40 30 30 30 30 30 30 46 40 38 34 30 24 19 16 12 9.2 8.6 7.1 6.8 6.7 6.2 5.2 4.9 4.7 3.8 3.2 2.9 2.6 2.3 2.1 2.0 1.8 1.7 1.5 1.4 1.3 1.2 0.87 0.83 0.75 0.70 0.67 0.56 0.54 0.49 0.41 0.38 0.36 0.29 0.27 0.24 0.21 0.20 0.15 0.14 0.13 0.12 0.10 0.095 0.088 0.085 0.070 0.069 0.019 0.022 0.024 0.025 0.028 0.031 0.034 0.038 0.042 0.046 0.061 0.069 0.078 0.085 0.093 0.10 0.12 0.13 0.18 0.25 0.29 0.40 0.44 0.50 0.56 0.62 0.84 0.93 1.0 1.4 1.8 2.3 2.7 3.0 3.9 4.3 5.8 6.4 7.1 9.0 10 12 19 21 34 38 43 67 76 84 96 170 200 210 240 260 300 4.2 4.1 4.0 3.8 3.4 3.3 3.2 2.8 2.6 2.4 2.1 2.0 1.9 1.8 1.7 1.6 1.5 1.4 1.2 1.0 0.95 0.80 0.75 0.70 0.68 0.63 0.57 0.52 0.48 0.42 0.41 0.33 0.30 0.29 0.25 0.24 0.21 0.20 0.19 0.17 0.16 0.15 0.12 0.11 0.090 0.081 0.075 0.060 0.056 0.053 0.050 0.036 0.035 0.033 0.031 0.030 0.028 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0252MHz L：1kHz， Q：0.0252MHz L：1kHz， Q：0.0252MHz EHS Nominal inductance ［μH］ Inductance tolerance Q （min.） Self-resonant frequency ［MHｚ］（min..） DC Resistance ［Ω］（max.） Rated current ［A］（max.） Measuring frequency ［MHz］ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ 140 140 100 100 70 50 50 50 40 30 30 30 30 40 40 40 40 30 70 19 12 7.6 6.9 5.6 4.4 3.3 2.6 2.2 1.8 1.5 1.2 1.0 0.83 0.70 0.60 0.43 0.38 0.30 0.023 0.028 0.035 0.043 0.052 0.070 0.12 0.19 0.23 0.35 0.43 0.61 1.2 1.8 2.2 3.4 4.7 5.6 10 4.5 4.0 3.4 3.2 2.8 2.4 2.0 1.5 1.3 1.1 0.90 0.80 0.60 0.45 0.40 0.33 0.28 0.25 0.19 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 L：1kHz， Q：0.0796MHz ●LHL13 Parts number LH L 13[]100K RoHS 10 LH L 13[]150K RoHS 15 LH L 13[]220K RoHS 22 LH L 13[]330K RoHS 33 LH L 13[]470K RoHS 47 LH L 13[]680K RoHS 68 LH L 13[]101K RoHS 100 LH L 13[]151K RoHS 150 LH L 13[]221K RoHS 220 LH L 13[]331K RoHS 330 LH L 13[]471K RoHS 470 LH L 13[]681K RoHS 680 LH L 13[]102J RoHS 1000 LH L 13[]152J RoHS 1500 LH L 13[]222J RoHS 2200 LH L 13[]332J RoHS 3300 LH L 13[]472J RoHS 4700 LH L 13[]682J RoHS 6800 LH L 13[]103J RoHS 10000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) i_leaded_LH_e-E02R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 86 14 ■PARTS NUMBER ●LHL16 Parts number LH L 16[]470K LH L 16[]680K LH L 16[]101K LH L 16[]151K LH L 16[]221K LH L 16[]331K LH L 16[]471K LH L 16[]681K LH L 16[]102J LH L 16[]152J LH L 16[]222J LH L 16[]332J LH L 16[]472J LH L 16[]682J LH L 16[]103J Nominal inductance ［μH］ Inductance tolerance Q （min.） Self-resonant frequency ［MHｚ］（min..） DC Resistance ［Ω］（max.） Rated current ［A］（max.） Measuring frequency ［MHz］ RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 47 68 100 150 220 330 470 680 1000 1500 2200 3300 4700 6800 10000 ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ 70 70 60 60 60 40 30 20 20 20 20 20 20 20 70 4.5 3.9 2.7 2.3 1.9 1.6 1.4 1.2 0.84 0.69 0.56 0.49 0.41 0.35 0.26 0.046 0.054 0.077 0.11 0.15 0.21 0.28 0.35 0.74 0.93 1.4 2.2 2.6 3.9 7.3 3.7 3.3 2.9 2.4 2.0 1.5 1.3 1.1 0.86 0.75 0.60 0.50 0.40 0.33 0.25 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 L：1kHz， Q：0.0796MHz EHS Nominal inductance ［μH］ Inductance tolerance DC Resistance ［Ω］（max.） Rated current ［A］（max.） Inductance Measuring frequency ［MHz］ RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 10 15 22 33 47 68 100 150 220 330 470 680 1000 ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ 0.038 0.049 0.075 0.094 0.15 0.23 0.30 0.47 0.70 0.88 1.3 1.9 3.2 2.5 2.2 1.9 1.7 1.3 1.0 0.90 0.78 0.63 0.58 0.46 0.38 0.30 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.252 EHS Nominal inductance ［μH］ Inductance tolerance DC Resistance ［Ω］（max.） Rated current ［A］（max.） Inductance Measuring frequency ［MHz］ RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS RoHS 15 22 33 47 68 100 150 220 330 470 680 1000 ±20％ ±20％ ±20％ ±20％ ±20％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ 0.035 0.050 0.070 0.081 0.12 0.16 0.24 0.38 0.46 0.69 1.1 1.8 3.3 2.7 2.4 2.1 1.7 1.6 1.3 0.95 0.89 0.74 0.58 0.46 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.252 EHS Nominal inductance ［μH］ Inductance tolerance DC Resistance ［Ω］（max.） Rated current ［A］（max.） Inductance Measuring frequency ［MHz］ ±20％ ±20％ ±20％ ±20％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ 0.019 0.025 0.027 0.035 0.045 0.062 0.091 0.14 0.20 0.31 0.47 0.58 0.94 5.2 