Optoway BTR-7780-1590-SPG 1590 nm tx / 1510 nm rx , 3.3v / 1.25 gb/s rohs compliant single-fiber transceiver Datasheet

Optoway
BTR-7780-1590G
1
***********************************************************************************************************************************************************************
BTR-7780-1590G / BTR-7780-1590-SPG
1590 nm TX / 1510 nm RX , 3.3V / 1.25 Gb/s RoHS Compliant Single-Fiber Transceiver
**********************************************************************************************************************************************************************
FEATURES
DESCRIPTION
l
l
l
l
l
l
l
l
l
l
l
l
l
l
The BTR-7780-1590G series is high performance module
for single fiber communications by using 1590 nm DFB LD
transmitter and 1510 nm receiver. A guaranteed minimum
optical link budget of 24 dB is offered which can
correspond to a link distance of over 80 km (assuming worst
case fiber loss of 0.25 dB/km). The transmitter section
uses a multiple quantum well laser and is a class 1 laser
compliant according to International Safety Standard
IEC-60825. The receiver section uses an integrated 1510
nm detector preamplifier (IDP) mounted in an optical
header and a limiting post-amplifier IC. A PECL logic
interface simplifies interface to external circuitry.
Single Fiber Bi-Directional Transceiver
1590 nm DFB LD Transmitter
1510 nm Receiver
24 dB Link Power Budget At Least
Link distance up to 80 km
Industry Standard 1 x 9 Footprint
Single +3.3 V Power Supply
RoHS Compliant
0 to 70oC Operating
LVPECL Differential Inputs and Outputs
LVPECL Signal Detect Output: BTR-7780-1590G
LVTTL Signal Detect Output : BTR-7780C-1590G
Wave Solderable and Aqueous Washable
Class 1 Laser International Safety Standard IEC-60825
Compliant
LASER SAFETY
This single mode transceiver is a Class 1 laser product. It
complies with IEC-60825 and FDA 21 CFR 1040.10 and
1040.11. The transceiver must be operated within the
specified temperature and voltage limits. The optical ports
of the module shall be terminated with an optical connector
or with a dust plug.
APPLICATIONS
l WDM 1.25 Gb/s Links
l SONET/SDH Equipment Interconnect
l Fiber Channel 1.063 Gb/s Links
ORDER INFORMATION
P/No.
Bit
Rate
(Gb/s)
Distance
(km)
TX
(nm)
RX
(nm)
Voltage
(V)
Package
Temp
(oC)
TX
Power
(dBm)
RX
Sens.
(dBm)
BTR-7780C-1590G
1.25
80
1590 DFB
1510
3.3
1X9
0 to 70
3 to -2
-26
TTL
Yes
BTR-7780-1590G
1.25
80
1590 DFB
1510
3.3
1X9
0 to 70
3 to -2
-26
PECL
Yes
Signal
Detect
RoHS
Compliant
Note: 1. BTR-XXXXXG is 1X9 SC receptacle type package.
2. BTR-XXXXX-APBBBG is 1X9 pigtail type package with different connector, A=S is SC connector, A=F is FC
connector, A=T is ST connector, A=L is LC connector, A=M is MU connector; BBB is the length of fiber in cm.
Absolute Maximum Ratings
Parameter
Storage Temperature
Operating Temperature
Soldering Temperature
Power Supply Voltage
Input Voltage
Output Current
Symbol
Tstg
Topr
--Vcc
--Iout
Min
-40
0
0
GND
Max
85
70
250
4.5
Vcc
Units
o
C
o
C
o
C
V
V
0
30
mA
Min
3.13
0
Typ
3.3
Max
3.47
70
1300
280
Notes
10 seconds on leads only
Recommended Operating Conditions
Parameter
Power Supply Voltage
Operating Temperature
Data Rate
Power Supply Current
Symbol
Vcc
Topr
1250
Icc
Units
V
o
C
Mb/s
mA
***********************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
10/1/2005 V2.0
Optoway
BTR-7780-1590G
2
***********************************************************************************************************************************************************************
Transmitter Specifications (0 oC < Topr < 70 oC, 3.13V < Vcc < 3.47V)
Parameter
Optical
Optical Transmit Power
Output Center Wavelength
Output Spectrum Width
Side Mode Suppression Ratio
Extinction Ratio
Output Eye
Optical Rise Time
Optical Fall Time
Relative Intensity Noise
Total Jitter
Electrical
Data Input Current – Low
Data Input Current – High
Differential Input Voltage
Data Input Voltage – Low
Data Input Voltage -- High
Symbol
Min
Po
-2
1580
λ
--∆λ
SMSR
30
ER
9.0
Compliant with IEEE 802.3z
tr
tf
RIN
TJ
IIL
IIH
VIH - VIL
VIL - VCC
VIH - VCC
Typ
Max
Units
Notes
---
---
---
dBm
nm
nm
dB
dB
1
---
3
1620
1
0.26
0.26
-116
0.227
ns
ns
dB/Hz
ns
-350
350
300
-2.0
-1.1
-1.58
-0.74
µA
µA
mV
V
V
-20 dB Width
20% to 80% Values
20% to 80% Values
2
3
3
Notes: 1. Output power is power coupled into a 9/125 µm single mode fiber.
