MIC94060/61/62/63 High Side Power Switches General Description Features The MIC94060-63 are high-side load switches designed for operation between 1.7V to 5.5V. The devices contain a low on-resistance P-channel MOSFET that supports over 2A of continuous current. The MIC94061 and MIC94063 features an active load discharge circuit which insures capacitive loads retain no charge when the main switch is in an OFF state. MIC94060-61 feature rapid turn on while MIC94062-63 provide a slew rate controlled Soft-Start turn-on of 800µs (typical) to prevent in-rush current from glitching supply rails. An active pull-down on the enable input keeps MIC94060-63 in a default OFF state until the EN pin is pulled to a high level. Built-in level shift circuitry allows low voltage logic signals to switch higher supply voltages, or vice versa; high level logic signals can control low level voltages. MIC94060-63’s operating voltage range makes them suitable for 1-cell Lithium ion and 2- to 3-cell NiMH/NiCad/Alkaline powered systems, as well as, all 5V applications. Their low operating current of 2µA and low shutdown current of <1µA maximize battery life. Data sheets and support documentation can be found on Micrel’s web site at: www.micrel.com. • • • • • • • • • 1.7V to 5.5V input voltage range 2A continuous operating current 77mΩ (typ) RDSON Built-in level shift for control logic; can be operated by 1.5V logic. Low 2µA quiescent current Soft-Start: MIC94062-63 Micro-power shutdown <1µA Load discharge circuit: MIC94061, MIC94063 Space saving 1.2mm x 1.6mm Thin MLF® package Applications • Load switch in portable applications: - Cellular phones - PDAs - MP3 players - Digital Cameras - Portable instrumentation • Battery switch-over circuits • Level translator ________________________________________________________________________________________________________ Typical Application MIC94060, 62 Load Switch Application MIC94061, 63 Load Switch with Capacitive Load Discharge MLF and MicroLeadFrame are registered trademarks of Amkor Technologies, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com July 2010 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 Ordering Information Part Marking(1) Part Number Standard Pb-Free MIC94060BC6 Soft-Start Standard Pb-Free MIC94060YC6 P54 P54 MIC94061BC6 MIC94061YC6 P55 P55 MIC94062BC6 MIC94062YC6 P56 P56 ● MIC94063BC6 MIC94063YC6 P57 P57 ● — MIC94060YMT — P54 — MIC94061YMT — P55 — MIC94062YMT — P56 ● — MIC94063YMT — P57 ● Load Discharge Package ● SC-70-6 ● ● 1.2mm x 1.6mm ® (2, 3) Thin MLF ● Notes 1. Underbar symbol on SC-70 Pb-free packages may not be to scale. 2. MLF ▲ = Pin 1 identifier. 3. MLF is a GREEN RoHS compliant package. Lead finish is NiPdAu. Mold compound is Halogen Free. ® ® Pin Configuration 1.2x1.6 mm Thin MLF® (MT) SC-70-6 (C6) Pin Description Pin Number Pin Name Pin Function SC-70 MLF 1 1 VOUT Drain of P-channel MOSFET. 2,5 2 GND Ground and the backside pad (MLF only) should both be connected to electrical ground. 4 3 VIN Source of P-channel MOSFET. 3 4 EN Enable (Input): Active-high CMOS compatible control input for switch A. Do not leave floating. 6 -- NIC No Internal Connection. A signal or voltage applied to this pin will have no effect on device operation. July 2010 2 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 Absolute Maximum Ratings (1) Operating Ratings (2) Input Voltage (VIN) ................................................+6V Enable Voltage (VEN) ...........................................+6V Continuous Drain Current (ID) (3) TA = 25°C ....................................................... ±2A TA = 85°C ....................................................±1.4A Pulsed Drain Current (IDP) (4) ................................ ±6A Continuous Diode Current (IS) (4) .....................–50mA Storage Temperature (Ts) ............... –55°C to +150°C ESD Rating – HBM (6) .......................................... 4KV Input Voltage (VIN)................................. +1.7 to +5.5V Junction Temperature (TA).............. –40°C to +125°C Package Thermal Resistance SC-70-6 (θJA)......................................... 