5.1 4.6 4.0 3.4 3.1 2.3 1.9 1.5 1.3 1.0 0.98 0.74 1 1 1 1 1 1 1 1 1 1 1 1 1 ／ LEADED INDUCTORS INDUCTORS EHS ●LHLP10 Parts number LH LP10[]100M LH LP10[]150M LH LP10[]220M LH LP10[]330M LH LP10[]470M LH LP10[]680M LH LP10[]101K LH LP10[]151K LH LP10[]221K LH LP10[]331K LH LP10[]471K LH LP10[]681K LH LP10[]102K ●LHLP12NB Parts number LH LP12NB150M LH LP12NB220M LH LP12NB330M LH LP12NB470M LH LP12NB680M LH LP12NB101K LH LP12NB151K LH LP12NB221K LH LP12NB331K LH LP12NB471K LH LP12NB681K LH LP12NB102K ●LHLP16NB Parts number LH LP16NB100M RoHS 10 LH LP16NB150M RoHS 15 LH LP16NB220M RoHS 22 LH LP16NB330M RoHS 33 LH LP16NB470K RoHS 47 LH LP16NB680K RoHS 68 LH LP16NB101K RoHS 100 LH LP16NB151K RoHS 150 LH LP16NB221K RoHS 220 LH LP16NB331K RoHS 330 LH LP16NB471K RoHS 470 LH LP16NB681K RoHS 680 LH LP16NB102K RoHS 1000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) i_leaded_LH_e-E02R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 87 ■PARTS NUMBER ●LHLC08 Parts number EHS Nominal inductance ［μH］ ／ LEADED INDUCTORS INDUCTORS LH LC08[]1R0N RoHS 1.0 LH LC08[]1R5M RoHS 1.5 LH LC08[]2R2M RoHS 2.2 LH LC08[]2R7M RoHS 2.7 LH LC08[]3R3M RoHS 3.3 LH LC08[]3R9M RoHS 3.9 LH LC08[]4R7M RoHS 4.7 LH LC08[]5R6M RoHS 5.6 LH LC08[]6R8M RoHS 6.8 LH LC08[]8R2M RoHS 8.2 LH LC08[]100K RoHS 10 LH LC08[]120K RoHS 12 LH LC08[]150K RoHS 15 LH LC08[]180K RoHS 18 LH LC08[]220K RoHS 22 LH LC08[]270K RoHS 27 LH LC08[]330K RoHS 33 LH LC08[]390K RoHS 39 LH LC08[]470K RoHS 47 LH LC08[]560K RoHS 56 LH LC08[]680K RoHS 68 LH LC08[]820K RoHS 82 LH LC08[]101K RoHS 100 LH LC08[]121K RoHS 120 LH LC08[]151K RoHS 150 LH LC08[]181K RoHS 180 LH LC08[]221K RoHS 220 LH LC08[]271K RoHS 270 LH LC08[]331K RoHS 330 LH LC08[]391K RoHS 390 LH LC08[]471K RoHS 470 LH LC08[]561K RoHS 560 LH LC08[]681K RoHS 680 LH LC08[]821K RoHS 820 LH LC08[]102J RoHS 1000 LH LC08[]122J RoHS 1200 LH LC08[]152J RoHS 1500 LH LC08[]182J RoHS 1800 LH LC08[]222J RoHS 2200 LH LC08[]272J RoHS 2700 LH LC08[]332J RoHS 3300 LH LC08[]392J RoHS 3900 LH LC08[]472J RoHS 4700 LH LC08[]562J RoHS 5600 LH LC08[]682J RoHS 6800 LH LC08[]822J RoHS 8200 LH LC08[]103J RoHS 10000 LH LC08[]123J RoHS 12000 LH LC08[]153J RoHS 15000 LH LC08[]183J RoHS 18000 LH LC08[]223J RoHS 22000 LH LC08[]273J RoHS 27000 LH LC08[]333J RoHS 33000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) Inductance tolerance Q （min.） Self-resonant frequency ［MHｚ］（min..） DC Resistance ［Ω］（max.） Rated current ［A］（max.） Measuring frequency ［MHz］ ±30％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ 40 40 40 40 40 40 40 40 40 40 65 65 50 50 50 50 40 40 40 40 35 35 25 25 20 35 35 25 25 20 25 25 25 30 55 45 55 55 55 55 55 55 65 65 65 65 60 60 60 60 60 60 60 76 65 56 48 41 33 30 23 21 19 17 16 13 12 11 10 8.8 8.4 8.2 7.9 7.0 6.5 5.7 5.2 4.7 4.2 3.7 3.5 3.2 2.9 2.4 2.2 2.0 1.6 1.5 1.4 1.3 1.2 1.1 1.0 0.85 0.78 0.68 0.62 0.61 0.60 0.48 0.44 0.35 0.30 0.28 0.25 0.23 0.013 0.014 0.017 0.019 0.021 0.024 0.025 0.028 0.030 0.034 0.041 0.044 0.053 0.060 0.068 0.091 0.10 0.12 0.15 0.17 0.20 0.22 0.32 0.36 0.41 0.66 0.73 0.85 0.97 1.1 1.3 1.5 1.8 2.3 2.7 3.2 4.1 4.8 5.6 7.5 8.5 9.7 14 16 18 20 32 36 62 72 82 90 100 5.4 5.2 4.8 4.2 3.8 3.7 3.6 3.5 3.4 3.0 2.9 2.8 2.6 2.4 2.3 2.0 1.9 1.7 1.5 1.4 1.3 1.2 1.0 0.96 0.88 0.71 0.66 0.63 0.59 0.55 0.49 0.47 0.44 0.38 0.35 0.31 0.29 0.26 0.23 0.21 0.19 0.18 0.16 0.15 0.14 0.13 0.11 0.084 0.068 0.066 0.057 0.054 0.053 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz i_leaded_LH_e-E02R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 88 14 ■PARTS NUMBER ●LHLC10 Parts number EHS Nominal inductance ［μH］ Q （min.） Self-resonant frequency ［MHｚ］（min..） DC Resistance ［Ω］（max.） Rated current ［A］（max.） Measuring frequency ［MHz］ ±20％ ±20％ ±20％ ±20％ ±20％ ±20％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±10％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ ±5％ 50 50 50 50 50 50 90 90 90 90 60 60 60 60 50 50 40 40 40 40 40 40 40 30 30 30 30 30 30 30 50 50 50 50 50 50 50 50 50 50 50 50 60 60 60 60 60 40 40 40 40 30 30 30 30 30 30 46 40 38 34 30 24 19 16 12 9.2 8.6 7.1 6.8 6.7 6.2 5.2 4.6 4.7 3.8 3.2 2.9 2.6 2.3 2.1 2.0 1.8 1.7 1.5 1.4 1.3 1.2 0.87 0.83 0.75 0.70 0.67 0.56 0.54 0.49 0.41 0.38 0.36 0.29 0.27 0.24 0.21 0.20 0.15 0.14 0.13 0.12 0.10 0.095 0.088 0.085 0.070 0.069 