ETC2 MKT367 Metallized polyester film capacitor Datasheet

BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
MKT RADIAL EPOXY LACQUERED TYPE
PITCH 5 mm (kinked, straight and bent back leads)
PITCH 7.5 mm (kinked and straight leads)
handbook, full pagewidth
365
366
367
CBA774
Fig.1 Simplified outlines.
FEATURES
• Low-inductive wound cell of
metallized (PETP) film
• Cell protected by epoxy lacquer
• Radial leads of solder-coated wire
• Resistant to solvents and rinsing
liquids.
APPLICATIONS
• Blocking and coupling
• Bypass and energy reservoir.
QUICK REFERENCE DATA
DESCRIPTION
Capacitance range (E12 series)
0.01 to 1.0 µF
Capacitance tolerance
±10%; ±5%
Rated (DC) voltage
63 V; 100 V; 250 V; 400 V
Rated (AC) voltage
40 V; 63 V; 160 V; 220 V
Climatic category
55/100/56
Rated temperature
85 °C
Maximum application temperature
100 °C
Tangent of loss angle at 10 kHz
100 × 10−4
Reference specification
IEC 60384-2
Performance grade
grade 1 (long life)
DETAIL SPECIFICATION
For more detailed data and test
requirements see “Type detail
specification HQN-384-02/105”.
1999 Apr 29
VALUE
79
BC Components
Product specification
Metallized polyester film capacitors
MKT 365
COMPOSITION OF CATALOGUE NUMBER
TYPE AND PITCHES
365
MULTIPLIER
(nF)
5.0 mm
CAPACITANCE
(numerically)
0.1
2
1
3
10
4
100
5
Example:
104 = 10 × 10 = 100 nF
2222
TYPE
PACKAGING
ammopack
365
taped on reel
1999 Apr 29
365 XX XX X
LEAD CONFIGURATION
C-TOL
63 V
100 V
250 V
400 V
kinked leads;
H = 16.0 mm; P0 = 12.7 mm
±10%
75
85
−
−
±5%
76
86
−
−
bent back kinked leads;
H = 16.0 mm; P0 = 12.7 mm
±10%
15
25
45
55
±5%
16
26
46
56
kinked leads;
H = 16.0 mm; P0 = 12.7 mm
±10%
71
81
−
−
±5%
72
82
−
−
bent back kinked leads;
H = 16.0 mm; P0 = 12.7 mm
±10%
11
21
41
51
±5%
12
22
42
52
80
BC Components
Product specification
Metallized polyester film capacitors
MKT 366/367
TYPE AND PITCHES
366
367
MULTIPLIER
(nF)
5.0 mm
7.5 mm
0.1
2
CAPACITANCE
1
3
(numerically)
10
4
100
5
Example:
104 = 10 × 10 = 100 nF
2222
TYPE
PACKAGING
36.
XX XX X
LEAD CONFIGURATION
C-TOL
63 V
100 V
250 V
400 V
±10%
75
85
−
−
±5%
76
86
−
−
kinked;
lead length 17.0 mm
±10%
71
81
−
−
±5%
72
82
−
−
straight;
lead length 4.0 mm
±10%
75
85
−
−
±5%
76
86
−
−
±10%
71
81
−
−
±5%
72
82
−
−
63 V
100 V
250 V
400 V
25
45
55
kinked;
lead length 4.0 mm
366
367
loose in box
loose in box
straight;
lead length 22.0 mm
Available on request with pitch = 7.5 mm
366
367
1999 Apr 29
kinked;
lead length 4.0 mm
±10%
15
±5%
16
26
46
56
kinked;
lead length 17.0 mm
±10%
11
21
41
51
±5%
12
22
42
52
straight;
lead length 4.0 mm
±10%
15
25
45
55
±5%
16
26
46
56
straight;
lead length 22.0 mm
±10%
11
21
41
51
±5%
12
22
42
52
loose in box
loose in box
81
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
MKT 365/366/367 GENERAL DATA
l
PITCH 5 mm (kinked and straight leads)
b
l
b
≤1.5
handbook, full pagewidth
h
seating plane(1)
(2)
∅1.3
h
α
lt
lt
P
P
A
CBA775
∅dt
∅dt
(1) Hole ∅1.0 for dt = 0.5 mm.
(2) 0 ≤ α < 50°.
Fig.4 Outline.
Specific reference data for the 63 V DC capacitors
VALUE
DESCRIPTION
Tangent of loss angle:
C ≤ 0.1 µF
0.1 µF < C ≤ 0.47 µF
0.47 µF < C ≤ 1.0 µF
Rated voltage pulse slope (dU/dt)R at 63 V (DC)
R between leads, for C ≤ 0.33 µF at 10 V; 1 minute
RC between leads, for C > 0.33 µF at 100 V; 1 minute
R between interconnecting leads and casing; 100 V; 1 minute
Withstanding voltage DC (cut off current 10 mA);
rise time 100 V/s
at 1 kHz
at 10 kHz
at 100 kHz
≤75 × 10−4
≤75 × 10−4
≤75 × 10−4
≤130 × 10−4
≤130 × 10−4
≤130 × 10−4
110 V/µs
>15000 MΩ
>5000 s
>30000 MΩ
100 V; 1 minute
≤225 × 10−4
≤300 × 10−4
−
Available 63 V DC versions
PACKAGING(1)
Ammopack
Taped on reel
Loose in box
Loose in box
DIMENSIONS
LEAD
PITCH
CONFIGURATION (mm)
5
5
5
5
5
5
H = 16.0 mm; note 2
lt = 4.0 +1.0/−0.5 mm
lt = 17.0 ±4.0 mm
lt = 4.0 +1.0/−0.5 mm
lt = 22.0 ±4.0 mm
kinked
straight
FIRST 9 DIGITS OF
CATALOGUE NUMBER
C-tol = ±10%
C-tol = ±5%
2222 365 75...