240°C/W 1.2x1.6 MLF (θJA) .................................. 172°C/W 1.2x1.6 MLF (θJC) (3) .............................. 134°C/W Electrical Characteristics VIN = 5V; TA = 25°C, bold values indicate –40°C< TA < +85°C, unless noted. Symbol Parameter Condition Min VEN_TH Enable Threshold Voltage VIN = 1.8V to 4.5V, ID = –250μA VIN = 1.7V to 4.5V, ID = –250μA Typ Max Units 0.5 1.2 V 0.4 1.2 V 4 μA 1 μA IEN Enable Input Current VIN = VEN = 5.5V IVIN OFF State Leakage Current VIN = +5.5V, VEN = 0V RDS(ON) P-Channel Drain to Source ON Resistance VIN = +4.5V, ID = –100mA, VEN = 1.5V 77 110 mΩ VIN = +3.6V, ID = –100mA, VEN = 1.5V 85 115 mΩ VIN = +2.5V, ID = –100mA, VEN = 1.5V 100 140 mΩ VIN = +1.8V, ID = –100mA, VEN = 1.5V 145 200 mΩ VIN = +1.7V, ID = –100mA, VEN = 1.5V 155 215 mΩ VIN = +4.5V, ID = –100mA, VEN = 1.5V 85 115 mΩ VIN = +3.6V, ID = –100mA, VEN = 1.5V 100 140 mΩ VIN = +2.5V, ID = –100mA, VEN = 1.5V 145 200 mΩ VIN = +1.8V, ID = –100mA, VEN = 1.5V 155 215 mΩ VIN = +1.7V, ID = –100mA, VEN = 1.5V 165 225 mΩ VIN = +3.6V, ITEST = 1mA, VEN = 0V 200 300 Ω Typ Max Units 0.85 1.5 μs 700 1200 μs 0.5 1 5 μs 500 800 1500 μs SC-70 Package RDS(ON) P-Channel Drain to Source ON Resistance MLF Package RSHUTDOWN Turn-Off Resistance 2 MIC94061, 63 Dynamic Symbol Parameter Condition Min tON_DLY Turn-On Delay Time VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94060, 61 VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94062, 63 tON_RISE Turn-On Rise Time VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94060, 61 VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94062, 63 July 2010 3 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 Dynamic (Continued) tOFF_DLY Turn-Off Delay Time VIN = +3.6V, ID = –100mA, VEN = 1.5V 100 200 ns 60 200 ns 60 100 ns 60 100 ns MIC94060, 61 VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94062, 63 tOFF_FALL Turn-Off Fall Time VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94060, 61 VIN = +3.6V, ID = –100mA, VEN = 1.5V MIC94062, 63 Notes: 1. Exceeding the absolute maximum rating may damage the device. 2. The device is not guaranteed to function outside its operating rating. 3. With backside thermal contact to PCB. 4. Pulse width <300μs with < 2% duty cycle. 5. Continuous body diode current conduction (reverse conduction, i.e. VOUT to VIN) is not recommended. 6. Devices are ESD sensitive. Handling precautions recommended. HBM (Human body model), 1.5kΩ in series with 100pF. July 2010 4 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 Typical Characteristics July 2010 5 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 Functional Characteristics MIC94060 July 2010 6 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 MIC94061 July 2010 7 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 MIC94062 July 2010 8 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 MIC94063 July 2010 9 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 Package Information 6-Pin SC-70 (C6) 4-Pin Thin MLF® (MT) July 2010 10 M9999-070910-E Micrel, Inc. MIC94060/61/62/63 Recommended Land Pattern for MLF 1.2x1.6 4 Lead Optional for maximum thermal performance. Heatsink should be connected to GND plane of PCB for maximum thermal performance. Disclaimer: This is only a recommendation based on information available to Micrel from its suppliers. Actual land pattern may have to be significantly different due to various materials and processes used in PCB assembly. Micrel makes no representation or warranty of performance based on the recommended land pattern." MICREL, INC. 2180 FORTUNE DRIVE SAN JOSE, CA 95131 USA TEL +1 (408) 944-0800 FAX +1 (408) 474-1000 WEB http://www.micrel.com The information furnished by Micrel in this data sheet is believed to be accurate and reliable. However, no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser’s use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser’s own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. © 2004 Micrel, Incorporated. July 2010 11 M9999-070910-E