0.019 0.022 0.024 0.025 0.028 0.031 0.034 0.038 0.042 0.046 0.061 0.069 0.078 0.085 0.093 0.10 0.12 0.13 0.18 0.25 0.29 0.40 0.44 0.50 0.56 0.62 0.84 0.93 1.0 1.4 1.8 2.3 2.7 3.0 3.9 4.3 5.8 6.4 7.1 9.0 10 12 19 21 34 38 43 67 76 84 96 170 200 210 240 260 300 5.0 4.8 4.7 4.5 4.1 3.9 3.6 3.4 3.2 3.0 2.8 2.7 2.6 2.4 2.3 2.1 2.0 1.8 1.5 1.3 1.2 1.0 0.97 0.90 0.86 0.75 0.65 0.61 0.57 0.50 0.48 0.40 0.37 0.36 0.32 0.30 0.26 0.25 0.24 0.21 0.20 0.18 0.14 0.13 0.11 0.10 0.095 0.076 0.068 0.065 0.061 0.045 0.043 0.041 0.038 0.037 0.035 7.96 7.96 7.96 7.96 7.96 7.96 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 2.52 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.796 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 0.252 L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0796MHz L：1kHz， Q：0.0252MHz L：1kHz， Q：0.0252MHz L：1kHz， Q：0.0252MHz ／ LEADED INDUCTORS INDUCTORS LH LC10[]3R3M RoHS 3.3 LH LC10[]3R9M RoHS 3.9 LH LC10[]4R7M RoHS 4.7 LH LC10[]5R6M RoHS 5.6 LH LC10[]6R8M RoHS 6.8 LH LC10[]8R2M RoHS 8.2 LH LC10[]100K RoHS 10 LH LC10[]120K RoHS 12 LH LC10[]150K RoHS 15 LH LC10[]180K RoHS 18 LH LC10[]220K RoHS 22 LH LC10[]270K RoHS 27 LH LC10[]330K RoHS 33 LH LC10[]390K RoHS 39 LH LC10[]470K RoHS 47 LH LC10[]560K RoHS 56 LH LC10[]680K RoHS 68 LH LC10[]820K RoHS 82 LH LC10[]101K RoHS 100 LH LC10[]121K RoHS 120 LH LC10[]151K RoHS 150 LH LC10[]181K RoHS 180 LH LC10[]221K RoHS 220 LH LC10[]271K RoHS 270 LH LC10[]331K RoHS 330 LH LC10[]391K RoHS 390 LH LC10[]471K RoHS 470 LH LC10[]561K RoHS 560 LH LC10[]681K RoHS 680 LH LC10[]821K RoHS 820 LH LC10[]102J RoHS 1000 LH LC10[]122J RoHS 1200 LH LC10[]152J RoHS 1500 LH LC10[]182J RoHS 1800 LH LC10[]222J RoHS 2200 LH LC10[]272J RoHS 2700 LH LC10[]332J RoHS 3300 LH LC10[]392J RoHS 3900 LH LC10[]472J RoHS 4700 LH LC10[]562J RoHS 5600 LH LC10[]682J RoHS 6800 LH LC10[]822J RoHS 8200 LH LC10[]103J RoHS 10000 LH LC10[]123J RoHS 12000 LH LC10[]153J RoHS 15000 LH LC10[]183J RoHS 18000 LH LC10[]223J RoHS 22000 LH LC10[]273J RoHS 27000 LH LC10[]333J RoHS 33000 LH LC10[]393J RoHS 39000 LH LC10[]473J RoHS 47000 LH LC10[]563J RoHS 56000 LH LC10[]683J RoHS 68000 LH LC10[]823J RoHS 82000 LH LC10[]104J RoHS 100000 LH LC10[]124J RoHS 120000 LH LC10[]154J RoHS 150000 ・ [] Please specify the packaging code. (TB: Taping, NB: Bulk) Inductance tolerance i_leaded_LH_e-E02R01 ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . 14 89 RADIAL LEADED INDUCTORS ■PACKAGING ①Minimum Quantity Box － － － 500 500 300 200 － － Standard quantity [pcs] Bulk 100 50 25 － － － － 100 50 Taped 1000 500 500 250 200 － － 1000 500 φD（max） 9.0 （0.354） 11.0 （0.433） 14.0 （0.551） 17.0 （0.669） H2（max） 9.5 （0.374） 14.0 （0.551） 17.0 （0.669） 21.0 （0.827） Dimensions F＊ 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 7.5±1.0 （0.295±0.039） 7.5±1.0 （0.295±0.039） ℓ 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） φd 0.6±0.05 （0.024±0.002） 0.6±0.05 （0.024±0.002） 0.8±0.05 （0.031±0.002） 0.8±0.05 （0.031±0.002） Unit：mm（inch） H2（max） 11.0 （0.433） 16.0 （0.624） 19.0 （0.741） Dimensions F＊ 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 7.5±1.0 （0.295±0.039） ℓ 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） φd 0.6±0.05 （0.024±0.004） 0.6±0.05 （0.024±0.004） 0.8±0.05 （0.031±0.004） Unit：mm（inch） Type (EIA) LHL 08 LHL 10 LHL 13 LHL 16 LHLP10 LHLP12NB LHLP16NB LHLC08 LHLC10 ②Bulk dimensions ●LHL08～16 Type LHL08 LHL10 LHL13 LHL16 *Measured at the base of the leads. ●LHLP10～16 Type LHLP10 LHLP12 LHLP16 φD（max） 11.0 （0.433） 13.0 （0.512） 17.0 （0.669） *Measured at the base of the leads. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_LH_pack_e-E02R01 ●LHL08～16 D H1 H H2 P P0 P1 P2 F h W W0 W1 W2 D0 φd t LHL08 φ9.0 max （φ0.354 max） 30.5 max （1.20 max） 18.0＋2.0/－0.0 （0.709＋0.079/－0.000） 9.5 max （0.374 max） 12.7±1.0 （0.500±0.039） 12.7±0.3※1 （0.500±0.012） 3.85±0.7 （0.152±0.028） 6.35±1.3 （0.250±0.051） 5.0＋0.8/－0.2 （0.197＋0.031/－0.008） 0.0±2.0 （0.0±0.079） 18.0＋1.0/－0.5 （0.709＋0.039/－0.020） 12.5 min （0.492 min） 9.0±0.5 （0.354±0.020） 3.0 max※2 （0.118 max） φ4.0±0.2 （φ0.158±0.008） φ0.6±0.05 （φ0.024±0.002） 0.6±0.3 （0.024±0.012） LHL10 φ11.0 max （φ0.433 max） 34.0 max （1.34 max） 18.0＋2.0/－0.0 （0.709＋0.079/－0.000） 14.0 max （0.551 max） 12.7±1.0 （0.500±0.039） 12.7±0.3※1 （0.500±0.012） 3.85±0.7 （0.152±0.028） 6.35±1.3 （0.250±0.051） 5.0＋0.8/－0.2 （0.197＋0.031/－0.008） 0.0±2.0 （0.0±0.079） 18.0＋1.0/－0.5 （0.709＋0.039/－0.020） 12.5 min （0.492 min） 9.0±0.5 （0.354±0.020） 3.0 max※2 （0.118 max） φ4.0±0.2 （φ0.158±0.008） φ0.6±0.05 （φ0.024±0.002） 0.6±0.3 （0.024±0.012） LHL13 φ14.0 max （φ0.551 max） 37.0 max （1.46 max） 18.0＋2.0/－0.0 （0.709＋0.079/－0.000） 17.0 max （0.669 max） 15.0±1.0 （0.591±0.039） 15.0±0.3※1 （0.591±0.012） 3.75±0.7 （0.148±0.028） 7.50±1.3 （0.295±0.051） 7.50＋0.8/－0.2 （0.295＋0.031/-0.008） 0.0±2.0 （0.0±0.079） 18.0＋1.0/－0.5 （0.709＋0.039/－0.020） 12.5 min （0.492 min） 9.0±0.5 （0.354±0.020） 3.0 max※2 （0.118 max） φ4.0±0.2 （φ0.158±0.008） φ0.8±0.05 （φ0.031±0.002） 0.6±0.3 （0.024±0.012） LHL16 φ17.0 max （φ0.669 max） 41.0 max （1.61 max） 18.0＋2.0/－0.0 （0.709＋0.079/－0.000） 21.0 max （0.827 max） 30.0±1.0 （1.18±0.039） 15.0±0.3※1 （0.591±0.012） 3.75±0.7 （0.148±0.028） 7.50±1.3 （0.295±0.051） 7.50±0.5 （0.295±0.020） 0.0±2.0 （0.0±0.079） 18.0＋1.0/－0.5 （0.709＋0.039/－0.020） 12.5 min （0.492 min） 9.0±0.5 （0.354±0.020） 3.0 max※2 （0.118 max） φ4.0±0.2 （φ0.158±0.008） φ0.8±0.05 （φ0.031±0.002） 0.6±0.3 （0.024±0.012） Unit：mm（inch） ※1 Accumulated error for 20 pitches is 1mm. ※2 Bonding tape must not protrude from the base tape. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_LH_pack_e-E02R01 ●LHLP10TB Type Symbol D H1 H H2 LHLP10 P P0 P1 P2 F Dimensions φ11.0 max （φ0.433 max） 32.0 max （1.26 max） 18.0＋2.0/－0.0 （0.709＋0.079/－0.000） 11.0 max （0.433 max） 12.7±1.0 （0.500±0.039） 12.7±0.3※1 （0.500±0.012） 3.85±0.7 （0.152±0.028） 6.35±1.3 （0.250±0.051） 5.0＋0.8/－0.2 （0.197＋0.031/－0.008） Symbol h W W0 W1 W2 D0 φd t Dimensions 0.0±2.0 （0.0±0.079） 18.0＋1.0/－0.5 （0.709＋0.039/－0.020） 12.5 min （0.492 min） 9.0±0.5 （0.354±0.020） 3.0 max※2 （0.118 max） φ4.0±0.2 （φ0.158±0.008） φ0.6±0.05 （φ0.024±0.002） 0.6±0.3 （0.024±0.012） Unit： mm（inch） ※1 Accumulated error for 20 pitches is 1mm. ※2 Bonding tape must not protrude from the base tape. ●LHLC08, LHLC10 Type LHLC08 LHLC10 φD（max） 9.0 （0.354） 11.0 （0.433） H2（max） 9.5 （0.374） 14.0 （0.551） Dimensions F＊ 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） ℓ 5.0±1.0 （0.197±0.039） 5.0±1.0 （0.197±0.039） φd 0.6±0.05 （0.024±0.002） 0.6±0.05 （0.024±0.002） Unit：mm（inch） *Measured at the base of the leads. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_LH_pack_e-E02R01 D H1 H H2 P P0 P1 P2 F H W W0 W1 W2 D0 φd t LHLC08 φ9.0max (φ0.354max） 30.5max （1.20max） 18.0＋2.0/－0.0 （0.709＋0.079/－0.000） 9.5max （0.374max） 12.7±1.0 （0.500±0.039） 12.7±0.3※1 （0.500±0.012） 3.85±0.7 （0.152±0.028） 6.35±1.3 （0.250±0.051） 5.0＋0.8/－0.2 （0.197＋0.031/－0.008） 0.0±2.0 （0.0±0.079） 18.0＋1.0/－0.5 （0.709＋0.039/－0.020） 12.5min （0.492min） 9.0±0.5 （0.354±0.020） 3.0max※2 （0.118max） φ4.0±0.2 （φ0.158±0.008） φ0.6±0.05 （φ0.024±0.002） 0.6±0.3 （0.024±0.012） LHLC10 φ11.0max （φ0433max） 34.0max （1.34max） 18.0＋2.0/－0.0 （0.709＋0.079/－0.000） 14.0max （0.551max） 12.7±1.0 （0.500±0.039） 12.7±0.3※1 （0.500±0.012） 3.85±0.7 （0.152±0.028） 6.35±1.3 （0.250±0.051） 5.0＋0.8/－0.2 （0.197＋0.031/－0.008） 0.0±2.0 （0.0±0.079） 18.0＋1.0/－0.5 （0.709＋0.039/－0.020） 12.5min （0.492min） 9.0±0.5 （0.354±0.020） 3.0max※2 （0.118max） φ4.0±0.2 （φ0.158±0.008） φ0.6±0.05 （φ0.024±0.002） 0.6±0.3 （0.024±0.012） Unit：mm（inch） ※1 Accumulated error for 20 pitches is 1mm. ※2 Bonding tape must not protrude from the base tape. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_LH_pack_e-E02R01 AXIAL LEADED INDUCTORS（CAL Type）、 RADIAL LEADED INDUCTORS（LH Type）、 LEADED FERRITE BEAD INDUCTORS（ FB Series A Type／R Type） ■RELIABILITY DATA 1. Operating temperature Range CAL45 Type Specified Value －25～＋ 105℃ LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type LHL□□□ －25～＋ 85℃ : Including self-generated heat : Including self-generated heat 2. Storage temperature Range CAL45 Type Specified Value LHL□□□ －40～＋ 85℃ FBA/FBR 3. Rated current CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks CAL45 Type : The maximum DC value having inductance within 10% and temperature increase within 40℃ by the application of DC bias. LHL□□□ : The maximum DC value having inductance decrease within 10% (LHLC08, LHLC10：within 30%) and temperature increase within the following specified temperature by the application of DC bias. Reference temperature : 25℃（LHL08, LHL10, LHL13） : 30℃（LHL16, LHLP□□） : 40℃（LHLC08, LHLC10） FBA/FBR : No disconnection or appearance abnormality by continuous current application for 30 min. Change after the application shall be within ±20% of the initial value. This is not guaranteed for electrical characteristics during current application. 