2222 365 71...
2222 366 75...
2222 366 71...
2222 367 75...
2222 367 71...
2222 365 76...
2222 365 72...
2222 366 76...
2222 366 72...
2222 367 76...
2222 367 72...
Notes
1. For SPQ refer to this handbook, chapter “Packaging information”.
2. H = in-tape height; for detailed specifications refer to this handbook, chapter “Packaging information”.
1999 Apr 29
82
ORDERING
preferred
on request
on request
on request
on request
on request
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
URdc = 63 V; URac = 40 V
Pitch 5 mm (kinked and straight leads)
CATALOGUE NUMBER
C
(µF)
DIMENSIONS(1)
bmax × hmax × lmax
(mm)
AMMOPACK; H = 16.0 mm
MASS
(g)
C-tol = ±10%
catalogue
number(2)
C-tol = ±5%
last 5 digits(2)
Pitch = 5.0 +0.4/−0.2 mm; dt = 0.50 ±0.05 mm; A = 1.7 ±0.3 mm
0.047
2222 365 75473
.. 76473
0.056
2222 365 75563
.. 76563
0.068
2222 365 75683
.. 76683
2222 365 75823
.. 76823
0.082
4.0 × 12.5 (7.5) × 7.3
0.3
0.1
2222 365 75104
.. 76104
0.12
2222 365 75124
.. 76124
2222 365 75154
.. 76154
0.15
4.0 × 13.0 (8.0) × 7.3
0.3
0.18
4.0 × 13.5 (8.5) × 7.3
0.4
2222 365 75184
.. 76184
0.22
4.2 × 13.5 (8.5) × 7.3
0.4
2222 365 75224
.. 76224
0.27
4.5 × 14.0 (9.0) × 7.3
0.4
2222 365 75274
.. 76274
0.33
4.5 × 14.5 (10.5) × 7.3
0.4
2222 365 75334
.. 76334
2222 365 75394
.. 76394
0.47
4.5 × 15.5 (11.5) × 7.3
0.4
2222 365 75474
.. 76474
0.56
5.0 × 14.0 (10.0) × 7.3
0.4
2222 365 75564
.. 76564
0.68
5.5 × 14.5 (10.5) × 7.3
0.4
2222 365 75684
.. 76684
0.82
5.5 × 15.0 (11.0) × 7.3
0.5
2222 365 75824
.. 76824
1.0
5.5 × 15.5 (11.5) × 7.3
0.5
2222 365 75105
.. 76105
0.39
Notes
1. Dimensions in brackets for straight leads.
2. The shading indicates preferred types.
1999 Apr 29
83
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
MKT 365/366/367 GENERAL DATA
PITCH 5 mm (bent back leads)
PITCH 7.5 mm (kinked and straight leads)
l
l
b
l
b
≤1.5
handbook, full pagewidth
seating
plane(1)
h
h
α
α
(2)
(2)
lt
P
h
∅1.3
A
lt
P
lt
∅dt
A
∅dt
P
CBA948
(1) Hole ∅1.0 for dt = 0.6 mm.
(2) 0 ≤ α < 50°.
Fig.5 Outline.
Specific reference data for the 63 V DC capacitors
VALUE
DESCRIPTION
Tangent of loss angle:
C ≤ 0.1 µF
0.1 µF < C ≤ 0.47 µF
0.47 µF < C ≤ 1.0 µF
Rated voltage pulse slope (dU/dt)R at 63 V (DC)
R between leads, for C ≤ 0.33 µF at 10 V; 1 minute
RC between leads, for C > 0.33 µF at 100 V; 1 minute
R between interconnecting leads and casing; 100 V; 1 minute
Withstanding (DC) voltage (cut off current 10 mA);
rise time 100 V/s
at 1 kHz
at 10 kHz
at 100 kHz
≤75 × 10−4
≤75 × 10−4
≤75 × 10−4
≤130 × 10−4
≤130 × 10−4
≤130 × 10−4
110 V/µs
>15000 MΩ
>5000 s
>30000 MΩ
100 V; 1 minute
≤225 × 10−4
≤300 × 10−4
−
Available 63 V DC versions
PACKAGING(1)
Ammopack
Taped on reel
Loose in box
Loose in box
DIMENSIONS
H = 16.0 mm; note 2
lt = 4.0 +1.0/−0.5 mm
lt = 17.0 ±4.0 mm
lt = 4.0 +1.0/−0.5 mm
lt = 22.0 ±4.0 mm
LEAD
PITCH
CONFIGURATION (mm)
5
5
7.5
7.5
7.5
7.5
bent back
kinked
straight
FIRST 9 DIGITS OF
CATALOGUE NUMBER
C-tol = ±10%
2222 365 15...
2222 365 11...
2222 366 15...
2222 366 11...
2222 367 15...
2222 367 11...
C-tol = ±5%
2222 365 16...
2222 365 12...
2222 366 16...
2222 366 12...
2222 367 16...
2222 367 12...
