DATA SHEET GBU10A~GBU10K GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER GBU VOLTAGE - 50 to 800 Volts CURRENT - 10.0 Amperes FEATURES .880(22.3) .860(21.8) .310(7.90) .290(7.40) • Reliable low cost construction utilizing molded plastic technique • High temperature soldering guaranteed: 260°C/10 seconds/.375"(9.5mm) lead length at 5 lbs. (2.3kg) tension .075(1.90)R .085(2.16) .065(1.65) • Surge overload rating: 200 Amperes peak MECHANICAL DATA Case: Reliable low cost construction utilizing .100(2.54) .085(2.16) molded plastic technique .140(3.56) .130(3.30) .740(18.8) .720(18.3) .080(2.03) .060(1.52) • Ideal for printed circuit board .160(4.1) .140(3.5) .710(18.0) .690(17.5) • Plastic material has Underwriters Laboratory Flammability Classification 94V-O Unit: inch ( mm ) .040(1.02) .030(0.76) .022(0.56) .018(0.46) .080(2.03) .065(1.65) Terminals: Leads solderable per MIL-STD-202, Method 208 .190(4.83) .210(5.33) Mounting position: Any .050(1.27) .040(1.02) Mounting torque: 5 in. lb. Max. Weight: 0.15 ounce, 4.0 grams MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25°Cambient temperature unless otherwise specified. Resistive or inductive load, 60Hz. For Capacitive load derate current by 20%. UNIT GBU10A GBU10B GBU10D GBU10G GBU10J GBU10K Maximum Recurrent Peak Reverse Voltage 50 100 200 400 600 800 V Maximum RMS Input Voltage 35 70 140 280 420 560 V Maximum DC Blocking Voltage 50 100 200 400 600 800 V Maximum Average Forward TC=100°C 10.0 A 127 A2sec 200 Apk Maximum Instantaneous Forward Voltage Drop per element at 5.0A 1.0 Vpk Maximum Reverse Leakage at rated T A=25° CDc Blocking Voltage per element TC=100°C 5.0 500 µA µA Typical Thermal Resistance per leg(Note 2) RθJA 8.6 °C / W Typical Thermal Resistance per leg(Note 3) RθJC 3.1 °C / W -55+150 °C Rectified Output Current at I2t Rating for fusing ( t<8.35ms) Peak Forward Surge Current single sine-wave superimposed on rated load(JEDEC method) Operating and Storage Temperature Range, TJ,TSTG NOTES: 1. Recommended mounting position is to bolt down on heatsink with silicone thermal compound for maximum heat transfer with #6 screw. 2. Units Mounted in free air, no heatsink, P.C.B at 0.375"(9.5mm) lead length with 0.5 x 0.5"(12 x 12mm)copper pads. 3. Units Mounted on a 2.6 x 1.4" x 0.06" thick ( 6.5 x 3.5 x 0.15cm) AL plate. DATE : AUG.29.2002 PAGE . 1 INSTANTANEOUS FORWARD CURRENT, AMPERES AVERAGE FORWARD CURRENT AMPERES RATING AND CHARACTERISTIC CURVES HEAT-SINK MOUNTING, TC (4X4X0.15) INCH COPPER PLATE 60Hz RESISTIVE OR INDUCTIVE LOAD MOUNTED ON 0.5X0.5 INCH COPPER PC BOARD, TA 0.5"(12.7mm) LEAD LENGTH 5.0 TJ = 25 Pulse Width = 30uS 1% Duty Cycle INSTANTANEOUS FORWARD VOLTAGE, VOLTS TEMPERATURE Fig.1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT INSTANTNEOUS REVERSE CURRENT, MICROAMPERES FORWARD SURGE CURRENT, AMPERES pk (HALF SINE-WAVE) Fig.2 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PER ELEMENT 200 160 120 80 40 PERCENT OF PEAK REVERSE VOLTAGE CAPACITANCE, pF Fig.3 - TYPICAL REVERSE CHARACTERISTICS 0 NO. OF CYCLES AT 62Hz Fig.4 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT TJ = 25 f = 1MHz Visg = 50m Vp-p REVERSE VOLTAGE, VOLTS Fig.5 - TYPICAL JUNCTION CAPACITANCE PER ELEMENT DATE : AUG.29.2002 PAGE . 2