4. Impedance CAL45 Type Specified Value LHL□□□ FBA/FBR Test Methods and Remarks FBA/FBR : Measuring equipment Measuring frequency Within the specified tolerance : Impedance analyzer (HP4191A) or its equivalent : Specified frequency 5. Inductance CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks CAL45 Type : Measuring equipment Measuring frequency LHL□□□ : Measuring equipment Measuring frequency : LCR meter (HP4285A + HP42851A or its equivalent) : Specified frequency : LCR meter (HP4285A＋HP42851A or its equivalent) : LCR meter (HP4263A) or its equivalent (at 1kHz) : Specified frequency ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 6. Q CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks LHL□□□ (except LHLP) : Measuring equipment : LCR meter (HP4285A＋HP42851A or its equivalent) : LCR meter (HP4263A) or its equivalent (at 1kHz) Measuring frequency : Specified frequency 7. DC Resistance CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks Measuring equipment : DC ohmmeter 8. Self resonance frequency CAL45 Type Specified Value LHL□□□ Within the specified tolerance FBA/FBR Test Methods and Remarks LHL□□□(except LHLP) : Measuring equipment : (HP4191A, 4192A) its equivalent 9. Temperature characteristic CAL45 Type Specified Value LHL□□□ △L/L : Within ±7% (except LHLP16 : Within ±20%) FBA/FBR Test Methods and Remarks Change of maximum inductance deviation in step 1 to 5 Temperature (℃) Step LHL□□□ 1 20 2 Minimum operating temperature 3 20 (Standard temperature) 4 Maximum operating temperature 5 20 10. Tensile strength test CAL45 Type Specified Value LHL□□□ No abnormality such as cut lead, or looseness. FBA/FBR Test Methods and Remarks CAL45 Type : Apply the stated tensile force progressively in the direction to draw terminal. force (N) duration (s) 10 10 LHL□□□ : Apply the stated tensile force progressively in the direction to draw terminal. Nominal wire diameter tensile φd (mm) force (N) duration (s) 0.3＜φd≦0.5 5 30±5 0.5＜φd≦0.8 10 0.8＜φd≦1.2 25 FBA/FBR : The body of a component shall be fixed and a tensile force of 20±1N shall be applied to the lead wire in the of the component during 10±1 seconds. axial direction ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 11. Over current Specified Value CAL45 Type No emission of smoke no firing. LHL□□□ There shall be no scorch or short of wire. LHLC08, LHLC10 : There shall be no firing. FBA/FBR Test Methods and Remarks LHL□□□・CAL45 Type ： Measuring current : Rated current×2 Duration : 5 min. Number of measuring : one time 12. Terminal strength : bending CAL45 Type Specified Value LHL□□□ No abnormality such as cut lead, or looseness. FBA/FBR CAL45 Type : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter Mass reference Bending force tensile weight 0.3＜ φ d≦0.5 2.5 0.25 0.5＜ φ d≦0.8 5 0.50 Test Methods and Remarks LHL□□□・FBA/FBR : Suspend a weight of specified mass at the end of the terminals and incline the body through the angle of 90 degrees and return it to the initial position. This operation is done over a period of 2-3 sec. Then second bend in the opposite direction shall be made. Number of bends : Two times. Nominal wire diameter Mass reference Bending force tensile weight 0.3＜φd≦0.5 2.5 0.25 0.5＜φd≦0.8 5 0.5 0.8＜φd≦1.2 10 1.0 13. Insulation resistance : between the terminals and body CAL45 Type Specified Value LHL□□□ 100MΩ min. FBA/FBR Test Methods and Remarks LHL□□□ : Applied voltage Duration : 500 VDC : 60 sec. 14. Insulation resistance : between terminals and core CAL45 Type Specified Value LHL□□□ FBA/FBR Test Methods and Remarks FBA/FBR : Applied voltage Duration 1MΩ min. : 100 VDC : 60±5 sec. 15. Withstanding : between the terminals and body CAL45 Type Specified Value LHL□□□ No abnormality such as insulation damage FBA/FBR Test Methods and Remarks LHL□□□ : According to JIS C5102. 7. 1. 3 (C) Metal global method Applied voltage : 500 VDC Duration : 60 sec. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 16. DC bias characteristic CAL45 Type Specified Value △L/L : Within －10% LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Measure inductance with application of rated current using LCR meter to compare it with the initial value. 17. Body strength CAL45 Type Specified Value No abnormality as damage. LHL□□□ FBA/FBR CAL45 Type : Applied force Duration Speed FBA : Applied force Duration No abnormality such as cracks on body. :50N : 10 sec. : Shall attain to specified force in 2 sec. : 50±3N : 30±1 sec. Test Methods and Remarks 18. Resistance to vibration Specified Value Test Methods and Remarks CAL45 Type △L/L : Within ±5% LHL□□□ Appearance : No abnormality △L/L : Within ±5% Q change : Within ±30% (LHLP : only △L/L) FBA/FBR Appearance : No abnormality Impedance change : Within ±20% CAL45 Type : Directions : 2 hrs each in X, Y and Z directions total : 6hrs. Frequency range : 10 to 55 to 10Hz (1min.) Amplitude : 1.5mm Mounting method : Soldering onto printed board. Recovery : At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. LHL□□□・FBA/FBR : Directions : 2 hrs each in X, Y and Z directions total : 6hrs. Frequency range : 10 to 55 to 10Hz (1min.) Amplitude : 1.5mm Mounting method : Soldering onto printed board. 19. Resistance to shock CAL45 Type Specified Value No significant abnormality in appearance LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Drop test Impact material Height Total number of drops : concrete or vinyl tile : 1m : 10 times ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 20. Solderability Specified Value Test Methods and Remarks CAL45 Type At least 75％ of terminal electrode is covered by new solder. LHL□□□ At least 75％ of terminal electrode is covered by new solder. FBA/FBR At least 90％ of terminal electrode is covered by new solder. CAL45 Type : Solder temperature Duration LHL□□□ : Solder temperature Duration Immersion depth FBA/FBR : Solder temperature Duration Immersion depth : 230±5℃ : 2±0.5 sec. : 235±5℃ : 2±0.5 sec. : Up to 1.5mm from bottom of case. : 230±5℃ : 3±1 sec. : Up to 1.5mm from terminal root. 21. Resistance to soldering heat Specified Value CAL45 Type △L/L : Within ±5% LHL□□□ No significant abnormality in appearance Inductance change : Within ±5% Q change : Within ±30%(LHLP : only △L/L) FBA/FBR No significant abnormality in appearance Impedance change : Within ±20% CAL45 Type : Solder temperature Duration Immersed conditions Recovery : : : : LHL□□□ : Solder bath method : 270±5℃ 5±0.5 sec. One time Inserted into substrate with t=1.6mm At least 1hr of recovery under the standard condition after the test, followed by the measurement within 2hrs. Solder temperature Duration Manual soldering : Caution Recovery : : : : : : : : 260±5℃ 10±1 sec. Up to 1.5mm from the bottom of case. 350±10℃ (At the tip of soldering iron) 5±1 sec. Up to 1.5mm from the bottom of case. No excessive pressing shall be applied to terminals. 4 to 24hrs of recovery under the standard condition after the test. Solder temperature Duration Immersion depth Solder temperature Duration Immersion depth Recovery : : : : : : : 260±5℃ 10±1 sec. Up to 1.5mm from the terminal root. 350±5℃ 3±1 sec. Up to 1.5mm from the terminal root. 3hrs of recovery under the standard condition after the test. Solder temperature Duration Test Methods and Remarks FBA/FBR : Solder bath method: Condition 1: Condition 2 : 22. Resistance to solvent CAL45 Type Specified Value Please avoid the ultrasonic cleaning of this product. LHL□□□ No significant abnormality in appearance Impedance change : Within ±20% FBA/FBR Test Methods and Remarks FBA/FBR : Solvent temperature Duration Solvent type Recovery : : : : 20～25℃ 30±5 sec. Acetone 3hrs of recovery under the standard condition after the test. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 23. Thermal shock Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP：only △L/L) FBA/FBR Appearance : No abnormality Impedance change : Within ±20% CAL45 Type：Conditions for 1cycle Step Temperature (℃) 1 －25＋0/－3 2 Room temperature 3 ＋85＋2/－0 4 Room temperature Number of cycles Recovery Test Methods and Remarks Duration (min.) 30±3 Within 3 30±3 Within 3 : 5 cycles : At least 1hr of recovery under the standard condition after the removal from test chamber, followed by the measurement within 2hrs. LHL□□□・FBA/FBR： According to JIS C0025 Conditions for 1 cycle Step Temperature (℃) 1 Minimum operating temperature＋0/－3 2 Room temperature 3 Minimum operating temperature＋2/－0 4 Room temperature Number of cycles Recovery : : : : Duration (min.) 30±3 Within 3 30±3 Within 3 10 cycles 〔LHL□□□〕 5 cycles (FBA/ FBR) 4 to 24hrs of recovery under the standard condition after the removal from the test chamber. 