Notes
1. For SPQ refer to this handbook, chapter “Packaging information”.
2. H = in-tape height; for detailed specifications refer to this handbook, chapter “Packaging information”.
1999 Apr 29
84
ORDERING
preferred
on request
on request
on request
on request
on request
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
URdc = 63 V; URac = 40 V
Pitch 5 mm (bent back leads)
PACKAGING
C
(µF)
DIMENSIONS
bmax × hmax × lmax
(mm)
AMMOPACK; H = 16.0 mm
MASS
(g)
C-tol = ±10%
catalogue
number(1)
C-tol = ±5%
last 5 digits(1)
Pitch = 5.0 +0.4/−0.2 mm; dt = 0.60 ±0.06 mm; A = 1.7 ±0.3 mm(2)
0.12
0.15
0.18
4.0 × 13.5 × 10.0
0.4
0.22
0.27
4.5 × 14.0 × 10.0
0.5
0.33
5.0 × 14.5 × 10.0
0.6
0.39
0.47
0.56
2222 365 15124
.. 16124
2222 365 15154
.. 16154
2222 365 15184
.. 16184
2222 365 15224
.. 16224
2222 365 15274
.. 16274
2222 365 15334
.. 16334
2222 365 15394
.. 16394
2222 365 15474
.. 16474
2222 365 15564
.. 16564
2222 365 15684
.. 16684
0.82
2222 365 15824
.. 16824
1.0
2222 365 15105
.. 16105
0.68
5.5 × 15.0 × 10.0
0.7
Notes
1. The shading indicates preferred types.
2. Pitch = 7.5 mm (kinked and straight leads) is available on request; for dimensions and package quantities see
“Type detail specification HQN-384-02/105”.
1999 Apr 29
85
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
MKT 365/366/367 GENERAL DATA
l
PITCH 5 mm (kinked and straight leads)
b
l
b
≤1.5
handbook, full pagewidth
h
seating plane(1)
(2)
∅1.3
h
α
lt
lt
P
P
A
CBA775
∅dt
∅dt
(1) Hole ∅1.0 for dt = 0.5 mm.
(2) 0 ≤ α < 50°.
Fig.6 Outline.
Specific reference data for the 100 V DC capacitors
VALUE
DESCRIPTION
Tangent of loss angle:
C ≤ 0.1 µF
0.1 µF < C ≤ 0.47 µF
Rated voltage pulse slope (dU/dt)R at 100 V (DC)
R between leads, for C ≤ 0.33 µF at 100 V; 1 minute
RC between leads, for C > 0.33 µF at 100 V; 1 minute
R between interconnecting leads and casing; 100 V; 1 minute
Withstanding (DC) voltage (cut off current 10 mA);
rise time 100 V/s
at 1 kHz
at 10 kHz
at 100 kHz
≤75 × 10−4
≤75 × 10−4
≤130 × 10−4
≤130 × 10−4
110 V/µs
>15000 MΩ
>5000 s
>30000 MΩ
160 V; 1 minute
≤225 × 10−4
≤225 × 10−4
Available 100 V DC versions
PACKAGING(1)
Ammopack
Taped on reel
Loose in box
Loose in box
DIMENSIONS
LEAD
PITCH
CONFIGURATION (mm)
5
5
5
5
5
5
H = 16.0 mm; note 2
lt = 4.0 +1.0/−0.5 mm
lt = 17.0 ±4.0 mm
lt = 4.0 +1.0/−0.5 mm
lt = 22.0 ±4.0 mm
kinked
straight
FIRST 9 DIGITS OF
CATALOGUE NUMBER
C-tol = ±10%
C-tol = ±5%
2222 365 85...
2222 365 81...
2222 366 85...
2222 366 81...
2222 367 85...
2222 367 81...
2222 365 86...
2222 365 82...
2222 366 86...
2222 366 82...
2222 367 86...
2222 367 82...
Notes
1. For SPQ refer to this handbook, chapter “Packaging information”.
2. H = in-tape height; for detailed specifications refer to this handbook, chapter “Packaging information”.
1999 Apr 29
86
ORDERING
preferred
on request
on request
on request
on request
on request
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
URdc = 100 V; URac = 63 V
Pitch 5 mm (kinked and straight leads)
CATALOGUE NUMBER
C
(µF)
DIMENSIONS(1)
bmax × hmax × lmax
(mm)
AMMOPACK; H = 16.0 mm
MASS
(g)
C-tol = ±10%
catalogue
number(2)
C-tol = ±5%
last 5 digits(2)
Pitch = 5.0 +0.4/−0.2 mm; dt = 0.50 ±0.05 mm; A = 1.7 ±0.3 mm
0.01
2222 365 85103
.. 86103
0.012
2222 365 85123
.. 86123
0.015
2222 365 85153
.. 86153
2222 365 85183
.. 86183
0.018
0.022
3.7 × 12.5 (7.5) × 7.3
0.3
2222 365 85223
.. 86223
0.027
2222 365 85273
.. 86273
0.033
2222 365 85333
.. 86333
0.039
2222 365 85393
.. 86393
0.047
2222 365 85473
.. 86473
2222 365 85563
.. 86563
2222 365 85683
.. 86683
0.056
4.0 × 12.5 (7.5) × 7.3
0.3
0.068
0.082
4.0 × 13.0 (8.0) × 7.3
0.3
0.1
0.12
0.15
4.0 × 13.5 (8.5) × 7.3
0.4
0.18
2222 365 85823
.. 86823
2222 365 85104
.. 86104
2222 365 85124
.. 86124
2222 365 85154
.. 86154
2222 365 85184
.. 86184
0.22
4.2 × 13.5 (8.5) × 7.3
0.4
2222 365 85224
.. 86224
0.27
4.5 × 14.0 (9.0) × 7.3
0.4
2222 365 85274
.. 86274
Notes
1. Dimensions in brackets for straight leads.
2. The shading indicates preferred types.
1999 Apr 29
87
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
MKT 365/366/367 GENERAL DATA
PITCH 5 mm (bent back leads)
PITCH 7.5 mm (kinked and straight leads)
l
l
b
l
b
≤1.5
handbook, full pagewidth
seating
plane(1)
h
h
α
α
(2)
(2)
lt
P
h
∅1.3
A
lt
P
lt
∅dt
A
∅dt
P
CBA948
(1) Hole ∅1.0 for dt = 0.6 mm.