2. Measured with a 27-1 PRBS.
3. These inputs are compatible with 10K, 10KH and 100K ECL and LVPECL inputs.
Receiver Specifications (0oC < Topr < 70oC, 3.13 V < Vcc < 3. 47V)
Parameter
Optical
Sensitivity
Maximum Input Power
Signal Detect -- Asserted
Signal Detect -- Deasserted
Signal detect -- Hysteresis
Wavelength of Operation
Optical Return Loss
Electrical
Data Output Voltage – Low
Data Output Voltage – High
SD Output Voltage -- Low
SD Output Voltage -- High
SD Output Voltage -- Low
SD Output Voltage -- High
Symbol
Min
Typ
Max
Units
Notes
--Pin
Pa
Pd
-----------
-26
---26
---
dBm
dBm
dBm
dBm
dB
nm
dB
1
ORL
---3
---40
1.0
1480
14
V OL - VCC
V OH - VCC
V OL - VCC
V OH - VCC
VOL
VOH
-2.0
-1.1
-2.0
-1.1
0
2.0
1520
-1.58
-0.74
-1.58
-0.74
0.8
Vcc+0.3
V
V
V
V
V
V
Transition: low to high
Transition: high to low
2
3
3
BTR-7780-1590G
BTR-7780C-1590G
Notes: 1. Minimum sensitivity and saturation levels at BER=1E-12 for a 2 7-1 PRBS.
2. At least 30 dB optical isolation for the wavelength 1580 to 1620 nm.
3. These outputs are compatible with 10K, 10KH and 100K ECL and LVPECL outputs.
***************************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
10/1/2005 V2.0
Optoway
BTR-7780-1590G
3
***********************************************************************************************************************************************************************
CONNECTION DIAGRAM
Receiver Signal Ground
Receiver Data Out
Receiver Data Out Bar
Signal Detect
Receiver Power Supply
Transmitter Power Supply
Transmitter Data In Bar
Transmitter Data In
Transmitter Signal Ground
PIN
1
2
3
4
5
6
7
8
9
Symbol
Rx GND
RD+
RD−
SD
Rx Vcc
Tx Vcc
TD−
TD+
Tx GND
1 (Rx GND)
2 (RD+)
3 (RD−)
4 (SD)
5 (Rx Vcc)
6 (Tx Vcc)
7 (TD−)
8 (TD+)
9 (Tx GND)
N/C
TOP VIEW
N/C
Notes
Directly connect this pin to the receiver ground plane
See recommended circuit schematic
See recommended circuit schematic
Active high on this indicates a received optical signal
+3.3V dc power for the receiver section
+3.3V dc power for the transmitter section
See recommended circuit schematic
See recommended circuit schematic
Directly connect this plan to the trransmitter ground plane
RECOMMENDED CIRCUIT SCHEMATIC
Vcc3.3V
Vcc3.3V
Vcc3.3V
R2
NA
R3
NA
R1
NA
R4
NA
C9
MICROSTRIP5
100nF
C10
Z=50R
MICROSTRIP6
100nF
Z=5OR
TDLVPECL
TD+
L2
Vcc3.3V
1uH
U2
9
8
7
6
5
4
3
2
1
TXGND
TD+
TDTXVCC
RXVCC
SD
RDRD+
RXGND
BTR-77XX(C)/76XX(C)
C2
C3
100nF
100nF
C4
10uF
L1
PHY DEVICE
1uH
C1
C8
100nF
10uF
Vcc3.3V
RD+
R21
1K
C12
MICROSTRIP7
100nF
Z=50R
MICROSTRIP8
R14
100R
LVPECL
RD-
C11 100nF Z=5OR
SD / LVPECL
The split-load terminations for ECL signals need to be located at the input of devices receiving those ECL signals. The power
supply filtering is required for good EMI performance. Use short tracks from the inductor L1/L2 to the module Rx Vcc and Tx
Vcc. A GND plane under the module is required for good EMI and sensitivity performance.
***************************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
10/1/2005 V2.0
Optoway
BTR-7780-1590G
4
***********************************************************************************************************************************************************************
PACKAGE DIAGRAM
Units in mm
1) Pigtail Type
BTR-7780-1590-SP50G
Note: Length L is 50± 3 cm. Other pigtail’s length is available upon request.
2) Receptacle Type
BTR-7780-1590G
Note: Specifications subject to change without notice.
***************************************************************************************************************************************************************************
OPTOWAY TECHNOLOGY INC. No.38, Kuang Fu S. Road, Hu Kou, Hsin Chu Industrial Park, Hsin Chu, Taiwan 303
Tel: 886-3-5979798
Fax: 886-3-5979737
E-mail: [email protected] http: // www.optoway.com.tw
10/1/2005 V2.0
Similar pages