〔LHL□□□〕 3hrs of recovery under the standard condition after the removal from the test chamber. (FBA/ FBR) 24. Damp heat CAL45 Type Specified Value △L/L : Within ±10% LHL□□□ Appearance：No abnormality Impedance change：Within ±20% FBA/FBR Test Methods and Remarks CAL45 Type : Temperature Humidity Duration Recovery FBA/FBR : Temperature Humidity Duration Recovery : 40±2℃ : 90～95%RH : 1000 hrs : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. : : : : 60±2℃ 90～95%RH 1000 hrs 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 25. Loading under damp heat Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L) FBA/FBR Test Methods and Remarks CAL45 Type : Temperature Humidity Duration Applied current Recovery LHL□□□ : Temperature Humidity Duration Applied current Recovery : 40±2℃ : 90～95%RH : 1000 hrs : Rated current : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. : : : : : 40±2℃ 90～95%RH 1000＋48/-0 hrs Rated current 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 26. Loading at high temperature CAL45 Type Specified Value △L/L : Within ±10% LHL□□□ FBA/FBR Test Methods and Remarks CAL45 Type : Temperature Duration Applied current Recovery : 85±2℃ : 1000 hrs : Rated current : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. 27. Low temperature life test Specified Value CAL45 Type △L/L : Within ±10% LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L) FBA/FBR Test Methods and Remarks CAL45 Type : Temperature Duration Recovery LHL□□□ : Temperature Duration Recovery : －25±2℃ : 1000 hrs : At least 1hr of recovery under the standard removal from test chamber, followed by the measurement within 2hrs. :－40±3℃ : 1000＋48/-0 hrs : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. 28. High temperature life test CAL45 Type Specified Value LHL□□□ Appearance : No abnormality Inductance change : Within ±10% Q change : Within ±30% (LHLP : only △L/L) FBA/FBR Test Methods and Remarks LHL□□□ : Temperature Duration Recovery : 105±2℃ : 1000＋48/-0 hrs : 1 to 2hrs of recovery under the standard condition after the removal from the test chamber. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_reli_e-E02R01 AXIAL LEADED INDUCTORS（CAL Type）、 RADIAL LEADED INDUCTORS（LH Type）、 LEADED FERRITE BEAD INDUCTORS（FB Series A Type／R Type） ■PRECAUTIONS 1. Circuit Design Precautions ◆Operating environment 1. The products described in this specification are intended for use in general electronic equipment,(office supply equipment, telecommunications systems, measuring equipment, and household equipment). They are not intended for use in mission-critical equipment or systems requiring special quality and high reliability (traffic systems, safety equipment, aerospace systems, nuclear control systems and medical equipment including life-support systems,) where product failure might result in loss of life, injury or damage. For such uses, contact TAIYO YUDEN Sales Department in advance. 2. PCB Design Precautions Technical considerations ◆Design 1. Please design insertion pitches as matching to that of leads of the component on PCBs. ◆Design 1. When Inductors are mounted onto a PC board, hole dimensions on the board should match the lead pitch of the component, if not, it will cause breakage of the terminals or cracking of terminal roots covered with resin as excess stress travels through the terminal legs. 3. Considerations for automatic placement Precautions Technical considerations ◆Adjustment of mounting machine 1. Excessive impact load should not be imposed on the products when mounting onto the PC boards. 2. Mounting and soldering conditions should be checked beforehand. ◆Adjustment of mounting machine 1. When installing products, care should be taken not to apply distortion stress as it may deform the products. 4. Soldering Precautions ◆Wave soldering 1. Please refer to the specifications in the catalog for a wave soldering. 