(2) 0 ≤ α < 50°.
Fig.7 Outline.
Specific reference data for the 100 V DC capacitors
VALUE
DESCRIPTION
Tangent of loss angle:
C ≤ 0.1 µF
0.1 µF < C ≤ 0.47 µF
Rated voltage pulse slope (dU/dt)R at 100 V (DC)
R between leads, for C ≤ 0.33 µF at 100 V; 1 minute
RC between leads, for C > 0.33 µF at 100 V; 1 minute
R between interconnecting leads and casing; 100 V; 1 minute
Withstanding (DC) voltage (cut off current 10 mA);
rise time 100 V/s
at 1 kHz
at 10 kHz
at 100 kHz
≤75 × 10−4
≤75 × 10−4
≤130 × 10−4
≤130 × 10−4
110 V/µs
>15000 MΩ
>5000 s
>30000 MΩ
160 V; 1 minute
≤225 × 10−4
≤225 × 10−4
Available 100 V DC versions
PACKAGING(1)
Ammopack
Taped on reel
Loose in box
Loose in box
DIMENSIONS
H = 16.0 mm; note 2
lt = 4.0 +1.0/−0.5 mm
lt = 17.0 ±4.0 mm
lt = 4.0 +1.0/−0.5 mm
lt = 22.0 ±4.0 mm
LEAD
PITCH
CONFIGURATION (mm)
5
5
7.5
7.5
7.5
7.5
bent back
kinked
straight
FIRST 9 DIGITS OF
CATALOGUE NUMBER
C-tol = ±10%
C-tol = ±5%
2222 365 25...
2222 365 21...
2222 366 25...
2222 366 21...
2222 367 25...
2222 367 21...
2222 365 26...
2222 365 22...
2222 366 26...
2222 366 22...
2222 367 26...
2222 367 22...
Notes
1. For SPQ refer to this handbook, chapter “Packaging information”.
2. H = in-tape height; for detailed specifications refer to this handbook, chapter “Packaging information”.
1999 Apr 29
88
ORDERING
preferred
on request
on request
on request
on request
on request
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
URdc = 100 V; URac = 63 V
Pitch 5 mm (bent back leads)
CATALOGUE NUMBER
C
(µF)
DIMENSIONS
bmax × hmax × lmax
(mm)
AMMOPACK; H = 16.0 mm
MASS
(g)
C-tol = ±10%
catalogue
number(1)
C-tol = ±5%
last 5 digits(1)
Pitch = 5.0 +0.4/−0.2 mm; dt = 0.60 ±0.06 mm; A = 1.7 ±0.3 mm(2)
0.039
2222 365 25393
.. 26393
0.047
2222 365 25473
.. 26473
2222 365 25563
.. 26563
2222 365 25683
.. 26683
2222 365 25823
.. 26823
0.056
0.068
4.0 × 13.5 × 10.0
0.4
0.082
0.1
0.12
4.5 × 14.0 × 10.5
0.5
0.15
5.0 × 14.5 × 10.5
0.6
5.5 × 15.0 × 10.5
0.7
0.18
0.22
0.27
0.33
0.39
6.0 × 15.5 × 10.5
0.7
0.47
2222 365 25104
.. 26104
2222 365 25124
.. 26124
2222 365 25154
.. 26154
2222 365 25184
.. 26184
2222 365 25224
.. 26224
2222 365 25274
.. 26274
2222 365 25334
.. 26334
2222 365 25394
.. 26394
2222 365 25474
.. 26474
Notes
1. The shading indicates preferred types.
2. Pitch = 7.5 mm (kinked and straight leads) is available on request; for dimensions and package quantities see
“Type detail specification HQN-384-02/105”.
1999 Apr 29
89
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
MKT 365/366/367 GENERAL DATA
PITCH 5 mm (bent back leads)
PITCH 7.5 mm (kinked and straight leads)
l
l
b
l
b
≤1.5
handbook, full pagewidth
seating
plane(1)
h
h
α
α
(2)
(2)
lt
P
h
∅1.3
A
lt
P
lt
∅dt
A
∅dt
P
CBA948
(1) Hole ∅1.0 for dt = 0.6 mm.
(2) 0 ≤ α < 50°.
Fig.8 Outline.
Specific reference data for the 250 V DC capacitors
VALUE
DESCRIPTION
Tangent of loss angle:
C ≤ 0.1 µF
0.1 µF < C ≤ 0.15 µF
Rated voltage pulse slope (dU/dt)R at 250 V (DC)
R between leads, for C ≤ 0.33 µF at 100 V; 1 minute
R between interconnected leads and casing; 100 V; 1 minute
Withstanding (DC) voltage (cut off current 10 mA);
rise time 100 V/s
at 1 kHz
at 10 kHz
at 100 kHz
≤75 × 10−4
≤75 × 10−4
≤130 × 10−4
≤120 × 10−4
70 V/µs
>30000 MΩ
>30000 MΩ
400 V; 1 minute
≤225 × 10−4
≤225 × 10−4
Available 250 V DC versions
PACKAGING(1)
Ammopack
Taped on reel
Loose in box
Loose in box
DIMENSIONS
H = 16.0 mm; note 2
lt = 4.0 +1.0/−0.5 mm
lt = 17.0 ±4.0 mm
lt = 4.0 +1.0/−0.5 mm
lt = 22.0 ±4.0 mm
LEAD
PITCH
CONFIGURATION (mm)
5
5
7.5
7.5
7.5
7.5
bent back
kinked
straight
FIRST 9 DIGITS OF
CATALOGUE NUMBER
C-tol = ±10%
C-tol = ±5%
2222 365 45...
2222 365 41...
2222 366 45...
2222 366 41...
2222 367 45...
2222 367 41...
2222 365 46...
2222 365 42...
2222 366 46...
2222 366 42...
2222 367 46...
2222 367 42...
Notes
1. For SPQ refer to this handbook, chapter “Packaging information”.
2. H = in-tape height; for detailed specifications refer to this handbook, chapter “Packaging information”.
1999 Apr 29
90
ORDERING
preferred
on request
on request
on request
on request
on request
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
URdc = 250 V; URac = 160 V
Pitch 5 mm (bent back leads)
CATALOGUE NUMBER
C
(µF)
DIMENSIONS
bmax × hmax × lmax
(mm)
AMMOPACK; H = 16.0 mm
MASS
(g)
C-tol = ±10%
catalogue
number(1)
C-tol = ±5%
last 5 digits(1)
Pitch = 5.0 +0.4/−0.2 mm; dt = 0.60 ±0.06 mm; A = 1.7 ±0.3 mm(2)
0.018
2222 365 45183
.. 46183
0.022
2222 365 45223
.. 46223
2222 365 45273
.. 46273
2222 365 45333
.. 46333
2222 365 45393
.. 46393
0.027
0.033
4.0 × 13.5 × 10.0
0.4
0.039
0.047
2222 365 45473
.. 46473
0.056
2222 365 45563
.. 46563
2222 365 45683
.. 46683
0.068
4.5 × 13.0 × 10.0
0.5
2222 365 45823
.. 46823
0.1
5.0 × 13.5 × 10.0
0.6
2222 365 45104
.. 46104
0.12
5.5 × 14.0 × 10.0
0.6
2222 365 45124
.. 46124
0.15
5.5 × 15.5 × 10.0
0.7
2222 365 45154
.. 46154
0.082
Notes
1. The shading indicates preferred types.
2. Pitch = 7.5 mm (kinked and straight leads) is available on request; for dimensions and package quantities see
“Type detail specification HQN-384-02/105”.
1999 Apr 29
91
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
MKT 365/366/367 GENERAL DATA
PITCH 5 mm (bent back leads)
PITCH 7.5 mm (kinked and straight leads)
l
l
b
l
b
≤1.5
handbook, full pagewidth
seating
plane(1)
h
h
α
α
(2)
(2)
lt
P
h
∅1.3
A
lt
P
lt
∅dt
A
∅dt
P
CBA948
(1) Hole ∅1.0 for dt = 0.6 mm.
(2) 0 ≤ α < 50°.
Fig.9 Outline.
Specific reference data for the 400 V DC capacitors
VALUE
DESCRIPTION
Tangent of loss angle:
C ≤ 0.056 µF
C ≤ 0.1 µF
Rated voltage pulse slope (dU/dt)R at 400 V (DC)
R between leads, for C ≤ 0.33 µF at 100 V; 1 minute
R between interconnected leads and casing; 100 V; 1 minute
Withstanding (DC) voltage (cut off current 10 mA);
rise time 100 V/s
at 1 kHz
at 10 kHz
at 100 kHz
≤75 × 10−4
≤75 × 10−4
≤120 × 10−4
≤130 × 10−4
110 V/µs
>30000 MΩ
>30000 MΩ
640 V; 1 minute
≤200 × 10−4
≤225 × 10−4
Available 400 V DC versions
PACKAGING(1)
Ammopack
Taped on reel
Loose in box
Loose in box
DIMENSIONS
H = 16.0 mm; note 2
lt = 4.0 +1.0/−0.5 mm
lt = 17.0 ±4.0 mm
lt = 4.0 +1.0/−0.5 mm
lt = 22.0 ±4.0 mm
LEAD
PITCH
CONFIGURATION (mm)
5
5
7.5
7.5
7.5
7.5
bent back
kinked
straight
FIRST 9 DIGITS OF
CATALOGUE NUMBER
C-tol = ±10%
C-tol = ±5%
2222 365 55...
2222 365 51...
2222 366 55...
2222 366 51...
2222 367 55...
2222 367 51...
2222 365 56...
2222 365 52...
2222 366 56...
2222 366 52...
2222 367 56...
2222 367 52...