2. Do not immerse the entire inductor in the flux during the soldering operation. ◆Lead free soldering 1. When using products with lead free soldering, we request to use them after confirming adhesion, temperature of resistance to soldering heat, soldering etc sufficiently. ◆Recommended conditions for using a soldering iron: ・Put the soldering iron on the land-pattern. ・Soldering iron's temperature - Below 350℃ ・Duration - 3 seconds or less ・The soldering iron should not directly touch the inductor. ◆Reflow soldering 1. As for reflow soldering, please contact our sales staff. Technical considerations ◆Lead free soldering 1. If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. ◆Recommended conditions for using a soldering iron If products are used beyond the range of the recommended conditions, heat stresses may deform the products, and consequently degrade the reliability of the products. 5. Cleaning Precautions Technical considerations ◆Cleaning conditions 1. CAL type, LH type Please do not do cleaning by a supersonic wave. ◆Cleaning conditions 1. CAL type, LH type, If washing by supersonic waves, supersonic waves may deform products. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_prec_e-E02R01 6. Handling Precautions Technical considerations ◆Handling 1. Keep the inductors away from all magnets and magnetic objects. ◆Mechanical considerations 1. Please do not give the inductors any excessive mechanical shocks. 2. LH type If inductors are dropped onto the floor or a hard surface they should not be used. ◆Packing 1. Please do not give the inductors any excessive mechanical shocks. In loading, please pay attention to handling indication mentioned in a packing box (a loading direction / number of maximum loading / fragile item). ◆Handling 1. There is a case that a characteristic varies with magnetic influence. ◆Mechanical considerations 1. There is a case to be damaged by a mechanical shock. 2. LH type There is a case to be broken by a fall. ◆Packing 1. There is a case that a lead wire could be deformed by a fall or an excessive shock. 7. Storage conditions Precautions ◆Storage 1. To maintain the solderability of terminal electrodes and to keep the packing material in good condition, temperature and humidity in the storage area should be controlled. Recommended conditions ・Ambient temperature 0～40℃ ・Humidity Below 70% RH The ambient temperature must be kept below 30℃. Even under ideal storage conditions, solderability of products electrodes may decrease as time passes. For this reason, inductors should be used within one year from the time of delivery. In case of storage over 6 months, solderability shall be checked before actual usage. Technical considerations ◆Storage 1. Under a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of terminal electrodes and deterioration of taping/packaging materials may take place. ▶ This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification. For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) . i_leaded_prec_e-E02R01 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Taiyo Yuden: LHL08NB100K LHL08NB101K LHL08NB102J LHL08NB103J LHL08NB120K LHL08NB121K LHL08NB122J LHL08NB123J LHL08NB150K LHL08NB151K LHL08NB152J LHL08NB153J LHL08NB180K LHL08NB181K LHL08NB182J LHL08NB183J LHL08NB1R0N LHL08NB1R5M LHL08NB220K LHL08NB221K LHL08NB222J LHL08NB223J LHL08NB270K LHL08NB271K LHL08NB272J LHL08NB273J LHL08NB2R2M LHL08NB2R7M LHL08NB330K LHL08NB331K LHL08NB332J LHL08NB333J LHL08NB390K LHL08NB391K LHL08NB392J LHL08NB3R3M LHL08NB3R9M LHL08NB470K LHL08NB471K LHL08NB472J LHL08NB4R7M LHL08NB560K LHL08NB561K LHL08NB562J LHL08NB5R6M LHL08NB680K LHL08NB681K LHL08NB682J LHL08NB6R8M LHL08NB820K LHL08NB821K LHL08NB822J LHL08NB8R2M LHL08TB100K LHL08TB101K LHL08TB102J LHL08TB103J LHL08TB120K LHL08TB121K LHL08TB122J LHL08TB123J LHL08TB150K LHL08TB151K LHL08TB152J LHL08TB153J LHL08TB180K LHL08TB181K LHL08TB182J LHL08TB183J LHL08TB1R0N LHL08TB1R5M LHL08TB220K LHL08TB221K LHL08TB222J LHL08TB223J LHL08TB270K LHL08TB271K LHL08TB272J LHL08TB273J LHL08TB2R2M LHL08TB2R7M LHL08TB330K LHL08TB331K LHL08TB332J LHL08TB333J LHL08TB390K LHL08TB391K LHL08TB392J LHL08TB3R3M LHL08TB3R9M LHL08TB470K LHL08TB471K LHL08TB472J LHL08TB4R7M LHL08TB560K LHL08TB561K LHL08TB562J LHL08TB5R6M LHL08TB680K LHL08TB681K