Notes
1. For SPQ refer to this handbook, chapter “Packaging information”.
2. H = in-tape height; for detailed specifications refer to this handbook, chapter “Packaging information”.
1999 Apr 29
92
ORDERING
preferred
on request
on request
on request
on request
on request
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
URdc = 400 V; URac = 220 V
Pitch 5 mm (bent back leads)
CATALOGUE NUMBER
C
(µF)
DIMENSIONS
bmax × hmax × lmax
(mm)
AMMOPACK; H = 16.0 mm
MASS
(g)
C-tol = ±10%
catalogue
number(1)
C-tol = ±5%
last 5 digits(1)
Pitch = 5.0 +0.4/−0.2 mm; dt = 0.60 ±0.06 mm; A = 1.7 ±0.3 mm(2)
0.0033
2222 365 55332
.. 56332
0.0039
2222 365 55392
.. 56392
0.0047
2222 365 55472
.. 56472
0.0056
2222 365 55562
.. 56562
2222 365 55682
.. 56682
0.0068
4.0 × 13.5 × 10.0
0.4
0.0082
2222 365 55822
.. 56822
0.01
2222 365 55103
.. 56103
0.012
2222 365 55123
.. 56123
0.015
2222 365 55153
.. 56153
0.018
4.5 × 13.0 × 10.0
0.6
2222 365 55183
.. 56183
0.022
5.0 × 13.5 × 10.0
0.7
2222 365 55223
.. 56223
0.027
4.0 × 12.5 × 10.0
0.4
2222 365 55273
.. 56273
0.033
4.5 × 13.0 × 10.0
0.5
2222 365 55333
.. 56333
0.039
5.0 × 13.5 × 10.0
0.5
2222 365 55393
.. 56393
0.047
5.0 × 13.5 × 10.0
0.6
2222 365 55473
.. 56473
0.056
5.5 × 14.0 × 10.0
0.7
2222 365 55563
.. 56563
Notes
1. The shading indicates preferred types.
2. Pitch = 7.5 mm (kinked and straight leads) is available on request; for dimensions and package quantities see
“Type detail specification HQN-384-02/105”.
1999 Apr 29
93
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
CONSTRUCTION
Mounting
Description
NORMAL USE
• Low-inductive wound cell of metallized polyethylene
terephthalate film
The capacitors are designed for mounting on
printed-circuit boards. The capacitors packed in bandoliers
are designed for mounting on printed-circuit boards by
means of automatic insertion machines.
For detailed tape specifications refer to this handbook,
chapter “Packaging information”.
• Protected by a hard, water repellent, solvent resistant
epoxy lacquer
• Radial leads, solder coated:
– Copper clad steel wire for pitch = 5 mm (kinked and
straight leads)
SPECIFIED METHOD OF MOUNTING TO WITHSTAND VIBRATION
– Copper wire for pitch = 5 mm (bent back leads) and
pitch = 7.5 mm (kinked and straight leads).
AND SHOCK
In order to withstand vibration and shock tests, it must be
ensured that the underside of the kinks are in good contact
with the printed-circuit board:
• For pitches ≤15 mm the capacitors shall be
mechanically fixed by the leads.
metallized polyester film
• For larger pitches the capacitors shall be mounted in the
same way and the body clamped.
handbook, halfpage
Storage temperature
• Storage temperature: Tstg = −25 to +40 °C with RH
maximum 80% without condensation.
RATINGS AND CHARACTERISTICS REFERENCE
CONDITIONS
metal spray layer
Unless otherwise specified all electrical values apply at an
ambient free air temperature of 23 ±1 °C, an atmospheric
pressure of 86 to 106 kPa and a relative humidity of
50 ±2%.
connecting wire
CBA073
For reference testing, a conditioning period shall be
applied over 96 ±4 hours by heating the products in a
circulating air oven at the rated temperature and a relative
humidity not exceeding 20%.
Fig.10 Construction.
1999 Apr 29
94
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
CHARACTERISTICS
Capacitance
CBA074
2
handbook, full pagewidth
∆C
C
(%)
1
0
−1
−2
−3
102
103
104
f (Hz)
105
Fig.11 Capacitance change as a function of frequency: typical curve.
CBA919
6
handbook, full pagewidth
∆C
C
(%)
4
2
0
−2
max.
typical
−4
min.
−6
−60
−20
20
60
Tamb (°C)
Fig.12 Capacitance change at 1 kHz as a function of ambient free air temperature.
1999 Apr 29
95
100
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
Impedance
CBA076
102
handbook, full pagewidth
MKT 365
Impedance
(Ω)
10
63V
; 10
63V
;1µ
F
0n
F
1
10−1
10−2
10−3
104
105
106
107
108
f (Hz)
Fig.13 Impedance as a function of frequency: typical curves.
Maximum DC and AC voltage as a function of temperature
CBA086
1.2
handbook, full pagewidth
factor
1.0
0.8
0.6
0.4
0.2
0
−60
−40
−20
0
20
40
60
80
100
Tamb (°C)
Fig.14 Multiplying factor for DC and AC voltage as a function of temperature.
1999 Apr 29
96
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
Maximum RMS voltage (sinewave) as a function of frequency
CBA077
102
handbook, full pagewidth
MKT 365/366/367
AC voltage
(V)
10
47
nF
10
0n
F
47
0
10 nF
00
nF
1
10
102
103
104
f (Hz)
105
Fig.15 AC voltage (RS value) as a function of frequency at Tamb ≤ 85 °C for Rdc = 63 V.
CBA776
102
handbook, full pagewidth
MKT 365/366/367
AC voltage
(V)
10
47
10
nF
0n
F
47
0
10 nF
00
nF
1
10
102
103
104
f (Hz)
105
Fig.16 AC voltage (RMS value) as a function of frequency at 85 °C < Tamb ≤ 100 °C for URdc = 63 V.
1999 Apr 29
97
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
CBA078
102
handbook, full pagewidth
MKT 365/366/367
AC voltage
(V)
10
10
47
nF
nF
10
0n
F
47
0n
F
1
10
102
103
104
105
f (Hz)
Fig.17 AC voltage (RMS value) as a function of frequency at Tamb ≤ 85 °C, for URdc = 100 V.
CBA777
102
handbook, full pagewidth
MKT 365/366/367
AC voltage
(V)
10
10
nF
47
1
10
nF
10
0
47 nF
0n
F
102
103
104
f (Hz)
105
Fig.18 AC voltage (RMS value) as a function of frequency at 85 °C < Tamb ≤ 100 °C for URdc = 100 V.
1999 Apr 29
98
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
CBA079
103
handbook, full pagewidth
MKT 365/366/367
AC voltage
(V)
102
18
nF
47
10
1
10
102
103
104
nF
105
f (Hz)
Fig.19 AC voltage (RMS value) as a function of frequency at Tamb ≤ 85 °C, for URdc = 250 V.
CBA778
103
handbook, full pagewidth
MKT 365/366/367
AC voltage
(V)
102
10
18
47
1
10
102
103
104
f (Hz)
nF
nF
105
Fig.20 AC voltage (RMS value) as a function of frequency at 85 °C < Tamb ≤ 100 °C for URdc = 250 V.
1999 Apr 29
99
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
CBA080
103
handbook, full pagewidth
MKT 365/366/367
AC voltage
(V)
102
3.3
15
nF
nF
10
1
10
102
103
104
105
f (Hz)
Fig.21 AC voltage (RMS value) as a function of frequency at Tamb ≤ 85 °C, for URdc = 400 V.
CBA779
103
handbook, full pagewidth
MKT 365/366/367
AC voltage
(V)
102
3.3
10
15
1
10
102
103
104
f (Hz)
nF
nF
105
Fig.22 AC voltage (RMS value) as a function of frequency at 85 °C < Tamb ≤ 100 °C for URdc = 400 V.
Maximum RMS current (sinewave) as a function of frequency
The maximum RMS current is defined by I ac = ω × C × U ac .
Uac is the maximum AC voltage depending on the ambient temperature in Figs 15 to 22.
1999 Apr 29
100
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
Tangent of loss angle
CBA087
103
handbook, full pagewidth
dissipation
factor
(× 10−4)
102
10
102
103
104
f (Hz)
105
Fig.23 Tangent of loss angle as a function of frequency: typical curve.
Insulation resistance
CBA088
105
RC
(s)
104
103
102
−50
0
50
Tamb (°C)
Fig.24 RC product as a function of ambient free air temperature: typical curve.
1999 Apr 29
101
100
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
Maximum allowed component temperature rise (∆T) as a function of the ambient temperature (Tamb)
CBA821
20
handbook, full pagewidth
∆T
(°C)
15
10
5
0
−60
−40
−20
0
20
40
80
60
100
Tamb (°C)
Fig.25 Maximum allowed component temperature rise as a function of the ambient temperature.
Heat conductivity (G) as a function of pitch and capacitor body thickness in mW/°C
Table 1
Heat conductivity
ORIGINAL PITCH (mm)
bmax
(mm)
5
7.5
3.5
1.5
3.0
4.0
2.0
3.5
4.5
2.5
3.5
5.0
2.5
4.0
5.5
3.0
4.0
6.0
3.5
4.5
6.5
−
5.0
Power dissipation and maximum component temperature rise
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a
function of the free air ambient temperature.
Power dissipation can be calculated in accordance with chapter “Introduction”, section “Maximum power dissipation”.
The component temperature rise (∆T) can be measured (see section “Measuring the component temperature” for more
details) or calculated by ∆T = P ⁄ G :
• ∆T = component temperature rise (°C).
• P = power dissipation of the component (mW).
• G = heat conductivity of the component (mW/°C).
1999 Apr 29
102
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
Measuring the component temperature
A thermocouple must be attached to the capacitor body; see Fig.26.
handbook, halfpage
thermocouple
CBA771
Fig.26 Mounting the thermocouple.
The temperature is measured in unloaded (Tamb) and maximum loaded
condition (Tc).
The temperature rise is given by ∆T = T c – T amb .
To avoid radiation or convection, the capacitor should be tested in a wind-free
box.
1999 Apr 29
103
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
Application note and limiting conditions
These capacitors are not suitable for mains applications as across-the-line capacitors without additional
protection, as described below. These mains applications are strictly regulated by safety standards and
therefore electromagnetic interference suppression capacitors conforming to the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (Up) shall not be greater than the rated DC voltage (URdc).
2. The peak-to-peak voltage (Up-p) shall not be greater than the maximum Up-p to avoid the ionisation inception level.
3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and
without ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied
by URdc and divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T
dU 2
dU
2 × ∫  --------  × dt < U Rdc ×  -------- 
dt
dt rated
0
T is the pulse duration.
The rated voltage pulse slope is valid for ambient temperatures up to 85 °C. For higher temperatures a derating factor
of 3% per K shall be applied.
4. The maximum component surface temperature rise must be lower than the limits in 0.
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a
capacitor breakdown (short circuit) increases, it is recommended that the power to the component is limited to
100 times the values mentioned in Table 1.
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series
connected with an impedance to the mains the applicant must guarantee that following conditions are fulfilled in any
case (spikes and surge voltages from the mains included).
VOLTAGE CONDITIONS FOR 6 ABOVE
ALLOWED VOLTAGES
Tamb ≤ 85 °C
85 °C < Tamb ≤ 100 °C
URac
0.8 × URac
Maximum temporary RMS overvoltage (<24 hours)
1.25 × URac
URac
Maximum peak voltage (Vo-p) (<2 s)
1.6 × URdc
1.3 × URdc
Maximum continuous RMS voltage
1999 Apr 29
104
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
Example
C = 330 nF - 63 V used for the voltage signal shown in Fig.27.
Up-p = 40 V; Up = 35 V; T1 = 100 µs; T2 = 200 µs.
The ambient temperature is 35 °C.
Checking the conditions:
1. The peak voltage Up = 35 V is lower than 63 V (DC).
2. The peak-to-peak voltage 40 V is lower than 2 × 2 × 40V (AC) = 113 U p – p .
3. The voltage pulse slope dU/dt = 40 V/100 µs = 0.4 V/µs.
This is lower than 110 V/µs (see specific reference data for each version).
4. The dissipated power is 16.2 mW as calculated with Fourier terms.
16.2 mW
The temperature rise for bmax = 4.5 mm and pitch = 5 mm will be --------------------------------- = 6.5 °C .
2.5 mW ⁄ °C
This is lower than 15 °C temperature rise at 35 °C; see Fig.25.
5. Not applicable.
6. Not applicable.
voltage
handbook, full pagewidth
Up
Up-p
time
T1
T2
CBA865
Fig.27 Voltage signal.
1999 Apr 29
105
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
MARKING
Product marking
COUNTRY OF ORIGIN: BELGIUM
handbook, halfpage
The capacitors are marked on the top with black ink
(see Figs 28 and 29), containing the following information:
1. Rated capacitance code in nF or µF
0.047
K 63
CBA091
2. Tolerance on rated capacitance: K = ±10%; J = ±5%
3. Rated (DC) voltage.
Fig.28 Example of marking for capacitors with
pitch = 5 mm (kinked and straight leads).
handbook, halfpage
470 K 100
CBA092
Fig.29 Example of marking for capacitors with
pitch = 5 mm (bent back leads) and
pitch = 7.5 mm (kinked and straight leads).
COUNTRY OF ORIGIN: PRC (PEOPLE’S REPUBLIC OF CHINA)
The capacitors are marked on the side with black ink
(see Fig.30), containing the following information:
handbook, halfpage
1. Rated capacitance code in nF or µF
100n
K100
2. Tolerance on rated capacitance: K = ±10%; J = ±5%
3. Rated (DC) voltage.
CBA465
Fig.30 Example of marking for capacitors with
pitch = 5 and 7.5 mm.
1999 Apr 29
106
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
Package marking
The package containing the capacitors is marked as shown in Fig.31.
Please note:
In due time BC COMPONENTS
will replace PHILIPS COMPONENTS
Barcode label marking
handbook, full pagewidth
1.
2.
LINE
MARKING EXPLANATION
3.
1
Manufacturer's name
4.
2
Country of origin
5.
3
Sub-family
4
Type description
5
Capacitance value in µF, tolerance, voltage
and climatic category (“IEC 60068-1”)
6
Batchnumber (only for capacitors from PRC)
7
• Country of origin: Belgium
6.
Preference origin code: A
Country of origin in code: 170 (Belgium)
Responsible production centre: HQ
Work order: WO
7.
8.
• Country of origin: China
Preference origin code: N
Country of origin in code: 260 (PRC)
Responsible production centre: 07
9.
10.
8
Product type description
9
Quantity and production period, year and week
code
10
Product code (12NC)
CCA337
Fig.31 Barcode label.
1999 Apr 29
107
BC Components
Product specification
Metallized polyester film capacitors
MKT 365/366/367
QUICK REFERENCE TEST REQUIREMENTS (see note 1)
TEST
PROCEDURE
(quick reference)
REQUIREMENTS
Robustness of leads
Tensile strength:
“IEC 60068-2-21”
load 10 N; 10 s
Bending:
“IEC 60068-2-21”
load 5 N; 4 × 90°
Resistance to soldering heat:
“IEC 60068-2-20”
solder bath: 260 °C; 10 s
Component solvent resistance
isopropyl alcohol; 23 °C; 5 minutes
no visible damage
legible marking
∆C/C ≤ 2%
∆tan δ ≤ 30 × 10−4; note 2
Robustness of component
Vibration:
“IEC 60068-2-6”
Shock:
“IEC 60068-2-27”
10 to 55 Hz; amplitude 0.75 mm or
acceleration 98 m/s2; 6 hours
half sinewave; 490
m/s2;
11 ms
∆C/C ≤ 3%
∆tan δ ≤ 30 × 10−4; note 2
Climatic sequence
Dry heat:
“IEC 60068-2-2”
16 hours; 100 °C
∆C/C ≤ 5%
Damp heat cyclic, first cycle:
“IEC 60068-2-30”:
Cold:
“IEC 60068-2-1”
∆tan δ ≤ 50 × 10−4; note 2
2 hours; −55 °C
Rins ≥ 50% of specified value
Damp heat, remaining cycles:
“IEC 60068-2-30”
Other applicable tests
Damp heat steady state:
“IEC 60068-2-3”
56 days; 40 °C; 90 to 95% RH
∆C/C ≤ 5%
∆tan δ ≤ 50 × 10−4; note 2
Rins ≥ 50% of specified value
Endurance (DC):
“IEC 60384-2”
2000 hours:
1.25 × URdc; 85 °C
1 × URdc; 100 °C
Heat storage:
“IEC 60384-2”
2000 hours; 100 °C
Resistance to soldering heat
with preheating:
“IEC 60384-2”
body temperature: 100 °C;
bath temperature: 260 °C;
dwell time: 5 s
∆C/C ≤ 5%
∆tan δ ≤ 30 × 10−4; note 2
Rins ≥ 50% of specified value
∆C/C ≤ 3%
∆tan δ ≤ 30 × 10−4; note 2
∆C/C ≤ 2% (C ≤ 10 nF)
∆C/C ≤ 1% (C > 10 nF)
∆tan δ ≤ 30 × 10−4; note 2
Notes
1. For detailed information, see “Type detail specification HQN-384-02/105”.
2. Measuring frequency 100 kHz for C ≤ 470 nF and 10 kHz for C > 470 nF.
1999 Apr 29
108